:Construction Of Cocopeat And Tray Washing Area At Anjanthali Farm Of Mhu, Karnal
Tender Value
3.86 Lakhs
Estimated cost
Bid Submission
12 Oct 2022
0 days left
EMD
7720
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
karnal → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
:Construction Of Cocopeat And Tray Washing Area At Anjanthali Farm Of Mhu, Karnal
BOQ
| Sl. No. | Item Description |
| 1 | Description and details |
| 2 | HSR ITEM NO. 4.14 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressingof sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.4.14.1 All kinds of soil. |
| 3 | HSR ITEM NO. 6.1 A. CEMENT CONCRETE (CAST IN SITU)Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: HSR ITEM NO. 6.1.6 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size |
| 4 | HSR NO. 6.14.1Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level:1 : 1. 5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): graded stone aggregate 20 mm nominal size) |
| 5 | HSR NO. 7.21.2BRICK WORKBrick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:6 (1 cement: 6 coarse sand) |
| 6 | HSR NO. 11.6.215 mm cement plaster on the rough side of single or half brick wall of mix :1 :6 (1 cement: 6 fine sand) |
| 7 | HSR NO. 9.33Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %)total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever required. |
| 8 | HSR NO. 13.30.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 13.30.1 Hot finished welded type tubes |
| 9 | HSR NO. 10.1Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. |
| 10 | HSR NO. 10.7Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 |
| 11 | HSR NO. 6.15.1 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mm nominal size) |
| 12 | HSR NO. 11.4.2 1 O mm thick cement plaster1 :3 (1 cement: 3 fine sand) |
| 13 | HSR NO. 6.33.6Steel reinforcement for R.C.C. work, where not included in thecomplete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth levelNote:- Reinforcement shall be measured in length includinghooks, if any, separately for different diameters as actually usedin work , excluding overlaps. Wastage, overlaps, couplings,welded joints, spacer bars, chairs, stays, hangers and annealedsteel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
AI Tender Summary
Tender Timeline
Sep 22, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 13, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender