Repair / Maint Of Puf Panels And Connected Items At Julley Airmen Mess And Near By Areas At 21 Wing Af Stn Leh
Tender Value
19.25 Lakhs
Estimated cost
Bid Submission
15 Oct 2022
0 days left
EMD
38500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Leh → Ladakh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair / Maint Of Puf Panels And Connected Items At Julley Airmen Mess And Near By Areas At 21 Wing Af Stn Leh
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 06-Oct-2022 | Date corrigendum | Date | 08-Oct-2022 |
| 2 | 06-Oct-2022 | Other corrigendum | Other | 08-Oct-2022 |
| 3 | 08-Oct-2022 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 15-Oct-2022 |
| 4 | 13-Oct-2022 | 1 Other corrigendum | Other | 15-Oct-2022 |
BOQ
| Sl. No. | Item Description |
| 1 | Pre–cast cement concrete block masonry with solid blocks of type C–1, 1:3:6 (20 mm graded crushed stone aggregate) exc. 10 cm in width and setting in mortar 1:4, in and including demolition of old precast concrete block walling, pillars etc. built in cement mortar ,complete all as specified and directed by Engineer-in-Charge |
| 2 | Rendering 15mm thick on fair faces of brickor concrete surface in cement mortar 1:6 finished evev & smooth without using extra cement, complete all as specified and directed by Engineer-in- Charge. |
| 3 | Preparation plastered or unplasteted new wall surfaces and applying three coat of white washing, complete all as specified and directed by Engineer-in-Charge |
| 4 | Plain cement concrete ,1:4:8, type D-2, using 40 mm graded mechanically crushed stone aggregates as in foundations filling and mass concrete or in sub base to floor in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) , complete all as specified and directed by the Engineer in Charge. |
| 5 | Plain cement concrete, 1:2:4, type B–0, (using 12.50 mm graded crushed stone aggregate) , 25mm thick as in sub base and finishing the surface even and rough to receive the topping layer in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) , complete all as specified and directed by the Engineer in Charge. |
| 6 | First quality, Non skid ceramiccoloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sq.m but not exceeding 0.38 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in coloured cement to match the shade of tilesincluding dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premises,complete all as specified and directed by Engineer-in- Charge. |
| 7 | Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as in replacment , in and including taking down old damaged unservicable sheet in roof covering etccomplete all as specified and directed by Engineer-in-Charge. |
| 8 | Pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as in replacment, in and including taking down of old unservicable sheet in roof covering etc., complete all as specified and directed by Engineer-in-Charge. |
| 9 | Rolled section (Angle,Channel,T-section,MS Flate,Tubler pipes)as in framing for cladding,glazing and the like fixed with angle claets and connecting plates,etc including dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-In-Charge |
| 10 | Preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge |
| 11 | 60mm thick PUF panels in wall with 0.5mm prepainted galvalume sheet on both face/side including all fixing arrangements as in replacment of old damaged portion of wall panelling , complete all as specified and directed by Engineer-in-Charge |
| 12 | 40mm thick PUF false ceiling panels with 0.5mm prepainted galvalume sheet on both face/side including all fixing arrangementsas in replacment of old damaged portion of false ceiling panels , complete all as specified and directed by Engineer-in-Charge |
| 13 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm but each, complete all as specified and directed by Engineer-in-Charge. |
| 14 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n. exc. 4 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 15 | Door shutters with 60mm thick PUF panel with 0.5mm thick prepainted MS sheet on both side (Colour as approved by GE) including200mm aluminium tower bolt (2 Nos), aluminium sliding bolt 300mm (01 Nos), built in locking arrangement (mortice lock with handle) and handle 02 nos on both faces including chowkhat of angle 60 x 60 x 6mm fixed with 03 Nos (100mm) heavy duty hinges, complete all as specified and directed by Engineer-in-Charge |
| 16 | Anodised aluminium sliding window and ventilator with frame and shutters, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings per leaf suitable handle (1 No) with aluminium grill of size 50 x 50mm, complete all as specified and directed by Engineer-in-Charge |
| 17 | Sheet glass 5.5 mm thick oridinary quality and glazing with rubber packing to sliding windows in square not exceeding 0.50 sqm in each pane, complete all as specified and directed by Engineer-in-Charge |
| 18 | Aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed by Engineer-in-Charge |
| 19 | Note : Schedule of creditto be deducted on acceptances of bid.Details of Schedule of credit is given in tender documents |
AI Tender Summary
Tender Timeline
Oct 13, 2022
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 08, 2022
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Oct 08, 2022
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Completed
Oct 15, 2022
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
Completed
Oct 15, 2022
18:00 IST
Corrigendum-4 Issued
Clarifications on tender conditions and amendments issued.
CompletedOct 15, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 10, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender