Construction Of Shed In Front Of Old Canteen At Main Campus Nauni, Solan.
Tender Value
7.58 Lakhs
Estimated cost
Bid Submission
20 Sep 2022
0 days left
EMD
15000
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
solan → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Shed In Front Of Old Canteen At Main Campus Nauni, Solan.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil complete in all leads, lifts and carriage of material as directed by the Engineer-in-Charge. a). Ordinary rock. |
| 2 | Providing and laying in position cementconcreteof specified gradeexcluding the costofcentering and shuttering - All work up to plinth leveletc. complete in all respect as per Engineer-in-Charge.a)1:2:4 (one cement : two sand : 4 graded Stone) aggregate 20 mm nominal size. |
| 3 | Providing and laying in position cementconcreteof specified gradeexcluding the costofcentering and shuttering - All work up to plinth level complete in all respect as per satisfaction of Engineer-in-Charge.a) 1:5:10(one Cement : five sand : ten graded stone aggregate 20 mm (twenly milimetre) nominal size |
| 4 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessaryexcavation, levelling & dressing & finishing the top smooth. |
| 5 | Brick edging 7 cm wide 11.4cm deep to plinth protection with common burntclay F.P.S. (nonmodular) bricks of classdesignation7.5 includinggroutingwithcement mortar1:4 (one cement : four sand) complete in all respect as per satisfaction of Engineer-in-Charge. |
| 6 | Half brick masonry with common burntclay F.P.S. (non modular)bricksofclassdesignation7.5 in superstructure above plinth level up to all floor level with cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge. |
| 7 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a). In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 8 | M.S. Hollow pipe / Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. as required. complete in all respect as per satisfaction of Engineer-in-Charge |
| 9 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(TATA/ JINDAL MAKE) |
| 10 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(TATA/ JINDAL MAKE) |
| 11 | Providing and fixing precoated galvanised steel sheet Ridges plain (500 - 600mm) 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete in all respect as per satisfaction of Engineer-in-Charge.(TATA/ JINDAL MAKE) |
| 12 | Providing and fixing Welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Priming & Painting to be paid for separately) etc. complete in all respect as per satisfaction of Engineer-in-Charge. |
AI Tender Summary
Tender Timeline
Sep 09, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedSep 20, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 20, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender