Public Works Department-PWD has published Construction Of Alternate Road To Gujjar Colony Naurangabad Due To Acquisition Of Land For Iim Sirmour Km. 0 / 0 To 2 / 210 ( Actually Km. 0 / 0 To 2 / 230 ) Alongwith 63.00 Metres Rcc Box Cell Bridge ( Sh- Construction Of Embankment With Approved M. Submission Date for this Tender is 09-09-2022. Wall construction Tenders in Sirmaur Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Construction of embankment with approved materials obtained from borrow pit with all lifts & leads, transporting to site, spreading, grading to required slope & compacted to meet the requirement of table 300.1 & 300.2 in all leads & lifts as per technical specification clause 301.5 including carriage of materials within all leads,lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge |
| 2 | Earth work in excavation for structure in all depths as per drawing & technical specification for Rural Road August 2004 clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleteruious materials & disposal in all leads & lifts including dressing of sides & bottom & back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollation etc. and to protect stability of hill side rock shall be excavated with chiselling and wedging out rock ( where blasting is prohibited ). All earth work in cutting/excavation including rock excavation shall be carried out true to lines, grades, side slopes, width, camber super elevation and level as shown on the drawing or as directed by the Engineer-in-Charge hauling & stacking of materials useful for construction at suitable sites & safe disposal of unsuitable cut materials in specified manner tramming filling of unevenness blindage & finishing of the road to specified dimension or as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to sping seepage rain and other causes, it shall be remove by suitable diversion bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. Any loss to the public or private property during the course of excavation shall be the whole responisibility of the contractor which shall have to be duly compensated by him at his own cost in all cases. |
| 3 | Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 4 : 8 ( One cement : four sand : eight graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ) for plain/ reinforced concrete work in open foundation complete as per drawing & technical specification clauses 802, 803, 1202 & 1203 including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge. |
| 4 | Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 3 : 6 ( One cement : three sand : six graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ) for plain/ reinforced concrete work grade M-10 ( ten )in open foundation complete as per drawing & technical specification clauses 802, 803, 1202 & 1203 including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge. |
| 5 | Providing & laying plain/reinforced cement concrete Mechanically mixed & Vibrated in Sub-structure complete as per drawings & technical specification clauses 802, 803, 1202 and 1203 Plain cement concrete grade M-15 ( fifteen ) nominal mix 1:2.5:5 ( One cement : two & half sand : five graded stone aggregate ) including cost of form work & curing complete including carriage of materials within all leads, lifts & otherincidentialcomplete as per entire satisfaction of the Engineer-in-Charge. |
| 6 | Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 2 : 4 ( One cement : two sand : four graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ) for plain/ reinforced concrete work in sub-structure complete as per drawing & technical specification clauses 802, 804, 805,806, 807,1202 & 1204 in all height & depth, including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge. |
| 7 | Providing & laying reinforced cement concrete Mechanically mixed & Vibrated in super-structure as per drawing & technical specification clauses 800, 1205.4 & 1205.5 reinforcement cement concrete M-25 grade ( design mix ) 1 : 1.5 : 3 ( One cement : one & half sand : three graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size )in all height & depth, including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge. |
| 8 | Supplying, fitting & placing HYSD bar reinforcement in Super structure complete as per drawing & technical Specifications clause 1002, 1010 & 1202 including cost of binding wire including carriage of materials within all leads, lifts & other incidential charges & as per directionof Engineer-in-Charge. |
| 9 | Providing & laying boulder apron laid in wire crates with 4 mm ( four milimetre ) dia G.I. wire conforming to IS: 280 & IS:4826 in 100mm x100mm ( One hundred into one hundred milimeter ) mesh ( woven diagonally including 10% ( ten percent )extra for laps & joints laid with stone boulders weighting not less than 25 ( twenty five ) kilogram each as per drawing & technical Specification clause 1301, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 10 | Providing & laying filter media with granular crushed aggregate as per specification to a thickness of not less than & bigger size towards the wall & providing over the entire surface behind abutment, wing walls height compacted to firm condition complete as per drawing & technicalspecification clause 1204.3.8, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 11 | Back filling behind abutment, wing walls & return walls complete as per drawing & technical specification clause 1204.3.8, Granular materials including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 12 | Providing weep holes in brick masonry/ stone masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia (One hundred milimeter ) PVC pipe extending through the full width of the structure with slope of I V ( One vertical ) : 20 H ( Twenty horizonuial ) towards drawing face complete as per drawing Technical Specifications clauses 614, 709, 1204.3.7 including hauling of materials within all leads & lifts & other incidential charges & as per direction of Engineer-in-Charge. |
| 13 | Providing & laying reinforced cement concrete pipe NP2 as per design in single row, culverts on first class bedding of granular materials in single row including fixing collars with cement mmortar 1 : 3 ( One cement : three sand ) but excluding excvavation, protection wall, back filling, concrete & masonry work in head walls & parapets as per drawing & technical specification clause 1106of R.C.C. following pipes :- |
| 14 | 600 mm ( Six hundred milimetre ) dia R.C.C. pipe NP2 as per design, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 15 | 900 mm ( Nine hundred milimetre ) dia R.C.C. pipe NP2 as per design, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 16 | Construction of Reinforced cement concrete railing of M-25 ( twenty five ) Grade in-situ with 20 mm ( twenty milimeter ) nominal size aggregate, true to line & grade, to lurence of vertical reinforced cement concrete post not to exceed 1 ( One ) in 500 ( five hundred ), centre to centre spacing between vertical post not to eceed 2000 m ( Two thousand meter ), leaving adequate space between vertical post for expansion, complete as per approved drawings & technical specifications, including hauling/ carriage of all labour equipment & materials to various locations through all modes of transpportions in all leads & lifts to the entire satisfactionof the Engineer-in-Charge. |
| 17 | Providing & fixing Drainage spouts complete as per drawing & Technical Specifications including hauling/ carriage of all labour equipment & materials to various locations through all modes of transportations in all leads, lifts to the entire satisfactionof Engineer-in-Charge. |
| 18 | Providing & laying a burried expansion joints, expansion gap being 20 mm ( twenty milimeter ) covered with 12 mm ( twelve milimetre ) thick 200mm ( two hundred milimetre ) wide galvansised weldable structural steel plates as per IS 2062, placed symmetrical to centre line of the joints, resting freely over the top surface of the deck concrete, welding of 8 mm ( eight milimetre ) dia, 100mm ( One hundred milimetre ) long galvanised nails spaced 300mm ( three hundred milimetre ) centre to centre along the centre line of the plate, all as specified in clause 2604, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 19 | Providing & fixing in position 20 mm ( twenty milimetre ) thick premoulded joint filler in expension joints for fixed ends of simply supported spans, covered with sealant complete as per drawing & technical specification , including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 20 | Painting two coats including prime coat with epoxy paint of approved brand on new plastered/ concrete/ steel surface after through cleaning of surface to give an even shade as per drawing & technical specification clause 1701, including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 21 | Preparation of sub grade by dressing to camber ( Earth work for the cutting involved for sub grade to be paid for separately depending upon the claiisification of soil ) complete as per HP.PWD., specification including haulage of materials in all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 22 | Consolidation of Sub-grade with road roller including making good the undulation etc. with earth or quarry soil etc. & re-rolling the sub-grade complete as per HP.PWD., Specification, 1990 Volume-I including haulage of materials in all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 23 | Construction of granular Sub-base by providing well graded materials, spreading in uniform layers with tractor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification clause 401, for Grading-I ( one ) materials including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 24 | Providing, laying, Spreading & compacting stone aggregate of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 ( eighty to one hundred ) KN in stages to proper grade & camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering & compacting to the required density grading-2 ( two ) as per Technical Specification clause 405including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 25 | Providing, laying, Spreading & compacting stone aggregate of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 ( eighty to one hundred ) KN in stages to proper grade & camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering & compacting to the required density grading-3 ( three ) as per Technical Specification clause 405including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 26 | Providing & applying primer coat with bitumen emulsion (SS-I) on the prepared surface of granular base including cleaning of road surface & spraying primer @ 0.85 Kg/Sqm ( zero point eightfive kilogram per square metre ) using mechanical means as per Technical Specification clause 502, including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 27 | Providing & applying tack coat with nitumen emulsion ( RS-I ) using emulsion distributor 0.276 Kg/Sqm. ( zero point two seven six kilograme per Square metre ) on the prepared surface dry & honary bitumen surface cleaned with hydraulic broom as per Technical Specification clause 503, using mechanical meansincluding carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 28 | Providing & laying bituminous concrete with 100-120 TPH ( One hundred to one hundred twenty Toone per hour ) batch type hot mix plant producting an average output of 75 ( Seventy five ) tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 ( five point four to five point six ) per cent of mix & filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level & alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause 509 complete in all respects, including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 29 | Providing & laying of hot applied thermoplastic compound 2.5mm ( Two point five milimetre ) thick including effectorising glass beads @ 250 grms( two hundred fifty grams ) per square metre area thickness of 2.5mm( Two point five milimetre ) is exclusive of surface applied glass beads as per IRC:35. The finish surface to be level, uniform & free from streaks & holes, including carriage of materials within all leads, lifts & other incidentals complete as per entire satisfaction of the Engineer-in-Charge. |
| 30 | Reinforced cement concrete M15 grade kilometre stone/ Local stone of standard design as per IRC:8 fixing in position including painting & Printing etc. as per drawing and Technical Specification clause 1703, Ordinary Kilometer stone ( Precast ) including carriage of materials within all leads, lifts &other incidential complete as per entire satisfaction of the Engineer-in-Charge |
| 31 | Reinforced cement concrete M15 grade kilometre stone/ Local stone of standard design as per IRC:8 fixing in position including painting & Printing etc. as per drawing and Technical Specification clause 1703, 200 mets ( two hundred metres ) stone ( Precast ) including carriage of materials within all leads, lifts &other incidential complete as per entire satisfaction of the Engineer-in-Charge |
| 32 | Reinforced cement concrete M15 grade boundary pillars/ local stone of standard design as per IRC:8 fixing in position including painting & Printing etc. as per drawing and Technical Specification clause 1703, including carriage of materials within all leads, lifts &other incidential complete as per entire satisfaction of the Engineer-in-Charge |
| 33 | Providing & fixing of retro-reflectorised cautionary, mandatory & informatory sign as per IRC 67 ( Sixty seven ) made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm ( One point five milimeter ) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm ( seventy five milimeter into seventy five milimeter into six milimeter ) firmly fixed to the ground by means of properly designed foundation with M15 (fifteen ) grade cement concrete 450 mm x 450 mm x 600 mm , 600 mm ( Four hundred fifty milimeter into four hundrted fifty milimeter into six hundred milimeter, six hundred milimeter ) below ground level as per drawing and Technical specification clause 801 600 mm ( six hundred milimeter ) equilateral triangle board, including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
| 34 | Providing & fixing of retro-reflectorised cautionary, mandatory & informatory sign as per IRC 67 ( Sixty seven ) made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm ( One point five milimeter ) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm ( seventy five milimeter into seventy five milimeter into six milimeter ) firmly fixed to the ground by means of properly designed foundation with M15 (fifteen ) grade cement concrete 450 mm x 450 mm x 600 mm , 600 mm ( Four hundred fifty milimeter into four hundrted fifty milimeter into six hundred milimeter, six hundred milimeter ) below ground level as per drawing and Technical specification clause 801 including carriage of materials within all leads, lifts & other incidential complete as per entire satisfaction of the Engineer-in-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
