|
| 1 | Supply of earth including royalty, excavation and carriage by mechanical transportupto 5 KM and banking the same in layers not exceeding 20cm in depth breaking clods, rolling each layer with ½ tonne roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonne and dressing up in embankment for road, flood bank and guide bank or filling up ground depression lead upto 50m and lift upto 1.5m in all kind of soil. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 6 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor II level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. |
| 8 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 9 | Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 10 | Providing and fixing rubber tile flooring 25mm thick made of SBR(Styrene Butadiene Rubber) with interlocking arrangement and adhesive all complete and size as approved by the Engineer-in-charge. |
| 11 | Precast Reinforced cement concrete Bench (Chair Type Bench with hand rest). The bench consist of 2 Nos. L-shape base support in cement color of thickness – 80 mm, back height – 890 mm & front height – 450mm, Base width – 690 mm, as per sketch and 1 Nos. reinforced concrete planks in red color of size 1500x320x50mm, and 1 No. of reinforced concrete plank in red color of size 1500x425x50mm. Manufactured by using M-30 grade of concrete & reinforced suitably to prevent damage during handing, transportation, erection & long use. All parts are joined together with galvanized nuts & bolts of suitable size. All bolts are sealed after assembly. Seating length of the bench – 1500 mm. seating height of the bench – 450 mm. Total height of the bench – 890 mm. Bench top and back planks are treated with special anti-corrosive, water proof coating so as to make surfaces glossy and water proof. |
| 12 | Providing and fixing of AERIAL STROLLER/HD HEALTH WALKER make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/ Grand Slam as approved by Engineer-in-charge. HD Health Walker of size 1070x615x1509mm fabricated with main post of 114mm and 4.00mm thick pipes made of hot roller tubular steel and hot dipped galvanized and powder welded coated using Akzo Nobel or equivalent of 80-120mm micron thick.All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with in welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welded points prior to finishing. All complete as per technical specifications of manufacturer. The installation requires the poles to be fitted using Anchor fasteners on a concrete foundation of minimum strength M-25, cement concrete blocks of required size, as per direction given by engineer-in-charge, finished below ground level |
| 13 | Providing and fixing of ABS BOARD/HD SIT UP STATION make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. HD Sit up Station of size 1400x1366x650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-100 micron thick. All joints of pipe are4 robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Sit up boards and Base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm, colourful and UV resistant and environmental friendly.All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 14 | Providing and fixing of CIRCULAR PULL UP STATION make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. HD CIRCULAR PULL UP STATION of size 2500x760x1500mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. The rails of dia 42mm and length of 2500mm and welded on the post with a 42mm dia support rods. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paints are applied at all welding points prior to finishing. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equivalent on to it and cover nuts and bolts with the base plate. |
| 15 | Providing and fixing of AERO RIDER HD HORSE RIDER STATION make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. HD HORSE RIDER station size 1417x668x1425mm fabricated with main post of 114mm and 4.00mm thick made of hot roller tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120mm micron thick.All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLDPE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover. |
| 16 | Providing and fixing DOUBLE SHOULDER EXCISER/PULL DOWN CHALLENGER make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. Pull Down Challenger of size 2572x805x2187mm fabricated with main post of 114mm and 4.00mm thick made of hot roller tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120mm micron thick.All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLDPE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover. |
| 17 | Providing and fixing of LEG EXTENSION/LEG STRETCH make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. LEG STRETCH of size 932x811x1163mm fabricated with main post of 114mm and 4.00mm thick and rails made from 32mm dia pipes and thickness of 2.4mm pipes made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Base plate plastic of 8mm, colorful and UV resistant and environmental friendly. All open ends of pipe to be closed by LLDPE caps for user friendly.The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover.. |
| 18 | Providing and fixing of DOUBLE BALANCING BEAM/HD BALANCE BEAM H make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. HD DOUBLE BALANCE BEAM of size 3695x1177x357mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. The balance beam composed of 3 beams of length 1175mm and dia 114mm each which is installed at an angle to provide a challenge in balancing forusers thereby improving the mobility and strengthening the calf muscles. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 19 | Providing and fixing of FOREARM TWIRL/TAI CHI SPINNERS make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. FOREARM TWIRL/TAI CHI SPINNERS TAI CHI SPINNERS of size 1150x1150x1650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. The circular spinners made from 32mm dia hot dipped galvanized steel rods and welded on to the post using a 6mm dia hot dipped galvanized steel supports. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury. Bearing used shall be made maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. on ground with concrete of minimum strength M-25 and J shaped The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 20 | Providing and fixing of CHEST PRESS/SEATED CHEST PRESS make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. SEATED CHEST PRESS of size 1957x733x2058mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Handgrip to be made from high quality rubber. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 21 | Providing and fixing of SHOULDER TWIRL/BIG SHOULDER WHEEL make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. BIG SHOULDER WHEEL SEATED CHEST PRESS of size 857x850x1815mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 22 | Providing and fixing of OVATE STEPPER/HD ELLIPTICAL CROSS TRAINERS make ARIHANT/ KOMPAN/ LANDSCAPE/ KOOCHIE (HUGO)/Grand Slam as approved by Engineer-in-charge. HD ELLIPTICAL CROSS TRAINER of size 1148x585x1486mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 23 | Providing and fixing of HIP TWISTER/HD WAIST TWISTER make (HUGO)/Grand Slam as approved by Engineer-in-charge. HD waist twister of size 1463x1310x1258mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Rotating and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. |
| 24 | Fabrication supplying and erection of flange mounted hot dip Galvanized octagonal Poles of 5 Mtr. Height made from 3mm thick steel plate having bottom Dia of 130 mm & top Dia of 70mm complete base plate of size 200mm x 200mm x12mm thick on existing cement concrete pedestal as required including suppling andwelded at suitable height as per direction of Engineer-in-charge. 2 Nos. washer, nuts and locking arrangement completed as required (Make Bajaj/Crompton/Phillips/Wipro/havells) |
| 25 | Supplying and fixing of 4 Nos. 20mm x 700mm long GI foundation bolt (EN 8 grade) with nuts washer including 2 Nos. template of 3mm thick size 200mmx200mmx12mm thick with 4 Nos. 16mm Dia holes to match with PCD of poles base plate as required (Make Bajaj/ Crompton/ Phillips/ Wipro/havells) |
| 26 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 27 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size). |
| 28 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 29 | Centering and shuttering including strutting, propping etc. and removalof form for :Foundations, footings, bases of columns, etc. for massconcrete |
| 30 | Supplying, Installation, Testing and Commossioning of 30 watts smart integrated all in one solar light of Highly efficient IP65 LED Solar Lighting System with built-in high efficiency Solar Panel, LED Light and 12.8 V 36 AH lithium fesso phosphate (4-Fe PoD) rechargeable Bis certified cells, future long life battery with high efficiency microprocessor-based charge controller, p/r motion sensor and compact in size to be mount on pole top complete etc. as required.(Make Bajaj/Crompton/ Phillips/Wipro/havells) |
