Supply, Installation, Testing And Commissioning Of Electro-Mechanical Equipments At Water Supply Scheme Khenebugh - Wss Khennibugh ( Adv. Cost: Rs. 16, 85, 000 / - ) 2 Supply, Installation, Testing & Commissioning Of Submersible Pumping Unit As Per Is 8034 Withfollowing Specification Are As Under:Pump: Efficiency = Not Less Than 50% Speed = 2900 Rpm Type Of Pump = Mixed Flow. Typerest Specifications As Per Clause -1 Of Sbd Motor Rating =25Hp 3 Supply, Installation, Testing And Commissioning Of Horizontalpumping Unit As Per Is 1520 With Following Specification:-Pump:- 1.Type :-Horizontal Monoblock Material Of Construction1.Impeller:- S.Steel2.Shaft:-Ss410 Motor Rating :5 Hp Or Sutible For Above Parameters Manufactures Test Certificate To Be Apended And Detailed Specification As Per Cluase 5 Of Of Sbd 4 Providing / Supplying And Fitting Ofg.I Flanged Rising Main At Site. The Pipe Shall Be Hot Dip Galvanized, Class-C Confirming To Is 1239. The Job Includes Providing And Fitting Of M.S Flanges Conforming To Bis 6392 / 1997 Table 17 ( Rating Pn16 ) . The Flanges Shall Be Double Welded Both From Inside And Outside Of The Pipe Using Standard Electrode Of Reputed Make.Flanges ( As Per Is 6392 / 1997 Table:17 ) Thickness Shall Conform To Is 6392 Part 1St Table-17. The Flange Welding Shall Be Carried Out In Double Layers Using Reputed Make Electrodes To Form Strong Welding Joint.Welding Electrodedc Arc Welding Using Welding Electrode Having Diameter Not Less Than 4Mm.Nuts And Boltsnuts And Bolts ( Conforming To Is:1363 Part 1St ) Rubber Insertion Gasketsrubber Insertion Gaskets ( Conforming To Is: 638 / 79 ) To Be Used Between Flanged Joints. The Rising Main Is To Be Laid As Per The Instructions Of The Engineer In Charge And Site Requirement. The Size Of The Pipe Is Given Below:Size : Dn 100Class: C ( Heavy ) 5 Size : Dn 80Class: C ( Heavy ) 6 Earth Work In Excavation By Manual Means In Trenches For Foundation, Drains, Pipes, Cables ( Not Exceeding 1.5 M In Width ) And For Shafts, Wells, Cesspits And The Like Not Exceeding 10 Sqm On Plan, Including Dressing Of Sides And Reaming Of Bottom Lift Upto 1.5 M, Including Getting Out Excavated Earth And Disposal Of Surplus Excavated Earth As Directed. ( All Kinds Of Soil 01 Meter From Cutting Edge ) 7 Filling Available Excavated Earth In Trenches, Plinth, Sides Of Foundation Etc. In Layers Not Exceeding 20 Cm In Depth, Consolidating Each Deposited Layer By Reaming And Watering, Lead Upto 50 M And Lift Upto 1.5M. 8 Fabrication, Providing And Fitting Of Split Type Ms Clamps10 Mm Thick, 2 Ft Long And 3 Inch Wide For Lowering And Holding Of Pumping Unit Fitted. The Job Includes The Cost Of Required Size Of Nuts And Bolts. Size: 80Mm 9 Fabrication, Providing And Fitting Of90-120 Degree Bend / Elbowto Be Fabricated Out Ofg.I Pipe, 1 M Lengthand Flanged On Both Ends Ato Make It Leak Proof. The Flanges Shall Be M.S Flanges Conforming To Bis 6392 / 1997 Table 17 ( Rating Pn16 ) And Welded On Both Sides. The Job Includes Nuts, Bolts, Gaskets Etc As Per Site Requirement.Size:Dn 80Class: C 10 Size:Dn 100Class: C 11 Cutting Of Hot Dip Galvanized G.I, Pipe Across The Section By Dint Of Pipe Cutter / Gas Cutter. The Job Also Includes Providing And Welding Of M.S Flanges To The Two Ends Of Pipe. The Thickness Of Flange Shall Conform To Is 6392 Part 1St Table-17. The Flange Welding Shall Be Carried Out In Double Layers Using Advani / Esab / L&T- Ss Bond Make Electrodes To Form Strong Welding Joint By Dint Of Dc Arc Welding. The Job Further Includes Providing And Fitting Of Nuts And Bolts ( Conforming To Is:1363 Part 1St ) And Rubber Insertion Gaskets ( Conforming To Is: 638 / 79 ) To Be Used Between Flanged Joints. The Size Of Pipe Is Given Below:Size: Dn80pn:1.6 / 16 12 Size: Dn 100Pn:1.6 / 16 13 Fabrication, Providing And Fitting Of Y- Junction Having 1M Length Of Each Armto Be Fabricated Out Ofhot Dip Galvanized G.I, C-Class Pipe. The Job Also Includes Providing And Welding Of M.S Flanges To The Ends Of Each Arm. The Thickness Of Flange Shall Conform To Is 6392 Part 1St Table-17. The Flange Welding Shall Be Carried Out In Double Layers Using Reputed Make Electrodes To Form Strong Welding Joint By Dint Of Dc Arc Welding. The Job Further Includes Providing And Fitting Of Nuts And Bolts ( Conforming To Is:1363 Part 1St ) And Rubber Insertion Gaskets ( Conforming To Is: 638 / 79 ) To Be Used Between Flanged Joints. The Size Of The Y- Junction Is Given Below :Size : Dn 80, Class - C 14 Fabrication, Providing And Fitting Of Washout Tee With Arm Length 1.2 Feet Each. The Tee Shall Be Fabricated Out Of G.I Pipe With M.S Flanges Conforming To Bis 6392 / 1997 Table 17 ( Rating Pn16 ) Fastened With Weld Joints On Three Ends. Size: 100Mmclass: C Class 15 Size: 80Mmclass: C Class 16 Providing And Fitting Of Ductile Iron Double Flanged, Non-Rising Spindle Soft Seatedglandless Gate / Sluice Valves As Per Is14846 For Regulating The Water Supply Outside The Pumping Units .The Body And Bonnent Of The Valve Shall Be Of Ductileiron, Wedge With Fully Vulcanized Epdm Rubber ( Approved For Drinking Water ) And Nbr Seal. The Gate / Sluice Valve Shall Be Compatible For Buried Applications And Shall Be Safe To Install In Both Horizontal And Vertical Positionsit Shall Have Electrostatic Epoxy Coating ( Approved For Drinking Water ) Both Inside And Outside Of The Valve. The Valve Shall Be Supplied Along With Hand Wheel.Cost On Account Of Nuts, Bolts, Gaskets, Etc Required For The Job Is Included In The Scope Of Work.The Job Includes Providing And Fitting Of 02 Nos. M.S Flanges Perfectly Adaptable To The Inbuilt Flanges Of The Valve Which Shall Be Fitted With Rising Main Of The Pumping Unit At Appropriate Spots As Per Site Requirement. Size: Dn 100Pn:1.6 / 16 17 Size: Dn80pn:1.6 / 16 18 Providing And Fitting Ofductile Iron Double Flanged, Slanted Seatswing Check Valve ( Nrv ) As Per Is 5312. The Body Shall Be Of Ductile Cast Iron With Fully Encapsulated Vulcanized Epdm Rubber ( Approved For Drinking Water ) . The Valve Shall Be Compatible For Buried Applications And Shall Be Safe To Install In Both Horizontal And Vertical Positions.It Shall Have Electrostatic Epoxy Coating ( Approved For Drinking Water ) Both Inside And Outside Of The Valve.Cost On Account Of Nuts, Bolts, Gaskets, Etc Required For The Job Is Included In The Scope Of Work.The Job Includes Providing And Fitting Of 02 Nos. M.S Flanges Perfectly Adaptable To The Inbuilt Flanges Of The Valve Which Shall Be Fitted With Rising Main Of The Pumping Unit At Appropriate Spots As Per Site Requirement. Size: 80Mmpn: 1.6 / 16 19 Size: Dn100pn: 1.6 / 16 20 Providing, Fitting, Testing And Commissioning Of Dn 50, Pn 1.6 / 16Arv ( Air Release Valve ) As Per Is 14845 To Be Fitted Tog.Irising Main ... The Arv Shall Have The Following Specifications: -I. Valve Type -Single Chamber, Single Orifice.Ii. End Connection-Flanged Ends To Is 1538 Iii. Working Temperature- 70Oc To 550 C Iv. Test Pressure - Body / Seat 2.5 X Pnv. Sealing Ring -Epdmvi. Construction-Ductile Iron With Stainless Steelfloatsvii. Coating -Epoxy With Corrosion Resistance Besides The Above Works, The Job Also Cost On Account Of P / F R.I Gasket, Nuts And Bolts Required For Installation Of Arv And Arrangement Of Gas Cutter / Welding Set At Site. 21 Providing, Installation Andtestingof Manual Type Triple Spur Gearchain Pulley Block Along With Monorail Gearedtravelling Trolleyhaving Following Features. Gears:- The Hoist Shall Have Precision Machine Case Hardened Alloy Steel Gear Mounted On Bearings And Housed In A Dust Proof Gear Box. The Lubrication Of Gears Should Be Of High Viscosity And Temperature For Longer Life Of Gears.Load Chain:-The Load Chain Be Made Of High Tensile Alloy Steel Having Wear Resistance And Greatest Mobility. The Chain Should Be Accurately Collaborated, Tested And Have Adequate In Built Factor Of Safety For Safer Operation.Load Chain Wheel:- The Load Chain Well Should Be Double Ball Bearing Supported Andspecially Designed, Perfectly Machined Wheel Providing Correct Grip Of Load Chaintomakes The Hoist Most Safe And Reliable Against Any Failure. The Main Specifications Of C.P Block Are Given Below : Make = Reputed Makecapacity=3Ton No. Of Load Chain Falls = 2 Or Above Min. Height Of Lift = 6 M 22 Supply, Installation, Testing And Commissioning Of Polymeric Gang Operated Air Break Switch, Outdoor Type, Triple Pole, Suitable For Vertical Installation, Single Break Provided With Locking Arrangement At Both On And Off Position Consisting Ofht Post Double Insulator, Copper Or Copper Alloy High Pressure Heavy Contact Assembly, Rod With Bearings , Operating Handle And 2 Length Of 32Mm Dia. Gi Pipe Conforming To Is 1818 1961, 06 No. Of Insulators, Rated Voltage 11Kv 200A Complete As Per Is Specs. 23 Supply, Installation, Testing And Commissioning Of 11Kvpolymer Fuses Sethorn Gap3-Phase 200 Asuitable For Vertical Installation . 24 Supply And Fitting Of 11 Kv Polymeric Composite Pin Insulator 12 Kv, 5Kn, Lighting Impulse 75Kv Positive, And 80 Kv Negative , Creepagedistance 320 Mm 25 P / F Of Galvanized Nuts, Bolts Of Various Sizes As Per Site Requirement. 26 Providing And Fitting Of Acsr As Per Is 398 ( Part-2 ) 1996 For 50 Sq.Mmacsr ( Galvanised Steel Reinforced ) For Fitment Of Various Accessories 27 Fabrication, Providing And Fitting Ofmodularmotor Control Panel Of Appropriate Size Fabricated Out Of 14 Swg Sheet Having Required Openings / Vents And Protection Class : Ip-55 & Fitted With Accessories As Under:Mu-G 10 Rest Specifications As Per Cluase - 43-Bof Sbd 28 Fabrication, Providing And Fitting Ofmodularmotor Control Panel Of Appropriate Size Fabricated Out Of 14 Swg Sheet Having Required Openings / Vents And Protection Class : Ip-55 & Fitted With Accessories As Under:Mu-G 30 Rest Specifications As Per Cluase - 43-Eof Sbd 29 Providing, Fitting, Testing And Commissioning Ofvoltage Stabilizeras Per Specifications Below: Type Of Voltage Controller: Manually Operated Copper Wound, 3-Phase, Ac Power Supply Multi Step.Type Of Regulator: Double Plate Type With Electrolytic Copper Contacts.Input Voltage : 250-400 Volts. ( 3 Phase ) Output Voltage : 400 ±10% Volts.Frequency : 50±3 C / S.Rest Specifications As Per Clause - 44 Of Sbdrating::50Kva 30 Providing And Fitting Of 3-Core Flatsubmersible Copper Cable Conforming To Is: 694 ( Part 1St ) – 1964 & Is: 694 ( Part 2Nd ) - 1964 For Submersible Pumping Unit And Other Electrical Equipments . The Cable Connections Terminal Shall Be Fitted With Copper Thimbles Of Required Size. Size 10 Sq.Mm 31 Size: 6 Sq.Mm 32 Providing And Fitting Of 3 / 3.5 / 2-Core, Xlpe Armoured Aluminium Cable Conforming To Is: 7089 Part 1St As Service Line From The Ht Transformer To Control Panel Including Necessary Thimbling, Crimping, Taping Etc.Note:- The Cable Terminal Ends For Connection To Switchgear At Various Requisite Points Shall Be Al. Thimbles Of Dowel’S Make And Of Appropriate Size And Connected By Hydraulic Crimp Tool Only.10Sqmm, 2 Core, Lt , 1.1 Kv 33 P / I Of Earthing Station For Substation, Lt Panel, Dg Set And Stabilizer Comprising Of Company Fabricated Earthing Electrode As Per Is: 3043. The Job Includes Auguring Of Bore Of Required Dia / Depth For Installation Of Electrode Along With Backfill Compound Mixed With Soil And All Other Items Required Thereof For Achieving The Best Result. The Job Includes Connecting Of Electric Gadgets Through Gi Strip As Per Relevant Standards.Safe Earthing Electrode Size:80 Mm Dia , Length :2000 Mmback Fill Compound :30 Kg 34 Providing, Installation, Testing And Commissioning Of Area Lighting 120 Watt Led ( Street Light Type ) On Top Of Octagonal Pole Vide Item No.36Having Following Specs:Input: 90-240 V 50 Hzpower Factor: >0.9Colour Temperature: 4K - 6.5Kbeam Angle: 120° - 170°Lumens: >12000Operating Temperature: -20°C To 60°Cthe Led Is Pressure Die Cast Aluminum Housing With Power Coated Finish And Having Ingress Protection Up To Ip-68.The Led Is To Be Properly Fitted On The Arm Of The Pole And Connected To The Copper Wire As Directed. 35 Supply, Installation, Testing & Commissioning Of 1000Va Full Sine Wave Power Inverter ( Make: Microtek / Luminous ) Including Providing / Installation Of 12V, 180Ah Tubular Inverter Battery With Trolley And Cover. ( Make: Amaron / Exide ) With 2-Core 6Mm2 Cu Wiring As Per Site Requirement Along With Other Accessories Like Ss-Combine ( 02 No’S ) , 3-Pin Plugs Etc Of Reputed Make For Proper Fitment And Installation Of The Item. 36 Providing, Laying & Fixing With Adhesive / Bonding Material Of Insulation Rubber Mats On The Floor Of The Pump House, Covering Area Around Electro-Mechanical Machinery For Safeguarding The Life & Limb Of The Workmen Due To Possible Leakage Of Current & Short Circuit. The Floor Surface Shall Be Made Good & Shall Be Free From Dust, Grease, Foreign Material & Moisture Free. The Mats Shall Be As Per Is 15652:2006 & Shall Have The Following Specifications: -Composition: Rubber ( Synthetic Mats For Electrical Purpose ) Thickness: - 2.5Mm Size: - 1M Wide.The Rubber Mats Shall Be Accepted With Manufacturers Test Certificate. 37 Tool Kit For Maintenance: -The Tool Kit For Maintenance Shall Comprise Of The Following And All The Items As Mentioned Below Shall Be Of :Providing Of Tool Kit Consists Of Following Items Restspecification As Per Clause - 46 Of Sbd 38 A ) Providing Of Good Quality Bedding For Night Stay / Shift Consisting Of: -I ) Mattress With Warm Cover Size 6X3 ( 6Kg ) - 02 No’Sii ) Quilt With Warm Cover Size 5X8 ( 6Kg ) - 02 No’Siii ) Pillows With Covers - 02 No’Siv ) Single Bed Warm Blankets With One Sided Fur- 02 No’Sthe Filling Material For Mattress, Quilt And Pillow Shall Be Of Good Quality Cottonb ) The Job Also Includes Providing Of Pressure Cooker 5Ltr 02 No’S, Steel Patila ( Utensil ) 5Ltrs 02 No’S, Cooking Heater 01 No., Room Heater 01 No., Steel Buckets 10 Litre Capacity 01 No., Plastic Bucket 10 Litre Capacity With Mug 02 No’S Each, Steel Glasses 06 No’S, Steel Plates With Large Spoons And Bowls 03 No’S Each, Cup And Saucer Set ( 01 No. Set ) And, 5Kg Gas Cylinder With Burner / Stove. All The Utensils Shall Be Of Prestige, Pigeon, Wonder Chef, United, Futura Make.The Job Also Includes Providing Of Thermo-Cool 15’X12’ Along With Excel Matting Of 15’X12’ Size. The Job Also Includes Providing Of Unbreakable Plastic Chair Table Set Consisting Of Chairs 04 No’S, Extra Heavy Table 01 No. The Job Also Includes Providing Of Good Quality Safety Door Locks ( 03 No’ 39 Providing Of Solar / Electrical Lantern Chargeable On Both Solar & Electrical 220V Supply. 40 Providing Of Bamboo Ladders 18 Feet Long Along With 15 Feet Long Link Rods And Ht Glove Pair ( 01 No Each ) 41 Providing Of 1 Kw Heat Convector For Operators For Winter Season. 42 P / Fof Lighting Points In 1.5 Sq.Mm Multi Strand Pvc Wire As Conductor To Be Laid / Carried In Pvc Channel / Conduit As Per Site Requirement Duly Fiited With Approperiate Fasteners. The Job Includes Providing And Fittingof All The Pvc Bends , Connectors Etc And5 Amp. Switch Fitted On Common Plate Flushed With Wallfor Beter Look Andbutton / Angle Holders To Be Fittedon With Led Blubs ( Energy Saver ) Inside The Pump House. 43 P / F Of Heating Points In 2.5 Sq. Mm Multi Stranded Pvc Conductor To Be Carried In Pvc Channel / Conduit As Per Site Requirement Duly Fiited With Approperiate Fasteners . The Job Includes Providing And Fitting Ofall The Pvcbends , Connectors 16 Amp. Switch Socket Combine To Be Fiited Flushed With Wall 44 P / F Of Distribution Board Of Sp & N ( Regal Gray ) With 1 No. Incoming And Outgoing 16 Way , Fitted With Mcb“C” Series6a- 12Nos. And 16 Amp- 4Nos For Heating Points And 36 Amcb For Mains. The Job Includes The Cost Of 4 Sq. Mm Multi Stranded Pvc Conductor To Be Laid As Service Line For Lighting System. 45 Providing And Fitting Of 18 Sweep Seiling Fan Of Standard Make Including The Cost Of All Cables , Connections , , Controlsystem Along With The Speed Regulator With Control Switches For The Power Supply 46 Providing And Fitting Of 01 No. Angle Iron / Sheet Metal Board Duly Painted Showing Various Specifications Of The Mechanical And Electrical Equipments Installed At Site. 47 Removal Of Choked Filter Media From 5000 Gph Pressure Filter Vessel. The Job Includes All Loads And Lifts, Disposal Of Choked Media To Dumping Site Outside The Premises Of The Plant Within A Lead Of 5 Km. The Vessel Needs To Be Cleaned Properly And Dried Before Laying Of Fresh Media. 48 Providing And Laying Of Filter Media Of Specific Size And Grade To Be Laid In 5000 / 6000 Gph Pressure Vessel Duly Washed, Free From Dust, Dirt, Loom And Any Other Inorganic Materialor Suspension The Job Includes Carriage Of Filtermedia From Ganderbalto Site Including Allall Loads And Liftsrequired On The Site Condition. The Media Is To Be Lad In Different Layers Of Specific Size And Grade From Bottom To Top Over The Filter Bed Plate. The Bottom Layer Is To Be Laid Without Tilling / Damaging The Pressure Nozzles. 49 Providing And Fitting Of 12 Mm Dia. Fine Threaded Pvc Nozzles Auxiliary Type To Be Fitted On Filter Bed Plate Of Pressure Vessel. 50 Providing And Fitting Of 29 Inch Dia. Rubber Washers / Gaskets For Manhole And Inspection Chamber And Opening Of Pressure Filter Vessel. 51 Providing And Fitting Of 3”X5 / 8” Nuts And Bolts. 52 Providing And Fitting Of Pressure Gauges With Adopters To Replace Damaged Ones These Pressure Gauges Should Be In The Range Of 0-50 Kgf / Cm / Sg Of Reputed Make. 53 Providing, Fabrication And Fitting Of Welded Ms Wire Mesh ( 0.50 Sq. Inch And 1.40Mm Wire Dia. For Bird Screening To The Cgi Pressure Filter House. 54 Carriage Of Cement / Steel / Cgi Sheet / Gi Pipes Below 100Mm Dia And Other Heavy Materials By Mechanicaltransportincluding Loading, Unloadingand Stacking ( Average Distance -25Km )
