Providing, Fixing, Testing And Successful Commissioning Of Air Blower For 2.25Mgd New Water Treatment Plant At Kralpora For Water Supply Scheme Doodhganga.
Tender Value
6.70 Lakhs
Estimated cost
Bid Submission
01 Sep 2022
0 days left
EMD
13400
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kralpora → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Providing, Fixing, Testing And Successful Commissioning Of Air Blower For 2.25Mgd New Water Treatment Plant At Kralpora For Water Supply Scheme Doodhganga.
BOQ
| Sl. No. | Item Description |
| 1 | Providing, fixing, testing and successful commissioning of Air blower ISI mark capable of providing compression 40KLPM @ 0.35-0.40kg/sqm with 40HP/1500 RPM, 3 phase induction electric motor(Kirloskar/ Crompton/Greaves make) complete with auxiliary 150mm dia M.S pipe system upto filter beds. The job includes providing/fixing of M.S fittings; gate vales; pressure gauge meters, nozzles, c-cone block; I section base frame; C.wear block’ non-return valves complete job. specification are as: iBlower type ------…………………. twin lobe –air cooledii.fluid handled ------ …………………airiii. inlet temperature ------……………..ambientiv.discharge pressure-------……………0.35kg/cm²v. differential pressure----- ……………0.35kg/cm²vi.Quantity-------------…………………1 no.vii. Air flow capacity ----------………….2200 m3/hrviii. Inlet pressure-----------………………atmosphereix. Blower speed………………………...1310rpmx.BHP at shaft/duty point…………… ..34.2 BHPxi. Recommended motor………………..40HP/1500RPMxii.Motor frame size/efficiency…………ND200L/IE-2xiii. G02 value ……………………………2.95kg.m²xiv. Noise level at 1.5mtr. Distance………96-98db (A)xv.Type of drive ………….....................V BEL Txvi. Specific gravity ……………………. 1xvii. Inlet pressure ……………. …………Atmosphericxviii.Inlet temperature…………. …………Ambientxix.Outlet temperature …………………. 42°C rise above ambientxx. Inlet & outlet size ……… ... ………..200NMxxi.Lubrication …………………………..Both side oil |
| 2 | Material of construction:i. Cashing, end cover & rotor………… CI FG 260 IS 210ii.Shaft ……………………………….. EN-19 85970iii.Timing Gears…………..………........(20Mn Cr Teeth Hardened & Ground)iv. Side plates, covers & pulley………. CIFG-260, IS 210v.Sealing ………………………………Nitrite rubber/Lip sealvi. Flanges …………………………….. As per BS-100 6392/6418 standardvii.Base frame/silencer………………… MS Fabricated |
| 3 | Arrangement:i.Bearings……………………………. Anti friction (SKF Make)ii. Lubrication …………… ………… Oil grade required shall be XP90/GREESE shallbe AP-3iii.Direction of flow…………………… VERTICALiv.Direction of rotation ……………….. Clockwise from drive end.v. Power Transmission……………….. Through V-Belt. |
| 4 | Providing, fixing, testing and commissioning of 50HP MUG starters (L&T Make) including providing, fitting including making of connections with required size of copper thimbles of standard quality including trench excavation wherever required as per site condition including requisite wiring from starter to motor and main supply as per site requirement. The job includes cost of all fittings and fixtures required for the smooth functioning of the starters to be fixed on frame panel board/walls. The job shall be paid in fitted and fixed form after successful testing and commissioning and is to be carried out as per the directions of site incharge. Complete job. 50Hp/37.5 kw (relay 45-75 Amp) |
| 5 | Providing, installation, testing and commissioning of MCCB Havells/regrind/ L&T make fitted/mounted on wall including making necessary connections, thimbles and requisite wiring from NCCB to main supply and covering the connections with insulating tape to the best satisfaction of site in charge. |
| 6 | Supply, installation testing and commissioning of hand operated geared type chain pully block complete with U-clamps, chains, hooks and other allied fixtures mounted on ISMB 150mm bridge grides installed at site. The job shall also includes fabrication / erection of gantry arrangement such as ( One No. Horizontal I Beam fabricated out of ISMB 150mm about 4.00mt in length) Two No. bearing plates fabricated out of 10mm thick M.S plate; AV size of plates is 300mm x 300mm. Welding ofbearing plates and drilling of four No. holes to each plate for fitment in foundation bolts of 100mm dia M.S pipe columns about 6.00mt in height -2 Nos. one end of the pipe columns is to be grouted in R.C.C block of size 0.50x 0.50 (2 no jobs). The job includes all carriages, skilled labours, tools and tackles along with fabrication of arrangements for fixing /hoisting of gantry arrangements above ground level taking in consideration allprecautions of safety and accidentals during execution of this job at site. The job includes all sorts of carriages; skilled laboures; tools & tackles involved for the job complete.“Test Certificate of manufacturer is Mandatory |
| 7 | Capacity |
| 8 | No. Of chain falls |
| 9 | Mode of Movement |
| 10 | load chain lift |
| 11 | Brand |
| 12 | Mode of Operation |
| 13 | Frame |
| 14 | Gear Wheels |
| 15 | Hand Chain Wheel: |
AI Tender Summary
Tender Timeline
Aug 25, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedSep 01, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 02, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender