|
| 1 | IN DOOR TYPE 7.5 TO 10HP LT Cubical type electrical Panel board Floor/Wall Mounted of welded construction of size 1370mm x 760mm x 460mm fabricated with 16 SWG M.S. sheet with horizontal and vertical intermediate chamber of suitable size on suitable size insulating board to make the Panel Robust, having double door with 14 SWG S.S hinges along with double locking arrangement with arrangement for mounting of switch gear and electrical energy meter i/c powder coating ,Vermin proof having following items. 1. MCCB 63 Amp, 4 Pole-1No. 2. RCCB/ELCB 63 Amp, 4 Pole with earth fault indicator and positive contact indication protecting a circuit automatically 1No 3. Fully automatic star delta starter of 10HP, 3Phase oil immersed type 1No 4. Digital Ampere meter 96mmx96mm square shape of 0-30 Amp range 1No 5. Digital Voltmeter of 96mm x 96 mm square shape of 0–500-volt range with selector switch 1No 6. LED Indicating lamps with fitting (a set of 3 lamps) 1Set 7. Shunt capacitor of 5 KVAR with three phase isolator 1No 8. Motor Protection Assembly having Earth Leakage protection, Phase sequence corrector, Single phasing protection, Over load protection, High voltage-low voltage protection. 1No 9. Programmable time switch (i.e., RYB Phase & facility to change over from automatic to manual & vice versa) up to 10 H.P.1No 10. Complete wiring of panel board & installation of electrical accessories in the panel with required copper conductor wire & thimbling etc. as required. The panel board shall be mounted on the base frame of 600mm height made of 50x50x6mm angle iron frame. Make: -All the insert used in Panel must be of DJB approved makes and should be ISI marked where make of that equipment is not approved. |
| 2 | Supply of kit kat board made out of wooden having 3 Nos. 100 Amp (415 volts re-wireable) kit kat of Havells/Standard/ DJB approved make. |
| 3 | Supply of PVC insulated PVC sheathed, copper flat submersible conductor(flexible) cable, Size 3 core x 6 Sq mm ,1100 Volts, conforming to IS 694 . Make:- Havells/Finolex/DJB approved make |
| 4 | Supply of energy saving & environment friendly, pressure die cast Aluminum housing 45-Watt LED Street luminaries. Make:- Havells/Bajaj/Crompton/DIB approved make |
| 5 | Supply of 50mm dia. B class GI pipe length 3 Mtr. With duly Welded flange in both sides, complete with cutting of flange for cable and welded support in both flanges.Make: - Jindal/ Parkash/ Surya/Tata/Tata/Jindal Hisar/Jindal Gaziabad/ISI |
| 6 | Supply of G.I. tail piece medium class of 0.5 mtrs long including one end flanged and other end threaded of 50mm dia. Make:- Jindal Hisar/Jindal Gaziabad/ISI |
| 7 | Supply of 50mm dia. GI Bend with both side flanges duly welded. Make Jindal Hisar/Jindal Gaziabad/ISI/ DJB approved make. |
| 8 | Pressure Gauge of 150mm dia. size having required range with accessories such as GI fittings, Bib cock etc. required complete the work. Make:-Hguru/fibeg/DJB approved make. |
| 9 | Supply of M.S. Clamp of MS strip duly hole for holding the pipe of 50mm dia. with nut bolts and washer. |
| 10 | Supply of M.S. Bore cover made out of MS plate suitable for 12” dia. bore complete with suitable hole for passing the 50mm dia. GI Pipe |
| 11 | Supply of Nut Bolts,Washer,Spring of sizes as per site requirement. |
| 12 | Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. (DSR E&M 2018 item no. 5.2) |
| 13 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm. (DSR E&M 2018 item no. 5.9) |
| 14 | Workmanship Charges for lowering the submersible pump set one no. in bore well, Fixing/Erection/Installation of E&M equipments, accessories, testing and commissioning on load with satisfactory functioning of Pump. The work includes all sundry required items for completion of work, i.e. eccentric taper, rubber gasket, necessary reinforcement and vibration isolation arrangement, etc. and loading, unloading, cartage, making good all damages caused during installation and restoring the same to their original finish as required, adequate safety provision, barricading, warning signal and other safety measures while executing the work or wherever necessary so as to avoid accident. The components of the installation shall be of such design so as to satisfactory function under all conditions. The all-sundry items which are useful & necessary for operation of Tube well shall be deemed to have been included, such items are especially in specification as per site requirement. |
