Upgradation Of Chemical Technology Lab ( Lab Furniture ) -Modular Laboratory Table With Two Storage Cabinets And Granite Top. Overall Dimensions: 1200Mm Length X 750Mm Depth X 900Mm Height ( Including Granite And Bottom Frame ) Table Shall Consist O, palampur-Himachal Pradesh

Upgradation Of Chemical Technology Lab ( Lab Furniture ) -Modular Laboratory Table With Two Storage Cabinets And Granite Top. Overall Dimensions: 1200Mm Length X 750Mm Depth X 900Mm Height ( Including Granite And Bottom Frame ) Table Shall Consist Of Two Storage Cabinets And Granite Top.The Size Of Storage Cabinet Shall Be 600Mm Length X 530Mm Depth X 686Mm Height ( Without Bottom Frame ) . Each Storage Cabinet Should Be Provided With One Drawer And Below It Twin Shutters. Top Of The Table Shall Be 17 ( + / - 1Mm ) Black Granite Supported Underneath With 9Mm Thick Bwr Ply Or 25Mm Wide 3Mm Thick Soft Pad Sheet. V –Groove Should Be Provided In Granite’S Bottom Surface For Dripping Down The Water Or Liquid Through It. Sharp Edges Of The Granite Should Be Chamfered / Rounded Off. All The Gaps Should Be Filled Up Or Covered With Silicon Sealant. All The Edges And Corner Of The Granite Should Be Nicely Polished. The C- Type Floor Mounted Bottom Frame Of The Table Should Be Made Of 1.2Mm Thick Crca Sheet And 188Mm High X 480 Mm Depth Including Nylon Level Adjusters. The Body Of The Storage Cabinets Should Be Made Out Of 0.8Mm Thick Crca Sheet. Drawer’S Front Fascia And Shutters Should Be 15Mm Thick With Square Edges And Should Be Made Of Crca Sheet And Also Having Sandwiched Or Double Skinned Construction. The Drawer And Shutter Outer Wall Should Be Made Of 1Mm Thick Crca Sheet And Inner Wall Should Be Made Of 0.8Mm Thick Crca Sheet. Shutters And Drawer’S Front Fascia Should Be Provided With High Quality Rubber Beading Embedded All-Around In Between Outer And Inner Walls So As To Minimize The Noise Level While Opening And Closing The Drawer And Shutters. The Shutters Of The Storage Units Should Be Fixed With Stainless Steel Hydraulic Zero Crank Hinges Only. Hardware Like Screws Should Be Stainless Steel Only For The Fixing Of Hinges, Doors And Drawer.Drawers Should Move On Ball Slide Zinc Coated Telescopic Channels. Handles Of The Shutters And Drawers Should Be Aluminium Recessed . Drawers And Shutters Of Storage Cabinets Shall Be Provided With Locking Facility. All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 2 Modular Laboratory Table With Single Storage & Knee Space.Overall Dimensions: 1200Mm Length X 750Mm Depth X 900Mm Height ( Including Granite Top And Bottom Frame ) Table Shall Consist Of One Storage Cabinets, One Knee Space With Keyboard Trey And Granite Top. The Storage Cabinet Shall Be Of Size600mm Length X 530Mm Depth X 686Mm Height ( Without Bottom Frame ) . Storage Cabinet Should Be Provided With One Drawer And Below It Twin Shutters.The Knee Space Should Be Provided Next To The Storage Cabinet And Shall Be Of Size 600Mm Length X 530Mm Depth. The Knee Space Rear’S Side Should Be Provided With Sheet Metal Cover Of 850Mm Height, Made Of 0.8Mm Thick Crca Sheet. A Metal Keyboard Trey Movable On Telescopic Channel Should Be Provided Along With Knee Space Which Has To Be Fixed Below The Granite Top.Top Of The Table Shall Be 17 ( + / - 1Mm ) Black Granite Supported Underneath With 9Mm Thick Bwr Ply Or 25Mm Wide 3Mm Thick Soft Pad Sheet. V –Groove Should Be Provided In Granite’S Bottom Surface For Dripping Down The Water Or Liquid Through It. Sharp Edges Of The Granite Should Be Chamfered / Rounded Off. All The Gaps Should Be Filled Up Or Covered With Silicon Sealant. All The Edges And Corner Of The Granite Should Be Nicely Polished.The C- Type Floor Mounted Bottom Frame Of The Table Below Cabinet Should Be Made Of 1.2Mm Thick Crca Sheet And 188Mm High X 480 Mm Depth Including Nylon Level Adjusters. The Body Of The Storage Cabinets Should Be Made Out Of 0.8Mm Thick Crca Sheet. Drawer’S Front Fascia And Shutters Should Be 15Mm Thick With Square Edges And Should Be Made Of Crca Sheet And Also Having Sandwiched Or Double Skinned Construction. The Drawer And Shutter Outer Wall Should Be Made Of 1Mm Thick Crca Sheet And Inner Wall Should Be Made Of 0.8Mm Thick Crca Sheet. Shutters And Drawer’S Front Fascia Should Be Provided With High Quality Rubber Beading Embedded All-Around In Between Outer And Inner Walls So As To Minimize The Noise Level While Opening And Closing The Drawer And Shutters. The Shutters Of The Storage Units Should Be Fixed With Stainless Steel Hydraulic Zero Crank Hinges Only. Hardware Like Screws Should Be Stainless Steel Only For The Fixing Of Hinges, Doors And Drawer.Drawers Should Move On Ball Slide Zinc Coated Telescopic Channels. Handles Of The Shutters And Drawers Should Be Aluminium Recessed . Drawers And Shutters Of Storage Cabinets Shall Be Provided With Locking Facility. All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 3 Modular Laboratory Table With Sink & Tapoverall Dimensions: 900Mm Length X 750Mm Depth X 900Mm Height ( Including Granite And Bottom Frame ) The Modular Lab Sink Table Consist Of A Bottom Cabinet With Twin Shutters, Pp Sink Basin With Waste Pipe, A Bench Mounted 3-Way Goose Neck Tap And Granite Top.The Bottom Cabinet Shall Be Of Size 900Mm Length X 530Mm Depth X 686Mm Height ( Without Bottom Frame ) . The Bottom Cabinet Should Be Provided With Twin Shutters. Top Of The Sink Unit Shall Be 17 ( + / - 1Mm ) Black Granite Supported Underneath With 9Mm Thick Bwr Ply Or 25Mm Wide 3Mm Thick Soft Pad Sheet. V –Groove Should Be Provided In Granite’S Bottom Surface For Dripping Down The Water Or Liquid Through It. Sharp Edges Of The Granite Should Be Chamfered / Rounded Off. The Gaps Should Be Filled Up Or Covered With Silicon Sealant.All The Edges And Corner Of The Granite Should Be Nicely Polished.The C- Type Floor Mounted Bottom Frame Of The Sink Unit Should Be Made Of 1.2Mm Thick Crca Sheet And 188Mm High X 480 Mm Depth Including Nylon Level Adjusters. The Body Of The Bottom Cabinet Should Be Made Out Of 0.8Mm Thick Crca Sheet. Shutters Should Be 15Mm Thick With Square Edges And Should Be Made Of Crca Sheet And Also Having Sandwiched Or Double Skinned Construction. The Shutter Outer Wall Should Be Made Of 1Mm Thick Crca Sheet And Inner Wall Should Be Made Of 0.8Mm Thick Crca Sheet. Shutters Should Be Provided With High Quality Rubber Beading Embedded All-Around In Between Outer And Inner Walls So As To Minimize The Noise Level While Opening And Closing The Shutters.The Shutters Of The Bottom Unit Should Be Fixed With Stainless Steel Hydraulic Zero Crank Hinges Only. Hardware Like Screws Should Be Stainless Steel Only For The Fixing Of Hinges, Doors. Handles Of The Shutters Should Be Aluminium Recessed.All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 4 Modular Laboratory Corner Table Overall Dimensions: 900Mm Length X 900Mm Depth X 900Mm Height ( Including Granite And Bottom Frame ) The Corner Table Shall Consist Of One Storage Cabinets And Granite Top.The Corner Storage Cabinet Shall Be Of Size700mm Length X 700Mm Depth X 686Mm Height ( Without Bottom Frame ) . Corner Storage Cabinet Should Be Provided With Single Shutter, And One Horizontal Rack.Top Of The Table Shall Be 17 ( + / - 1Mm ) Black Granite Supported Underneath With 9Mm Thick Bwr Ply Or 25Mm Wide 3Mm Thick Soft Pad Sheet. V –Groove Should Be Provided In Granite’S Bottom Surface For Dripping Down The Water Or Liquid Through It. Sharp Edges Of The Granite Should Be Chamfered / Rounded Off. All The Gaps Should Be Filled Up Or Covered With Silicon Sealant. All The Edges And Corner Of The Granite Should Be Nicely Polished.The C- Type Floor Mounted Bottom Frame Of The Table Should Be Made Of 1.2Mm Thick Crca Sheet And 188Mm High Including Nylon Level Adjusters.The Body Of The Storage Cabinets Of Corner Table Should Be Made Out Of 0.8Mm Thick Crca Sheet. Door Should Be Made Of 1Mm Thick Crca Sheet. Shutter Should Be Provided With A Knob For Closing And Opening. All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 5 Modular Laboratory Two-Tier Reagent Rack Overall Dimensions: 1200Mm Length X 200Mm Depth X 900Mm Heightthe Two Tier Reagent Rack Consists Of Two Vertical Supports, Two Shelves, Electrical Duct And Switch-Sockets. Vertical Support Should Be Of Size 900Mm Height X 200Mm Depth X 50Mm Wide. The Vertical Supports Should Have Sandwiched Or Double Skinned Construction. The Inner And Out Wall Of Vertical Supports Should Be Made Of 1Mm Thick Crca Sheet. Reagent Rack Should Have Two Shelves Of 1100Mm Length X200mm Width X 8Mm Deep. The Shelves Should Be Made Of 1Mm Thick Crca Sheet.The Electrical Duct Of 1100Mm Length X 200Mm Width X100mm Height Should Be Provided Below The Second Shelf Of The Rack. The Shelf Should Be Made Of 1Mm Thick Crca Sheet.The Electrical Duct Should Have 2Nos Six-Module Electrical Plate Having 2Nos 6 / 16 Amp Socket And 2Nos 16 Amp Switch And 4 Sqm Electrical Copper Wires. All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 6 Modular Half Trapezoid Electrical Duct With Switch And Socketsoverall Dimensions: 1200Mm Length X 100Mm Depth X 90 Mm Heightelectrical Duct Consists Of Base And Top Cover, Electrical Wiring, Six Module Electrical Plate With Switch And Sockets. Electrical Duct’S Base And Removable Top Cover Should Be Made Of 0.8Mm Thick Crca Sheet. The Electrical Duct Should Have 2Nos Six-Module Electrical Plate Having 2Nos 6 / 16 Amp Socket And 2Nos 16 Amp Switch.Trapezoid Electrical Duct Should Be Provided With Electrical Wiring 4.00 Mm Square Mm And Earthing Wire 1Square Mm. All The Crca Components Are Pre-Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200 Deg. C To Provide Scratch Resistance Surface Coating Film Of Thickness 50-60 Microns. 7 Chemical Storage Cabinet With Toughned Glass Door Overall Size:- Height 1980 Mms, Width 900 Mms, Depth 485 ( + / -10Mm ) The Chemical Storage Cabinet Should Be Made Of Gpsp Sheet Of Uniform Thickness Of 0.8Mm For The Body And Shelves, 1.2 Mm For Doors Frame Duly Cut And Bends With The Help Cnc Machines. Cabinet Should Have 2 Back Sheets And Internal Sheetis Provided With Perforations. Top Is Provided With Cutout Of Dia 100Mm For Exhaust Of Fume. The Doors Should Be Provided With 4Mm Thick Toughened Glass Having High Quality Rubber Beading On All Four Sides And Further Holding With Sheet Metal Strips. Welding On The Front Frame Of The Doors Should Not Be Acceptable. The Doors Are Provided With 3 Way Bolting System. The Top And Bottom End Of The Locking Rod Should Be Horizontally Hook Type And To Be Inserted Into The Horizontal Slot And 3-Way Lock Should Be Operated By Single Key. The Chemical Storage Cabinet Shall Be Equipped With Four Adjustable Perforated Shelves Thereby Making 5 Compartments. The Steel Shelf Shall Be Capable Of Carrying A Uniformly Distributed Load Of 70 Kgms. The Cabinet Shall Be Provided With Three Hinges For Each Door Having Removable Hinge Pins. All The Steel Component Should Be Pre- Treated For De-Greasing, De-Rusting And Phosphating. After Proper Pre-Treatment, The Steel Components Should Be Epoxy Powder Coated And Oven Baked At Temp. Above 200-Degree C To Provide Scratch Resistance Surface Film Thickness 50-60 Microns.

INR 500 /-

INR 20000.0 /-

INR 9.97 Lakhs /-