Haryana Rural Roads Development Agency has published Upgradation Of Chilkani Dhab To Kuttabarh Via Mehna Khera Road Under Pmgs Y Iii Batch Iii. Submission Date for this Tender is 30-08-2022. Road Work Tenders in sirsa Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Clearing and Grubbing road land including uprootingvegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, to all lead and lifts. Including removal and disposal of top organic soil not exceeding 150mm in thickness by mechanical means as per clause no. 201 of MoRD specification Rural roads-2004. |
| 2 | Milling on Bituminous Surface:Dismantling of existing damaged Bitumen surface by cold Milling Machine up to any depth and hauling the milled material up to any leadand stacking at nearest recycling Plant site (HSR 17.43.2)Note- The unutilized quantity of reclaimed bituminous mix material shall be recovery item 34 |
| 3 | Dismantling of flexible pavements and disposal of dismantled materials up to a lead any, stacking serviceable and unserviceable materials separately, as per technical clause 202 of MORT&H specifications. (HSR 17.3) |
| 4 | Excavation for roadwork in soil by manual/mechanical means including cutting , trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including breaking of clods and disposal within ROW as per technical clause 301 of MORT&H specifications.(HSR 17.74) |
| 5 | Earth work in excavation of foundation of structures as per drawing and technical specification,clause 305.1including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter,and disposal with all lead and lift , dressing of side and bottom andbackfilling in trenches with excavated suitable material as per clause no. 305 of MoRD specification Rural roads-2004. |
| 6 | E/Work in embankment , subgrade and Berm in raising portion in RD 445 to 830 to with soil minimumCBR of 8%( 4 days soaked) obtained from borrow pit with all lead and lift transporting to site, spreading, grading to required slope and compacted to meet requirement of section 301 of MoRD specification Clause No. 301.The finished road surface will be as per X-section and L-Section approved by Employer with respect to GTS . At no place, sub grade of raised road will be less than 0.90 mtr above adjoining NSL. NSL for a block of 100mtr will be worked as mean of 6 levels taken on 20 m center to center length of road. These six levels are at three location on both side one at edge row. Other at 5 m and 10 m away from row. In built up area criteria of 0.90 Mtr. High over NSL shall not apply. In case the quantity of earth work calculated with NSL and finished level found to be less than 2916.17 cum. Then actual quantity (less than 2916.17 cum) will be paid. In case quantity worked out to be more than 2916.17 cum, then only 2916.17 cum cum will be paid Excess quantity shall be incidental to work and nothing extra will be paid. Further it shall be ensured that atleast 500mm of subgrade with earth of minimum CBR 8% (4 days soaked) shall be constructed at each location. Whenever any cutting of existing subgrade is required on this account excavation as well as handling and disposal of earthwork to accommodate minimum 500mm thick subgrade of minimum 8% CBR (4days soaked) shall be carried out by the agency at his own cost. Nothing extra will be paid on this account. Before start of work, L- sectionand X section shall be got approved from the employer with respect to GTS as per directive. Note: If soil of CBR 8% is not available then the agency will do appropriate stabilization as per IRC – SP—89-2010 as approved by SE-In-Charge and nothing extra shall be paid on this account and it will be incidental to work. No earth work will be allowed from PWD land |
| 7 | Preparation of berms including filling of Earth work, excavation and cutting of earth in all kind of soils including dressing the bank, side slope to given levels and templates after breaking of clouds, including the cost of rolling and watering all allowances for labour hardness wetness irrespective of all lead and lift and including Compensation for earth taken from private land, fields etc. and compacted to meet requirement of table 300-2 of MoRT&H specification clause No. 30 and to entire satisfaction of the Engineer of the work confirming to PWD specification No. 6.2 and 6.3 and 3.2 and the other specification 1990 Ist edition. As per X-section. This item also includes E/W if required in sub grade for Widening and Shoulder. Earth used for sub grade, shoulder and berms should have minimum CBR 8%. Note:- No earth work will be allowed to be taken from PWD B&R/ROW except for surplus earth after approval from Engineer. |
| 8 | Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (HSR 17.5.3) |
| 9 | Providing laying, watering and compacting of 200 mm GRANULAR SUB BASECOARSE (G-III) graded by providing well graded material spreading in uniform layers with mortar grader on prepared surface mixing in a mechanical mix plant at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification of MoRD clause 401for Rural Roads 2004). Note:- Only crushed material should be used, no local earth/sand shall be used.The material finer than 425 micron shall have zero plasticity index (P-I) 2. Material and operation manufacturing shall be approved by Engineer. |
| 10 | Construction of Bio enzyme based soil stabilised layer to a required thickness 100 mm as per manufacturer design with ripping the existing crust 50 mm and adding 50mm of borrow soil with local soil material/gravel/murram, having minimum CBR 8% and treating it with TerraZyme in the ratio 1 Litre for 15 cum soil, spreading in uniform layer with tractor grader on prepared surface. Mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical specification incl all labour, materials, like soil and metal, equipment’s etc., complete.As per the directions of the Engineer incharge of the work. Note:-the work to be executed in the presence of representative of technology provider |
| 11 | Providing & laying 75/225 mm thick (Compacted) stone metal (G-II) 53mm to 22.4mm gauge wearing coat to water bound macadam in layer of 75mm eachusing screening type ‘B’ compacting with three wheeled power rollers of 80-100 kN capacity or tandem or vibratory of 80-100 kN static weigth to achieve the desire density including lighting, guarding barricading and maintenance of diversion etc. as perclause no 405 of MoRD specification for Rural Roads-2004) as per drawing and design directed by the Engineer complete in all respects.(N.S.) Note: - 1.Only crushed stone metal material should be used. No local earth/ natural occurring sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer. |
| 12 | Providing and applying primer coat with bitumen emulsion (SS-I) on prepared surface of granular base including cleaning of road surface and spraying primer mix including silane at the rate of 0.60 kg/sqm using mechanical means asper Technical specification clause 502 of MoRD specification Rural roads-2004. Instructions issued from time to time by MoRD regarding bitumen emulsion will be followed strictly. Note:- Bituminous Macadam to be laid with in 24 Hrs. of laying primer coat & Tack coat does not required to be provided above the primer coat. However, if the BM is not laid with in 24 hours of laying prime coat then tack coat would have to be provided by the contractor but no payment at the same shall be made and it would be incidental to work. |
| 13 | Providing and applyingTack coat of VG 10 ( 80/100 grade) bitumen using bitumen @ 0.25 kg per sqmall inclusive including clearing and blowing dust off the surface using a compressor and brooms ( conforming to clause 503 of MoRD specification-2004) for PC.Instructions issued from time to time by MoRD regarding bitumen VG-10 will be followed strictly. |
| 14 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of crushed stone aggregates of specified grading premixed in a continuous Drum type of hot mix plant of appropriate capacity not less not less than75 tonne per hour, with bituminous binder VG - 10 @ 1.46 kg per sqm, laid with Paver Finisher Mechanical androlling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications. (Based on HSR 17.33.1) Note: - Before carrying out bituminous work, coating & stripping of bitumen aggregate mix is to be performed in accordance with IS – 6241. If coating and stripping of bitumen aggregate mix is less than 95%, anti-stripping agent will be used by contractor. The anti – stripping agent should conform to the requirement as stipulated in IS 14982:2017. The cost so incurred will be considered as incidental to work and nothing extra shall be payable. The type and brand of anti-stripping agent along with procedure shall be approved by SE-in-charge in writing before start of work. A proper record of results be maintained and same shall be submitted along with bills by the contractor. |
| 15 | Providing and laying ‘B’ type seal coat with VG-10 grade bitumen @ 0.68 kg per sqm of road excluding cost of tack coat, with mixed material brought from Hot mix plant and laying with paver finisher and compacting with road roller to achieve specified/desirable value of compaction as per direction of Engineer including cost of lighting arrangement, sign board and night watch, complete in all respect as per clause 510 of MoRD specification for rural roads 2004. |
| 16 | Providing and Laying 80 mm thick ISI marked Interlocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. (HSR 17.69.2) |
| 17 | Providing and laying of cement concrete blocks of size 0.450 m x0.300 m x 0.15 m of cement concrete (C.C) M30 grade and spreading 25 mm thick sand underneath filling joints with sand on existing W.B.M./G.S.B base as per technical specification clause 1503 (HSR.17.66.1) |
| 18 | Providing & fixing Reinforced cement concrete M-25 grade precast 5th kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.1) |
| 19 | Providing & fixing Reinforced cement concrete M-25 grade precast ordinary kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.2) |
| 20 | Providing & fixing Reinforced cement concrete M-25 grade 200 meter stone of standard design as per IRC:8- 1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.4) |
| 21 | Reinforced cement concrete M15 grade boundary pillar of standard design as per IRC:25-1967, fixed in position including finishing and lettering but excluding painting (HSR 34.28). |
| 22 | Providing and fixing of typical PMGSY informatory sign board with logo as per MoRD specification and drawing.Three MS plates of 1.6mm thick, top and middle plate duly welded with S flat iron 25mmX5mm size on back on edges,25mmX25mmX5mm. The angle iron frame of the lower most plate and flat iron frme of middle plate will be welded to 2 nos,.75mmX75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmX450mmX600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmX47mm of 12 SWG steel plate tube . All MS will be stove enamelded on both sides. Lettering and printing arrows, border etc. will painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.0. |
| 23 | Providing and fixing of typical PMGSY Maintenance sign board with logo as per MoRD specification and drawing.Three MS plates of 1.6mm thick, top and middle plate duly welded with S flat iron 25mmX5mm size on back on edges,25mmX25mmX5mm. The angle iron frame of the lower most plate and flat iron frme of middle plate will be welded to 2 nos,.75mmX75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmX450mmX600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmX47mm of 12 SWG steel plate tube . All MS will be stove enamelded on both sides. Lettering and printing arrows, border etc. will painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.0. |
| 24 | Providing and fixing Logo Board of PMGSY size 600×600mm diamond shape with 1 plate of size 900×250 mm made of 60 gauge sheet over frame of angle iron 25×5×3 as per PMGSY specifications & drawing, painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 25 | Providing and fixing Citizen Informatory Sign Board of PMGSY size 600×600mm diamond shape with 1 plate of size 900×250 mm made of 60 gauge sheet over frame of angle iron 25×5×3 as per PMGSY specifications & drawing, painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 26 | Providing & fixing overhead sign board 3050x1525mm cantilever type single sided using retro reflectiveSheetingTypeXI asperASTMD495609 and as per IRC67-2012 with retro reflectiveSheeting asper ASTM D 4956 – 09 and as per IRC 67 – 2012 fixed over 4mm thick Aluminium Composite Material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sidedandfixingthesamewithsuitablesizealuminium alloyrivets@200mmc/ctobacksupportframeof 40x40x6mm angle iron supported on designed single supportsystemofMSpipeandplatesintheformofa cantilevertypetrussmadewith350NBpipe@50kgper metre as vertical support, 50NB pipe @ 4.50kg per metre and 40NB pipe@ 3.61kg per metre for truss including base plates,gussetplates, designed RCC foundation for fixing in ground complete as per clause 802 of MORT&H specifications.Suppliershallprovideawarrantyasper clause 6.9 of IRC 67-2012 for retro reflective sheeting& a certifiedcopyoftestreportsfromanindependenttest laboratory including three year outdoor weathering test report for sheeting tested in India conditionconforming to clause 6.7 of IRC 67-2012. |
| 27 | Providing & fixing cautionary sign boardas per IRC 67- 2012 with using retro reflective Sheeting Class B as per ASTM D 4956 09 and as per IRC 67 2012 fixed over 3mm to 4mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.75m for vertical post complete as per clause 801 of MORT&H specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports including three year outdoor weathering test report for sheeting tested in India condition from an independent test laboratory conforming to clause 6.7 of IRC67-2012 (i) 600 x600x600mm TRIANGLE(HSR 34.5.2) |
| 28 | 600 mm Circular (HSR 34.7.2) |
| 29 | 600 mm x 450 mm rectangular (HSR 34.9.2) |
| 30 | 900 mm HIGH OCTAGON |
| 31 | Providing & Marking center line / side line 2.5mm thick (minimum) with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including Reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. Note: - Before start of work the contractor shall give brand, batch number, manufacturing date of the material to be used along with a photocopy of bill duly signed by the contractor and get approved the same from Engineer-In-Charge before use. (Based on HSR.34.26) |
| 32 | Plain cement concrete 1 :3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per clause 2100 of MORT&H specifications. (HSR 15.5) |
| 33 | Plain Cement Concrete grade M-15 in Open Foundation complete as per Drawing and Technical 1500, 1700 and 2000 of MORT&H Specifications.(HSR 15.8.1) |
| 34 | Plain cement concrete grade M-15 in sub-structure complete as per drawing and MORT&HMoRT&H Specifications 1500,1700 and 2200 (HSR 27.5) |
| 35 | Reinforced Cement Concrete grade M-20 in Open Foundation complete as per Drawing and Technical 1500, 1700 and 2000 of MORT&H Specifications.(HSR 15.8.3.1) |
| 36 | Reinforcedcement concrete grade M-20 in sub-structure complete as per drawing and MORT&HMoRT&H Specifications 1500,1700 and 2200 (HSR 27.9.1.1) |
| 37 | Furnishing and Placing Reinforced cement concrete grade M-25 in super-structure as per drawing and MoRT&H clause 1500, 1600 and 1700 of MORT&H Specification (HSR.27.27.1.1) |
| 38 | Brick work with common burnt clay non modular bricks of class designation 10.5 in foundation and plinth in cement Mortar 1:4. (HSR 7.21.1) |
| 39 | 12mm thick Plastering with cement mortar (1:3) on brick work in sub-structure as per Technical Specifications (HSR 11.5.2) |
| 40 | Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level. Note: - Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 6.33.6) |
| 41 | Providing and laying 600mm dia reinforced cement concrete pipe NP-4 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1 :2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapetsas per clause 2900 of MORT&H specifications Note: - Contractor shall supply bill of manufacture of pipes. Pipes should bear name of manufacturer and ISI mark along with bill duly valid ISI certificate of manufacturer should be supply. Without these bills certificate no payment shall be released. (HSR.17.61.1) |
| 42 | Back filling behind abutment, wing wall and return wall with Granular material complete as per drawing and MoRT&H Specification (HSR 27.16.1) |
| 43 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1 V:20H towards drawing force. Complete as per drawing and MoRT&H Specifications (HSR.27.15) |
| 44 | Recovery Items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have beencalculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the pricequoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under:- (i) Bituminous Milling Material @ Rs.1711/- Per Cum |
| 45 | Granular material @Rs.450/-per Cum Note:- All quantities of the above materials have been worked out on the basis of theoritical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual sacrifying is found no lesser side , no claim of agency on this score will be entertained and full recovery on the basis of quoted rates and quantity exhibited in the entertained and full recovery on the basis of quoted rates and quantity exhibited in the BOQ shall be made . The reserve rates are minimum rates to be used as base for quoting purchase rates by the agency . No rates below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price.Note:- If any discrepancy found in the unit/Nomenclature in the items of BOQ. The nomenclature of HSR/MoRD shall be applicable. Note:- If any discrepancy found in the unit/Nomenclature in the items of BOQ. The nomenclature of HSR/MoRD shall be applicable.NOTE- It may kindly be noted that the contractor would be obligated to carry out 05 years paid maintenance as per the rates fixed in the DNIT. However, the items of 05 years maintenance shall not be part of BOQ to avoid any confusion. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
