Strengthening Of Existing School And Drinking Water ( Up To Class Viii ) At Gps Nayapura Maholi Karauli S
Tender Value
21.33 Lakhs
Estimated cost
Bid Submission
23 Aug 2022
0 days left
EMD
42660
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
maholi → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Strengthening Of Existing School And Drinking Water ( Up To Class Viii ) At Gps Nayapura Maholi Karauli S
BOQ
| Sl. No. | Item Description |
| 1 | PART A CIVIL WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils |
| 3 | PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 Coarse sand :8 graded stone aggregate 40 mm nominal size). |
| 4 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in cement mortat 1:6 (1-Cement: 6- Sand) |
| 5 | P/L Chequered precast cement concretetiles22mm thick in footpath and courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. completelaid on 20 mm thick bed of C.M 1:4 ( 1 cement: 4 course sand)light shed using shade cement. |
| 6 | Providing and laying in position specified grade ofcement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix PLINTH BEAM/footing |
| 7 | Supply & stacking good earth at site complete including loading , unloading and transportation etc &Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and lift upto 1.5 Mtr. |
| 8 | Brick work with clay flyash F.P.S. brick of class designation 75 in superstructureaboveplinth level upto floor five level in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 9 | Stone Kharanja: Random rubble dry stone kharanja under floor |
| 10 | Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix |
| 11 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement:3 coarse sand) and making good the joints and cost of plastisers (if required ) excluding the cost of centtering shuttering and reinforcement for walls (any thickness) including attached plasters, buttreses, plinth and sring courses, fillets, columns, pillers, piers, abutments, post and struts etc Add Extrafor M 25 grade concrete by using min 410sand mort kg of cenent per cum instead of M 20 grade design mix |
| 12 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. |
| 13 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for foundation, footings, strap beam, raft, base of column etc |
| 14 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for columns, pillers, posts,and struts etc |
| 15 | P/F reinforcement for RCC work including straightening,cutting, bending, placing in position and binding (including cost of binding wire)all complete upto floor five leveTMT bars (Conforming of relevent IS Code). |
| 16 | Half brick msonary in superstructure above plinth level uoto floor V level using F P S bricks of designation 75 in cement mortar 1:4 |
| 17 | Providing and fixing M.S. sheet 1mm thickdouble leaf door shutter windows in angle iron frame35x35x5 mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 18 | Glazed Window : Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13 x 3 mm , 10cm long embeded in cement concrete block 15 x 10 x 10 cm of 1:3:6(1 cement: 3 Course sand : 6 gradred stoneaggregate 20mm nominal size )or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4 mm thick with copper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer , excluding cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : Partly fixed and partly openable ( fixed area not to exceed 33% ) |
| 19 | Wire Gauge Supplying & fixing fixed wire Gauge to the Metal frame of rolled section by metal beading 20X3mm with suitable screw at not exceeding 150mm distance. 14 mesh X 24 Gauge |
| 20 | Guard Bars: Providing and fixing square bars or other flat welded to window/ventilators etc., Guard bar 12 x12mm |
| 21 | kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 Course sand ) for area 2001 to 5000 sq. Cm |
| 22 | kota stone slabs 25 mm thick in risers and stepsskirting, dado and pillars laid on 12 mm (average)thick cement mortar 1:3(1 cement: 3 Course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs , including rubbing and polishing completeFor areaof each slab upto2001 sq. Cm |
| 23 | Internal Plaster : Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish: 12mm thick |
| 24 | External Plaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick |
| 25 | Plaster(Ceiling): 6 mm thick cement plaster to ceiling of mix 1:3(1 cement: 3 fine sand) |
| 26 | Grading roof for water proofing treatment withwater proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 27 | Gola Providing gola 75mm x 75mm in cement concrete 1:2:4(1 cement: 2 coarse sand: 4 stoneaggregate 10 mm and down gauge) including finished with cement mortar 1:3(1 cement: 2 fine sand) as per standard design. |
| 28 | Distempering with dry distemper of approved brand and shade (two or more coats) and of required shade on new work, over and including, priming coat of whiting to give an even shade including all scaffolding. |
| 29 | Exterior finishing :- Finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. New work (two or more coat applied @1.67/ ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm.) |
| 30 | PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). |
| 31 | Copping: Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, copping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M20 grade nominal Mix 1:1.5:3(1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) |
| 32 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia |
| 33 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Bend 87.5110mm dia |
| 34 | Pipe Clip110 mm dia |
| 35 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. |
| 36 | Providing and fixing in CM 1:4 double paitam (rebated) stone door window and ventilator frames of approved quarry. Size 100X75 mm |
| 37 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 38 | Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering- all work upto plinth level 1:2:4(1 cement:2coarse send:4 graded stone aggregate 20 mm nominal size. |
| 39 | Providing and fixing 40 to 50 mm thick sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens (Karries and battens to be paid separately) including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 sand) complete |
| 40 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in charge in skiriting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. |
| 41 | Construction of tube-well from ground levels and upto 100 Meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS:4097-1967 and packing as per IS:2800 (Part I -& II) 1979 as amended upto date (the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes, with supply and wrapping of coir-rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water). 200mm –do-. |
| 42 | Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casingpipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe:200 mm –do- |
| 43 | Development of tube well as per ISI specification using suitable compressor to give free water for required yield of the gravel packed tube well. |
| 44 | Supply fo ERW M.S. black casing pipe ISI marked ( IS : 4270/1992) of grade Fe410 of following sizes at site of work. Nominal bore of pipe (mm) 200 |
| 45 | Testing verticality of tube well by plumbing system and yield test and draw test by pumping system as per IS : 2800 (Part II) 1979. |
| 46 | S & F tube well cover fo M.S. sheet (6mm thick) with nuts and bolts complete forsize. 200 MM |
| 47 | S & F M.S. Clamp, set of 50 X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 48 | Providing & Fixing of HDPE pipe ISI mark (IS:4984/2016 ) for water supply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . for vertical installation 40 mm OD6 kg / cm2 |
| 49 | Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. |
| 50 | 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM |
| 51 | Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Worksconfirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required.OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections.For additional technical parameters of products/ work, referAnnexure \"A\" attached with this BSR . 4.0 Sq.mm 3 core flat / Round |
| 52 | Providing & Laying of synthetic rope for submersible pump ISI marked (IS:5175) of following sizes. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . 20mm (suitable for 90 mm OD pipe) |
| 53 | Supply Installation testing & Commissioning ofISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .For single phase Submersible / Monoblockpump 2.0 HP to 3.0 HP (DOL starter) |
| 54 | Constructionof 185 cm. dia platform as per approved design and drawing of UNICEF. |
| 55 | Supply & Fixing control panel switch board suiteble for operation upto 3.0 HPsubmersible pump set complete with following accessories & markes. 1. L & T or equivalent make with star dulta connections with Essma make Ammeter & Volt meter.2. Single Phase.3. MCB for CVR Phase lath wiring.4. Iron plat isolator 60/63 amp.5. Fixing of accessories on bakelite 6 mm sheet and all to be fixed as well with brackets nuts and bolts complete inall respect as per direction of engineer in charge. |
| 56 | PART B SANITARY WORK |
| 57 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 lit capacity |
| 58 | P & F G.I. pipes (External Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: b()Concealed pipe in wall including painting with anticorrosive bitumen paint15 mm dia nominal boreB Class |
| 59 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Brass 400 grm,15mm nominal bore. |
| 60 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 15mm nominal bore. |
| 61 | PART C ELECTRIC WORK |
| 62 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copperconductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulatedunsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit &it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick HotDipped Galvanized Modular Box with earth terminal, 10A Modularswitch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3way connector, screws, making connections, testing etc. as required.For specification of copper Conductor, Phenolic Laminated sheet\"s &Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 Foradditional technical parameters of product / work refer Annexure \"A\"attached with this BSR |
| 63 | Short point (up to 3 mtr.) |
| 64 | Medium point (up to 6 mtr.) |
| 65 | Long point (up to 10 mtr.) |
| 66 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper earth conductor 1.1 kV grade(IS:694) in recessed ISI markedMMS ( IS:9537 P - III ) PVC conduit & it\"s ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thickwith earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket,Modular face plate with grid plate, screws, making connections, testingetc. as required. For specification of copper Conductor, PhenolicLaminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E- 05 & E - 07 For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR On board |
| 67 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P -III ) PVC conduit along with ISI marked (IS:3419-1988) accessories asrequired in recess including cutting the wall, covering conduit andmaking good the same as required. For additional technical parametersof product / work refer Annexure \"A\" attached with this BSR 25 mm |
| 68 | Supplying and drawing FR PVC insulated & unsheathed flexible copperconductor as per PWD specification for electrical Works with ISImarked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire shouldbe made from 99.90 % purity copper, class 5 stranding in acc. toIS:8130/IEC 60228 for lower watt loss , oxygen free for less chances ofoxidization, insulation PVC type A/C/D , flame retardant as per IS10810-53, better amperage rating as per IS:3961 part 5, in existingsurface or recessed PVC/ MS conduit/casing capping makingconnections with Copper Lugs of suitable size, Ferrules,testing etc. asrequired. OEM Must have its own in house NABL lab setup for alltesting facilities for wires. For additional technical parameters ofproduct / work refer Annexure \"A\" attached with this BSR |
| 69 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 70 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10kA breaking capacity (B/ C/D tripping characteristic as per type ofload and site requirement) 4 KV impulse withstand voltage, ISImarked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3as per IEC, minimum phase termination capacity of 35sq.mm. ,conductor line load reversibility , IP 20 contact protection and fittedin existing distribution board/sheets, minimum electrical operation20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A &above rating including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab typetest reports & All as per pre approved by Engineer in charge. Foradditional technical parameters of product / work refer Annexure\"A\" attached with this BSR Single pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating |
| 71 | Providing & Fixing of Recessed/surface mounting heavy dutyhorizontal type Double Door ( Metal / Glazed )Distribution boardwith Metal end box made out from Galvanized steel / CRCA sheetnot less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC61439- 1 & 3, powder painted complete with reversible door (fordouble door DB only )100 amp. insulated copper bus bar/shortinglink , copper neutral link, copper earth link , color codedinterconnecting wire set of suitable rating and din bar,maskingsheet, making internal DB terminations with copper lugs, Ferrules,detachable gland plate, including making connections, testing etc.as required. OEM shall have submit NABL / CPRI / ERDA accrediatedlab type test reports & All as per pre approved by Engineer incharge. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box 6 Way (6+2 |
| 72 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture madefrom Powder coated Extruded aluminium housing with in builtdriver, System lumenefficacy = 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuitprotection ,THD < 10% , P. F.=0.95, CRI >80 , life time of minimum 50000 Burning Hourswith , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more thanthe specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.).Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. OEMmust have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 &LM80) certificate / Report from OEM shall be submitted. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 73 | Supply and laying PVC Insulated and PVC Round Sheathed Multi Corecopper conductor (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.90 % purity copper, stranding in acc. toIS:8130/IEC 60228 for lower watt loss , oxygen free for less chances ofoxidization, insulation PVC type A/C/D , flame retardant as per IS10810-53, better amperage rating as per IS:3961 part 5, in existingpipe / open trench / Cable tray / on surface including makingconnection etc. as required. For additional technical parameters ofproduct / work refer Annexure \"A\" attached with this BSR 2.5 sq.mm x 3 core |
| 74 | Providing & Fixing of BEE Star rated copper wounded double ballbearing capacitor start, aluminium body & Metallic blade ceiling fanConforming to all the performance requirements laid down in IS374:2019 including all amendments, as applicable ; & Carry BIS licensing(i.e. ISI marking) with down rod up to 80 cm with secondary supportsafety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulatedflexible copper conductor making connection testing etc. as required. Allas per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with thisBSR .1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 75 | Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceilingrose with CM/L no. printed and made out from industrial gradePolycarbonate or fire resistant ABS material, brass terminal & captivescrews including making connection testing etc. as required.All as per preapproved by Engineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR . |
| 76 | Providing & Fixing of ISI marked (IS:1258) batten/angle lamp holder withCM/L no. printed and made out from industrial grade Polycarbonate or fireresistant ABS material, brass terminal & captive screwsincluding makingconnection testing etc. as required. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . |
| 77 | P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer incharge. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR |
| 78 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilizationcategory, 4KV impulse withstand voltage, true contact indication,Red colour dolly / lever shall have single mould covering over allpoles for operation , two position din rail mounting, minimumphase termination capacity of 35sq.mm. IP 20 contact protectionand fitted in existing distribution board / sheet including makingconnections, testing etc. as required. OEM shall have submit NABL/ CPRI / ERDA accrediated lab type test reports & All as per preapproved by Engineer in charge.For additional technical parametersof product / work refer Annexure \"A\" attached with this BSR Double pole isolator |
| 79 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISImarked (IS 11037:1984 ) with CM/L no. printed made out of unbreakableand fire retardant vergin poly carbonate with brass terminals and captivescrews & silver alloy contact tip with IP-20 rating , including all as per preapproved by Engineer in charge,making connections, testing etc. asrequired. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR5 step fan regulator 2 Module 360 dgree rotating |
| 80 | P & F 1.2 mm thick G. I. / M .S. Sheet boxes duly finished with twocoats of red oxide and with earthing terminal of following sizes(nominal size) in recessed/surface as required.For additionaltechnical parameters of product / work refer Annexure \"A\" attachedwith this BSR 1.2 mm thick M. S. Sheet boxes 175mm x 100mm x 60mm |
| 81 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panelwith switchgear selection as per Type-2 Cordinatiom Chart andmade out from 1.6 mm thick powder coated CRCA sheet,enclosure comprising of over load protection relay, short circuit &single phasing protection, Illuminated ON / OFF push buttons,ammeter, voltmeter, indicating lamps etc. suitable for followingrating motors complete in all respect. All as per pre approved byEngineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR . For single phase Submersible /Monoblock pump0.5 HP to 1.5 HP (DOL starter) |
| 82 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %,round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cabletray(with cable tie) including testing etc. as required of following size. OEM musthave it\"s own in house NABL accrediated Laboratory for testing procedure as perIS:10810.For additional technical parameters of product / work refer Annexure\"A\" attached with this BSR 4 core |
AI Tender Summary
Tender Timeline
Aug 12, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedAug 23, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 24, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender