Construction Of 02 ( Two ) Nos. Semi Permanent Pump House, Providing And Installation Of Pump Sets, Providing Fhtc Including Other Allied Works In Different Locations Of Bc Nagar Rd Block Under Dws Sub-Division, Barpathari During 2022-23 ( Gr.-Iv )
Tender Value
55.02 Lakhs
Estimated cost
Bid Submission
31 Aug 2022
0 days left
EMD
1.10 Lakhs
Bank guarantee accepted
Document Fee
4000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
belonia → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 02 ( Two ) Nos. Semi Permanent Pump House, Providing And Installation Of Pump Sets, Providing Fhtc Including Other Allied Works In Different Locations Of Bc Nagar Rd Block Under Dws Sub-Division, Barpathari During 2022-23 ( Gr.-Iv ) .
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.a) All Kinds of Soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cmin depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.A)All kinds of soil |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.a) All work upto plinth livel |
| 5 | i) 1:2:4 ( 1 Cement: 2 fine sand : 4 well burnt brick aggregate 40 mm nominal size) |
| 6 | ii) 1 : 3 : 6 ( 1 cement : 3 fine sand : 6 graded well burnt brickaggregate of 40 mm nominal size) |
| 7 | iii) 1 : 4 : 8 ( 1 cement : 4 fine sand : 8 graded well burnt brickaggregate of 40 mm nominal size) |
| 8 | Centering shuttering including struttings, proppingetc. and removal of form work for: |
| 9 | i) Foundations, footings, bases for columns |
| 10 | ii) Columns, piers, abutments, pillaras, posts and struts |
| 11 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level:i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size |
| 14 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 15 | i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 16 | ii) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank |
| 17 | iii)Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank |
| 18 | iv) Weather shade, Chajjas, corbels etc., including edges. |
| 19 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth Level level i) Thermo-Mechanically Treated bars of gradeFe-500D or more |
| 20 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above Plinthlevel i) Thermo-Mechanically Treated bars of gradeFe-500D or more |
| 21 | First class brick work in foundation and plinth including cost of all materials as required complete: i) In cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 22 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 23 | Extra for brick work in triangular, square and rectangular pillars including cost of all materials as required complete. |
| 24 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:-i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 25 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 26 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. i) Fixed to steel windows by welding. |
| 27 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required i) Using flats 30x6mm for diagonal braces and central cross piece. |
| 28 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.i) Hot finished welded type tubes |
| 29 | Providing and fixing M.S. round holding down bolts withnuts and wahser plates complete as per standard design. |
| 30 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete.i) 40 mm thick |
| 31 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including =cutting to size and shape wherever required.i) 0.63 mm thick Zinc Coating not less 275 Gm/m2 |
| 32 | 12 mm cement plaster of mix.i) In cement mortar 1:4 (1 cement : 4 fine sand) |
| 33 | 15 mm cement plaster on the rough side of single or half brick wall of mixIn Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 34 | 6 mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand) |
| 35 | Neat cement punning. |
| 36 | Distempering with oil bound washabale distemper of approved brand and manufacture and of required shade on new work (two or more coats ), over and including a priming coat of cement primer to give an even shade complete. (Payment shll bemade after submission of Test certificate issued by the manufacturer) |
| 37 | Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.84 kg/10 sqm) |
| 38 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work |
| 39 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 40 | Providing and placing of G.I. pipe over the pump house on top portion of the R.C.C. column as per specification and the direction of the Engineer-in-charge.i) 150 mm dia |
| 41 | Providing and fitting fixing steel sheet enclosed switch fuse unit(suitable for DIN fuses), triple pole with Neutral Link (TPN),415/500 Volt, L & T / Havells / BCH make etc. completeas per specification and direction of the Engineer-in-charge. i) 63 amps |
| 42 | Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge. i) 25 HP/18.5 kw Relay range within 20-32 + 10% |
| 43 | Providing and fitting fixing of 6 feet x 4 feet x 1 inch (thickness) Gamair wood / plywood pannel board for fitting fixing of electrical items, in/c 2 nos MS angle post ( size 2 inch x 2 inchx 9 feet ), nuts & bolts etc. for irrection of the same by1:1.5:3 cement concrete casting (1 feet x 1 feet x 2 feet) below the ground level and paintingtwo ormore coats & plastic paint as per specification and direction of the Engineer-in-charge. |
| 44 | Providing and fitting fixing with PVC insulated single core multistrand Copper cable conforming to IS : 694 for inter connection with all electrical equipments of the pannel board as per specification and direction of the Engineer-in-charge. i) 10 sqmm |
| 45 | Providing and fitting fixing of moving iron type, Range 0-500 V, 96 mm x 96 mm size AC Volt meter ( L & T / AE make) with selector switch as a electrical instrument of the pannel board as per specification and direction of the Engineer-in-charge. |
| 46 | Providing and fitting fixing of moving iron type, Range 0-100/0-200 amps, 96 mm x 96 mm size AC Amps meter direct reading type (L & T/ AE make) with selector switch and CT coil as a electrical instrument of the pannel board as per specification and direction of the Engineer-in-charge. |
| 47 | Providing and fitting fixing of Moulded Case Circuit Breaker (MCCB) of different Thermal release range , 415 + V, 50Hz (L & T, BCH, ABB make) as per specification and direction of the Engineer-in-charge. i) 32-40 Amps |
| 48 | Providing earthing with perforated 40 mm dia G.I. pipe (Medium class) (12 mm dia perforation),laying of 4 mm dia GI wire from earth electrode to panel, including excavating hole of 600 mm dia and refilling with Salt and Charcoal / coke in alternate layers of 300 mm , as per standard specification and direction of the Engineer-in-charge. i) For 3-phase connection with 4.00 mtr. Long G.I. pipe |
| 49 | Providing and fitting fixing3 phase indicating lamp fiited with panel board with three different colour lamps with batten holder completeas per specification and direction of the Engineer-in-charge. |
| 50 | Providing and fitting fixing heavy duty box type (Resin filled) power factor correction capacitorL & T make etc. completeas per specification and direction of the Engineer-in-charge.i) 5-15 kVAr 440 V |
| 51 | Providing and fitting fixing Single phasing preventor +selectable under voltage +selectable over voltage on delay 5 sec & off delay 15 sec phase asymmetry 10% L & T /BCH/HAVELS/Siemens etc. make complete as per specification and direction of the Engineer-in-charge. |
| 52 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cementconforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as perCPWD specification and direction of the Engineer - in - charge.A. Class - 3 ( working pressure 6.0 kg / cm2). |
| 53 | i)40 mm OD |
| 54 | ii) 50 mm OD |
| 55 | iii) 90mm OD |
| 56 | iv)110mm OD |
| 57 | v)140mm OD |
| 58 | Providing, fixing and laying fabricated UPVC bend of required degree conforming to IS : 10124 ( part 8 / 9 / 10 / 11 / 12 / 13 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 59 | i) 40 mm dia |
| 60 | ii) 50 mm dia |
| 61 | iii) 90 mm dia |
| 62 | iv) 110 mm dia |
| 63 | v) 140 mm dia |
| 64 | Providing, fixing and laying fabricated UPVC end cap conforming to IS : 10124 ( Part 4 ) with solvent cementconforming to IS : 14182 including testing of joints complete as perCPWD specification and direction of the Engineer - in - charge. |
| 65 | i)40 mm OD |
| 66 | ii) 50 mm dia |
| 67 | iii) 90 mm dia |
| 68 | iv) 110 mm dia |
| 69 | Providing, fixing and laying fabricated UPVC equal tee conforming to IS : 10124 ( Part 5 ) with solvent cementconforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 70 | i) 40 x 40 mm dia |
| 71 | ii) 50 x 50 mm dia |
| 72 | iii) 90 x 90 mm dia |
| 73 | iv) 110 x 110 mm dia |
| 74 | v) 140 x 140 mm dia |
| 75 | Providing, fixing and laying fabricated UPVC straight reducer conforming to IS : 10124 ( Part 3 ) with solvent cementconforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 76 | i) 50 x 40 mm dia |
| 77 | ii) 110 x 90 mm dia |
| 78 | iii) 140 x 110 mm dia |
| 79 | Providing, fixing and laying flanged fabricated UPVC tailpiecewith MS flange ( 8 mm thick ) conforming to IS : 10124 ( Part6 ) with solvent cement conforming to IS : 14182 including testing of joints complete as er CPWD specification anddirection of the Engineer - in - charge. |
| 80 | i) 90 mm dia |
| 81 | ii) 110 mm dia |
| 82 | iii) 140 mm dia |
| 83 | Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling, cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge.A. External work. i. 15 mmdia. nominalbore |
| 84 | Providing and fixing C.I. non-return valveofapproved quality as perof CPWD specification and direction of the Engineer - in - charge.i) 80 mm nominal bore |
| 85 | Providing and fixing brass ferrule with C.I. cover conforming to IS : 2692 including boring and tapping the main as per CPWD specification and direction of the Engineer - in - charge. i) 15 mm nominal bore |
| 86 | Providing and fixingC.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) as perCPWD specification and direction of the Engineer - in - charge. |
| 87 | i)80 mm dia. A. PN - 1.0 |
| 88 | ii)100 mm dia. A. PN - 1.0 |
| 89 | iii)125 mm dia. A. PN - 1.0 |
| 90 | Providing and laying D.I. specials of class K - 12 suitable for push - on jointing as per IS :9523 as perCPWD specification and direction of the Engineer - in - charge. i Upto 300 mm dia. |
| 91 | Charges for push-on ( Tyton ) joints to centrifugually ( Spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket as perCPWD specification and direction of the Engineer - in - charge. |
| 92 | i) 100 mm dia |
| 93 | ii) 125 mm dia |
| 94 | Providing and laying S & S Centrifugally Cast ( Spun ) Ductile Iron Class K-7 Pipes conforming to IS : 8329 as per CPWD specification and direction of the Engineer - in - charge. |
| 95 | (i) 100 mm dia Ductile Iron Class K-7 pipes. |
| 96 | (ii) 125 mm dia Ductile Iron Class K-7 pipes. |
| 97 | Charges for cutting D.I. pipe with mechanical cutteras perCPWD specification and direction of the Engineer - in - charge. |
| 98 | i) 100 mm dia |
| 99 | ii) 125 mm dia |
| 100 | Providing and fixing U.P.V.C. service saddle as per CPWD specification and direction of the Engineer - in - charge. |
| 101 | (i) 40mm dia with 15 mm dia opening |
| 102 | ii) 50 mm dia with 15 mm dia opening |
| 103 | iii) 90 mm dia with 15 mm dia opening |
| 104 | iv) 110 mm dia with 15 mm dia opening |
| 105 | v) 140 mm dia with 15 mm dia opening |
| 106 | Providing and laying of flexible PVC pipe (conforming to IS:7634) complete as per specification and direction of the Engineer - in - charge (cost of earth work and fittings will be paid separately). |
| 107 | i) 15 mm dia |
| 108 | ii) 25 mm dia |
| 109 | Excavating trenches of required widthfor pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm(slope-1 in 200)including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge. a. All kind of Soils |
| 110 | A)For UPVC pipes in new work.i) For pipes not exceeding 90 mm dia |
| 111 | A)For UPVC pipes in new work.ii) For pipes exceeding 90mm dia but not exceeding 300mm dia. |
| 112 | B) For GI/CI/DI pipes in new work.a) All kind of Soilsi) For pipes exceeding 90mm dia but not exceeding 300mm dia. |
| 113 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 114 | i) 15 mm dia |
| 115 | i) 65 mm dia |
| 116 | i) 80 mm dia |
| 117 | Providing and fixing G.I. Reducer with the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 118 | i) 80 x 65 mm dia |
| 119 | ii) 100 x 80 mm dia |
| 120 | Installation of submerssible pump with motor upto the depth of 100 ft by GI pipe ( conforming to IS : 1239 medium class ) with tailpiece as required welded with GI flange in/c providing fitting fixing by necessary rubber washer, nuts & bolts, MS safety clamp etc. as per required size and making necessary electrical connection with main switch / starter with motor in/c commissioning & trial run as per direction of the Engineer-incharge (G.I. pipe of medium class for column assembly will be supplied by the agency at his cost)i. 2500 GPH capacity with 50 / 65 mm dia G.I. pipe and 10 mm thick GI flange |
| 121 | Providing & fabrication of column pipe includingfitting fixing of G.I. flange by cutting the GI pipe ( conforming to IS : 1239 medium class ) into 3.05 mtr. long and welding the same with GI flange as per specification and direction of the Engineer-in-charge ( G.I. pipe will be provided by the agency at his own cost & risk). |
| 122 | i) For 65 mm dia G.I. pipe with 10 mm thick GI flange |
| 123 | ii) For 80 mm dia G.I. pipe with 10 mm thick GI flange |
| 124 | Providing, fitting fixing and installation of 5000 GPH x 76 mtrs. Head water lubricated submersible pump of maximum 150 mm outer dia. With maximun 10(ten) stages coupled with required water and non-cover loading submersible motor suitable for 340-440 volts, 3 phase 50Hz, A.C supply and star delta method of starting along with 35 mtrs. x 2 x 3 x 4 sq.mm jointless PVC 3 (three) core double length flat cable (continuous length) of suitable size fitted with submersible motor, suction case, strainer, coupling key, vertical non- return valve cum discharge case including supplying of 10 Nos. suitable cable guard with clipsand nuts & bolts, 2 (two) pair M.S. column clamps as per direction of Engineer-in-charge conforming to terms & conditions of the contract (Each pump with motor shall consists of stainless stell closed type impeller , C.I. bowl, C.I discharge case, pump shaft (styainless steel), bush (bronze), shaft sleeve (bronze/ chromium), sand guard, winding rotor, stator, counter thrust plate, thrust plate, thrust bearing segment etc. conforming to relevant BIS codes of made DUKE/KSB/WPIL/CRI). |
| 125 | Providing & fitting fixing of 2500 GPHX 76 mtr. head water lubricated submerssible pump of maximum 150 mm outer dia with maximum 10(ten) stages coupled withrequired wet and non-over loadingsubmersible motor suitable for 340-440 volts, 3phase, 50Hz, A.C. supply and star delta method of starting along with 35.00 mtr. PVC insulated 3 coreflat copper cable of 4.0 sqmm conforming to relevant IS code for submersible motor with all necessary equipments and fittings as required with suction case, strainer coupling key, vertical non-return valve cum discharge case as per direction of the Engineer-in-charge |
| 126 | Providing and fitting fixing of pressure meter ( 0.0 - 14.0 Kg/ sqcm.) as per specification and as per specification and thedirection of the Engineer - in-charge. |
| 127 | Making road crossing by horizontal boaring for smooth laying of UPVC/CI/DI/GI pipes etc. of required dia complete as per specification and the direction of the Engineer-in-charge.A. By manual means |
| 128 | Constructing masonry Chamber 90 x 90 x 100 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve,with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 190 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :\"(i) With Second Class bricks |
| 129 | Providing and fixing in position Precast RCC hydrant post of size 100 mm dia ( made withreinforced cement concrete 1 : 1.5 : 3 ( 1 cement : 1.5 fine sand : 3 graded well burnt brick aggregate 1st class 12 mm nominal size) and steel reinforcement ( TMT bars )3 nos 8 mm dia 950 mm long and 7 Nos 6 mm dia tiesincluding plastering the surface with 6 mm thick cement mortar 1 : 3 ( 1 cement: 3 sand ) finished with a floating coat of neat cement including providing & embedding 15 mm dia G.I. pipe (medium class as per IS : 1239 ) with necessary GI fittings like 2 Nos elbow, 1 no socket, 2 nos nipple 225mm long and fitting fixing ofPVC bib cockwith GI socket, GI union complete with all earth work required including refilling etc. complete as per approved drawing ( Drawing No-06/CE/ACE/P&DU/DWS/2022-23), specification and direction of Engineer-in-charge. |
| 130 | Providing and fixing in position Precast RCC platform of size 900 mm x 900 mm x100mm with curb of size 75 x 75 mm keping an opening of 200 mm wide for surface drain of 60 cm length of size (200 mmx150 mm) in a suitable place for draining out of grey water (made with cement concrete 1:1.5:3 (1 cement: 1.5 sand: 3 graded well burnt brick aggregate 12 mm nominal size) and steel reinforcement(TMT bars ) 6 nos. 8 mm dia in both direction including plastering the exposed surface with 6 mm thick cement mortar 1:3 (1 cement :3 sand) for platform &12 mm cement plaster(1:4) (1 cement :4 sand) for surface drain finished with a floating coat of neat cement complete with all earth work required including refilling etc. complete as per approved drawing (Drawing No-06/CE/ACE/P&DU/DWS/2022-23), specification and direction of Engineer-in-charge. |
| 131 | Providing and fitting fixing of hoarding cum display board of JJM of size 8 ft. x 6 ft. (2.40 m x 1.80 m) with frame comprising of 40 mm dia GI pipe (medium class) around the board, 2 nos. 25 x 25 x 4 mm size MSvertical stiffners withequally placed and 1 no.25 x 25 x 4mm size MS horizontal stiffner centrally placed and 2 mm thick MS Sheet (2.40 m x 1.80 m) with necessary welding, painting, lettering and erected vertically in such a way bottom of the board shall be placed 900mm above the Ground Level with 2 nos. 40 mm dia GI pipe embedded in cement concrete block of 1:2:4 (1 Cement : 2 fine Sand: 4 graded well burnt brick aggregate 20 mm nominal size) of 300 mm x 300 mm & 900 mm total depth out of which 150 mm shall be projected over GL etc. complete as per specification and direction of the Engineer-in-Charge. |
AI Tender Summary
Tender Timeline
Aug 11, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 31, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender