Construction Of Panchayat Samudayik Kender Panchayat Ghar Bahal At Sainj Dev Block Seraj At Janjehali Distt Mandi Hp Sh Construction Of Building Portion Including Water Supply And Sanitary Installation Etc
Tender Value
33.07 Lakhs
Estimated cost
Bid Submission
16 Aug 2022
0 days left
EMD
66200
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sainj → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Panchayat Samudayik Kender Panchayat Ghar Bahal At Sainj Dev Block Seraj At Janjehali Distt Mandi Hp Sh Construction Of Building Portion Including Water Supply And Sanitary Installation Etc
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work ,pick jumper work , jumper blasting work , soft and hard blasting ,saturated soil , including chiseling or any other mixed variety of soil in all leads dewatering and or removal of slush and other incidentals , including stacking the excavated soil clear from the edge of excavation and than returning thestacked soil in all thickness of layers when required into plinths side of foundation etc. consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 2 | Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement:four sand eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 3 | Providing and laying, mechanically mixed and vibrated cement concrete 1:5:10 (one cement:Five sand Ten graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 4 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) :six graded stone aggregate 20 mm nominal size) over 75mm(seventy five milimetre) thick bed of dry brick ballast 40 mm (forty mimi metre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 5 | Providing and laying M-25grade of concrete with minimum cement contents of 400kg (four hundred kilogrames per cum )mechanically mixed and vibrated graded crushed stone aggregate 20mm nominal size and curing complete excluding the cost of form work and reinforcement for reinforced concrete workincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 6 | Foundation ,footing basis of columns etc and mass concrete as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 7 | In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge |
| 8 | Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, as per direction of the Engineer-in-charge including carriage of material with in all leads , lifts in all floor levels and other incidentals. |
| 9 | Arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° up to all floor level including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 10 | Providing from work with steel plates 3.15 mm (three decimal fifteen millimeter ) thick welded with angle iron in frame 30X30X5 mm (thirty into thirty into five millimeters )so as to give a fair finish including centering , shuttering ,strutting and propping etc. with wooden battens and ballies for all heightsof propping and centering below supporting floor to ceiling & removal of same for in-situ reinforced concrete and plain concrete workincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. in : |
| 11 | Foundation ,footing basis of columns etc. And mass concrete as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 12 | Flat surfaces, such as soffitsof the suspended floors roofs , landing and the like floors etc. up to any thickness , all as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 13 | Beams cantilever girders and lintels side and soffits of beams, beams haunchings, cantilevers, bressumers and lintels any depth in all heights from floor as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 14 | Columns, pillars ,posts and struts square, rectangular or polygonal in plan as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 15 | Stair case with sloping or stepped soffits excluding landing as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals |
| 16 | Form work in edges of slab and breaks in floor and walls under 20 cm wide as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 17 | Providing tor steel reinforcement TMT bar Fe500 ISI make high yield strength for reinforced cement concrete work includingbending ,binding and placing in position and cost of binding wire complete for all floors including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 18 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 19 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in cement mortar 1:4 (one cement: four sand)including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 20 | Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand)as requiredin all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. in :- |
| 21 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.Granite stone shall be got approved from engineer incharge before use. |
| 22 | Providing edge moulding to 18 mm thick granite stone ,marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 23 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 24 | Providing first class sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 25 | Providing and fixing 35 mm thick (thirty-five mili metres) well seasoned hollock wood glazed shutters for doors, windows and clerestory windows using 4 mm (four mili metre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screwsincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 26 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 27 | Providing and fixing 35 mm thickISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shuttersincluding ISI marked Stainless Steel butt hinges with necessary screws including carriage of material with in all leads and lifts and other incidentals . |
| 28 | Extra for providing lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 29 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). |
| 30 | Providing and fixing 35 mm (thirty-five mili metre) thick wire gauge shutters of well seasoned hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screwsincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 31 | Glazing with glass pan 5 mm (five point five millimeters)thick plain glass panes with teak wood beadingincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 32 | Providing and fixing teak wood wooden moulded beading 15x12mm (fifteen X twelve mili metre)to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete |
| 33 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc.Fixed to openings /wooden frames with rawl plugs screwsincluding priming coat with approved steel primer including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 34 | Providing 40x5 mm (Forty X five mili metres) flat iron hold fast 40 cm (forty centimetre)long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm nominal size). |
| 35 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material with in all leads and lifts and other incidentals . |
| 36 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 37 | 300x10 mm (Three hundredX Ten mili metres) |
| 38 | 250x16 mm (Two fifty X Sixteen mili metres) |
| 39 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 40 | 200 mm X 10 mm (One hundred millimeters Into ten millimeters) |
| 41 | 100 mm X 10 mm (one hundredInto sixteen millimeter) |
| 42 | Providing and fixing 50 cm (fifty centimetre) long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete |
| 43 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 44 | 125 mm (one hundred twenty-five mili metres) |
| 45 | 100 mm (one hundred mili metres) |
| 46 | Providing and fixing twin rubberaluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. complete including carriage ofmaterial as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 47 | Providing and fixing aluminium casement stays,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete. |
| 48 | Kota stone slab flooring 25 mm (twenty-five milimetres) thick over 20 mm (twenty mili metres) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand)including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 49 | Kota stone slabs 20 mm (twenty mili metres) thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (oine cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing completeincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.. |
| 50 | Providing and laying 5.5 mm (five point five milimetre) thick Ceramic/Spartic glazed floor tiles of size 300x300 mm (three hundred X three hundred mili metre)of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. The sample and pattern of kajaria/nitco/jonson tiles should be got approved from Engineer - in - charge before use. |
| 51 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. The sample of kajaria/nitco/jonson tiles shall be got approved from engineer incharge before use. |
| 52 | Providing and laying vitrified floor tiles 600x600mmx 10mm thick with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. The sample and pattern of kajaria/nitco/jonson tilesshould be got approved from Engineer - in - charge before use. |
| 53 | Providing and laying Vitrified tiles 600x600x10mm thick , with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.The sample and pattern of kajaria/nitco/jonson tilesshould be got approved from Engineer - in - charge before use. |
| 54 | Providing and fixing 110 mm dia (one hundred ten mili metre) on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 55 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 56 | 110mm bend (one hundred ten mili metres) |
| 57 | 110mm shoe (one hundred ten mili metres) |
| 58 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 59 | 110 mm diameter (one hundred ten mili metres) |
| 60 | 6 mm(six millimeter)thick cement plaster to ceiling in cement mortar 1:3 (one cement :three sand as per direction of engineer-in- charge including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 61 | 15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior plastering for all floors including arises internal roundedangles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement :six sand ) including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 62 | Providing and applying white cement based putty of average thickness 1 mm (one mili meter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 63 | Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with In all leads , lifts in all floors and other incidentals completes as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 64 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 65 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufactureincluding carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 66 | Finishing walls with Acrylic Smooth exterior paint of required shade on New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 67 | Providing Boulder Filling under floor including carriage as requiredcomplete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 68 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera, hindware, parrywaremake with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 69 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) cera, hindware, parryware make with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china orissa pattern W.C.pan of size 580x440mm with integral type foot rests including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 70 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin cera, hindware, parryware make of 430x260x350 mm( four hundred thirty X two hundred sixty X three hundred fifty milimeters)and 340x410x265 mm (three hundred forty X four hundred ten X two hundred sixty five milimeters) sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 71 | One urinal basin with 5 lt. white P.V.C automatic flushing cistern |
| 72 | Providing and fixing White Vitreous China Wash basin cera, hindware, parryware make size 550x400 mm (five hundred fifty X four hundred mili meters)with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: including carriage of material as requiredin all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 73 | Providing and fixing white vitreous china pedestal for wash basin cera, hindware or equivalent make completely recessed at the back for the reception of pipes and fittings. |
| 74 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink 510x1040 mm bowl depth 225as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 75 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. Heavy duty jet quality and sample should be got approved from Engineer - in - charge before use. |
| 76 | Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 77 | Providing and fixing 100 mm sand cast Iron grating heavy duty for gully trap. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 78 | Providing and fixing 600x450 mm beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 79 | Providing and fixing 600x120x5 mm heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 80 | Providing and fixing heavy duty toilet paper holder : C.P. brass complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 81 | Providing and Fixing sand cast iron $ S Pipes as per IS. 1729 soil waste and vent pipes |
| 82 | 100mm dia (One hundred milimetre) |
| 83 | 75mm dia (Seventy five milimetre) |
| 84 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : |
| 85 | 75mm dia Pipes (Seventy five milimetre) |
| 86 | 100mm dia Pipes(One hundred milimetre) |
| 87 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : |
| 88 | For 100 mm dia pipe(One hundred milimetre) |
| 89 | For 75 mm dia pipe(Seventy five milimetre) |
| 90 | Providing and fixing Sand cast iron S $ Sas per IS:1729 bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 91 | 100mm dia (One hundred milimetre) |
| 92 | 75mm dia(Seventy five milimetre) |
| 93 | Providing and fixing Sand cast iron S $ Sas per IS:1729 plain bend of required degree. |
| 94 | 100mm dia(One hundred milimetre) |
| 95 | 75mm dia(Seventy five milimetre) |
| 96 | Providing and fixing Sand cast iron S $ Sas per IS:1729 heel rest sanitary bend |
| 97 | 100mm dia |
| 98 | 75mm dia |
| 99 | Providing and fixing Sand cast iron S $ Sas per IS:1729 double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : |
| 100 | 100x100x100x100mm |
| 101 | 75x75x75x75mm |
| 102 | Providing and Fixing Sand cast iron S $ Sas per IS:1729 Collar |
| 103 | 100mm dia |
| 104 | 75mm dia |
| 105 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : |
| 106 | 100mm dia |
| 107 | 75mm dia |
| 108 | Providing and fixing Sand cast iron S $ Sas per IS:1729 trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 109 | 100mm inlet and 100mm outlet |
| 110 | 100mm inlet and 75mm outlet |
| 111 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 112 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 113 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 114 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 115 | Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. |
| 116 | Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe) |
| 117 | Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes) |
| 118 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 119 | 15 mm dia nominal bore |
| 120 | 20 mm dia nominal bore |
| 121 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall |
| 122 | 15 mm dia nominal bore |
| 123 | 20 mm dia nominal bore |
| 124 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. |
| 125 | 15 mm dia nominal bore |
| 126 | 20 mm dia nominal bore |
| 127 | 25 mm dia nominal bore |
| 128 | Making connection of G.I. distribution branch with G.I. main of 25 to 40 mm nominal borefollowing sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 129 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). |
| 130 | Providing and fixing15 mm nominal boreC.P. brass bib cock ofjaquar/jal/ess ess make of approved quality conforming to IS:8931 : The samplequality & series should be got approved from Engineer - in - charge before use. |
| 131 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cockjaquar/jal/ess ess make of approved quality conforming to IS standards and weighing not less than 810 gms .The samplequality & series should be got approved from Engineer - in - charge before use. |
| 132 | Providing and fixing 15 mm nominal boreC.P. brass long body bib cock ofjaquar/jal/ess ess make of approved quality conforming to IS standards and weighing not less than 690 gms. The samplequality & series should be got approved from Engineer - in - charge before use. |
| 133 | Providing and fixing 15 mm nominal boreC.P. brass stop cock (concealed) ofjaquar/jal/ess ess make of approved make conforming to IS:8931 The samplequality & series should be got approved from Engineer - in - charge before use. |
| 134 | Providing and fixing 15 mm nominal boreC.P. brass angle valve jaquar/jal/ess ess for basin mixer and geyser points of approved quality conforming to IS:8931 The samplequality & series should be got approved from Engineer - in - charge before use. |
| 135 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 136 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 137 | 15 mm nominal bore |
| 138 | 20 mm nominal bore |
| 139 | 25 mm nominal bore |
| 140 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 141 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 142 | Inside dimensions 455x610 mm and 45 cm deep for single pipe line : |
| 143 | Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 144 | Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : |
AI Tender Summary
Tender Timeline
Aug 08, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedAug 16, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 17, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender