Emergent Repair And Restoration Of Damaged Flap Shutter And Bank Protection Of Moni Closer 2Nd Call
Tender Value
24.51 Lakhs
Estimated cost
Bid Submission
18 Aug 2022
0 days left
EMD
49032
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
mathurapur → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Emergent Repair And Restoration Of Damaged Flap Shutter And Bank Protection Of Moni Closer 2Nd Call
BOQ
| Sl. No. | Item Description |
| 1 | Making sausages Square or Rectangular in section (any length) made with 1st class kiln burnt / 1st class picked jhama full bricks rolled inside with 10 S.W.G. galvanised square pattern (internal dimension of mesh will be 100 m.m. x 100 m.m. square) galvanised wirenet caging with proper lapping of minimum 150 m.m. and sewing with 12 S.W.G. galvanised wire including cost of all materials, carriage upto site, placing and laying the same in position, after preparing the bed to proper slope etc. complete as per direction of the Engineer-in-charge. (cost is excluding the cost of end pieces.)c) 0.60 metre x 0.60 metre nominal section |
| 2 | j) 1.00 metre x 1.00 metre nominal section |
| 3 | Supplying, fitting, fixing end pieces for rectangular / square / circular sausages at the ends, with 10 SWG / 8 SWG G I wire net of different mesh sizes tying & sewing the same maintaning a lap length of 150 mm all around with 12 SWG G I wire complete including the cost of supply of wire netting, fitting etc, complete as per direction of the Engineer-in-charge.a) Mesh size 100 mm x 100 mm with 10 SWG wire |
| 4 | Making filler with well graded 40 mm down ballasts and laying uniformly behind weep holes, below pitching on bed, side slopes including supply and carriage of all materials to site including preparing bed with earthwork up to 30 cm depth, where necessary and compacting with wooden malllet after laying to achieve designed section as per direction of the Engineer-in-Charge (measurements will be on finished work / in stack after deducting necessary void).(a) 1st class brick Ballast |
| 5 | Providing and laying pre-cast brick block pitching of required size (53 Cm. x 53 Cm. x 25 Cm. or as directed by the Engineer-in-charge) with 1st class kiln burnt bricks in cement mortar including flush pointing on all faces except exposed face which to be plastered with 19 mm. thick cement plaster, curing, dressing, ramming & preparing subgrade in slopes & bed complete with necessary earth work nol exceeding 300 mm in depth with all leads & lifts including cost of all materials / blocks up to site by all meansof transport. The gap between adjacent blocks will not be more than 10 mm.(Sand, cement mortar rnix for making blocks, pointing & plastering is 1:4) |
| 6 | Earthwork in excavation in all kinds of soil for making embankments, repairs to the embankment, closing breaches etc. as per profile including supply and transporting the earth by truck or tractor or any other mechanical means on land , including loading, transporting, unloading and stacking with all lifts bothways and head load where necessary and depositing the same on embankments, clannels, filling depressions in requisite profile, levelling as per direction of the Engineer-in-charge within a lead ofA) Beyond 500 metre and upto 1.00 km |
| 7 | Supplying, fitting, fixing Mild Steel draw shutter with Mild Steel plate of thickness as specified by the Engineer-in-charge and other necessary Mild Steel sections for sluice including fabricating the same (as per drawing and instruction given by the Engineer-in-charge) excluding cost of Mild Steel guide channel, sill beam, gearing arrangement etc. but including painting with two coats of anticorrosive bituminous paint of approved make & brand over two coat of red lead primer and with necessary masonry work with all materials supply etc. complete at site. |
| 8 | Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic \"J\" type tor making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M.S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-in-charge.(a) Flat Type Rubber Seali) 127mm x 6mm |
| 9 | Oiling, cleaning & greasing the regulator gate & gate parts including guide channel, top runner, pedestal block, gear rods, wheel, fish plate etc. with sufficient lubricant as and when necessary as directed by the Engineer-in-charge including cost of all materials to site complete. |
| 10 | Add GST @ 12% (CGST+SGST) |
| 11 | Labour Welfare Cess @ 1% |
AI Tender Summary
Tender Timeline
Aug 03, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedAug 18, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 23, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender