Conversion Of Sub-Center To Su-Sasthya Kendra ( Hwc ) At Selimpur Sc Under Kaliachak-I Dev. Block, Malda.
Tender Value
7.97 Lakhs
Estimated cost
Bid Submission
16 Aug 2022
0 days left
EMD
16000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kaliachak → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Conversion Of Sub-Center To Su-Sasthya Kendra ( Hwc ) At Selimpur Sc Under Kaliachak-I Dev. Block, Malda.
BOQ
| Sl. No. | Item Description |
| 1 | BUILDING WORKS |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil(including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm.including watering and ramming etc. layer by layer complete. (Payment to be made on the basis ofmeasurement of finished quantity of work)(a) With earth obtained from excavation of foundation. |
| 4 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed andconsolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)(B) Do - by fine sand |
| 5 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 6 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor(A) [Pakur Variety] (a) 1:3:6 proportion |
| 7 | Ordinary Cement Concrete(mix 3 :1.5 :1) with graded stone chips (20 mm. nominal size) excluding shuttering and reinforcement, if any, in ground floor, as per IS codes. (iii) RajMahal |
| 8 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction (upto roof of ground floor) |
| 9 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood plank of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(f) 25 mm to 30 mm shuttering without staging in foundation |
| 10 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood plank of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(a) 25 mmto 30 mm thick wooden shuttering as per decision and direction of Engineer-in Charge. |
| 11 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 12 | Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, ground floor |
| 13 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor |
| 14 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of paintingat the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(c) Sal : Siliguri. |
| 15 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) (iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak |
| 16 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (b) 40mm X 6mm, 200mm Length |
| 17 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(vii) 100mm. X 58mm. X 1.90mm. |
| 18 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt andround fitting. (b) 250mm long |
| 19 | Iron socket bolt of approved quality fitted and fixed complete.(c) 150mm long x 10mm dia bolt. |
| 20 | Iron socket bolt of approved quality fitted and fixed complete.(b) 100mm long x 10mm dia bolt |
| 21 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (b) With round base:(ii) 100 mm grip x 10 mm dia rod. |
| 22 | Anodised aliminium D-type handle of approved M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor)(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. |
| 23 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (b) 20 mm thick plaster |
| 24 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/ staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 6:1 cement Plaster.c) 15 mm thick plaster. |
| 25 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/ staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (c) 10 mm thick plaster |
| 26 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. Using grey cement(iii) 35 mm. thick |
| 27 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 28 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 29 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(ii) Two coats (white in shade)(a) On timber or plastered surface :With super gloss (hi-gloss) - |
| 30 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(ii) Two coats (white in shade)(b) On steel or other metal surface :With super gloss (hi-gloss) - |
| 31 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.In Ground Floor(b) Two coats. |
| 32 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer in Ground floor (Two Coat).c) Super Protective 100% Acrylic Emulsion |
| 33 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. (In Ground Floor)(a) One Coatii) Solvent based interior grade Acrylic Primer |
| 34 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface.Two Coats (Ground Floor) |
| 35 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(A) FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg /Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative(KAJARIA, JONSON, CERA, SOMANI, ORIENT, RAK, NITCO) |
| 36 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative(KAJARIA, JONSON, CERA, SOMANI, ORIENT, RAK, NITCO) |
| 37 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge.(A) Deep Colour & White(KAJARIA, JONSON, CERA, SOMANI, ORIENT, RAK, NITCO)IN FIRST FLOOR |
| 38 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing).(i) 580 mm X 440 mm |
| 39 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.(a) Sink only(ii) 630 mm X 550 mm X 180 mm |
| 40 | Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.(ii) 550 mm X 400 mm size |
| 41 | Supplying, fitting and fixing pillar cock of approved make. |
| 42 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(ii) 25 mm dia. and 600 mm long |
| 43 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 44 | Submersible Pump |
| 45 | As per S & P Schedule Page No-49 Item No-1. Labour for boring tubewell of required diameter by water jet system through any kind of soil i/c hire and labour charges for boring pipes, scafolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting fixing same complete i/c bucketing fixing of tubetubewell head in position and other related incidental works in the connection.The tubewell should have a min 50mm gap in between the outside of tubewell pipe and bore. For depth upto 150m, 50mm dia. tubewell with top enlargement 100mm dia.a) 50 mm dia. Boring. |
| 46 | As per S & P Schedule Page No-49 Item No-1. Labour for boring tubewell of required diameter by water jet system through any kind of soil i/c hire and labour charges for boring pipes, scafolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting fixing same complete i/c bucketing fixing of tubetubewell head in position and other related incidental works in the connection.The tubewell should have a min 50mm gap in between the outside of tubewell pipe and bore. For depth upto 150m, 50mm dia. tubewell with top enlargement 100mm dia.b) 100 mm dia. Boring. |
| 47 | As per S & P Schedule Page No-53 Item No-9. Supplying fitting fixing of steel cutter piece upto 450 mm long with socketsa) 40 mm dia. |
| 48 | As per S & P Schedule Page No-13 Item No-19(III) Supply P.V.C. rigid pipe & fittings (Medium Duty) conforming ASTMD -1785 & Threaded to match with GI- pipes as per IS: 1239 (Part-I) a) PVC rigid pipes (Dia) 40 mm |
| 49 | As per S & P Schedule Page No-13 Item No-19(III) Supply P.V.C. rigid pipe & fittings (Medium Duty) conforming ASTMD -1785 & Threaded to match with GI- pipes as per IS: 1239 (Part-I) b) PVC rigid pipes (Dia)80 mm |
| 50 | As per S & P Schedule Page No-13 Item No-19(III) Supply P.V.C. rigid pipe & fittings (Medium Duty) conforming ASTMD -1785 & Threaded to match with GI- pipes as per IS: 1239 (Part-I) c)Threaded Adopter (Dia)40 mm |
| 51 | As per S & P Schedule Page No-13 Item No-19(III) Supply P.V.C. rigid pipe & fittings (Medium Duty) conforming ASTMD -1785 & Threaded to match with GI- pipes as per IS: 1239 (Part-I) d) Reducing Sockets40 x 80 mm dia |
| 52 | As per S & P Schedule Page No-110 Item No-16 Supplying fitting & fixing of G.I. reducing elbow. (x) 40 mm X 32 mm |
| 53 | As per S & P Schedule Page No-56 Item No-28 Supplying fitting & fixing of200 mm centre guide.i) With Clamp |
| 54 | Non Schedule Item(Rate adopted from local Market price)-Supply and fitting 2.5 mm gauge water proofing cable wire for fitting submersable motors. |
| 55 | Non Schedule Item(Rate adopted from local Market price)-Supply,fittings, fixing01 H.P. Submersable pump with motor of 100 mm dia of approved make and brand (Crompton) with panel box, cable and all necessary fittings. |
| 56 | Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with \"V\" notch including hire and labour charges for all tools and plants and scaffolding as required. |
| 57 | Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction. |
| 58 | Packing the annular space between the outside of the tube well pipes & strainers and the bore with pea size washed gravel of approved quality having size from 2 mm to 5 mm or the size approved by the Engineer-incharge including cost of all materials labour and equipment complete. |
| 59 | Packing annular space between the outside of the housing pipe and the bore with puddled clay balls of approved size as per direction of the Engineer -in-charge with cost of all materials and labour complete. |
| 60 | Labour for making arrangement for showing verticality test including the cost for hire charges of tools and plants, scafolding, labour etc. all complete. |
| 61 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. |
| 62 | Cost of Electrical Works as per Model Estimate |
| 63 | Goods and Service Tax @ 12% |
| 64 | Labour and Welfare Cess @ 1% |
AI Tender Summary
Tender Timeline
Aug 01, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedAug 16, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 18, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender