|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 2 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks) |
| 3 | Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm). |
| 4 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 5 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall25 mm nominal dia Pipes |
| 6 | 32 mm nominal dia Pipes |
| 7 | 40 mm nominal dia Pipes |
| 8 | 50 mm nominal dia Pipes |
| 9 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc20 mm nominal dia Pipes |
| 10 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter |
| 11 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 12 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 13 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 14 | providing, fitting and fixing of panelling in column, walls, doors, windows frames upto ceiling level where necessary with 19mm thick ply wood board and pasting with 1mm thick century laminates and making gooves or making design as per approved drawings icluding varnishing and polishing where ever necessary complete as per direction of the department. |
| 15 | Supplying including Installation, testing and commissioning of 3 Watt LED Recessed Down Light fixtures complete with all accessories including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required (Rate as per analysis enclosed) |
| 16 | Supplying including Installation, testing and commissioning of 6 Watt LED Recessed Down Light fixtures complete with all accessories including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required (Rate as per analysis enclosed) |
| 17 | Supplying with fitting and fixing of 25A Modular Motor Starter, 2Module typecomplete with 2 Module Board & 2 Module front Plateincludingmaking necessary connection as required and as directedbythe department.(Rate as per analysis enclosed) |
| 18 | Supplying including fitting fixing Special FinishA.C. Ceiling Fans 1250 mm, Pine Wood Cola complete with all accessories like down rod, canopy etc. including connection as required and as directed (Rate as per analysis enclosed) |
| 19 | Supplying and fitting fixing of electric storage water heater [Geyser], 25.0 Ltr Capacity (Vertical) including necessary connectionetc. as required complete and as directed by the Department. (Rate as per analysis enclosed) |
| 20 | Supplying and fixing brass batten/ angle holder including connection etc. as required. (Rate as CPWD Electrical SOR\"2018 including 23.98% Premium = 117.00 + 23.98% = 145.06) |
| 21 | Supplying of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 1.50M X 1.60MX 0.40M made of 16 SWG1.66 m thick C.R. sheet and40mm X 40mm X 5mm size angle having 4 no legs at the bottom. The panel board is to be erected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly Wiring done with provision for one no 400A 4pole MCCB or Switch Fuse Unit as incomer and provision for 8nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items:1 40mm X 5mm x 1.5 mtr, 4 strip copper Bus - Bar 1.50 M length each 2.20mm X 3mm 4 strip copper Bus-Bar 0.5M each 8 sets3. Digital 3 Phase Voltmeter Accuracy class 0.5- 1 no4. Digital 3 Phase Ammeter Accuracy class 0.5- 1 no5. Pilot Lamp with integral ckt LED 110- 230 V (Red, Yellow,& Blue - 3 nos Voltmeter & Ammeter Selector Switch- 2 no6. 2 A Slide fuse unit - 3nos(Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately) (Rate as per analysis enclosed) |
