|
| 1 | Supply, Installation, Testing & Commissioning of 2-way ceiling mounted music and PA loudspeaker with 2-way ceiling mounted music and PA loudspeaker. The loudspeaker shall meet the following performance criteria: Usable Frequency range (-10dB) of 75Hz to 20kHz; Power handling of 100Watt peak; Nominal dispersion of 155° Conical; Sensitivity of 83 dB SPL and Max SPL of 103 dB SPL peak; Nominal impedance of 8 Ohms with an Integral multi-tap Transformer with selectable tap settings of 6/12/25W@100V or better. The loudspeaker system shall be comprised of a powder-coated magnetic steel grill; 3.25-inch woofer enclosed in engineered-plastics with integrated steel backcan and an In-built waveguide designed to provide uniform area coverage across the loudspeakers frequency range. UL-1480A rated and UL2043 rated for plenum-space installation.(Pair) |
| 2 | Supply, Installation, Testing & Commissioning of 8-channel bridgeable class D power amplifier with 8-channel bridgeable class D power amplifier with dynamic output power 8 ohms in watts 8 x 175, power consumption (max) in watts-2200, power supply 115 - 230 VAC, output channels 8, line input unbalanced 8, channel separation > 60 dB @ 1 kHz. Should be able to used to create 8 zones in mono, 4 zones in stereo, even 4 bridged mono or 2 bridged stereo systems can be created. A handy input overload LED indicator and amplifier clip indicator should be there.output power 8 ohms in watts - 8 x 125. |
| 3 | Supplying, installation, testing and commissioning of Digital Signal Processor with Digital audio DSP with 32-bit fixed/floating-point DSP 456 MHz/ARM Cortex-A8 600 MHz processor or better with following features and specifications are required. The DSP shall have 12 balanced inputs and 8 balanced output channels for microphone or line-level analog audio signals, each independently controllable . The DSP shall contain 12 channels of acoustic echo cancellation (AEC), with multiple references, routable to analog and/or Dante® inputs. The DSP shall have Dante digital audio networking up to 64 x64 channels, an Ethernet connection for control and programming on an RJ-45 jack and VoIP connection for 2 lines, GPIO – 5x5 expandable general-purpose contro, PSTN and USB audio and 8 digital channels on an RJ-45 jack.It shall haveIT web configuration page, USB Port – Micro-B USB for PC soft codecs with stereo input and output,ultra-low latency digital audio, Serial Port – 3-wire RS-232C (DTE) serial interface connection. It shall Supports remote zone controllers, PSTN (RJ-11) – Supports worldwide analog telephone connection, Dynamic Range> 115 dB, A-weighted 20 Hz – 20 kHz;THD : < 0.002 % or better ,Maximum Input Level +24 dBu;Phantom Power +48 VDC, 10 mA, selectable per input. The audio DSP shallinclude configurable signal processing, signal routing and mixing, equalization, filtering, dynamics, delay, conference room router, conference room combining, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy allexpansion devices and other Dante endpoints. |
| 4 | Supplying, installation, testing and commissioning of Wireless Handheld Microphone with Audio Frequency Range – 470-937 MHz, Type : Dynamic, Transparent 24-bit digital audio, Frequency Response : 20 to 20,000 Hz, Support upto 32 compatible channels per frequency band, Tuning Bandwidth – 44MHz, Dynamic Range – 120dB, Polar Pattern : Supercardioid, Frequency Auto Scan Functionality, Range – 300 ft, RF Transmitter Output : 1/10 mW, Switchable, Frequency and Power Lock out, THD – <0.02%, Latency – 3.2ms, Sensitivity - -97 dBm |
| 5 | Supply, Installation, Testing & Commissioning of Boundary Microphone with Boundary Microphone with Mute Switch and LED Indicator, TYPE: Condenser (electret bias), Frequency Response: 50–17000 Hz, Polar Pattern: Cardioid, Output Impedance: EIA Rated at 150 O (180 O actual), Sensitivity (at 1 kHz, open circuit voltage): –27.5 dB V/Pa (42.2 mV), Maximum SPL: 118.8 dB, Equivalent Output Noise: 22.6 dB SPL, Signal-to-Noise Ratio: 71.4 dB, Dynamic Range: 96.2 dB, Power Requirements: 11–52 Vdc phantom, 2.0 mA. |
| 6 | Supply, Installation, Testing & Commissioning of Intractive Display with the following specification UFD-190.5 cm diagonal) LCD, Installation Landscape,Resolution 3,840 × 2,160 pixels,350 cd/m2, Contrast Ratio 1,200 : 1,Viewing Angle -178, Backlight-LED, direct lit,Touch Technology-IR (infrared blocking detection method), Multi Touch-20 points, Protection Glass-Thickness: Approx. 4.0 mm, 1mm gap between the screen and tempered glass, SOC - 1.5GHz or higher Inbuilt quad-core processor with 1GB Memory & 8GB storage, HDMI x 3, VGA x 1, USB2.0 Type A x 3, USB3.0 Type A x 3, RS232 x 1, SPDIF x 1, USB2.0 Type B x 2, USB blocking feature, Output Terminals-Audio Out 1, Touch USB Out 1,-Speaker Output 10 W + 10 W,Ethernet(RJ45)- 1, Dolby Digital or above /AAC/ MP3/ PCM/DTS/DTS-HD/DTS Express/WMA |
| 7 | Supplying, installation, testing and commissioning of 55\" Display with 4K, 138.783 cm] diagonal) LED,Max. Resolution 3,840 × 2,160 pixels,Max. Display Colours1.07 billion colours,360cd/m2 NITS, Contrast Ratio -1,300:1, Viewing Angle -178,Response Time-8MS, Backlight-LED Edge,Input Terminals-HDMI In 3, RF In (tuner), AV In (3.5mm), Digital Audio Out (Optical), RS-232C (D-Sub 9pin, Control & Service), RJ45 2 (Ethernet, SNMP), External Speaker Out (3.5mm, Stereo, Max 1W with 8?), Service Only (3.5mm), , USB (2.0), Speaker 20 W |
| 8 | Supply, Installation, Testing & Commissioning of Cable Cubby with the following specification The Hardware should have following connectivity: 2 x Universal Power, 1 x USB Charger, RJ45 Network, HDMI 2.0, |
| 9 | Supply, Installation, Testing & Commissioning of 4K@60Hz 4:4:4 8X8 HDMI Matrix Switcher, 8 HDMI inputs , 8 HDMI Outputs, audio embedding for each HDMI inputs & audio de-embedding for each HDMI output, 8 balanced audio stereo audio outputs, 2K and 4K support, HDCP Compliant 1.4 & 2.2 both, data rate 18Gbps, supports HDR10, 24x24 audio matrix (8 embedded digital inputs + 8 analog inputs + 8 ARC inputs and 8 digital outputs + 8 analog outputs + 8 ARC outputs), Save up to 16 preset configurations, Automatic input selection based on priority selection or last connected input, Embedded Pattern Generator, Controllable through Ethernet and RS-232, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001, etc complete as required. |
| 10 | Supply, Installation, Testing & Commissioning of 4K@60Hz 4:4:4 Switcher with 4 HDMI inputs, 1 HDMI Output with de-embedded analog audio output, 2K and 4K support, Min. data rate data rate of 17.82Gbps, HDTV Compatible, HDCP 2.2 & HDR10 Compliant,Automatic Switching, 1 Unbalanced Stereo Audio: On a 3.5mm mini jack, Controllable through contact closure switches, Supporting deep color, x.v.Color™, CEC, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D as specified in HDMI 2.0, Multi–channel Audio Switching — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound, Controls: Input selection buttons. DIP–switches for configuring switching mode and EDID mode, mini USB port for firmware upgrade, Health, Safety, Environmental: RoHs, WEEE, CE etc complete as required. |
| 11 | Supply, Installation, Testing & Commissioning of HDMI To USB Convertor with Input Port 1×HDMI & 1×Stereo (3.5mm), Output Port 1×HDMI & 1×USB 3.0 (Type-B), HDMI Compliance HDMI 2.0, HDCP Compliance 2.2 bypass, Input Signal Type 4K@60 8bit, Output Signal Type 4K@60, Power Consumption 7.15W, Chassis Material Metal (Steel), Field Firmware Update- USB |
| 12 | Supply, Installation, Testing & Commissioning of HDMI PIP Processor with having minimum technical specification: 2ChannelHDMIPIP/POPProcessorcapableofscalingupto2HDMISourcesanddisplayingthen simultaneously on a single HDMI Output, Inputs and Outputs support Full HD Resolutions upto 1080p 60fps, audio passthrough of 7.1 channel, Supports PIP, Side by Side and Free Positioning window modes, support Chromakey and unloadable logo support. Interfaces: Input Port: 2 x HDMI (Type-A); Output Port: 1 x HDMI (Type-A); 1 x Balanced Stereo (5-pin Terminal Block); Control I/O: 1 x RS-232 (DE-9); 1 x Ethernet (RJ-45); 8 x Triggers (10-pin Terminal Block); Service Port: 1 xUSB(Type-A);Video:HDMICompliance:1.3;HDCPCompliance:1.3;InputSignalType:1080p6012-bit; Output Signal Type: 1080p60 12-bit; Maximum Input: HDMI: 1920×1080p@60; 1920×1200p@60RB; Maximum Output: HDMI: 1920×1080p@60; 1920×1200p@60RB;Audio: HDMI: LPCM (8 Channels), Bitstream, High Bit Rate Bitstream; Line Out: 2 x Vrms; S/N Ratio: > 110dB (1kHz with 0dBFS); |
| 13 | Simultaneous Wired and Wireless Presentation and Collaboration Solution: Wireless presentation device allows users with laptops or mobile to connect and present, HDMI input to connect a source with HDMI directly, 1 HDMI & 1 Mini DP/VGA output, one Gigabit LAN Ethernet port, audio de-embedding feature with one 3.5mm mini jack line out, Wireless Connection for up to 252 user devices, present minimum 4 users laptops or handheld devices on a single display at a time, capable of replicating any iOS device without any required app/device, 4 nos. of USB3.0 port for connecting peripheral devices like keyboard & mouse, share uninterrupted HD video of 1080p @ 60 FPS, feature to stop someone else from presenting to enable uninterrupted presentation, an audio de-embedding feature, annotation & white board feature on both wired & wireless source connected, DHCP support, inbuilt/external Wi-Fi, feature to call the output view of the wireless presenter on any of the connected devices for viewing or annotation, file sharing option for all participants, minimum 32GB (SSD) inbuilt memory, file viewing/downloading option from inbuilt memory, Powerful security features: user authentication, 1024–bit encryption, dynamic room code, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001 Extra component or equipment maybe added to match the complete specs. |
| 14 | Supply, Installation, Testing & Commissioning of Mini PC For Soft VC Like Zoom, Google Meet and Microsoft teams with Intel Core i3 10th Gen or higher, 4gb ram, 512 ssd. With licensed OS |
| 15 | Supply, Installation, Testing & Commissioning of Video Conferencing Unit with following specification Video Standards: Latest video standards H.264, H.264 High Profile/H.265 or better, Video Frame Rate : Should support 60 fps with 1080p resolution., Video Features : Ability to send and receive two live simultaneous video sources in a single call, so that the image from the main camera and PC or document camera can be seen simultaneously, Should support H.239 and BFCP protocols, The system must have the ability to pair with laptop for sending content without any wires to the VC system, In case the above feature is not available natively, then additional components can be provided to achieve this. Video Input : Should have at least 1 x HDMI inputs to connect Full HD cameras ,Must have 2 HDMI inputs to connect two laptops/PC for presentations,All inputs should support 1080p60, The system must have the ability to pair with laptop for sending content without any wires to the VC system, Video Output : Should have at least 2 no.\"s of HDMI output. for both Video and Content. When not in a VC call, it should be possible to view presentation from two laptops on each of the screen so that users can collaborate. Audio standards supported : G.711, G.722, G.722.1, 64 kbps MPEG-4 AAC-LD standard must be supported, Other Desirable features : Noise Reduction, Automatic Gain control, Acoustic Echo Canceller, Active Lip synchronization, Audio Inputs : Should support 3 Microphone inputs to connect 3 microphones. The pick up of the microphones should be at least 10 feet from the microphone, Echo Cancellation for every input must be available , Audio Outputs :Should support audio output,Network Interfaces : 1 LAN /Ethernet--10/100/1000 Mbps full duplex, Bandwidth : H323/SIP upto 6 Mbps point-to-point, Network Capabilities : Packet Loss Based Downspeeding , H.323/ IP Features : QoS--DiffServe, IP adaptive bandwidth management (including flow control), Auto Gatekeeper discovery, Auto Network Address Translation( NAT) support, Standards based- Packet Loss Recovery feature ,System should support IPv4 and IPv6 from day one, Should support URL Dialling, Support for H.245 DTMF tones in H.323, Security : Menu Control : Password protected system menu, Encryption of video call : ITU-T standards based Encryption of the video call, Call should be encrypted end-to-end on IP, Should support Standards-based: H.235 v3 and AES Encryption via Automatic key generation and exchange. The same should be available in a call with Video with presentation (dualvideo), Ability to manually turn encryption ON/ OFF should be there, Automatic key generation and exchange, Management : System Management using HTTPS and SSH. VC Camera with following specification Should have at least two or more HD cameras to automatically detect active speakers in the conference room. The camera should also have face detection mechanism to enable automatic framing of participants, The camera must have a resolution of at least 4K with 3X Zoom or 2K with 4X Zoom, The camera should automatically detect who in the room is speaking and select the best camera framing for that person. And when no one is speaking it should automatically select the best group framing, The system should be capable of providing metrics such as participant count that could be used for resource utilization, The Camera and codec should be from the same manufacturer, Should have at least 72 degrees horizontal field of view. Directory services : Should support Local and Global directories, Should support LDAP and H.350 protocols for directory transfe. VC Control Touch User Interface must be equipped with an intuitive Touch Screen/Panel. The whole package should include -Basic Support for Cisco Spark (Web support), Included VoIP, Cloud Device Registration (For 36 Months), NU Pro Pack for Cisco Webex Control Hub (Recording of VC session) {For 36 Months}. License for the package should be 36 months. |
| 16 | Supply, Installation, Testing & Commissioning of Automation control Processor, Should have Onboard SDRAM 512MB or more & 4GB Flash memory or more and memory card slot support SD/SDHC cards upto 32 GB or more, Built-in 1x Bidirectional RS-232/422/485 or more, 2x Bidirectional RS-232 ports or more, 8x 1way Serial/IR ports or more, 8x Relay ports or more, 8x versiports or more, Should have astronomical time clock for programming event, and scheduling, Should support: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, DHCP, SSL, TLS, SSH, FIPS 140-2 compliant encryption, IEEE 802.1X, SNMP, IPv4 or IPv6, Active Directory authentication, IIS v.6.0 Web Server, SMTP e-mail client,should support BACnet either internal or with a suitable external interface to be provided. Should have Customizable user interface, capable of real-time feedback and Metadata. Support 10 programs to run simultaneously, so as to segregate different genre program in different slots. should have 4wire network control port for communicating and controlling with other devices of the same OEM. Should Support computer and web based controls from GUI. And control apps to integrate iPhone®, iPad®, and Android™ devices. |
| 17 | Supply, Installation, Testing & Commissioning of Module for Light Control with DALI interface, Should be DIN Rail Mountable and 9M wide or less, Should have two Independent DALI loops, Should support 128 DALI Ballasts or more, Should be capable of communicating with external control system, The unit should be addressable so that multiple units of same kind can be controlled via single communication port in a control system, Should be powered via PoE or 4wire network port.Should be of same OEM of Control processor |
| 18 | Supply, Installation, Testing & Commissioning of High Voltage Relay array, should be DIN rail mountable 9M wide or less, should have 8 channels of power switching or more,with Built-in8 voltage-driven isolated digital inputs, or provide an external digital input port. Should Support for 120 to 240 Volt 50/60 Hz lighting and motor loads, Should support Per Channel 10 Amps incandescent, 5 Amps fluorescent, 0.5 HP at 120 to 240 Volts AC, 50/60 Hz; 5 Amps at 30 Volts DC; 16 Amps Resistive or more, Total Module should support 80 Amps incandescent, 40 Amps fluorescent at 120 to 240 Volts AC, 50/60 Hz or more. Should be capable of communicating with central control system, The unit should be addressable so that multiple units of same kind can be controlled via single communication port in a control system. Should be of same OEM of Control processor |
| 19 | Supply, Installation, Testing & Commissioning of Keypad with 10buttons, which can do Button Events allowing different actions to be triggered depending on whether you tap, double-tap, or hold the button, option for Backlit Button Engraving, Enhanced LED Feedback at each button, Auto-Brightness Control, Contact Closure Inputs for low-voltage contact-closure devices such as door switches and motion detectors and should be connected control processor with simple 4-wire network bus that provides bidirectional data communication and 24 VDC power to each keypad in the system. Should be of same OEM of Control processor |
| 20 | Supplying, installation, testing and commissioning of 10\" Touch Panel For Conference Room with 32 GB & Wifi Minimum 10.2-inch Retina display and stereo system, with a thin and light design and fast Wi-Fi and 4G LTE, up to 10 hours of battery life |
| 21 | Supplying, installation, testing and commissioning of 15U Network Rack with cooling facility & all other accetries For Conference Room 36U Network rack for equipment placing, Cooling fan 4 Nos., Self 2 Nos, 5/15 Power strip with 5 socket 2 Nos., Cable manager 4 Nos etc. |
| 22 | Supply, Installation, Testing & Commissioning of 1 Pair 22 AWG stranded (7x30) TC conductors, Material :polypropylene insulation, paper wrap, twisted pair, overall Beldfoil® shield (100% coverage), 22 AWG stranded TC drain wire, Outer Jacket Material : PVC - Polyvinyl Chloride Thickness: 0.020 in, Nom. Diameter :0.138 in, Outer Shield Material : Bi-Laminate (Alum+Poly) Complete as required. |
| 23 | Supply, Installation, Testing & Commissioning of2 Conductor 16 AWG stranded (19x29) tinned copper conductors with polyolefin insulation, Riser, PVC jacket with ripcord.Max. Recommended Current [A] : 6.25 Amps per Conductor at 25ºC,Complete as required |
| 24 | Supply, Installation, Testing & Commissioning of High-quality low-smoke, halogen free cableShould have 4 shielded twisted pairs (U/FTP) of 23AWG solid Annealed copper conductors Should have outer jacket with Material: LSHF, Thickness: =0.5mm, Diameter: 7.2mm ±0.2mm Should have Drain wire with material: Tinned copper, Diameter: 0.4mm ±0.01mmShould have Delay Skew: <45ns, Propagation Velocity (NVP): 76%Should have electrical Impedance: 1–100MHz: 100? ±15?, 100–250MHz: 100? ±20?, 250–500MHz: 100? ±25?Operation Temperature: –20°C to +60°CCOMPLIANCE - Electrical: EIA/TIA 568A, ISO/IEC 11801, Fire Performance: IEC 60332 1, Smoke Density: IEC 61034, Halogen Free: IEC 60754, RoHS: 2011/65/EU, Reaction to Fire Classification: Dca–s2,d1,a1 (optional: B2ca–s1,d1,a1)Should be recommended by HDBaseTShould be from the same OEM as of video switcherShall be supplied with adequate no of connectors for this shielded CAT6A cable from the same OEM |
| 25 | Should be High Speed with Ethernet HDMI Cable, that supports signals up to 1080p@60Hz 12-Bit, Deep Color. Should have 24k gold Plated pins. Should be 24AWG (7/0.20). Should support Data Transfer rate of upto minimum 6.75GBps. Connectors must have a minimal locking capability to prevent ousting of cables from ports. Should have an overall shield against EMI/RFI interference. Safety: Flammability Rating — CL3/FT4 Environmental: RoHS 2011/65/ EU |
| 26 | Transmitter: Should accept HDMI and give out HDBaseT. Should support bi-directional RS-232 and IR signals. Should support a minimum data rate of 10Gbps. Should carry HDMI signal over 70m. Should be HDTV and HDCP 2.2 compatible. Should have 2K and 4K support. Should have 3D pass through. Should have support for Deep Color, x.v.Color™, Lip Sync, HDMI, Uncompressed Audio Channels, Dolby TrueHD, DTS-HD, CEC. Safety Regularity Compliance : CE, ISO 9001:2008 Receiver: Should accept HDBaseT and give out HDMI. Should support bi-directional RS-232 and IR signals. Should support a minimum data rate of 10Gbps. Should carry HDMI signal over 70m. Should be HDTV and HDCP 2.2 compatible. Should have 2K and 4K support. Should have 3D pass through. Should have support for Deep Color, Lip Sync, HDMI Uncompressed Audio Channels, Dolby TrueHD, DTS-HD, CEC. Safety Regularity Compliance : CE, ISO 9001:2008. Transmitter & Reciver Should be of same OEM |
| 27 | Supply, Installation, Testing & Commissioning of 25 Feet HDMI Cable with High-performance HDMI cable that supports signals up to 1080p. Should have 24k gold Plated pins. Should have lockable connectors. Should be 28 AWG. Triple Shielded — For maximum EMI protection. Safety: Flammability Rating — CL3/FT4, Environmental: RoHS 2011/65/ EUConductor Resistance – 28AWG: 237.25?/km |
| 28 | Supply, Installation, Testing & Commissioning of 35 Feet HDMI Cable with High-performance HDMI cable that supports signals up to 1080p. Should have 24k gold Plated pins. Should have lockable connectors. Should be 28 AWG. Triple Shielded — For maximum EMI protection. Safety: Flammability Rating — CL3/FT4, Environmental: RoHS 2011/65/ EUConductor Resistance – 28AWG: 237.25?/km |
| 29 | Supply, Installation, Testing & Commissioning of 3 feet HDMI Cable High-performance cable that supports signals up to 4K@60Hz (4:4:4), Deep color Should have Gold Plated pins. Should be 28 AWG. Triple Shielded — For maximum EMI protection. Conductor Resistance – 28AWG: 237.25?/km Safety: Flammability Rating — CL3/FT4 |
| 30 | Supply, Installation, Testing & Commissioning of 6 feet HDMI Cable High-performance cable that supports signals up to 4K@60Hz (4:4:4), Deep color Should have Gold Plated pins. Should be 28 AWG. Triple Shielded — For maximum EMI protection. Conductor Resistance – 28AWG: 237.25?/km Safety: Flammability Rating — CL3/FT4 |
| 31 | Crimp-style shielded RJ-45 connector for conductors in a 26AWG to 22AWG twisted pair shilded cable with an overall insulation diameter of 1.40mm to 1.50mm. |
| 32 | PVC conduit of dia 20 mm to 25 mm as per site requirement along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(Recommended make : AKG/ BEC/ Precision) |
| 33 | Connector (Lot) |
| 34 | Installation, Programming and Project Management |
