Public Health Engineering Department-PHED has published Supply, Installation, Testing And Commissioning Of Electro-Mechanical Equipments And Construction Of Pump House / Panel Room / Operator Room At Various Water Supply Schemes Of Bijbehara Sub Division Of Jal Shakti ( Phe ) Mechanical Division. Submission Date for this Tender is 29-08-2022. Pump House Construction Tenders in bijbehara Jammu And Kashmir. Bidders can get complete Tender details and download the document.
Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
1 | 13-Aug-2022 | Extension Notice | Date | 22-08-2022 |
2 | 23-Aug-2022 | Extension Notice II | Date | 29-08-2022 |
Sl. No. | Item Description |
1 | 01.WSS Tengpora Panzath (Adv. Cost: Rs. 7,75,384/-) |
2 | Supply, Installation, Testing & Commissioning of Submersible Pumping Unit as per IS 8034 with following specification are as under: PUMP: Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump = Mixed flow. Type of fluid to be handled = Clear Water MATERIAL OF CONSTRUCTION: Impeller = Stainless Steel Pump Shaft = Stainless Steel SS 410. Pump Casing Cast Iron/Stainless steel IMPELLER: Impeller is of the enclosed or semi – enclosed type and properly balanced. Enclosed Impellers equipped with seal rings on their hubs. COUPLING: A suitable coupling arrangement provided with pump set. Non Return Valve: - Non Return Valve of the suitable size provided above the pump discharge case. MOTOR:- Method of starting = Star – Delta Speed = 3000 (Sync). Frequency = 50 ± 3 % Hz Working Voltage = 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Rating = Suitable for above parameters Class of insulation = F/Suitable for above parameters Manufactures Test Certificate to be apended and Detailed specification as per cluase 1 of of SBD Rating: 20 HP |
3 | Fabrication, Providing and fitting of Y- junction having 1m length of each armto be fabricated out ofhot dip galvanized G.I, 100mm dia.C-Class pipe . The job also includes Providing and welding of M.S flanges to the ends of each arm . the Thickness of flange shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using reputed make electrodes to form strong welding joint by dint of DC arc welding. The job further includes Providing and Fitting of nuts and bolts (conforming to IS:1363 Part 1st) and Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. The |
4 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seated 100mm diameter glandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units. The body and bonnent of the valve shall be of ductileiron, wedge with fully vulcanized EPDM rubber(Approved for drinking water) and NBR seal. The Gate/Sluice valve shall be compatible for buried applications and shall be safe to install in both horizontal and vertical positions. It shall have electrostatic epoxy coating(approved for drinking water) both inside and outside of the valve. The valve shall be supplied along with hand wheel. Cost on account of Nuts, bolts, gaskets, etc required for the job is included in the scope of work. The job includes providing and fitting of 02 nos. M.S flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement. Nuts and Bolts Nuts and Bolts (conforming to IS:1363 Part 1st) Rubber Insertion Gaskets Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. |
5 | Providing and fitting ofDuctile Iron double flanged, Slanted seat 100mm diameter swing check valve( NRV) as per IS 5312. The body shall be of ductile cast iron with fully encapsulated vulcanized EPDM rubber(Approved for drinking water). The valve shall be compatible for buried applications and shall be safe to install in both horizontal and vertical positions. It shall have electrostatic epoxy coating (approved for drinking water) both inside and outside of the valve. Cost on account of Nuts, bolts, gaskets, etc required for the job is included in the scope of work. The job includes providing and fitting of 02 nos. M.S flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with Rising main of the pumping unit at appropriate spots as per site requirement. |
6 | Fabrication, Providing and fitting of90-120 degree bend/elbowto be fabricated out of100mm diameter Class-C, G.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. |
7 | Fabrication, providing and fitting of washout 100mm dia.Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I C-class pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. |
8 | Providing/Fitting& Installation & Testing of , outdoor type100KVA of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound100 KVA Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. The HT transformer is completely filled with suitable grade transformer oil up to required level. The job includes carriage,and all leads and lifts involved. The HT transformer shall be of reputed make from an ISO certified company as per relevant standards and a test certificate shall be provided before installation. The transformer shall also be provided with breather fill with silica jel crystals , conservator with oil level indicator , explosion vet and adequate radiator fins/ Tubes. The impedance of transformer shall be as per IS:1180 (Part 1) 2014 with latest amendments. NOTE: The scope of the work shall include providing ofnecessary test certificate from the concerned Manufacturer for all the required equipment. |
9 | Providing, fitting, testing and commissioning of 75 KVA voltage stabilizer as per specifications below: Type of voltage controller: Manually operated copper wound, 3-phase, AC power supply multi step. Type of Regulator : Double plate type with electrolytic copper contacts. Input voltage : 250-400 volts.(3 phase) Output voltage : 400 ±10% volts. Frequency : 50 ±3 C/S. Windings : Electrolytic grade copper of adequate section, vacuum impregnated and Rest specification as per cluase "44" of SBD. |
10 | Providing/supplying and fitting of 100 mm diameter G.Iclass B flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-C confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). The flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. Flanges (as per IS 6392/1997 Table:17) Thickness shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using reputed make electrodes to form strong welding joint. Welding Electrode DC Arc Welding using welding electrode having diameter not less than 4mm. Nuts and Bolts Nuts and Bolts (conforming to IS:1363 Part 1st) Rubber Insertion Gaskets Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. The rising main is to be laid as per the instructions of the engineer in charge. |
11 | 02.WSS Dialgam-B (Adv. Cost: Rs. 3,40,491/-) |
12 | Supply, Installation, Testing & Commissioning of Bore Well Submersible Pumping Unit as per IS 8034 with following specification are as under: PUMP: Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump = Mixed flow. Type of fluid to be handled = Clear Water MATERIAL OF CONSTRUCTION: Impeller = Stainless Steel Pump Shaft = Stainless Steel SS Pump Casing Cast Iron/Stainless steel IMPELLER: Impeller is of the enclosed or semi – enclosed type and properly balanced. Enclosed Impellers equipped with seal rings on their hubs. COUPLING: A suitable coupling arrangement provided with pump set. Non Return Valve: - Non Return Valve of the suitable size provided above the pump discharge case. MOTOR:- Method of starting = Star – Delta Speed = 3000 (Sync). Frequency = 50 ± 3 % Hz Working Voltage = 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Rating = Suitable for above parameters Class of insulation = F/Suitable for above parameters Manufactures Test Certificate to be apended and Detailed specification as per cluase 1 of of SBD Rating: 15 HP |
13 | Fabrication, Providing and fitting of20 HP Modularmotor control panel of appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection Class Detailedspecification as percluase 43 d of SBD |
14 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for Submersible Pumping Unit and other electrical Equipments . The cable connections terminal shall be fitted with copper thimbles of required size. Size: 10 sq.mm |
15 | Providing and Fitting of three/single-Core, copper pvc insulated Cable, XLPE armoured conforming to IS: 7089 part 1st for intedrnal connectionscrimping, taping etc. NOTE:- The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles and of appropriate size and connected by hydraulic crimp tool only. Single core PVC insulated 25sqmm |
16 | 03. (Part A) WSS Gujjar Basti Shangus (Adv. Cost Rs. 37,55,440/-) |
17 | Supply, Installation, Testing & Commissioning of Openwell Horizontal Submersible Pumping Unitas per IS 14220for with following specification are as under : PUMP : Discharge Range = 2000- 4000 GPH Head Range= 65-72 mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump = Open Well HorizontalSubmersible Pump Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 7.50 HP/ as per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clause 3 of SBD Note. Since the source has not been identifiedas yet , as such the above parametres have been assumed and may vary at the time of execution of works depending upon the actual well parametres obtained after identification of Source. |
18 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: DN 65 Class: B (Medium) Rest of Specification/Details areas per clause 7 of SBD |
19 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: DN 65 Class: B (Medium) Rest of Specification as per clause 8 of SBD |
20 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
21 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
22 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
23 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns |
24 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
25 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: DN 65 Class: C Heavy Rest of Specification/Details areas per clause 09 of SBD |
26 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN65 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
27 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 65 mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
28 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
29 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 65 Rest of Specification/Details areas per clause 15 of SBD |
30 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 65 mm Rest of Specification/Details areas per clause 16 of SBD |
31 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
32 | Providing and fitting ofM.S 4 inch hinges -6 no and M.S handle heavy -2no., Anchor bolts with nuts (M16) of 0.3 m long= 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. Rest of Specification/Details areas per clause 23 of SBD |
33 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
34 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 25 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
35 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
36 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
37 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
38 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
39 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
40 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
41 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
42 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
43 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
44 | Providing and Fitting of PG clamps |
45 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
46 | Painting of poles Red oxide |
47 | Painting of poles Aluminum paint |
48 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
49 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
50 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
51 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
52 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 25 KVA Rest of Deatils/Technical specification are as per clause 42 ofSBD |
53 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
54 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G15 and Rest of Deatils/Technical specification are as per clause 43 (c) ofSBD |
55 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::25 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
56 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 45 of SBD. i) 35 sqmm, 3.5core, LTcable |
57 | ii) 10 sqmm, 2 core, LTcable |
58 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 10 sq.mm |
59 | Providing and fitting of 25 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
60 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
61 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
62 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
63 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
64 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
65 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of SBD |
66 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
67 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of SBD |
68 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen . Rest of Deatils/Technical specification are as per clause 55 of SBD |
69 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
70 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
71 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
72 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Details/Technical specification are as per clause 59 of SBD |
73 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
74 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
75 | Providing of 1 KW heat convector for operators for winter season. |
76 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
77 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
78 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 15 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
79 | Providing and fitting of L.T35 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
80 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
81 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
82 | Carriage of sand, stone aggregate by mechanical transportincluding loading, unloadingand stacking (average distance-5km) Rest of Deatils/Technical specification are as per clause 79 of SBD |
83 | 04. (Part A) WSS Bulbul Nowgam(Adv. Cost Rs. 40,75,270/-) |
84 | Supply, Installation, Testing & Commissioning ofOpen Submersible Pumping Unit (verticle ) as per IS 8034for with following specification are as under : PUMP : Discharge Range = 10000-14000 GPH Head Range= 45-60 mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump = OpenwellSubmersible Pump( Verticle ) Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 20.00 HP/as per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clauseof SBD Note. Since the source has not been identifiedas yet , as such the above parametres have been assumed and may vary at the time of execution of works depending upon the actual well parametres obtained after identification of Source. |
85 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: DN 100 Class: B (Medium) Rest of Specification/Details areas per clause 7 of SBD |
86 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: DN 100 Class: B (Medium) Rest of Specification as per clause 8 of SBD |
87 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
88 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
89 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
90 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns |
91 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
92 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: DN 100 Class: C (Heavy) Rest of Specification/Details areas per clause 09 of SBD |
93 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN100 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
94 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 100 mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
95 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
96 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 100 Rest of Specification/Details areas per clause 15 of SBD |
97 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 100 mm Rest of Specification/Details areas per clause 16 of SBD |
98 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
99 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
100 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 63 KVA HT Transformer, 3 phase (Level 2).Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
101 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
102 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
103 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
104 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
105 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
106 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
107 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
108 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
109 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
110 | Providing and Fitting of PG clamps |
111 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
112 | Painting of poles Red oxide |
113 | Painting of poles Aluminum paint |
114 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
115 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
116 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
117 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
118 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 63 KVA Rest of Details/Technical specification are as per clause 42 ofSBD |
119 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
120 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G30 and Rest of Deatils/Technical specification are as per clause 43(e) ofSBD |
121 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::50 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
122 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 50 sqmm, 3.5core, LTcable |
123 | ii) 10 sqmm, 2 core, LTcable |
124 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 16 sq.mm |
125 | Providing and fitting of 50 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
126 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
127 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
128 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
129 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
130 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
131 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting.Rest of Deatils/Technical specification are as per clause 52 of SBD |
132 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
133 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter BatteryRest of Deatils/Technical specification are as per clause 54 of SBD |
134 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen . Rest of Deatils/Technical specification are as per clause 55 of SBD |
135 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
136 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
137 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
138 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Deatils/Technical specification are as per clause 59 of SBD |
139 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
140 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
141 | Providing of 1 KW heat convector for operators for winter season. |
142 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
143 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
144 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 40 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
145 | Providing and fitting of L.T35 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
146 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
147 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
148 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) |
149 | (Part B) Pump House of WSS Bulbul Nowgam(Adv. Cost Rs. 17,91,363/-) |
150 | Earth work in excavation over areas exceeding 30 cm and upto 1.5 m in depth 1.5 m in width as well as 10 sqm on plan inculding disposal of excavated soil upto1mt from cutting edge. All Kinds of Soil |
151 | Extra for every additional lift of 1.5m or part thereoff. |
152 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
153 | Providing and laying of1:4:8 nominal mix cement concrete . |
154 | Reinforced cement concrete of specified grade in 1:1.5:3 nominal mix in Suspended Floors etc |
155 | Centering and shuttering including struting proping and removal of form work. a) Beams, Lintels etc |
156 | b) Suspended Floors, Roofs, Landings etc |
157 | c) Edges of Slabs & breaks in floor walls |
158 | Cement Plaster in 1:3 mix with floating coat of neat Cement. |
159 | 15mm Cement plaster in 1:6 nominal mix. |
160 | Providing Reinforcement to RCC works including bending, binding, cuttingstratining and placing in position complete. |
161 | R.R. Masonary with Quary stone laid in Dry. |
162 | Structural steel works welded in builtup sections, trusses and framed works including cutting, hoisting, fixing in position and applying a priming coat of approved metal primer complete. |
163 | R.R. Masonary with Quary stone laid in 1:6 CM. |
164 | Providing and laying of 50mm thick DPC band over stone work in 1:2:4 nominal mix. |
165 | Pointing on stone work with cement mortar in 1:3 mix. (Flush type) |
166 | Brick work with commonly brunt clay F.P.S bricks of class designation 75 in foundation and plinth in 1:6 CM. |
167 | Extra over Brickwork in super structure upto floor V level. |
168 | Providing and fixing of wooden chowkat in Kail Wood. |
169 | Providing and fixing of 35mm thick glazed shutters for doors and windows of Kail wood. |
170 | Providing and fixing panelled or panelled andglazed shutters for doors and windows 35mm thick of Kail wood. |
171 | Providing and fixing of panelling or penelling and glazing in panelled or panelledand glazed shutters for doors and windows ; penelling 25mm to 40mm thick of Kail wood. |
172 | Providing and fixing of 35mm thick wire guage shutters for doors and windows of Kail wood. |
173 | Providing 50mm thick cement concrete flooring with floating coat of neat cement. |
174 | Providing and fixing 1st quality ceramic glazed tiles with minimum thickness 5mm of approved make like Kajaria, Somany etc. over 12mm thick cement mortar in 1:3 mix. |
175 | Providing & fixing White vitreous china water closet squatting pan (Indian type)along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
176 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
177 | Providing and fixing salem stainless steel kitched sink. Size 610x510x200mm |
178 | Providing and fixing of PVC Waste pipe for sink including PVC waste fitting complete (Felexible 40mm dia = 01 No. |
179 | Providing and fixing of corrogated G.S. Sheets including vertical/curved surfaces with polymer coated J or L hooks (0.50mm thick). |
180 | Providing ridge or hip of width 60cm over all with plain G.S. Sheets fixed with polymer coated J or L hooks (0.50mm thick). |
181 | Providing and fixing plained eaves boarding. 2nd class kail wood(250 x 32 ) |
182 | Supply and fixing rolling shutter of approved make made of required size MS lathes interlocked together through their entire length etc. complete with 80x 1.25 mm M/S Laths with 1.25 mm thick top cover. |
183 | Providing and applying white cement based putty of approved thickness 1mm of approved brand and manufacture over the plastered surfaces to prepare the surface smooth and even complate. |
184 | Distempering with 1st quality acrylic distemper of approvedbrand and manufacture including applyingadditional coats where ever required to achive even shade. (Two Coats) |
185 | Finishing walls with water proofing cement paint of required shade (external) (Snowsum) |
186 | Painting with synthetic enamal paint ofapproved brand and manufacture of required colour to give even shade two or more coats on new work lincludingpriming coat lof approved brand and manufacture. |
187 | Add provision for plumbing, Sanitary, Grills and electricfication to the Quarter (Lumpsum to be paid actual). |
188 | Carriage of material from source to dumping site at road by mechnical transport. a)Cement/ Steel (25 Km) |
189 | b) Sand (40 Km) |
190 | c) 20 mm Aggregate (25 Km)` |
191 | d) 40 mm Aggregate (25 Km) |
192 | e) Stone Solling (10 Km average) |
193 | f) Quarry Stone(20 Km average) |
194 | g) Bricks (Average 20 Km) |
195 | 05. (Part A) WSS Khanpora Kreeri 1st (Adv. Cost Rs. 50,00,550/-) |
196 | Supply, Installation, Testing & Commissioning ofOpen Submersible Pumping Unit (verticle ) as per IS 8034for with following specification are as under : PUMP : Discharge Range = 6000-8000 GPH Head Range= 65-85 mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump = OpenwellSubmersible Pump( Verticle ) Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 20.00 HP/as per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clauseof SBD Note. Since the source has not been identifiedas yet , as such the above parametres have been assumed and may vary at the time of execution of works depending upon the actual well parametres obtained after identification of Source. |
197 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: DN 100 Class: B (Medium) Rest of Specification/Details areas per clause 7 of SBD |
198 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: DN 100 Class: B (Medium) Rest of Specification as per clause 8 of SBD |
199 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
200 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
201 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
202 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns |
203 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
204 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: DN 100 Class: C (Heavy) Rest of Specification/Details areas per clause 09 of SBD |
205 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN100 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
206 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 100 mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
207 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
208 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 100 Rest of Specification/Details areas per clause 15 of SBD |
209 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 100 mm Rest of Specification/Details areas per clause 16 of SBD |
210 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
211 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
212 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 63 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
213 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
214 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
215 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
216 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
217 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
218 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
219 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
220 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
221 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
222 | Providing and Fitting of PG clamps |
223 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
224 | Painting of poles Red oxide |
225 | Painting of poles Aluminum paint |
226 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
227 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
228 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
229 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
230 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 63 KVA Rest of Deatils/Technical specification are as per clause 42 ofSBD |
231 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
232 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G30 and Rest of Deatils/Technical specification are as per clause 43(e) ofSBD |
233 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::50 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
234 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 50 sqmm, 3.5core, LTcable |
235 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. ii) 10 sqmm, 2 core, LTcable |
236 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 16 sq.mm |
237 | Providing and fitting of 50 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
238 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
239 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
240 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
241 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
242 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
243 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of SBD |
244 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
245 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of SBD |
246 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen. Rest of Deatils/Technical specification are as per clause 55 of SBD |
247 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
248 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
249 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
250 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Deatils/Technical specification are as per clause 59 of SBD |
251 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
252 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
253 | Providing of 1 KW heat convector for operators for winter season. |
254 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
255 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
256 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 40 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
257 | Providing and fitting of L.T35 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
258 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
259 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
260 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) |
261 | (Part B) Pump House of WSS Khanpora Kreeri 1st (Adv. Cost Rs. 17,91,363/-) |
262 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed (1 meter from cutting edge) All kinds of soil |
263 | Extra for every additional lift of 1.5 m or part thereof in excavation/ banking excavated or stacked material : All kinds of soil |
264 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
265 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
266 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing & Reinforcement all work up to plinth level (1:1.5:3) 1 cement, 1.5 course sand, 3 graded stone aggregate 20 mm nominal size) |
267 | Centering and shuttering including struting proping and removal of form work. a) Beams, Lintels etc |
268 | b) Suspended Floors, Roofs, Landings etc |
269 | c) Edges of Slabs & breaks in floor walls under 20 cm |
270 | Cement Plaster in 1:3 mix with floating coat of neat Cement. |
271 | 15mm Cement plaster in 1:6 nominal mix. |
272 | Providing Reinforcement to RCC works including bending, binding, cuttingstratining and placing in position complete. |
273 | R.R. Masonary with Quary stone laid in Dry. |
274 | Structural steel works welded in builtup sections, trusses and framed works including cutting, hoisting, fixing in position and applying a priming coat of approved metal primer complete. |
275 | R.R. Masonary with Quary stone laid in 1:6 CM. |
276 | Providing and laying of 50mm thick DPC band over stone work in 1:2:4 nominal mix. |
277 | Pointing on stone work with cement mortar in 1:3 mix. (Flush type) |
278 | Brick work with commonly brunt clay F.P.S bricks of class designation 75 in foundation and plinth in 1:6 CM. |
279 | Extra over Brickwork in super structure upto floor V level. |
280 | Providing and fixing of wooden chowkat in Kail Wood. |
281 | Providing and fixing of 35mm thick glazed shutters for doors and windows of Kail wood. |
282 | Providing and fixing panelled or panelled andglazed shutters for doors and windows 35mm thick of Kail wood. |
283 | Providing and fixing of panelling or penelling and glazing in panelled or panelledand glazed shutters for doors and windows ; penelling 25mm to 40mm thick of Kail wood. |
284 | Providing and fixing of 35mm thick wire guage shutters for doors and windows of Kail wood. |
285 | Providing 50mm thick cement concrete flooring with floating coat of neat cement. |
286 | Providing and fixing 1st quality ceramic glazed tiles with minimum thickness 5mm of approved make like Kajaria, Somany etc. over 12mm thick cement mortar in 1:3 mix. |
287 | Providing & fixing White vitreous china water closet squatting pan (Indian type)along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
288 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
289 | Providing and fixing salem stainless steel kitched sink. Size 610x510x200mm |
290 | Providing and fixing of PVC Waste pipe for sink including PVC waste fitting complete (Felexible 40mm dia = 01 No. |
291 | Providing and fixing of corrogated G.S. Sheets including vertical/curved surfaces with polymer coated J or L hooks (0.50mm thick). |
292 | Providing ridge or hip of width 60cm over all with plain G.S. Sheets fixed with polymer coated J or L hooks (0.50mm thick). |
293 | Providing and fixing plained eaves boarding. 2nd class kail wood(250 x 32 ) |
294 | Supply and fixing rolling shutter of approved make made of required size MS lathes interlocked together through their entire length etc. complete with 80x 1.25 mm M/S Laths with 1.25 mm thick top cover. |
295 | Providing and applying white cement based putty of approved thickness 1mm of approved brand and manufacture over the plastered surfaces to prepare the surface smooth and even complate. |
296 | Distempering with 1st quality acrylic distemper of approvedbrand and manufacture including applyingadditional coats where ever required to achive even shade. (Two Coats) |
297 | Finishing walls with water proofing cement paint of required shade (external) (Snowsum) |
298 | Painting with synthetic enamal paint ofapproved brand and manufacture of required colour to give even shade two or more coats on new work lincludingpriming coat lof approved brand and manufacture. |
299 | Add provision for plumbing, Sanitary, Grills and electricfication to the Quarter (Lumpsum to be paid actual). |
300 | Carriage of material from source to dumping site at road by mechnical transport. a)Cement/ Steel (25 Km) |
301 | b) Sand (40 Km) |
302 | c) 20 mm Aggregate (25 Km)` |
303 | d) 40 mm Aggregate (25 Km) |
304 | e) Stone Solling (10 Km average) |
305 | f) Quarry Stone(20 Km average) |
306 | g) Bricks (Average 20 Km) |
307 | 06. (Part A) WSS Khanpora Kreeri-II (Adv. Cost Rs. 42,83,905/-) |
308 | Supply, Installation, Testing & Commissioning of Open WellVerticle Submersible Pumping Unitas per IS 14220for with following specification are as under : PUMP : Discharge Range = 3000-5000 GPH Head Range= 100- 120 mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump = Openwell Verticle Submersible Pump Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 15.00 HP/ As per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clause 4 of SBD Note. Since the source has not been identifiedas yet , as such the above parametres have been assumed and may vary at the time of execution of works depending upon the actual well parametres obtained after identification of Source. |
309 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: DN 80 Class: B (Medium) Rest of Specification/Details areas per clause 7 of SBD |
310 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: DN 80 Class: B (Medium) Rest of Specification as per clause 8 of SBD |
311 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
312 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
313 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
314 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns |
315 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
316 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: DN 80 Class: C Heavy Rest of Specification/Details areas per clause 09 of SBD |
317 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN 80 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
318 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 80 mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
319 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
320 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 80 Rest of Specification/Details areas per clause 15 of SBD |
321 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 80 mm Rest of Specification/Details areas per clause 16 of SBD |
322 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
323 | Fabrication of gravel Hooper for proper feeding of gravels to the borewell andplatform to bear the load of pumping unit, column pipes etc Rest of Specification/Details areas per clause 22 of SBD i. In stringers , treads , landings etc of stair cases including use of chequered plate wherever required , all complete |
324 | Providing and fitting ofM.S 4 inch hinges -6 no and M.S handle heavy -2no., Anchor bolts with nuts (M16) of 0.3 m long= 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. Rest of Specification/Details areas per clause 23 of SBD |
325 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
326 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 25 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
327 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
328 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
329 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
330 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
331 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
332 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
333 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
334 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
335 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
336 | Providing and Fitting of PG clamps |
337 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
338 | Painting of poles Red oxide |
339 | Painting of poles Aluminum paint |
340 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
341 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
342 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
343 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
344 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 25 KVA Rest of Deatils/Technical specification are as per clause 42 ofSBD |
345 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
346 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G30 and Rest of Deatils/Technical specification are as per clause 43(E) ofSBD |
347 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::30 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
348 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 35 sqmm, 3.5core, LTcable |
349 | ii) 10 sqmm, 2 core, LTcable |
350 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 16 sq.mm |
351 | Providing and fitting of 25 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
352 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
353 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
354 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
355 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
356 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
357 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of SBD |
358 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
359 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of SBD |
360 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen. Rest of Deatils/Technical specification are as per clause 55 of SBD |
361 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
362 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
363 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
364 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Deatils/Technical specification are as per clause 59 of SBD |
365 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
366 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
367 | Providing of 1 KW heat convector for operators for winter season. |
368 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
369 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
370 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 25 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
371 | Providing and fitting of L.T35 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
372 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
373 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
374 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) Rest of Deatils/Technical specification are as per clause 79 of SBD |
375 | (Part B) Pump House of WSS Khanpora Kreeri-II (Adv. Cost Rs. 16,29,793/-) |
376 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed (1 meter from cutting edge) All kinds of soil |
377 | Ordinary Rock |
378 | Extra for every additional lift of 1.5 m or part thereof in excavation/ banking excavated or stacked material : All kinds of soil |
379 | Ordinary Rock |
380 | Providing and laying of dry stone soling tightly hand packed on horizontal levels. |
381 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
382 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
383 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
384 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
385 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts. |
386 | Suspended floors, roofs, landings, balconies and access platform with water proofing ply 12 mm thick |
387 | Edges of slabs and breaks in floors and walls Under 20 cm wide |
388 | 12mm Cement plaster finished with a floating coat of neat cement of mix: 1 : 3 (1 cement : 3 fine sand) |
389 | 1 : 4 ( 1 cement : 4 fine sand) |
390 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate. |
391 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Hot rolled deformed bars |
392 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. ( Welded) |
393 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
394 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
395 | Providing and fixing plained eaves boarding.2nd class kail wood 250x32 mm (nominal size ) |
396 | Providing and fixing of 12 mm thick Ply Board soffit along with supporting of First Class Popular wooden ballies |
397 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class kail wood |
398 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First class kail wood (35 MM THICK) |
399 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class kail wood (35 MM THICK) |
400 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : First class kail wood |
401 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. First class Kail Wood |
402 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick |
403 | P/F of 1st quality ceramic glazed tiles confirming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT,SOMANY,KAJARIA or equivalent make in all colour, shades except bergandy, bottle green, black of any size as approved by Err. incharge in skirting, risers of steps and dados over 12mm thick bed of cement mortor 1:3 (1 cement, 3 coarse samd) and jointing with grey cement slurry @ 3.30 Kgs/SM including pointing in white cement mixed with pigment of matching shade complete. |
404 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown |
405 | P/F salem stainless steel kitched sink sixe 610x510x200 |
406 | R R Masonary with Quary stone laid in 1:6 CM |
407 | R R Masonary with Quary stone laid in dry |
408 | Providing and laying of 50 mm thick DPC band over stone work in 1:2:4 nominal mix |
409 | P/F of PVC Waste pipe for sink incl PVC waste fitting complete |
410 | Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) Flush/Ruled Pointing |
411 | Providing and fixing of PVC/CP sanitary fittings whatever is required at site (Complete Job) |
412 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
413 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
414 | Plumbing and electrfication and iron grills to windows to the quarter (to be Paid actual ) |
415 | Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
416 | Carriage by Mechanical Transport including loading, unloading and stacking Cement and Steel (35 Kms) |
417 | Sand, stone aggregate below 40 mm nominal size (35 Kms) |
418 | Stone aggregate 40 mm nominal size and above ( 35 Kms) |
419 | Stone Soling / Stones(35 Kms) |
420 | Bricks (35 Kms ) |
421 | Carriage by Manual Labour including loading, unloading and stacking Cement(400 m) |
422 | Steel (400 m) |
423 | Sand, stone aggregate below 40 mm nominal size (400 m ) |
424 | Stone aggregate 40 mm nominal size and above ( 400 m ) |
425 | Stone Soling (400 m ) |
426 | Stone Soling (400 m ) |
427 | Bricks (400 m) |
428 | 07. (Part A) WSS Hadipora Pirpora (Regional Watnard) (Adv. Cost Rs. 48,87,555/-) |
429 | Supply, Installation, Testing & Commissioning of Submersible Pumping Unitas per IS 8034for with following specification are as under : PUMP : Discharge Range = 3000-5000 GPH Head Range= 140- 150 mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump =Submersible Pump Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 17.50 HP/ As per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clause 4 of SBD Note. Since the source has not been identifiedas yet , as such the above parametres have been assumed and may vary at the time of execution of works depending upon the actual well parametres obtained after identification of Source. |
430 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: DN 80 Class: B (Medium) Rest of Specification/Details areas per clause 7 of SBD |
431 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: DN 80 Class: B (Medium) Rest of Specification as per clause 8 of SBD |
432 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
433 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
434 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
435 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns |
436 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
437 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: DN 80 Class: C Heavy Rest of Specification/Details areas per clause 09 of SBD |
438 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN 80 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
439 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 80 mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
440 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
441 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 80 Rest of Specification/Details areas per clause 15 of SBD |
442 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 80 mm Rest of Specification/Details areas per clause 16 of SBD |
443 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
444 | Fabrication of gravel Hooper for proper feeding of gravels to the borewell andplatform to bear the load of pumping unit, column pipes etc Rest of Specification/Details areas per clause 22 of SBD i. In stringers , treads , landings etc of stair cases including use of chequered plate wherever required , all complete |
445 | Providing and fitting ofM.S 4 inch hinges -6 no and M.S handle heavy -2no., Anchor bolts with nuts (M16) of 0.3 m long= 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. Rest of Specification/Details areas per clause 23 of SBD |
446 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
447 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 63 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
448 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
449 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
450 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
451 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
452 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
453 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
454 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
455 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
456 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
457 | Providing and Fitting of PG clamps |
458 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
459 | Painting of poles Red oxide |
460 | Painting of poles Aluminum paint |
461 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
462 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
463 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
464 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
465 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 63 KVA Rest of Deatils/Technical specification are as per clause 42 ofSBD |
466 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
467 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G20 and Rest of Deatils/Technical specification are as per clause 43(d) ofSBD |
468 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::30 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
469 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 50 sqmm, 3.5core, LTcable |
470 | ii) 10 sqmm, 2 core, LTcable |
471 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 16 sq.mm |
472 | Providing and fitting of 25 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
473 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
474 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
475 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
476 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
477 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
478 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of SBD |
479 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
480 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of SBD |
481 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen Rest of Deatils/Technical specification are as per clause 55 of SBD |
482 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
483 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
484 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
485 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Deatils/Technical specification are as per clause 59 of SBD |
486 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
487 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
488 | Providing of 1 KW heat convector for operators for winter season. |
489 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
490 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
491 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 40 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
492 | Providing and fitting of L.T35 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
493 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
494 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
495 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) Rest of Deatils/Technical specification are as per clause 79 of SBD |
496 | (Part B) Pump House of WSS Hadipora Pirpora (Regional Watnard) (Adv. Cost Rs. 20,01,750/-) |
497 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed (1 meter from cutting edge) All kinds of soil |
498 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
499 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
500 | 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
501 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing & Reinforcement all work up to plinth level (1:1.5:3) 1 cement, 1.5 course sand, 3 graded stone aggregate 20 mm nominal size) |
502 | Brick work with commonly brunt clay F.P.S bricks of class designation 75 in foundation and plinth in 1:6 CM. |
503 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
504 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. |
505 | Lintel, beams, plinth beams, girders, bressumers and cantilevers |
506 | Suspended floors, roofs, landings, balconies and access platforms. |
507 | Edges of slabs and breaks in floors and walls Under 20 cm wide |
508 | 12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) |
509 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate. |
510 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Hot rolled deformed bars |
511 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
512 | Providing and fixing plained eaves boarding. 2nd class kail wood 250x32 mm (nominal size ) |
513 | Providing foiisting and fixing truesses ,purlins ,raftrs ,posts including cost of sicrrews etc |
514 | Providing and fixing of 20 mm thick ,600 mm wide sofit of firwood specification including jam work |
515 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class kail wood |
516 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First class kail wood (35 MM THICK) |
517 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class kail wood (35 MM THICK) |
518 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : First class kail wood |
519 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
520 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
521 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
522 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick |
523 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
524 | P/F of 1st quality ceramic glazed tiles confirming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT,SOMANY,KAJARIA or equivalent make in all colour, shades except bergandy, bottle green, black of any size as approved by Err. incharge in skirting, risers of steps and dados over 12mm thick bed of cement mortor 1:3 (1 cement, 3 coarse samd) and jointing with grey cement slurry @ 3.30 Kgs/SM including pointing in white cement mixed with pigment of matching shade complete. |
525 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown |
526 | Fabrication providing/fixing MS ladder wherever is required comprising of 50x50x6mm angle iron with chequered plate complete job. |
527 | Filling available excavtedearth (excld. rock) in trenches plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering lead upto 50 m, & lift upto 1.5 m. |
528 | Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) Flush/Ruled Pointing |
529 | Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required. White glazed fire clay kitchen sink of size 600x450x250 mm |
530 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe, 40 mm dia |
531 | Providing and fixing of PVC/CP sanitary fittings incl 50ltrs Gyser(1NO) and 1000 Ltrs PVC Tankwhatever is required at site ( Complete Job) |
532 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
533 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
534 | Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
535 | Fixing of plumbing / Electrification/ Iron Grill to windows including cost of plumbing items/C.P fittings / Conductors/ LED Bulbs/ fans /MCB,etc (Complete Job) |
536 | Carriage By Mechanical Transport including loading, unloading and stacking Cement and Steel (50Kms) |
537 | Sand, stone aggregate below 40 mm nominal size (50 Kms) |
538 | Stone aggregate 40 mm nominal size and above ( 50 Kms) |
539 | Stone Soling (50 Kms) |
540 | Bricks (45 Kms ) |
541 | Extra Carriage By Manual Labour including loading, unloading and stacking Cement(400 m) |
542 | Steel (400 m) |
543 | Sand, stone aggregate below 40 mm nominal size (400 m ) |
544 | Stone aggregate 40 mm nominal size and above ( 400 m ) |
545 | Stone Soling (400 m ) |
546 | Bricks (400 m) |
547 | 08. (Part A) WSS Larnoo Gujjar Basti (Adv. Cost Rs. 44,26,523/-) |
548 | Supply, Installation, Testing & Commissioning ofBore Well Submersible Pump Unitas perIS 8034 with followingspecification as under : PUMP : Rated Dischage = 2000GPH Rated Head = 204 Mtrs Efficiency = Not less than 50% Speed= 2900 Rpm Type of pump = Bore Well Submersible Pump Type of fluid to be handled=Clear Water MOTOR:- Motor Rating= 15HP/As per OEM Method ofstarting = Star – Delta Speed = 3000 (Sync). Frequency= 50 ± 3 % Hz Working Voltage= 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation=F/Suitable for above parameters Rest of Specification/Details are as per clause 1 of SBD |
549 | Fabrication, providing, fitting and lowering ofcolumn pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming toIS: 6392, Table-17 and PN 16 Size: 50 Class:C (Heavy) Rest of Specification/Details areas per clause 7 of SBD |
550 | Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-C confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size: 50 Class:C (Heavy) Rest of Specification as per clause 8 of SBD |
551 | Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) |
552 | Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. |
553 | Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materialin all kinds of soil |
554 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
555 | Centering and shuttering including strutting , propping etc. and removal of form work for Foundation , footings , bases for columns |
556 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) |
557 | Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: 50 Class:C (Heavy) Rest of Specification/Details areas per clause 09 of SBD |
558 | Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN 50 PN:1.6/16 Rest of Specification/Details areas per clause 12 of SBD |
559 | Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 13 of SBD |
560 | Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details areas per clause 14 of SBD |
561 | Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 50 Class: C Rest of Specification/Details areas per clause 15 of SBD |
562 | Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 50mm Rest of Specification/Details areas per clause 16 of SBD |
563 | Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shedwill be provided by Site In Charge at the time of execution of job Rest of Specification/Details areas per clause 21 of SBD |
564 | Fabrication of gravel Hooper for proper feeding of gravels to the borewell andplatform to bear the load of pumping unit, column pipes etc Rest of Specification/Details areas per clause 22 of SBD i. In stringers , treads , landings etc of stair cases including use of chequered plate wherever required , all complete |
565 | Providing and fitting ofM.S 4 inch hinges -6 no and M.S handle heavy -2no., Anchor bolts with nuts (M16) of 0.3 m long= 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. Rest of Specification/Details areas per clause 23 of SBD |
566 | Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity =2 ton Rest of specification as per cluase 24 of SBD |
567 | Creation of pole mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling:ONAN. Rating: 25 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD |
568 | Providing and fittingG.I Channel /Angle/ Flat of sizes including clampsas per details in Clause 27 of SBD |
569 | Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details areas per clause 28 of SBD |
570 | Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gapas per details in Clause 29 of SBD |
571 | Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class as per details in Clause 30 of SBD |
572 | Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD |
573 | Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 ofSBD |
574 | P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 ofSBD |
575 | P/F Danger Plate with clamps as per details in Clause 34 ofSBD |
576 | Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 ofSBD |
577 | Providing and Fitting of PG clamps |
578 | Providing and fitting of Galvanized stay set complete as per details in Clause 36 ofSBD |
579 | Painting of poles Red oxide |
580 | Painting of poles Aluminum paint |
581 | Providing and fitting of ACSR as per details in Clause 39 ofSBD |
582 | Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases:Red, Yellow, Blue |
583 | Providing and fitting of Anchoring clampsrequired for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 ofSBD |
584 | P/F of 11 KV cable termination kit as per details in Clause41 ofSBD |
585 | Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 25 KVA Rest of Deatils/Technical specification are as per clause 42 ofSBD |
586 | Providing and fitting of PRODIGY LT Metre of following specification complete with all fixturesrequired for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium |
587 | Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G20 and Rest of Deatils/Technical specification are as per clause 43(D) ofSBD |
588 | Providing, fitting, testing and commissioning ofManually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::30 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD. |
589 | Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 35 sqmm, 3.5core, LTcable |
590 | ii) 10 sqmm, 2 core, LTcable |
591 | Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964as per details in Clause 47 ofSBD Size: 10 sq.mm |
592 | Providing and fitting of 25 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement. |
593 | Providing and Fitting ofcable tray of suitable size for carrying the cable inside the machinery room. |
594 | P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD |
595 | Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . Rest of details as per specification in clause 49 of SBD |
596 | Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 ofSBD |
597 | Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of SBD |
598 | Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of SBD |
599 | Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Deatils/Technical specification are as per clause 53 of SBD |
600 | Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of SBD |
601 | Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen Rest of Deatils/Technical specification are as per clause 55 of SBD |
602 | TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of SBD |
603 | Providing of good quality conveinence and utility items as per details in Caluse57 of SBD |
604 | Fabricationof7’ (L) x 6’(B) x 1.5" (H) angle iron bedfor operators withback-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Deatils/Technical specification are as per clause 58 of SBD |
605 | Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 3 nos. Rest of Deatils/Technical specification are as per clause 59 of SBD |
606 | Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. |
607 | Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) |
608 | Providing of 1 KW heat convector for operators for winter season. |
609 | Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 63 of SBD |
610 | Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site size= 7x5 feet Rest of Deatils/Technical specification are as per clause 64 of SBD |
611 | Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. Rating: 25 KVA , Air Cooled Manufacturers certifice to be apended and rest of specification as per cluase 66 of SBD |
612 | Providing and fitting of L.T25 Sq. mm , 1core , capable to work upto 1.1 KV, XLPE insulated , galvanized steel strip armoured coppercableconforming to IS : 7089(part -1) 1988 With latest amendmentsto be fitted fromD.G Setto Modular control panel Rest of Deatils/Technical specification are as per clause 67 of SBD |
613 | Providing corrugated G.S Sheet roofingand on the all sides of DG Set shed including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts Rest of Deatils/Technical specification are as per clause 68 of SBD |
614 | Providing, Installation, Testing & Commissioning of complete switchgear unit for protection of D.G Setconsisting of 200A MCCB 3- pole , 415 V, 50 KV breaking capacity Rest of Deatils/Technical specification are as per clause 78 of SBD |
615 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) Rest of Deatils/Technical specification are as per clause 79 of SBD |
616 | Carriage of sand , stone aggregate by mechanical transportincluding loading , unloadingand stacking (average distance-5km) |
617 | Carriage of soling stone by mechanical transportincluding loading , unloadingand stacking (average distance-5km) |
618 | Carriage of cement/steel/CGI sheet/GI pipes below 100mm dia and other heavy materials by mechanicaltransportincluding loading , unloadingand stacking (average distance -25Km) |
619 | (Part B) Pump House of WSS Larnoo Gujjar Basti (Adv. Cost Rs. 20,01,750/-) |
620 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed (1 meter from cutting edge) All kinds of soil |
621 | Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing,ramming, all leads lifts and all carriages complete. |
622 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
623 | 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
624 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing & Reinforcement all work up to plinth level (1:1.5:3) 1 cement, 1.5 course sand, 3 graded stone aggregate 20 mm nominal size) |
625 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
626 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
627 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. |
628 | Lintel, beams, plinth beams, girders, bressumers and cantilevers |
629 | Suspended floors, roofs, landings, balconies and access platforms. |
630 | Edges of slabs and breaks in floors and walls Under 20 cm wide |
631 | 12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) |
632 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate. |
633 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Hot rolled deformed bars |
634 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
635 | Providing and fixing plained eaves boarding. 2nd class kail wood 250x32 mm (nominal size ) |
636 | Providing foiisting and fixing truesses ,purlins ,raftrs ,posts including cost of sicrrews etc |
637 | Providing and fixing of 20 mm thick ,600 mm wide sofit of firwood specification including jam work |
638 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class kail wood |
639 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First class kail wood (35 MM THICK) |
640 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class kail wood (35 MM THICK) |
641 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : First class kail wood |
642 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
643 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
644 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
645 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick |
646 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
647 | P/F of 1st quality ceramic glazed tiles confirming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT,SOMANY,KAJARIA or equivalent make in all colour, shades except bergandy, bottle green, black of any size as approved by Err. incharge in skirting, risers of steps and dados over 12mm thick bed of cement mortor 1:3 (1 cement, 3 coarse samd) and jointing with grey cement slurry @ 3.30 Kgs/SM including pointing in white cement mixed with pigment of matching shade complete. |
648 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown |
649 | Fabrication providing/fixing MS ladder wherever is required comprising of 50x50x6mm angle iron with chequered plate complete job. |
650 | Filling available excavtedearth (excld. rock) in trenches plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering lead upto 50 m, & lift upto 1.5 m. |
651 | Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) Flush/Ruled Pointing |
652 | Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required. White glazed fire clay kitchen sink of size 600x450x250 mm |
653 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe, 40 mm dia |
654 | Providing and fixing of PVC/CP sanitary fittings incl 50ltrs Gyser(1NO) and 1000 Ltrs PVC Tankwhatever is required at site ( Complete Job) |
655 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
656 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
657 | Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
658 | Fixing of plumbing / Electrification/ Iron Grill to windows including cost of plumbing items/C.P fittings / Conductors/ LED Bulbs/ fans /MCB,etc( Complete Job) |
659 | Carriage By Mechanical Transport including loading, unloading and stacking Cement and Steel (50Kms) |
660 | Sand, stone aggregate below 40 mm nominal size (50 Kms) |
661 | Stone aggregate 40 mm nominal size and above ( 50 Kms) |
662 | Stone Soling (50 Kms) |
663 | Bricks (45 Kms ) |
664 | Extra Carriage By Manual Labour including loading, unloading and stacking Cement(400 m) |
665 | Steel (400 m) |
666 | Sand, stone aggregate below 40 mm nominal size (400 m ) |
667 | Stone aggregate 40 mm nominal size and above ( 400 m ) |
668 | Stone Soling (400 m ) |
669 | Bricks (500 m) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail