Bids Are Invited For Supply Of Godrej Make 900Mm ( W ) X507mm ( D ) X1950mm ( H ) ( Height Without Leveler ) . Construction & Material-Aesthetically Appealing Slimline, Completely Knock Down Construction. Removable Skirting To Cover Integral Legs. Leg, Hyderabad-Telangana

Bids Are Invited For Supply Of Godrej Make 900Mm ( W ) X507mm ( D ) X1950mm ( H ) ( Height Without Leveler ) . Construction & Material-Aesthetically Appealing Slimline, Completely Knock Down Construction. Removable Skirting To Cover Integral Legs. Legs Fitted With Screw Type Leveler Made From Combination Of Crca 0.8 Mm & 0.6 Mm Thickness. Main Door Steel Hinged Door. Main Door Locking / Handle: Handle & Base Aesthetically Appealing, Ergonomic, Flush With Door Made From Zinc Alloy. 3 Way 90 Degree Removable Key Type Cam Lock & Locking Mechanism. Locker Door & It’S Locking / Handle For Model ‘H’ .Fixed Half Locker On Rh Side Hinged Door 2 Way Cam Lock With Knob Type Handle Shelving: Model 4S Height Wise Adjustable Shelf Mounting 4 Nos. Of Full Adj.Shelves Model 2Sh Height Wise Adjustable Shelf Mounting 2 Nos. Of Full Adj.Shelves • Locker Model ‘H’ – Top Fixed Full Shelf Adjustable Half Shelves – 1 No. On Rh & 2 Nos. On Lh Side Of Vertical Partition. Hanging Rod Model 2Sh 1 No. Full Length Hanging Rod Below Top Shelf Mounted On Snap-On Type Plastic Brackets. Locker Model ‘H’  2 Nos. Half Length Hanging Rods – One On Left Half Of Partition Below Top Shelf & Another On Right Half Below Locker – Both Mounted On Snap-On Type Plastic Brackets 9. Finish:  Epoxy Powder Coated To The Thickness Of 50 Microns ( +-10 ) . 20 Sline Minor 2S Body Royal Ivory Godrej Make Product Size:900Mm ( W ) X 507Mm ( D ) X 1372Mm ( H ) ( Height Without Leveler ) . Construction & Material: Aesthetically Appealing Slim Line, Completelyknock Down Construction.Removable Skirting To Cover Integral Legs. Legs Fitted With Screw Type Leveler .Made From Combination Of Crca 0.8 Mm & 0.6 Mm Thickness. Main Door  Steel Hinged Door. Shelves  2 Shelves For Slimline Minor. Completely Adjustable Over The Total Height Of The Cupboard. Main Door Locking / Handle: Handle & Base Aesthetically Appealing, Ergonomic, Flush With Door Made Of Mazak . 3 Way 90 Degree Removable Key Type Cam Lock & Locking Mechanism. Finish:  Epoxy Powder Coated To The Thickness Of 50 Microns ( +-10 ) . 45 Finnesse Table5630+Fin Nesse Eru5216 Lhs+Ped Estal Godrej Make Finesse Table - 5630 Size Shall Be 1650 Width Mm X 900 Depth Mm X 740 Height Mm .Table Top Shall Be 25 Mm Thick Plain Particle Board ( Ppb ) Clad With 0.6 Mm Thick Post Formed Laminate And 1 Mm Thick Backing Laminate ( Bdl ) .Flat Edge Duly Sealed With 2 Mm Thick Pvc Beading.The Modesty Shall Be 18 Mm Thick Plain Particle Board ( ) Ppb Clad With 1.0 Mm Thick Decorative Laminate ( Dl ) On Both Sides. Edge Sealed With 2 Mm Thick Pvc Beading. Finesse Eru -5216 Lhs Size Shall Be 1550 Width X 450 Depth X 705 Height.The Top Of Finesse Eru -5216 Lhs Shall Be 25 Mm Thick Plain Particle Board ( Ppb ) Clad With 0.6 Mm Thick Post Formed Laminate And 1 Mm Thick Backing Laminate ( Bdl ) .Flat Edge Duly Sealed With 2 Mm Thick Pvc Beading. The Modesty Shall Be 18 Mm Thick Plain Particle Board ( Ppb ) Clad With 1.0 Mm Thick Decorative Laminate ( Dl ) On Both Sides. Edge Sealed With 2 Mm Thick Pvc Beading. Free Standing Nova Pedestal 45 Premier High Back Godrej Make Seat / Back Assembly: The Seat And Back Should Be Made Up Of 1.2 ±0.1Cm. Thick Hot Pressed Plywood And Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Should Be Designed With Contoured Lumbar Support For Extra Comfort. Back Size 49.0 Cm. ( W ) X 71.0 Cm. ( H ) Seat Size 49.0 Cm. ( W ) X 44.0 Cm. ( Id ) High Resilience ( Hr ) Polyurethane Foam: The Hr Polyurethane Foam Should Be Moulded With Density = 45 ±2 Kg / M3 And Hardness Load 16 ± 2 Kgf For 25% Compression. Armrests: The Armrest Tops Should Be Injection Moulded From Black Polypropylene. They Should Be Fitted To Tubular Armrest Supports Made Of Ø2.54 ±0.03Cm. X 0.16 ±0.0128Cm.Thk. M.S. E.R.W. Tube And Black Powder Coated ( Dft 40-60 Microns ) . The Tubular Armrest Supports Hold Together The Seat And Back. Center Tilt Mechanism: The Mechanism Should Be Designed With The Following Features: • 360° Revolving Type. • 17° ±2° Maximum Tilt On Pivot At Center • Upright Position Locking. • Tilt Tension Adjustment. Pneumatic Height Adjustment:The Pneumatic Height Adjustment Has An Adjustment Stroke Of 11.0 ±0.3Cm..Twin Wheel Castors:The Twin Wheel Castors Should Be Injection Moulded In Black Nylon.Telescopic Bellow Assembly:The Bellow Should Be 3 Piece Telescopic Type And Injection Moulded In Black Polypropylene. Pedestal Assembly:The Pedestal Should Be Fabricated From 0.2 ± 0.02 Cm Thick Hr Sheet , Powder Coated ( Dft 40-60 Microns ) And Fitted With An Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors. The Pedestal Should Be 60.0 ±0.5Cm. Pitch-Centre Dia. ( 70.0 ±1.0 Cm. With Castors ) . 45 Premier Visitor With Armrest Godrej Make Seat / Back Assembly: The Seat And Back Should Be Made Up Of 1.2 ±0.1Cm. Thick Hot Pressed Plywood And Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Should Be Designed With Contoured Lumbar Support For Extra Comfort. Back Size 49.0 Cm. ( W ) X 47.0 Cm. ( H ) Seat Size 49.0 Cm. ( W ) X 44.0 Cm. ( D ) High Resilience ( Hr ) Polyurethane Foam: The Hr Polyurethane Foam Should Be Moulded With Density = 45 ±2 Kg / M3 And Hardness Load 16 ± 2 Kgf For 25% Compression. Armrests: The Armrest Tops Should Be Injection Moulded From Black Polypropylene. They Should Be Fitted To Tubular Armrest Supports Made Of Ø2.54 ±0.03Cm. X 0.16 ±0.0128Cm.Thk. M.S. E.R.W. Tube And Black Powder Coated ( Dft 40-60 Microns ) . The Tubular Armrest Supports Hold Together The Seat And Back. Tubular Frame: The Tubular Frame Should Be Cantilever Type & Made Of Ø2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. M.S. E.R.W. Tube And Black Powder Coated ( Dft 40-60 Microns ) . Overall Dimensions Of Chair-Seat Height - 43.0 Height - 80.0Cm. Width & Depth Of Chair As Measured From Pedestal - Width-55 Cm And Depth-61.0 Cm. 135 Esd Table Antistatic Table Aluminium Welded Esd Workstation With Aluminium Profile Size Table Top 750Wx1500lx 850H Mm Godrej Make Enterprise 1650 Table Without Cpu Hanger Size Shall Be 1650 Width X 9000 Depth X 728 Height . Top Shall Be 18 Mm Thick Pre Laminated Particle Board All Work Surface Edges Shall Be Having Duly Sealed With 2 Mm Thick Pvc Edgebanding. Understructure Modesty Panel 18 Mm Thick Pre Laminated Particle Board . The Rectangular Frame Shall Be Fabricated Component In 1.2 Mm Thick Crca , Finish : Powder Coat ( Epoxy Polyster ) . Leg Shall Be Fabricated Component In 38 Mm X 25 Mm 1.2 Mm Thick Ms Erw Atube , Finish Powder Coat ( Epoxy Polyster ) .The Plastic Cap For Cable Travel Shall Be Injection Moulded Polypropylene And Leveler Glide For Shall Be Nylon 6 & Ms Bolt. The Storage Shall Be Having Shell And Drawer Tray 0.6 Mm Thick Crca Finish Powder Coat ( Epoxy Polyster ) Plus The Drawer Front Shall Be 0.8 Mm Thick Crca Finish Powder Coat ( Epoxy Polyster ) Plus Lock With 10 Lever And Handle And Leveller. The Wire Management Shall Be Horizontal Wire Carrier 0.7 Mm Thick Crca Finish Powder Coat ( Epoxy Polyster ) And Vertical Wire Carrier 0.8 Mm Thick Crca Finish Powder Coat ( Epoxy Polyster ) . 15 Econom Y Executi Ve ( Eii ) Mid Back Godrej Make 1. Seat / Back Assembly: The Seat And Back Should Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood And Upholstered With Changeable Fabric Upholstery Covers And Moulded Polyurethane Foam, Together With Moulded Back-Spine Cover. The Back Foam Should Be Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 42.0Cm. ( W ) X 46.0Cm. ( H ) Seat Size: 47.0Cm. ( W ) X 50.0Cm. ( D ) 2. High Resilience ( Hr ) Polyurethane Foam : The Hr Polyurethane Foam Should Be Moulded With Density = 45 + / -2 Kg / M3 And Hardness Load 16 ± 2 Kgf For 25% Compression. 3. Armrests: The Armrests Should Be Made Of Black Integral Skin Polyurethane Wtih 50-70 Shore A Hardness And Reinforced With M.S. Insert. The P.U. Armrests Should Be Then Fixed To Black Powder-Coated ( Dft 40-60 Microns ) Armrest Brackets Made Of Of 0.5 ± 0.05 Cm. Thk. Hr Steel And Fitted With Claddings Made Of Injection Moulded Polypropylene. 4. Permanent Contact Mechanism: The Permanent Contact Mechanism Should Be Designed With The Following Features: 360° Revolving Type. 14°±2° Maximum Back-Tilt Only. Upright Position Locking. Tilt Tension Adjustment. 5. Spine Cover: The, Spine Cover Should Be Injection Moulded In Black Co-Polymer Polypropylene. 6. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 12.0±0.3 Cm. 7. Telescopic. Bellow Assembly: The Bellow Should Be 3 Piece Telescopic Type And Injection Moulded In Black Polypropylene. 8. Pedestal Assembly: The Pedestal Should Be Fabricated From 0.2 ± 0.02 Cm Thick. Hr Sheet ( Should Be :Dd 10791 Hr ) , Powder Coated ( Dft 40-60 Microns ) And Fitted With An Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors. The Pedestal Should Be 60.0 ±0.5Cm. Pitch-Centre Dia. ( 70.0±1.0 Cm With Castors ) . 9. Twin Wheel Castors: The Twin Wheel Castors Should Be Injection Moulded In Black Nylon. 45 White Board White Marker Board Size 6X4 Ft Ceramic Steel White Dry Erase Writing Board With Following Dimensions. I ) Width 1800Mm Ii ) Height 1200Mm Iii ) Wall Thickness Of Anodized Amuminium Frame - 1.2 Mm Iv ) Frame Width - 20Mm

Refer document

Refer document

Refer document