Construction Ofhelipad At Kohla In Tehsil Nadaun District Hamirpur ( H.P. ) . ( Sh:- C / O Building Portion, C / O Helipad Launch Pad And Take Off Pad, C / O Road By Laying Gsb, Wmm, Bm, Bc, Stud, Road Marking, Retaining Wall And Crate Work ) .
Tender Value
1.20 Crore
Estimated cost
Bid Submission
14 Jul 2022
0 days left
EMD
1.53 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
hamirpur → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Ofhelipad At Kohla In Tehsil Nadaun District Hamirpur ( H.P. ) . ( Sh:- C / O Building Portion, C / O Helipad Launch Pad And Take Off Pad, C / O Road By Laying Gsb, Wmm, Bm, Bc, Stud, Road Marking, Retaining Wall And Crate Work ) .
BOQ
| Sl. No. | Item Description |
| 1 | Excavation workby mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains for all kinds of soil and ordinary rocks including dressing of sides and ramming of bottoms andback filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm (one hundred fifty millimetre) compacted thicknessincluding shoring and strutting and pumping and bailing out water (surface and sub soil water) upto all depth and any quantum of waterincluding cleaning of slush which may arise out during dewatering upto all lifts including getting out the excavated soil and disposal of surplus excavated soil as directedincluding entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 2 | Excavating trenches of required width for pipes, cables, etcetera including excavation for sockets, and dressing of sides, ramming of bottoms, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within all leads for Pipes, cables etcetra for all diametre not exceeding 300 mm (three hundred millimetre) diametreincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form work for including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 5 | Foundations, footings, bases for columns. |
| 6 | Suspended floors, roofs, landings, balconies and access plat form |
| 7 | Walls (any thickness) including attached pillasters, butteresses, plinth and string courses etc. |
| 8 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 9 | Edges of slab and break in floors and walls under 20cm ( Twenty centimetre) wide. |
| 10 | Providing and laying in position cement concrete of specified grade1:5:10 (one cement : five coarse sand : ten graded stone aggregate) 40mm ( forty millimetre)nominal size graded stone aggregate in retaining wall, breast wall, walls of any thickness and like structures excluding the cost of centering and shutteringincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering1:4:8 (one cement : four coarse sand : eight graded stone aggregate) 40mm ( forty millimetre)nominal size graded stone aggregate upto plinth level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering 1:3:6 (one cement : three coarse sand : six graded stone aggregate) 40mm ( forty millimetre)nominal size graded stone aggregate upto plinth level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 13 | Providing and laying in position cement concrete of 1:2:4 (One cement : Two coarse sand) : four graded stone aggregate 20 mm (Twenty millimetre) nominal size) size) for all work up to plinth levelexcluding the cost of centering and shuttering, finishing and reinforcement including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 14 | Providing and laying damp-proof course 40mm ( forty millimetre) thick with cement concrete 1:2:4 ( one cement : two coarse sand : four graded stone aggregate 12.5mm ( twelve point five millimetre) nominal size including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 15 | Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg ( one point seven kilogram )per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oilincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 16 | Providing and layingmechanically mixed and vibrated design mix reinforced cement concrete ofM-25 (twenty five ) grade, stone aggregate 20 mm (twenty millimetre) nominal size) with minimiumcement content not less than 400Kg ( four hundred kilogram) per cubic metreexcluding the cost of centering, shuttering, finishing and reinforcement upto plinth level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 17 | Providing and layingmechanically mixed and vibrated design mix reinforced cement concrete ofM-25 (twenty five ) grade, stone aggregate 20 mm (twenty millimetre) nominal size) with minimiumcement content not less than 400Kg ( four hundred kilogram) per cubic metre in beams, suspended floors, roofs having slope up to 15° ( fifteen degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, stair cases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 18 | Providing and layingmechanically mixed and vibrated design mix reinforced cement concrete ofM-25 (twenty five ) grade, stone aggregate 20 mm (twenty millimetre) nominal size with minimiumcement content not less than 400Kg ( four hundred kilogram) per cubic metrein walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etcetera above plinth level up to all floor level, excluding cost of centering, shuttering, finishing and reinforcement including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 19 | Providing and layingmechanically mixed and vibrated design mix reinforced cement concrete ofM-25 (twenty five ) grade, stone aggregate 20 mm (twenty millimetre) nominal size with minimiumcement content not less than 400Kg ( four hundred kilogram) per cubic metreinstring courses, bands, copings, bed plates, anchor blocks, plain window sills and the like upto up to all floor level, including cost of centering, shuttering, finishing, excluding cost of reinforcement including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 20 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm(six millimetre) thick cement mortar 1:3 (one Cement : three fine sand).including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 21 | Steel reinforcement (TATA /SAIL / JINDAL PANTHER/ Shyam steelmake)for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete work including cost of binding wire upto all floor level mild steel and medium tensile steel bars of grade Fe-500D or more including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 22 | Steel work in built up tubular (TATA/SAIL/APPOLLO MAKE) (round, square or rectangular hollow tubes etc.) trusses, railings/ hand rail and other similar frame work etcetra including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etcetera Hot finished welded type tubes completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 23 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five)in foundation and plinth in Cement mortar 1:6 (one cement :six coarse sand) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five)in foundation and plinth in Cement mortar 1:4 (one cement :four coarse sand) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 25 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in super structure above plinth level up to all floor level in all shapes and sizes Cement mortar 1:6 (one cement : six coarse sand) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 26 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in super structure above plinth level up to allfloorlevel in cement mortar 1:4 ( one cement : four coarse sand)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 27 | Random rubble masonry / polygonal uncoursed/ brought to courses with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 ( one cement: six coarsesand : twelve graded crushed stone aggregate ) 20mm ( twenty milimetre ) nominal size upto plinth level in cement mortar 1:6 ( one cement: six coarsesand )including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 28 | Providing and laying hard stone for soling under floor andpitching work22.5cm(twenty two point five centimetre) thick at site including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 29 | Providing and fixing Cup Board Shutters 25 mm ( twenty five millimetre)thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board (HD HMR) IS: 12823 marked ofAction TESA / Green Ply/ Kit Ply/ Century Ply make exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm (twenty five millimetre) wide x12 mm ( twelve millimetre)thick with necessary screws and bright finished stainless steel piano hinges, complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 30 | Providing and fixing 18mm (Eighty millimetre) Pre-laminated flat pressed three layer (HDHMR) particle board or graded wood particle board IS : 3087 marked ofAction TESA / Green Ply/ Kit Ply/ Century Ply make with one side decorative and other side balancing lamination Grade I, Type II interior grade IS : 12823 marked in Shelves with screws and fittings wherever required, edges to be painted with polyurethane primer including all fittings complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 31 | Providing and fixing 1.00 mm ( one millimetre) thick decorative high pressure Laminated SheetofGreenlam/ Century ply / Kit ply make plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 32 | Providing and fixing 2nd class teak wood lipping/ moulded beading or Taj beading of size 18X5 mm (eighteen into five millimetre) fixed with wooden adhesive ofapproved quality and screws/nails on the edges of the Pre-laminated particle boardcomplete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 33 | Providing Second class Teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length complete upto all floor level including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Chargeincluding other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 34 | Providing 40x5mm (forty into five) millimetre flat iron hold fast 40 cm (forty) centimetre long including fixing to frame with 10mm (ten) millimetre diametre bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm (thirty into ten into fifteen centimetre)1:3:6 mix (one cement : three sand : six graded stone aggregate 20mm (twenty) millimtres complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 35 | Providing and fixing 35 mm (Thirty five millimetre) thickSecond class teak wood Glazed Shutters for doors, windows and clerestory windows using 4 mm (Four millimetre) thick float glass panes of ModiguardSaint Gobain, Asahi make(weight not less than 10kg/sqm (ten kilogram per square metre) including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 36 | Providing and fixing 35 mm (thirty five) thick Second class teak wood Wire Gauge Shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm( one point fourmillimetre) in both directions with wire of dia 0.63 mm,(zero point sixty three millimetre) for doors, windows and clerestory windows with hinges and necessary screws with ISI marked Stainless Steel butt hinges of required size all complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 37 | Providing and fixing 35 mm thick ISI marked Flush Door Shuttersconforming to IS : 2202 (Part I) of Century Ply/ Kit Ply/ Green Ply/ Action Tessa make ,decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 38 | Providing and fixing M.S. grills of approved pattern in frames of windows etcetra with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed tosteel window/ wooden frame bywelding/ rawl plugs/ screw etcetra upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 39 | Providing and fixingFloat glass panes of nominal thickness 5 mm ( five millimetre)make of Modiguard,Saint Gobain, Asahi (weight not less than 12.5kg/sqm (twelve point five kilogram per square metre) of renewing glass paneswith putty and nails wherever necessary including racking out the old putty complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 40 | Providing and fixing 300x16 mm (Three hundred into sixteen millimetre) nominal size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetra. complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 41 | Providing and fixing 250x16 mm (Two hundred fifty into sixteen millimetre) nominal size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetra. complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 42 | Providing and fixing 200x10 mm (Two hundred into ten millimetre) nominal size. aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetracomplete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 43 | Providing and fixing 150x10 mm (One hundred fifty into ten millimetre) nominal size aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetracomplete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 44 | Providing and fixing100x10 mm (One hundred into ten millimetre) nominal size aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetracomplete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 45 | Providing and fixing 125 mm (One hundred twenty five millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 46 | Providing and fixing 100 mm (one hundred millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 47 | Providing and fixing 75 mm (seventy five millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 48 | Providing and fixing chromium plated brass 50 mm ( fifty millimetre) Cupboard or Wardrobe Knobs/Handlesof Link/Godrej/Hettich make with nuts complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 49 | Providing and fixing 40 mm ( fortymillimetre)special quality bright finished Cupboard or Wardrobe locks of Link/Godrej makewith four levers of approved quality including necessary screws etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 50 | Providing and fixing 150 mm ( one hundred fifty millimetre) bright finished floor Brass Door Stopper with rubber cushion, necessary brass screws etcetra to suit shutter thickness completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 51 | Providing and fixing bright finished brass hard drawn hooks and eyes 150 mm(one hundred fifty millimetre) completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 52 | Providing and fixing 25mm ( twenty five millimetre) diachromium plated brass Curtain Rod withKnobs at endshaving wall thickness of 1.25mm ( one point two five millimetre)with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etcetra wherever necessary complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 53 | Providing and fixing Triple strip vertical type magnetic catcher of approved quality (Hettich/Godrej) in cupboard / ward robe shutters, including fixing with necessary screws etcetra completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 54 | Providing and fixing ( one hundred fifty ) bright finished brass hasp and staple (safety type) with necessary screwset etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 55 | Providing and fixing 2mm (Two millimetre) thck PVC antistatic venyl flooring plain or coloured, carbed or mosaic/metalled finish ( Wonderfloor/ LG make)laid with approved adhseive on sub-floor (damp proofing treatment to be paid for separately) complete upto all floor level in all heights including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 56 | Providing and laying 18 mm (Eighteen millimetre) thick Polished Granite stone slab (Jet Black, Cherry Red, Elite Brown, Cat Eye colour) in flooring,steps with three grooves (Single Slab), risers Single slab), kitchen shelves in required design and patterns, in linear as well as curvilinear portions of the building all complete including nozing and moulding as per the architectural drawings over 20 mm (Twenty millimetre) (average) thick base of cement mortar 1:4 (One cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etcetera all complete as specified and as directed by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 57 | Extra for pre finished nosing in treads of steps of Marble/Kota stone/Granite stone slab complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 58 | Providing and laying600x600 mm ( six hundred into six hundred millimetre) Full Body Charged Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( zero point zero eight percent)and conforming to IS: 15622, of Orient bell/ Kazaria/ AGL/ RAK /Johnson and Johnson approved make, in all colours and shades, laid on 20mm ( twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm(Three point three kilogramme per square metre) including grouting the joints with white and matching pigment etcetra complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 59 | Providing and laying600x600 mm ( six hundred into six hundred millimetre) Full Body Charged Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( zero point zero eight percent)and conforming to IS: 15622, of Orient bell/ Kazaria/ AGL/ RAK /Johnson and Johnson approved make, in all colours and shades,, in skirting, riser of steps,with cement bases high polymer modified quick set tile adhesive ( water based) conforming to IS:15477 in average 6mm (six millimetre)thickincluding groutingthe joints with white cement and matching pigments etc., complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 60 | Providing and laying VitrifiedFloor Tiles of size 300x300x 9.8 mm (Three hundred into three hundred millimetre into nine point eight millimetre) or more millimetre)of 1st quality conforming to IS : 15622, of Orient bell/ Kazaria/ AGL/ Rak/ Johnson and Johnson approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick Cement Mortar 1:4 (one Cement : four Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm (three point three kilogramme per square metre) including groutingthe joints with white cement and matching pigments etcetera, complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 61 | Providing and fixing 1st quality HD series Digital Glazed rectifiedceramic tiles (300mmx600 mm size) ( Three hundred into six hundred millimetre)conforming to IS : 15622 (thickness to be specified by the manufacturer ) of Orient bell/ Kazaria/ Rak/Johnson and Johnson make , in all colours, shades except burgundy, bottle green, blackas approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm ( twelve millimetre )thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm ( three point three kilogram per square metre) including pointings in white cement mixed with pigment of matching shade complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 62 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishingetcetra complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government |
| 63 | size 500x500 mm(fivehundred into five hundred millimetre) or below |
| 64 | size 600x600 mm(sixhundred into six hundred millimetre) |
| 65 | Providing and laying factory made Pre polished 60mm thick cement concrete paver block of M-40 ( M-forty ) grade with approved Make of NTC/MODERN (DELHI)/NITCO/GICO,chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etcetera of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick ( fifty millimetre) compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge , colour, design and patternincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 66 | Providing and fixing 110mm ( one hundred ten millimetre)dia of Supreme/Fenolax/ Vectus make unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etcetra complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 67 | Providing and fixing Single socketed pipes 110mm ( one hundred ten millimetre)dia of Supreme/Fenolax/Vectus make on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimetre)gap for thermal expansion complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 68 | Applying priming coat With ready mixed pink or Grey primer(ASAIN/NEROLAC/ICI-DULUX)of approved brand and manufacture on wood work (hard and soft wood) Ready mixed paint brushing with whitelead for priming including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 69 | Painting wood work with Deluxe Multi Surface Paint of required shade withTwo or more coat applied @ 0.90 ltr/10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @0.75 ltr/10 sqm (at the rate of zero point seven five litre per ten square metre)(ASAIN/NEROLAC/ICI-DULUX ) of approved brand and manufacture complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 70 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm(at the rate of zero point eight zero litre per ten square metre)of approved brand and manufacture ( ASAIN/NEROLAC/ICI-DULUX ) complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 71 | Polishing on New wood work with ready mixed wax polish of approved brand and manufactureincluding preparing the surface by rubbing and sand papering to give smooth finish complete and including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 72 | 6 mm (six millimetre) plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved makeupto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 73 | 15 mm ( fifteen millimetre)cement plaster onrough sides of single or half brick wall of mix 1:6 ( one cement : six coarse sand)upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 74 | 15 mm ( fifteen millimetre)cement plaster onrough sides of single or half brick wall of mix 1:4 ( one cement : four coarse sand)upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 75 | 20 mm (twenty millimetre) cement plaster of mix 1:6 ( one cement : six coarse sand) on rough side brick wall upto all floor levelas per approved drawing and as per directions of Engineer-in-charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 76 | 20 mm (twenty millimetre) cement plaster of mix 1:4 ( one cement : four coarse sand) on rough side brick wall upto all floor levelas per approved drawing and as per directions of Engineer-in-charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 77 | Providing and applying white Cement Based Putty of average thickness 1 mm ( one millimetre)of approved brand and manufacturer ( J K White/ Birla White ) over the plastered wall surface to prepare the surface even and smooth complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 78 | Distempering with Oil Bound Washable Distemper of approved brand and manufacture to give an even shade on new work (two or more coats) over and including water thinnable priming coat with cement primer of ASIAN/NEROLAC/ICI-DULUXcomplete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 79 | Finishing walls with Acrylic Smooth Exterior Paint of ASIAN- APEX ULTIMAof required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm ( at the rate of one point six seven litre per ten square metre)over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm ( at the rate two point two zero kilogram per ten square metre) complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 80 | Making plinth protection 50mm ( fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm ( twenty millimetre)nominal size) over 75mm( seventy five millimetre)thick bed of dry brick ballast 40 mm ( forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling and dressing and finishing the top smooth including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 81 | Steel work welded in built up sections(TATA/ SAIL/ Apollo/ JSW/ JAI BHARAT Make ) in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etcetra as required in gratings, door & window frames, guard bar, ladder, railings, brackets, gates and similar works complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 82 | Making khurras 45x45 cm (forty five into forty five centimetre) with average minimum thickness of 5 cm (five centimetre)cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate of 20 mm(twenty millimetre)nominal size) over P.V.C. sheet 1 m(one metre) x1 m(one metre) x 400 (four hundred)micron, finished with 12 mm(twelve millimetre) cement plaster 1:3 (one cement : three coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 83 | Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm (Zero point four zero per square metre), 2nd (Second), 4th (Fourth) & 6th (Sixth) courses of bonding material @ 1.20 Kg/sqm (One point two zero kilogramme per square metre), which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd (Third) and 5th (Fifth) layers of roofing membrane APP modified Polymeric membrane 1.5 mm (One point five millimetre) thick of 2.25 Kg/sqm (Two point two five kilogramme per square metre) weight consisting of five layers prefabricated with centre core as 20 (Twenty) micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 (Twenty) micron HMHDPE film. 7th (Seventh), the top most layer shall be finished with brick tiles of class designation 10 (Ten) grouted with cement mortar 1:3 (One cement : three fine sand) mixed with 2% (Two percent) integral water proofing compound by weight of cement over a 12 mm (Twelve millimetre) layer of cement mortar 1:3 (one cement : three fine sand) and finished neat (item of laying brick tiles shall be paid for separately) complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 84 | WATER SUPPLY AND SANITARY INSTALLATION |
| 85 | Providing and fixing White Vitreous China Single Piece Water Closet with PP soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings of Size : 360x725x735mm (Three hundred sixty into seven hundred twenty five into seven hundred thirty five millimetre) S-Trap 300mm (Three hundred millimetre) of Jaquar with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 86 | Providing and fixing White Vitreous China wash basin (CNS-WHT-801)ofSize (mm) 550x400x415 (Five hundred fifty into four hundred into four hundred fifteen millimetre) with C.I. brackets, 15 mm (Fifteen millimetre) CP Brass single hole basin mixer of Jaquar (CON-CHR-167B) / Hindware 32mm (thirty two millimetre)C.P. brass waste of standard pattern , including painting of fittings and brackets, cutting and making good the walls wherever required including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 87 | Providing and fixing white Vitreous Chinafull pedestal (ARS-WHT-39301 of Jaquar)for wash basin completely recessed at the back for the reception of pipes and fittings of Hindware/ Jaquar / Cera make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 88 | Providing and fixing P.V.C. waste semi rigidpipe for sink or wash basin including P.V.C. wastefittings complete of 32mm ( thirty two millimetre)dia of Supreme /Fenolaxmakeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 89 | Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre)beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre)thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete of ( Modigaurd/ Atul/Cera/Exotica make)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 90 | Providing and fixing Stainless Steel towel rail of Jaquar (ACN-CHR-1111SM) complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm ( six hundred millimetre)long including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 91 | Providing and fixing 600 mm ( six hundred millimetre) long Glass Shelf of Jaquar( ACN-CHR-1171N)supportedwith C.P. brass brackets and other acessoriescomplete fixed with 40 mm ( forty millimetre)long screws, rawl plugs etcetra, completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 92 | Providing and fixing CP soap Dish Holder of Jaquar ( ACN-CHR-1131N ) with concealed fitting arrangements including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 93 | Providing and fixing 15mm ( fifteen millimetre)dia Short body C.P. Brass BibCock with wall flange of approved quality conforming to IS:8931of Jaquar ( CON-047KN) make conforming to IS standards including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 94 | Providing and fixing 15mm ( fifteen millimetre)dia Long body C.P. brass bibcock with wall flange of approved quality conforming to IS:8931of Jaquar ( OPP-15037PM) make conforming to IS standards including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 95 | Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. brass Stop Cock of Jaquar ( CON-059 KN )with wall flange for basin mixer and geyser points of approved quality conforming to IS:8931including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Chargeincluding other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 96 | Providing and fixing 450mm Long Braided Hose with Two 15mm Nuts & Rubber Washers Without Nipple (Suitable for Geysers)ofCera/ Jaquar (ALD-805B) / Finolex / Hindware Makeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 97 | Providing and fixing 15mm (Fifteen millimetre) size Ball Valve (brass) of approved quality, High or low pressure, with plastic floats complete of Jindal /Tata /Zoloto/ UNIK makeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 98 | Providing and fixing 15mm (fifteen millimetre) nominal bore brass Furrulewith C.I.mouth cover including boring and taping the main of Tata/Jindal makeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 99 | Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm (twenty millimetre)to 40 mm ( forty millimetre)nominal bore by providing and fixing tee including cutting and threading the pipes completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 100 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (onecement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design including cutting and threading the pipes complete Inside size 90x80 cm (ninety into eighty centimetre)and 45 cm (forty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram)and weight of frame 15 kg ( fifteen kilogram) With common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 (seven point five)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 101 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (onecement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design including cutting and threading the pipes complete Inside size 120x90 cm (one hundred twenty into ninety centimetre)and 90 cm (ninety centimetre)deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimetre) internal diameter, total weight of cover and frame to be not less than 116 kg (one hundred sixteen kilogram)(weight of cover 58 kg (fifty eight kilogram)and weight of frame 58 kg (fifty eight kilogram) With common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 (seven point five)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 102 | Providing and fixing stone ware gully trap make of Perfect, Hind or ISI marked grade ‘A’ complete with CI grating brick masonry chamber in cement mortar 1:5(One cement : five course sand) and water tight C.I. cover with frame of 300 x 300mm (Three hundred into three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg (Four point five three kilogramme) and frame to be not less than 2.72 kg (Two point seven two kilogram) square mouth trap 100x100mm (One hundred into one hundred millimetre) size P-Type including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Chargeincluding other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 103 | Providing and fixing 15mm (fifteen millimetre) nominal sizeG.I. Pipes complete with G.I. fittings and clamps, including making good the walls etcetra concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall Jindal ( Hisar) / TATA makeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 104 | Providing and fixing 20mm (twenty millimetre) nominal sizeG.I. Pipes complete with G.I. fittings and clamps, including making good the walls etcetra concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall Jindal (Hisar)/ TATA makeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 105 | Providing and fixing C.PBrass toilet paper holder of ESSCO (AEC-ESS-1151N)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 106 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Sintex make Tripple Layersincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 107 | Providing and fixing 15mm (fifteen millimetre)dia CP Brass Single lever telephonic wall mixer of quality and make of Jaquar ( OPL-15119) (as approved by Engineer in charge) with provision of hand showerincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 108 | Providing and fixing Hand Shower (Health Faucet) with 8mm Dia,1.2 Meter Long Flexible Tube & Wall Hook of quality and make ofJaquar (ALD-CHR -573)by as per direction of Engineer in Chargeincluding other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 109 | Providing and fixing Single socketed pipes 90mm (Ninety millimetre)dia of Supreme/Fenolax/ Vectus make on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimetre)gap for thermal expansion complete upto all floor levelincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 110 | Providing and fixingCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 100 mm (one hundred millimetre) inlet and 100 mm (One Hundred millimetre)outlet trap of self cleaning design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floorsincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 111 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Finolax,D-Plast/Vectus make) conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion Single tee with door 90x90x90mm (Ninety into ninety into ninety millimetre) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 112 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Finolax,D-Plast/Vectus make) conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion Single tee with door 110x110x110mm (One hundred ten into one hundred ten into one hundred ten millimetre) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 113 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Finolax,D-Plast/Vectus make) conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion Single tee with outdoor (Ninety into ninety into ninety millimetre) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 114 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Finolax,D-Plast/Vectus make) conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion Single tee with outdoor 110x110x110mm (One hundred ten into one hundred ten into one hundred ten millimetre) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 115 | Providing and fixing 90mm (Ninety millimetre) bend 87.5° (Eighty seven point five degree) on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Fenolax/D-plast/ vectus make) of 6kg/cm2 (Six kilogramme per centimetre square) pressureconforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 116 | Providing and fixing 110 mm (One hundred ten millimetre) bend 87.5° (Eighty seven point five degree) on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes (Supreme/Fenolax/D-plast/ vectus make)of 6kg/cm2 (Six kilogramme per centimetre square) pressureconforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion completeincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 117 | Providing and fixing 90mm (Ninety millimetre)dia of D-plast or vectus make unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 118 | Providing and fixing 110mm ( one hundred ten millimetre)dia of D-plast or vectus make unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 119 | Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm (forty millimetre) nominal size) up to Haunches of S.W. Pipes of 100mm (one hundred millimetre) dia including bed concrete as per standard design including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 120 | Supplying and fixing Cast Iron Cover without frame for manhole 455x610mm(Four hundred fifty five into six hundred ten millimetre) rectangular C.I. cover (Light duty single seal pattern-I) the weight of cover to be not less than 23kgs(Twenty three kilogramme)including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge andincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 121 | Providingfixing M.S. foot restsin manholes with 20x20x10 cm (twenty into twenty into ten centimetre) cement concrete blocks of 1:3:6 (one cement : three coarse sand : six graded stone aggregate 20 mm (twenty millimetre) nominal size) as per standard design with 20x20 mm(twenty into twenty millimetre) square bar including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 122 | Providing and fixing 110mm ( one hundred ten millimetre)dia of Supreme/Fenolax/ Vectus make unplasticised PVC pipe of approved design weephole in brick masonry/ stone masonry/plain reinforced concrete , abutment, retaining wall, wing walls with PVC pipe extending through the full width of the structures with slope Single socketed pipes 1 (v) : 20 (H) (one vertical: twenty horizontal)towards drawingincluding entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 123 | Back filling behind abutment , wing wallsandreturn walls complete as per drawings & MORD technical specification granular materialas per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 124 | Banking excavated earth in layers not exceeding 20 cm (Twenty centimetre) in depth, breaking clods, watering, rolling each layer with ½ (One & half) tonne roller, or wooden or steel rammers, and rolling every 3rd (Third) and top-most layer with power roller of minimum 8 (Eight) tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etcetera in all kinds of soil upto all leads and lifts as per direction of Engineer-in-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malakana, toll tax, sale tax or other taxes imposed by the Government. |
| 125 | Construction of granular sub-base by providing close graded Material conforming to secifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads and lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, With material conforming to Grade-II size range 53mm to 0.075 mm (Fifty three to zero point zero seven five millimetre) having CBR Value-25complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 126 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) ( fifty three millimetre to zero point zero seven five millimetre ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads and lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne ( eight to ten tonne)capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge as per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 127 | Providing and laying in position design mixcement concrete M-25 (M-twenty five) grade with minimium cement contents not less than 400kg ( four hundred kilogram) with graded/crushed stone aggregate 20 mm (Twenty millimetre) nominal size including finishing and making of grooves as expansion joints in cement concrete pavement workexcluding the cost of centering, shuttering,and reinforcement including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge. The rates are inclusive of octroi, royality, malakana, toll tax, sale tax or other taxes imposed by the Government. |
| 128 | Providing and applying primingcoat with bitumen Emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer @ 0.70 to 1.00kg/sqm (Zero point seven zero to onekilogram per square metre) using mechanical means as per Technical Specification and as per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 129 | Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface and cleaning with mechanical broom. With rapid setting bitumen emulsion -On WBM/WMM @ 0.225kg/sqm (Zero point two two five kilogramme per square metre) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 130 | Providing and laying Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, 50 to 100 mm (Fifty to one hundred millimetre) average compacted thickness with bitumen of grade VG-30 (Viscosity Grade-Thirty) @ 3.5% (Three point five percent) (percentage by weight of total mix) and lime filler @ 2% (Two percent) (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 (One hundred to one hundred twenty) TPH capacity complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 131 | Providing and laying Bituminous concrete 25mm (Twenty Five millimetre) compacted thickness with bitumen of grade VG-30 (VISCOSITY GRADE-THIRTY) @ 5.5% (Five point five percent) (percentage by weight of total mix) and lime filler @ 2% (Two percent)(percentage by weight of Aggregate) using crushed stone aggregate of specified grading, premixed with bituminous binder and filler prepared in batch Type Hot Mix Plant of 100-120 (Hundred two One hundred twenty) TPH capacity, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification complete and as per directions of Engineer-in-Charge including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 132 | Painting New work (Two or more coats) runway/taxi track/apron marking with adequate Nos. of coats to give uniform finish with road marking paint of superior make (ASAIN/NEROLAC/ICI-DULUX) as approved by the Engineer-In-Charge including cleaning the surface of oil, dirt, scales, grease and other foreign material etcetera and lining out complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 133 | Providing and applying 2.5 mm (Two point five millimetre) thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 134 | Providing and fixing Glow studs (3 M make) dual directional of size 100x20 mm (One hundred into twenty millimetre) made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg (Thirteen thousand six hundred thirty five kilogramme) tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base. The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Chargeincluding all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 135 | Providing and fixing post delineators ( 3 M/ Green Light make)made of ABS round body fitted with 2 Nos (Two Numbers) 100 mm (One hundred millimetre) dia high reflective reflectors and mounted on MS pipe of 65 mm (Sixty five millimetre) dia duly powder coated anti-rust and anti theft steel to be installed including entire carriage of material with within all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Chargeincluding other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. |
| 136 | Providing and laying of boulder apron laid in wire crates with 4mm (Four millimetre) dia G.I.wire conforming to IS:280 and IS:4826 in 100mmx100mm (One hundred into one hundred millimetre) mesh (woven diagonally) including 10% (Ten percent) extra for laps and joints laid with stone boulders weighing not less than 25kg (Twenty five kilogramme) each as per drawing and technical MORD specificatins clause 1301 as per direction of Engineer-in-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malakana, toll tax, sale tax or other taxes imposed by the Government. |
AI Tender Summary
Tender Timeline
Jul 09, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJul 14, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 14, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender