Development Of Park In Jaitpur Extn Part 2, Jaitpur Extn And Near Development Of Park In Jaitpur Extn Part 2, Jaitpur Extn And Near Shamshan Ghat In Badarpur Constituency ( Ac-53 ) .
Tender Value
1.47 Crore
Estimated cost
Bid Submission
14 Jul 2022
0 days left
EMD
2.94 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
badarpur → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Development Of Park In Jaitpur Extn Part 2, Jaitpur Extn And Near Development Of Park In Jaitpur Extn Part 2, Jaitpur Extn And Near Shamshan Ghat In Badarpur Constituency ( Ac-53 ) .
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil |
| 2 | Excavating holes more than 0.10 cum &upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone III) : 8 graded stone aggregate 40 mm nominal size) |
| 4 | Brick work with common burnt clay F.P.S (non modular )bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand) |
| 5 | R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-incharge (cost of earth works in excavation, concrete works in foundation to be paid separately). |
| 6 | Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth levelof 1:2:4 (1 cement : 2 coarse sand (zoneIII): 4 graded stone aggregate 20mm nominal size) |
| 8 | 12 mm cement plaster of mix(1 cement: 4 coarse sand) |
| 9 | Supply of earth including royality, excavation, loading & unloading and carriage by mechincal transport lead upto 5 K.M. and banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers,and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions and lift upto 1.5 m in all kinds of soil. |
| 10 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge |
| 11 | Filling available excavated earthexcluding rock in trenches,plinth,sides of foundations etc. in layers not exceeding 20 cm in depth,consolidating each deposited layers by ramming and watering ,lead up to 50 m and lift upto 1.5 m. |
| 12 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 13 | Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work |
| 15 | Providing & Fixing of Basura Bin make ARIHANT/KOMPAN/ LANDSCAPE STRUCTURE/GRAND SLAMhaving Dimension: • Product Area : 0.6m Dia. (1.9ft Dia.) • Height :0.9m (3.2ft) • Capacity :50 Ltrs. Technical Specification: •Side pole :Side pole made from 65NB Galvanized pipes conforming to IS 1239 with GI thickness up to 60µ welded to GI plated MS Base Plate. •Spacer :Spacer made from 25NB Galvanized pipe conforming to IS 1239. •Bin :Main Pot is made up of 40 x 5 mm thick angle and G.I. sheet. Top cover is also made in G.I. sheet and it is bent in such a way that it formsshape of cap. All pipes/ G.I. sheets are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. •Pipes: All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness upto 60micron. •Pipe Materials or Class: Light Duty (\"A\" Class) & Medium Duty (\"B\" Class) Series of pipes only. Wall thickness of pipe varies according to class / series of pipe used. •Powder coating: It shall be done with pure polyester raw material. Dry film Thickness maintained within the range of 50-70 microns. It is tested foradhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instrument. •Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt & Nuts / Nylon Lock Nuts are used with PVC Bolt Caps. All open ends of pipe been closed by GI / PVC caps for user safety against entrapment. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelines. |
| 16 | Providing and fixing of CHEST PRESS SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM SEATED CHEST PRESS of size 1500x550x1825mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Handgrip to be made from high quality rubber. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 17 | Providing and fixing of FOREARM TWIRL (Small Two wheels) make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM FOREARM TWIRL/TAI CHI SPINNERS TAI CHI SPINNERS of size 1150x1150x1650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. The circular spinners made from 32mm dia hot dipped galvanized steel rods and welded on to the post using a 6mm dia hot dipped galvanized steel supports. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury. Bearing used shall be made maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. on ground with concrete of minimum strength M-25 and J shaped The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 18 | Providing and fixing of SHOULDER TWIRL SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAMBIG SHOULDER WHEEL of size 857x850x1815mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 19 | Providing and fixing of ABS BOARD (Single)make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM ABS Board of size 1400x1366x650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-100 micron thick. All joints of pipe are4 robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Sit up boards and Base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm, colourful and UV resistant and environmental friendly.All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equipment on to it and cover nuts and bolts with technical specifications. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineerin- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 20 | Providing and Installation of PULL UP STATIONof make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Providing, designing and fixing of pull up station,The total frame is made with main post of 114mm dia And 4 mm thick G.I.Pipe as per IS-1239with help of connecting links. It is a combination of two exercises. Pull up section has handle made up of 25 NB G.I. pipes. PVC handgrips are provided at both ends of handle. Back section has hand rest of rectangular pipes. Small 25 NB G.I. pipes are provided for back rest. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps if required for user safety against entrapment. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 21 | Providing and fixing of OVATE STEPPER make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM Ovate stepper of size 1148x585x1486mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. |
| 22 | Providing and Installation of SURF BOARD Double of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 4 mm thick G.I.Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm thick G.I.Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm colorful and UV resistant and environmental friendlyor FRP Material of same specification,Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE/ FRPcaps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipmentsetc |
| 23 | Providing and Installation of LEG LIFT POST of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1050 x 800 x 1150mm fabricated with main post of 114mm dia and 4 mm thick G.I.Pipe as per IS-1239 and 6 no of spacer pipes made by 25 NB G.I. pipes are arranged parallel at equidistance to form a back rest of product. The paired handle pipe consists of 25NB galvanized pipe fixed at the top and bottom of 80NB support pipe main frame. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment. All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc. |
| 24 | Providing & Installation of SKY WALKER of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM.Providing, designing and fixing double cross walker of size 1600 x 600 x 1600 mm fabricated with main post of 114mm dia and 4 mm thick G.I.Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm G.I.Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be appliedat all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 8mm colorful and UV resistant and environmental friendlyor FRP Material of same specification, Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE/ FRPcaps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate.All complete as per thetechnical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc. |
AI Tender Summary
Tender Timeline
Jul 06, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJul 14, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 14, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender