Addn / Altn Of Badminton Court ( Bldg - T / 118 ) At Admin Site At Af Station Bhowali.
Tender Value
8.73 Lakhs
Estimated cost
Bid Submission
21 Jul 2022
0 days left
EMD
17460
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bhowali → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Addn / Altn Of Badminton Court ( Bldg - T / 118 ) At Admin Site At Af Station Bhowali.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation of earth work in trenchs not exceding1.5 m wide & depth for foundation etc or for shaft,wells, etc and n. exc 10 Sqm on plan and n.exc M in depth & getting out in soft/loose soil. |
| 2 | S&F framed work such as grillls gratings, etc, with ends of bars shouldered and / or riveted, or forged into apikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framedwork or water tanks and similar work conforming to Fe 290 gde E 165 complete all as specified and directed. |
| 3 | Excavation in post holes or similar holes n-exc 05 cum each in soft/loose soil, getting each out returnning filling in and ramming with earth or broken rubble around in layers not exc 25 cm watering etc. |
| 4 | M&L PCC type C-2 1:3:6 (40 mm graded aggregate) cement concrete in foundation,fillingand mass concrete. |
| 5 | Mild steel work in tubular trusses including special shaped washer etc complete in using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240 including painted one shop coat of zinc chromate primer paint. |
| 6 | Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, with attachment conforming to Fe-410-W and gde-E-250 as in gusset plate |
| 7 | M&L MS screw bolt diameter of shank 11 to 15mm (machine made) with hexoganal head at one end screwed the other or screwed both ends each screw end fitted with washers and one hexagonal nut, exe 05cm not exe 10cm |
| 8 | S&F of 0.5mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 9 | Ditto all as per item No.18 here-in-before but plain as in ridge |
| 10 | Preparation of new steel surfacesexc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer. |
| 11 | Preparation of new steel surfacesexc. 10 cm width or girth and applying two coats of black bituminous paint paint over a coat of red-oxide primer. |
| 12 | Preparation of new steel surfaces n. exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer. |
| 13 | M&L forpower coated aluminium (minimum thickness of powder coating 50 micron) workfordoors, windows ,ventilators and partions (Fixed portion) with extruded built up standard tubular section /appropriate Z section and other sections of approved make conformingto IS 733 and IS : 1285,fixingwith dash fasteners of required dia and size, incl necessary filling up the gaps at junction,i.e. at Top,bottom and sides with required EFDM rubber/neoprene gasket etc.Aliminium section shall be smooth ,rust free,straight,mitred and jointed mechanically whereever required including cleat angle.aluminium snap beading for glazing/paneling,CP brass/stainless steel screw allcomplete all as specified and directed. |
| 14 | S&F of 4.80 mmthick sheet glass ,ordinary qualityand size exc 0.50 Sqmand fixed to aluminium door shutter and partition wall by means of glazing clips rubber strips etc. |
| 15 | S&F of 12mm thick Toughedglass as in hinged doors,partitions automatic doors and similar work I ncluding cutting to shapen,drilling holes required |
| 16 | M&Lforof glazed ceramic coloured tiles joint free in vertical surfaces of size 350x250x7mm/ 450x300-350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cement mortar 1:4 complete. |
| 17 | M&L for complete removal of existing treatment and applyingtwo coats of OBD over one coat of 3mm thick wall care putty and a coat of primer complete all as specified and directed. |
| 18 | Surface excavation n.exc 30cm deep and averaging 15cmdeep and getting out in soft/loose soil |
| 19 | M&L for PCCtype D-2,1:4:8 with using 40mm graded stone aggregate in foundation, filling & mass concrete |
| 20 | M&L for brickwork with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:4 |
| 21 | M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 |
| 22 | M&L for prepration of new surfacesof plastered or unplastered surfaces and applying two coats of cement base paint over a coat of alkali cement primeras on walls. |
| 23 | Removing excavated materials n exc 50m & deposting where directed all as specified & directed. |
| 24 | Returning filling of soft/disintegrated rockincluding spreading, levelling watering & well ramming in layers nexc. 25 Cm thick in each layers all as specified. |
| 25 | M& L for 100mm thick cement concrete type C-2,1:3:6 with using 40mm graded stone aggregate finished surfaces of concrete topping even and fair without using extra cement |
AI Tender Summary
Tender Timeline
Jul 01, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 23, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender