construction Of Kiosk And Other Allied Works At Neharu (Dharmkote) Billawar. ( Balance Work Of Kiosk And Other Allied Works)
Tender Value
Ref. Documents
Estimated cost
Bid Submission
30 Jun 2022
0 days left
EMD
65900
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
lakhanpur → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
construction Of Kiosk And Other Allied Works At Neharu (Dharmkote) Billawar. ( Balance Work Of Kiosk And Other Allied Works)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil : |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed in All kinds of soils. |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with : ( Incl; all carriages lead and lifts.) |
| 4 | 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 5 | 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 6 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 infoundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 7 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 8 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 9 | Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete ( Incl; all carriages lead and lifts.) |
| 10 | CAST-IN-SITU Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 12 | : Foundations, footings, bases of columns etc. for mass concrete. |
| 13 | Suspended floors, roofs, landings, balconies and access platforms |
| 14 | Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level |
| 16 | 6MM CEMENT PLASTER 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 17 | 15mm Cement plaster on the rough side of single or half brick wall of mix: 13.2.1 1 : 4 ( 1 cement : 4 fine sand) |
| 18 | CEMENT PLASTER (IN FINE SAND)12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 19 | CEMENT PLASTER WITH A FLOATING COAT OF NEATCEMENT12mm Cement plaster finished with a floating coat of neat cement of mix:13.7.2 1 : 4 ( 1 cement : 4 fine sand) |
| 20 | Providing and fixing power coated aluminium workin frames and shutters including glass/pvc panelling and all accessories complete (as per instruction of engineer incharge. |
| 21 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 22 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 23 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1: and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. 11.52.2 Size of tile 600x600 mm |
| 24 | Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.In colour such as White, Ivory, Grey, Fume Red Brown |
| 25 | Providing and laying pressed clay tiles (as per approved pattern 20mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) and finished neat complete. |
| 26 | Making plinth protection with common burnt clay bricks of class designation 7.5 laid on edge in cement mortar 1:6 (1 cement : 6 coarse sand) with 12 mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) over 75 mm bed of dry brick aggregate 40mm nominal size rammed, consolidated and grouted with fine sand . The top of bricks pointed with cement mortar 1:3 (1cement: 3 fine sand) and curing complete. |
| 27 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.13.88.2 2 mm thick. |
| 28 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 29 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 30 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete . Hot finished welded type tubes |
| 31 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required |
| 32 | Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) |
| 33 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade |
| 34 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. (Medium grade by approved manufacture as per instruction of Engineer -in-charge.) |
| 35 | : 15 mm dia. nominal bore. |
| 36 | Internal work-Exposed on wall 15 mm dia. nominal bore |
| 37 | 20 mm dia. nominal bore |
| 38 | 25 mm Dia nominal Bore |
| 39 | Providing and fixing G.i. fitting |
| 40 | Union 15mm |
| 41 | Union 20mm |
| 42 | Ball valve 15mm |
| 43 | Ball valve 20mm |
| 44 | Providing and fixing PVC Pipe line and fitting supreme/prince or equavalentmake 4.50 ky pressure including incasing in C.C. 1:3:6 complete job. |
| 45 | 100 mm dia. |
| 46 | 75mm dia. |
| 47 | Plain bend 100mm |
| 48 | Plain bend 75 mm |
| 49 | PVC Floor Prop. |
| 50 | Providing and Fixing sanitory fitting (C.P fittings Jaquer or equivalent make as per instructions of engineer in charge. |
| 51 | Long Nose bib cock |
| 52 | C.P angle valve |
| 53 | C.p. Jet with pipe |
| 54 | C.P spreader (unional ) |
| 55 | C.P Tower Ring: |
| 56 | C.P waste coupling: |
| 57 | PVC connection |
| 58 | Pvc waste pipe |
| 59 | CP Soap Dish |
| 60 | CP Grating |
| 61 | Providing and fixing viterous china wash basin with pedistal and CP pillor cock ( cera or equivelent ) complete (white in colour) Make and design as per instructions of engineer in charge. |
| 62 | Providing and fixing viterous china EWC pedistal with cover and cistern complete (Make and design as per instructions of engineer in charge. |
| 63 | Providing and fixing stainless steel (double type) sink complete( as per instructions of Engineer in charge |
| 64 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Raj Nagar plain white marble/Udaipur green marble/zebra black marble (Area of slab over 0.5 sqm) |
| 65 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work. |
| 66 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mmthick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : With Sewer bricks conforming to IS : 4885. Inside size 90x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) |
| 67 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of classdesignation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 68 | Providing and fixing PVC Water storege tank of approved brand & manufacture. |
| 69 | Providing and fixing 1 H. P. motor for water lifting including all fittings complete . Cromptom/Usha/Sharp or equivlent as per instructions of engineer incharge. |
| 70 | Supplying, Stacking , and filling River bed material incl watering ramming complete. |
| 71 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 72 | Providing and fixing steel benches, made up of M.S hollow section pipe, cast iron ornamental arms incl; painting and carriage ( As per instructions of Engineer-in- charge) |
| 73 | Providing and fixing PVC pipe4\"\" Dia for weep holes |
| 74 | Back filling Behind Retaining walls with Stones incl ; carriage and royality |
| 75 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge. |
AI Tender Summary
Tender Timeline
Jun 24, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 30, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 01, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender