Construction Of Sub Tehsil Building At Katar Chhoti.
Tender Value
1.26 Crore
Estimated cost
Bid Submission
27 Jun 2022
0 days left
EMD
2.52 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
ratangarh → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Sub Tehsil Building At Katar Chhoti.
BOQ
| Sl. No. | Item Description |
| 1 | PART A - DISMANTLING & CLEARING WORK |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | PART - BCIVIL WORKS |
| 4 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils |
| 5 | Providing and injection Chloropyrifous Emulsifiableconcentrate 20 % with 1 % concentration for PRE-CONSGTRUCTIONAL Anti termite treatment as per IS 6313 part III and amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which approach is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment And Excluding the cost of Chemical Emulsion.) Heptachlor E.C. 20% with 1% concentration. |
| 6 | Supplying chemical emulsionin sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 7 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M10 grade Nominal Mix1: 4: 8 (1 cement : 4 coarse sand : 8 graded stoneaggregate 40mm nominal size). |
| 8 | Dry stone pitching including preparing the surface etc. complete : Coursed rubble. |
| 9 | Random Rubble stone masonry for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall in : Cement Mortar 1:6 (1-Cement:6-Sand). |
| 10 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and lead up to 1.5mtr |
| 11 | CARRIAGE OF MATERIALS including loading and unloading Earth, Sand ,line morrum,manure or sludge For 1Km |
| 12 | Providing and laying in position specified grade ofcement concrete forall RCC structural elements up to plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 13 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. |
| 14 | Providing and laying in position specified grade ofcement concrete for RCC structural elements up to floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (as required ) excluding the cost of centering, shuttering and reinforcementfor Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix |
| 15 | Providing and laying in position specified grade ofcement concrete for RCC structural elements up to floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, girders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix |
| 16 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for up to floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc. |
| 17 | Columns, pillars, posts and struts etc. |
| 18 | Providing M-25 grade concrete by using min 410 kg of cement per cum instead ofM-20 grade design mix. |
| 19 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level.Thermo-mechanically Treated bars (Conforming of relevant IS code) |
| 20 | Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 75mm thick. |
| 21 | Brick masonry with F.P.S. bricks of class designation 75 infoundation and plinth with bricksCement Mortar 1:6 (1-Cement:6-coarse sand). |
| 22 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 23 | Half brick masonry in foundation & plinth using FPS bricks of designation 75 Cement mortar 1:4 (1-Cement:4-coarse sand). |
| 24 | Providing and fixing in CM 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry : Size 100 x 75mm. |
| 25 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure \"A\": 30 mm thick shutter Commercial Veneer both side |
| 26 | Providing and fixing fully paneled/partly paneled/double leaf shutter frame for doors as per approved design and drawings with approved ordinary C.P./ oxidized steel fittings as per Annexure - \"A\" and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete : 30 mm thickGhana wood grade I |
| 27 | Providing and fixing fully paneled /partly paneledsingle leaf shutters frame for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure ‘A’ and width of styles, bottom and top rails 75mm including intermediate rails 50mm wide, beading of 25mm x 15mm size on both faces : 30 mm thickGhana wood grade I |
| 28 | Providing and fixing wood panelling or panelling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled and glazed shutter 25 mm to 40 mm thick 25 mm to 40 mm thick Wire gauge 24 gauge 14 mesh of IS 1568-1970 marked 85 gauge of dia 0.56 mm |
| 29 | 5 mm float glass |
| 30 | Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitered weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitered and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge Window open able. |
| 31 | Supplying and fixing fixed wire gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150 mm distance. 14 mesh x 24 gauge |
| 32 | Providing and fixing Square bars or other flat welded to window, ventilators etc. |
| 33 | Providing & fixing anodizing aluminium work (Anodizing to be got done from approved Anodizer) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS : 733 and IS : 1285 anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing/panelling, C.P. Brass/ Stainless Steel screws, Al. Tower bolt & Al. handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and peeling to be paid for separately). For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (locks shall be paid for separately). Anodised aluminium (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) |
| 34 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.) with float glass panes of 8 mm thickness |
| 35 | Providing and fixing M.S. sheet 1mm thickdouble leaf door shutter in angle iron frame 35x35x5mm suitably diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. in charge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 36 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitered and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 37 | Providing precast cement concrete jali, nominal mix 1:2:4 (1-Cement:2-Sand:4-stone aggregate 6 mm nominal size) reinforced with 1.6 mm dia Mild steel wire, including centering and shuttering roughening, cleaning, fixing and finishing in cement mortar 1:3 (1-Cement:3-fine sand) etc., complete as per approved design excluding plastering of jambs, sills and soffits up to floor three level. 50mm thick |
| 38 | Supplying and fixing wood work in frames of wall panelling, false ceiling partition wall etc. as per approved design and drawing including antitermite treatment. Ghana Teak wood Grade-I Add extra in frames for circular members such as in fan lights, staircase railing etc. |
| 39 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. Extrafor providing D type pipe head as top of hand railing |
| 40 | Supply & fixing of stainless steel pipe railing for ramp / Staircaserailing height, 90 cm. with 50 mm dia stainless steel pipe with 18 gauge with drop (vertical post) at 90 cm. C/C and intermediate3 Nos 20 mm dia horizontal pipe with suitable height of same gauge with coupling, grinding and polishing & fix of master pieces as per required point as per approved design of Engineer in charge |
| 41 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4(1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 60x60 cm |
| 42 | Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm |
| 43 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete For area of each slab from 2001to 5000 Sqcm |
| 44 | Providingandfixing75 mm wide Architectural DecorativeBorderindifferentshadesandin allcoloursinMarble/ Granite flooring laid over 20 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. |
| 45 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. Category - I : Kajariya, Jhonson, Orient, Somani make etc. |
| 46 | Providing and laying Ceramic MAT floor tiles(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown of any size, laid on 20 mm thickbed of cement mortar 1:4 (1 cement : 4 coarse sand)including pointing in white cementmixed with pigment of matching shade complete. |
| 47 | Providing and fixing Granite stone slab mirror polished and machine edge cut in Walls, Pillars, Steps, Shelves, Sills, Counters. Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing of: Green / Black(Madras)/other Above 3601 Cm2 Slabs |
| 48 | Supply & fixing steel shutter (Almirah type) with 18 gauge steel border & steel shutter including locking arrangement and painting etc. complete fixed on wall with joint fast (iron clip) |
| 49 | Grading roof for water proofing treatment withwater proofing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 50 | Crazy marble stone flooring 20mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mixin proportion of 4 : 7 (4cement: 7 white black or white or black marble chips) size from 1mm to 4mm by volume and under layer of 25mm thick cement concrete [1:2:4, graded stone aggregate 12.5mm nominal size] rubbing and polishing and cement slurry etc. complete : In ordinary cement. |
| 51 | Providing batta (gola) 75mm x 75mm in cement concrete (1:2:4) including finished with cement mortar 1:3 as per standard design. |
| 52 | Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. |
| 53 | Providing and fixing up to floor five level pre cast cement concrete string or lacing courses, copings, bed plates, anchor blocks, windows sills, shelves, louvers steps, staircases, etc. including carriage, hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surface, including all T & P, curing etc. complete: M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). |
| 54 | Making grooves as per design in plaster 10mm to 20mm wide. |
| 55 | Washed stone grit plaster on exteriorwalls of height up to 10 M. above level in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2kg of cement per sqm, top layer 15 mm cement plaster 1:1/2:2 ( 1 cement : 1/2 coarse sand : 2 stone chipping size 10 mm nominal size) in panel with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chipping, complete as per specification and direction of Engineer in charge. (Payment for providing grooves shall be made separately) Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster. |
| 56 | Forming groove of uniform size 15x15mm and up to 25x15mm in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of Engineer in charge |
| 57 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20 mm thick. |
| 58 | Rough cast plaster with a mixture of sand and gravel or crushed stone 2.36 mm to 12.5 mm nominal size dashed over and including the fresh plaster in two layer, under layers of 12 mm thick cement plaster and top layer 10 mm thick of CM 1:4 (1-Cement:4-sand) mixed with 10 % finally grounded hydrated lime by volume of cement Under layer of 12 mm thick cement plaster done in cement sand mortar 1:4 (1-Cement:4-sand) : Ordinary cement finish using ordinary cement |
| 59 | 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) |
| 60 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 61 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 62 | Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty,etc complete in all respect. New work. |
| 63 | Applying priming coat:With ready mix pink or grey primer of approved brand and manufacture on wood work hard and soft wood. |
| 64 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :Two or more coats on new work. |
| 65 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). |
| 66 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height up to 10 m), fixing in position and applying a priming coat of approved steel primer all complete. |
| 67 | Stone slab roofing on 2nd floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4,with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge |
| 68 | Supplying and fixing in walls machine cut and polished stone shelves, tands andin CM 1:3 with machine cut edges : Kota stone 25 to 30 mm thick. |
| 69 | P&F double action hydraulic floor spring of approved brand and manufacture to aluminium door shutter confirming to IS : 6315 incl. cost of cutting floors as reqd. embedding in floor and cover plate etc. complete as per direction of Engineer in charge. |
| 70 | Providing & laying Chequered terrazzo tiles of approved make 22mm thick with marble chips of size up to 6mm, in floors, jointed with neat cement slurry mixed wit pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28mm thick bed of C.M. 1:4 : Dark shade using ordinary cement. |
| 71 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxideExtra if square, rectangular hollow tubularsections are used |
| 72 | Providing and fixing stone slabs table rubbed, 15-18 mm thick in Walls, Steps, Pillars, Counters, Jambs, Shelves, Sills etc. laid on 12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. White Marble Makrana \"Adanga\". Above 3601 Cm2 Slabs |
| 73 | Supply and fixing Jodhpur sand stone Machine cut Dash, Coping,sill,lintel fixed in cement sand mortar 1:4 5 cm (2\") thick |
| 74 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 75 | Granite Work |
| 76 | PART - CSANITARY & WATER SUPPLY WORKS |
| 77 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor:Size 580x440 mm. |
| 78 | P & F Europeantype white glazed vitreous china 1st quality W.C. (IS : 2556 Mark) including cutting and making good the wall and floorWall Mounting (syphonic) |
| 79 | P & F water closet Seat Covers with brass hinges complete : Solid PVC (ISI marked) grade-I White for EWC. |
| 80 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: WVC with C.P. brass bend. |
| 81 | P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted,1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) &32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall.: Size 580 mm x 450 mm |
| 82 | P & F 1st quality WVC pedestal for wash basin. |
| 83 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make (Atul, Modi Guard, Saint Gobin or equivalent) complete with 6mm thick commercial ply base fixed to wooden screws & washers.Other sizes |
| 84 | P & F Acrylic Toilet accessories set consisting of Towel rail, shelf, towel ring, soap dish, paste & brush holder & twin peg of approved quality/make. |
| 85 | P&F Grating of approved quality/ make Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make |
| 86 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 87 | Providing and fixing C.P. flange for 15mm dia taps |
| 88 | Making connection of G.I. distribution branch with G.I. main including all fitting. Up to 25mm dia |
| 89 | P & F Extension Pipe for bib cocks of approved quality/make. C.P. brass of Heavy & Superior quality 50x15mm |
| 90 | Providing and fixingSuperior quality (Jaquar ContinentalOr equivalent) CP Brassfittings complete as per direction of EI Long body Bib Cock 15 mm nominal size |
| 91 | Single lever wash basin mixer with 450 mm long copperconnection pipe |
| 92 | Hand shower with 8 mm dia 1 mt long PVC tube & wall hook complete |
| 93 | P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete : Brass wt. 1000 gm, 25 mm. |
| 94 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Geyser etc.C.P.brass Inlet connection with 37 Cm. long pipe and nut. |
| 95 | P & F Full-way valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 15 mm nominal bore. |
| 96 | Gun-metal 25 mm nominal bore. |
| 97 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 litres capacity. |
| 98 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) 20mm nominal outer dia pipes |
| 99 | 32mm nominal outer dia pipes |
| 100 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work). 40 mm nominal outer dia pipes |
| 101 | Providing Laying & jointing glazed S.W. pipes grade `A` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1:1, excavation & refilling of earth in all types of soil up to 1.2m depth, S.W. fittings, including testing of joints etc, complete. 200mm dia |
| 102 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)(Excluding cost of pipe)200mm dia S.W. Pipe. |
| 103 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 75mm dia |
| 104 | 110mm dia |
| 105 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Reducer 110 x 75 mm dia |
| 106 | 110 mm dia |
| 107 | Plain Tee 75 mm dia |
| 108 | 110 mm dia |
| 109 | Bend 45 110 mm dia |
| 110 | Bend 87.5 75 mm dia |
| 111 | 110 mm dia |
| 112 | Vent cowl 110 mm dia |
| 113 | Socket plug 110 mm dia |
| 114 | Pipe clip 110 mm dia |
| 115 | Gully Trap 110mm dia |
| 116 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size size 450 x 450mm depth up to0.5 M Cement cover with frame |
| 117 | Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering,jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth worketc . complete including disposal of surplus earth within a lead of 50 mtr .Inner dia90 Cm & 10 to 12 Mtr deep. |
| 118 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja,50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design ,two No. 450 mm dia each Ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 200x100x130 cm.(for 10 users) |
| 119 | Size 400 x140x150 cm.(for 50 users) |
| 120 | Construction of Open SurfaceDrain with 112mm thick brick masonry in CM 1:4,110mm thick base concrete 1:5:10, 37mm thick M-15 grade C.C. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing: 250mm drain 300mm av. Depth |
| 121 | PART - DBOUNDARY WALL & TANK WORKS |
| 122 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils |
| 123 | Add extrafor every additional lift of 1.5 Mtr. or part thereof : In all kind of soils. |
| 124 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and lead up to 1.5mtr |
| 125 | Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. |
| 126 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transportingtosite,spreading,gradingtorequiredslopeandcompactingtomeetrequirementof Tables 300-1 and 300-2 with a lead upto 1000 m as per MoRTH Specification Clause 305.3 |
| 127 | Haulage of materials by tipper excluding cost of loading, unloading and stacking. Surfaced RoadFor 5 Km |
| 128 | Dry stone pitching including preparing the surface etc. complete : Coursed rubble. |
| 129 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M10 grade Nominal Mix1: 4: 8 (1 cement : 4 coarse sand : 8 graded stoneaggregate 40mm nominal size). |
| 130 | Random Rubble stone masonry for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall in : Cement Mortar 1:6 (1-Cement:6-Sand). |
| 131 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 132 | Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 75mm thick. |
| 133 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 134 | Rough cast plaster with a mixture of sand and gravel or crushed stone 2.36 mm to 12.5 mm nominal size dashed over and including the fresh plaster in two layer, under layers of 12 mm thick cement plaster and top layer 10 mm thick of CM 1:4 (1-Cement:4-sand) mixed with 10 % finally grounded hydrated lime by volume of cement Under layer of 12 mm thick cement plaster done in cement sand mortar 1:4 (1-Cement:4-sand) : Ordinary cement finish using ordinary cement |
| 135 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. |
| 136 | Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 20mm thick. |
| 137 | Finishing with neat cement (punning). |
| 138 | Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty,etc complete in all respect. New work. |
| 139 | Supply and fixing Jodhpur sand stone Machine cut Dash, Coping,sill,lintel fixed in cement sand mortar 1:4 15 cm (6\") thick |
| 140 | Stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4,with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge |
| 141 | Grading roof for water proofing treatment withwater proofing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 142 | Providing & laying Chequered terrazzo tiles of approved make 22mm thick with marble chips of size up to 6mm, in floors, jointed with neat cement slurry mixed wit pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28mm thick bed of C.M. 1:4 : Dark shade using ordinary cement. |
| 143 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxideExtra if square, rectangular hollow tubularsections are used |
| 144 | Providing and fixing cow catcher made of R.S. joist angles channels MS rounds including cutting welding and fabrication with priming coat of red oxide (as per design). |
| 145 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :Two or more coats on new work |
| 146 | Providing and fixing up to floor five level pre cast cement concrete string or lacing courses, copings, bed plates, anchor blocks, windows sills, shelves, louvers steps, staircases, etc. including carriage, hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surface, including all T & P, curing etc. complete: M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). |
| 147 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). |
| 148 | PART - EPAVEMENT WORKS |
| 149 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size). |
| 150 | Providing and layingfactory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction and of approved size and design/ shape laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. General specification of blocks:1) Shape as defined by Engineer incharge 2) Tensile splitting strength and braking load as per BS 6717:2001 3) Color: Grey cement natural colour 4) Variation in dimension: Less than 1.6mm.5) Variation in thickness: Less than 3.2mm 6) Abrasion: As per BS: 6717:2001 80 mm thick |
AI Tender Summary
Tender Timeline
Jun 23, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 27, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 28, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender