|
| 1 | Excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches.PWD-251 |
| 2 | Boring with hydraulic piling rigs with power units, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles dsr-20.3.1 |
| 3 | Filling of carted earth in plinth including supply of necessary quantity of sand from a distance not exceeding 8km from the side of work and including watering dressing etc. required for proper completion of work.(lead up to 30m & lift 1.5m)Analysis |
| 4 | Providing & laying cement concrete in 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggreagate 40mm nominal size) including supply of all materials,labour and T & P etc. required for completion of work and curing complete including cost of form work in foundation and floorsPWD-281 |
| 5 | Sand Filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8km from the side of work and including watering dressing etc. required for proper completion of work.(lead up to 30m & lift 1.5m)PWD 255 |
| 6 | Providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete. (plinth area of the building at ground floor only shall be measured as per I.S.6313 (PartII 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows : (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4) Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 7.5 liters/sqm (6) Treatment of soil under apron along external perimter 5 liters/sqm. (As per manufacturer\"s standard dilution) |
| 7 | Re-inforcement cement concrete workwith cement approved coarse sandand2cm. (3/4\") guageapproved stoneballastin the proportion 1:1.5:3,(1cement :1.5corse sand 3 grit) in R.C.C.Raft foundation and footing excludingsupply of reinforcement and its fixing and bending but including its fixing and bindingthe same necessarywith 24 BWG bindingwireand including necessary centeringand shuttering etc.and also including supply of all materials,labour andtools and plants etc, required forproper completion of the worksAs in item PWD-283but inR.C.C.Raft foundation and footingwithapproved stone ballast.(Using1:1.5:3Mix concrete) PWD-287+289-288 |
| 8 | R.C.C. (M-20) work with cement approved coarse sand and 20 mm. guage approved stone ballast in the proportion of 1:1.5:3 (M-20) in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire cost being inluded in the item.PWD 283(I) |
| 9 | R.C.C. (M-20) work with cement approved coarse sand and 20 mm. guage approved stone ballast in the proportion of 1:1.5:3 (M-20) in slab excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire cost being inluded in the item. |
| 10 | R.C.C. (M-20) work with cement approved coarse sand and 20 mm. guage approved stone ballast in the proportion of 1:1.5:3 (M-20) in beams excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire cost being inluded in the item.PWD 285(I) |
| 11 | Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work(whennot includedin anover all rates )wroughttorequired shape as necessary including bending for proper completion of thework andincluding supply of steel itswastage and over lapping and hookes required for completion of the work TMT Fe 500PWD 504 |
| 12 | M-150 brick work in 1:6 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work.PWD 307-306+303 |
| 13 | M-150 brick work in 1:6 (one cement and six coarse sand sand of 2.25 fineness modulus) mortarin super-structure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. (1:6 cement : coarse sand)PWD 307-306+303+309+310 |
| 14 | M-150 brick work in 1:4 (one cement and four coarse sand sand of 2.25 fineness modulus) mortarin super-structure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. (1:4 cement : coarse sand)PWD307-306+305+309+310a |
| 15 | Supply and fixing of anodised /aluminium windows having 2 mm thick aluminium section excluding coating & an average coating of 20 micron fully glazed made of aluminium door tube size 83.5x 44.65 mm as vertical member & 1114.00 x 44.45 mm size tube in bottom and horizontal members door chaukhat should be of aluminium tublar vertical with two openable shutters. The rate will include cost of material fixtures, 5mm glass handles, locks, screw necessary beeding & excluding cost of floor spring if required for proper completion of work as per direction of Engineer I/C.(FOR DOORS, WINODW & VENTILATORS)with 5.0mm thick plain glassAMETHI S.O.R. CH--19 |
| 16 | Mild steel & iron work of small size & section such as holding down bolts hold fast tie rods garting etc (when not included in & over all rates) brought to required form including supply of steel & its wastage including cost of bolts nuts if required for proper completion of the work includind fabrication of holes in door chowkhats and nosing (Angle iron door frame)PWD 502 |
| 17 | Supply & fixing of flush door commercial quality conforming of IS 2202 part 1 (1983) including fixing of wooden cleats & stoppers and including fixing & adjustment of hinges ,bolts,locls,handles springs,fitting with necessary screws to be supplied departmentallyPWD 470(2 |
| 18 | Mild steel Iron Grill & staircase railing of a approved quality and drawing including supply of all materials, fabrication labour T & P in all respect as per direction of Engineer in charge for proper completion of the work.CH-10 NEW-3 |
| 19 | Supply of Approved M,S, Z-section windows and ventil excluding cost of glass panes but including supply of all material its fabrication nuts and bolts, hold fast for proper completion of work asdirection of engineer-in-charge and also including cost of handle stays rod etc. and one coat of red oxide paint complete in the aall respect site of work. CH-10 NEW ITEM 1( Z section )CH-10 NEW-1 |
| 20 | Supply and fixing of integrated foam PVC (solid pvc) 65x42 mm Door frame and 25 mm thick door shuttermade of solid foam pvc sheet with both side laminate finish without lead and cadmium stablized manufactured by ISO-9001, ISO-14001 AND ISO- 18001 quality and environmental managegement accredited company having 525 kg/cum density .The work include cost of anodized aluminium sliding bolt ,handles shoot bolt and hinges .all edge to be white polished with titanium die oxide and melamine . The frame to be fixed to wall using dash fastner and gap to be filled with white colour silicon sealant .Allthe work to be completed as per direction of engineer in chargepanels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 21 | Fixing Chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonary for holdfast embedding hold fast in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size) painting two coats of approvedwood preservative to sides of chowkhats and making good the damage to walls and floors as required complete including disposal of rubbish to the dumpingall complete as per direction of Engineer in charge. VARANASI Ch-10 S.No.9 (a) Door chaukhats |
| 22 | Fixing Chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonary for holdfast embedding hold fast in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size) painting two coats of approvedwood preservative to sides of chowkhats and making good the damage to walls and floors as required complete including disposal of rubbish to the dumpingall complete as per direction of Engineer in charge. VARANASI Ch-10 S.No.9 (b) Window chaukhats |
| 23 | Fixing Chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonary for holdfast embedding hold fast in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size) painting two coats of approvedwood preservative to sides of chowkhats and making good the damage to walls and floors as required complete including disposal of rubbish to the dumpingall complete as per direction of Engineer in charge. VARANASI Ch-10 S.No.9 (c) Ventilator chaukhats |
| 24 | 15mm thick plaster wit cement mortar in proportion of 1:4 cement & Coarse sand) in plinthPWD 17.59(II) |
| 25 | 15mm cement plaster on rough side of single or half brick wall with cement mortar of mix1:6 cement & Coarse sand PWD17.59(III) |
| 26 | 12mm thick plaster with cement mortar in proportion of 1:6 cement & Coarse sandPWD 17.58 |
| 27 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) SOR LKO13.47.1 |
| 28 | Making drip course in sun shade or facia as per direction of Engineer incharge DSR 5.30 |
| 29 | Supply and fixing 6 mm (1/4\")thick china white glazedtiles inflooringorin skirting or dado laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry jointing and polishing complete includingsupplyof allmaterials, labour and tool sand plantsetc.required forproper completion of the work.(Dado/skirting)PWD-628 |
| 30 | Cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand: 4 graded stone of size 12.5mm nominal size)laid in one layer finished with floating coat of neat cement (25mm thick floor)PWD 14.69 |
| 31 | Applying priming coat over new steel and other metal surface upto 10cm in width or girth or small not exceeding 0.10 Sq.M area after and including preparing the surface by throughly claring oil grease,dirt and other foreign matter and scoured with wire brushed fine steel/wood. Scrapper sand papering and knotting including cost of all materials labour T & P etc required for proper completion of work.PWD-641+642 |
| 32 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) SOR LKO13.47.1 |
| 33 | Finishing walls with putty (1 mm thick) approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material labour T & P etc required for proper completion of work.LKO PWD 13.80 |
| 34 | Wall painting (two coats) with plastic emulsion paint of approved brand & manufacture on decorative wall surface to give an even shade including throughly brushing the surface clean all of dirt,grease loose pieces & prepare smooth surface including cost of all mterials labours T & P etc complete required for proper compleion of the work.AGRA CH-15 S.NO. 27+28 |
| 35 | Distempering with oil bound distemper of approved brand & manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J & N ,Shalimar Asian paints after throughly brushing the surface free from mortar droppings and other foreign matter & also including preparing the surface even with plaster of approved synthetic material & sand paperd smooth including cost of all materials labour T & P etc complete required for proper completion of the work.PWD 649+650 |
| 36 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panesPWD 812© |
| 37 | Providing & fixing stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 300mm x 16mmlko material rate |
| 38 | P/Fixing stainless steel tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as / IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. 250 mm x 10mmlko material rate |
| 39 | Providing & fixing stainless steel towerhandleswith screwsand 150mm long.SI marked LKO material rateLKO material rate |
| 40 | Providing & fixing oxidised sliding door bolts ISI markeddyed to required colour or shade with nuts and screws etc complete. (a) 300mm x 10mm material rate |
| 41 | P/Fixing oxidisedtower bolts ISI marked dyed to required colour or shade with necessary screws etc. 250 mm x 10mm material rate |
| 42 | Providing & fixing Oxidisedhandleswith screwsand 150mm long.SI marked LKO material rate |
| 43 | Kota stone slab flooring over 20 mm thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar ( 1 cement : 4 c sand)PWD 14.43 B |
| 44 | Providing and fixing strips of 3 mm thickness in joints of floor and skirting at the time of laying floors flush with floor level including labour,tools,plants etc. completeMaterial rate |
| 45 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent DSR 11.56.2 |
| 46 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete 600x600xmm size tilesCH-14 NEW-2 |
| 47 | P&L Brick coba 120 mm thick laid with M-150 class brick bats coba7.50cm thick gap of 15mm to each other,over 20mm thick base of cement mortar 1:4 cement & coarse sand mixed with water proofing compund spreading cement slurry mixed with aerelic cement concrete water proofing compund filled gaps of coba & top of coba mortar mixed with water proofing compoundin 1:4 cement & coarse sand mortar finished smooth & top mashed false square 30cm x30cm and side wall parapet shall be mono tythic plaster wall upto 30cm.higher and junction and corner shall be rounded by brick ballast cement & coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compund @ 2% by weight & including S/O all material labour T&P etc complete for proper completion of work.CH-11 NEW |
| 48 | Providing & laying cement concrete in 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggreagate 20mm nominal size) including supply of all materials,labour and T & P etc. required for completion of work and curing complete including cost of form work in foundation and floorsPWD 279 |
| 49 | Providing & fixing Toughened glass with putty and glazing clips in windows, clerestory windows, all complete with :5.0 mm thick glass panesMR |
| 50 | Painting on DPC with two coats of air blown VG-10 grade @ 1.70kg/sqm approximate including cost of fuel if anyCH-7 NEW |
| 51 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 17.1.1 |
| 52 | Providing and fixing white vitreous china pedestal type water closet( European type W.C. pan ) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid. 17.2.1 |
| 53 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 630x 450 mm with a single 15 mm C.P. brass pillar tap. 17.7.3 |
| 54 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.31 |
| 55 | Supplying & Fixing ofCP soap tray fixed to the wallwith PVC rubber plug with CP brass screwsMake-Hindware, Model-F840004 (m.r) |
| 56 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. a) 110mm diameter 12.41.2 |
| 57 | Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work. S.no.34,36,37,38,39,40 & 4190 mm O.D. |
| 58 | Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work. S.no.34,36,37,38,39,40 & 41 110 mm O.D. |
| 59 | Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali. S.no.35 |
| 60 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall 25mm dia nominal outer dia pipes 18.7.3 |
| 61 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall 32 mm dia nominal bore |
| 62 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 15mm dia nominal outer dia pipes |
| 63 | (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.20mm dia nominal outer dia pipes18.8.2 |
| 64 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 25mm dia nominal outer dia pipes 18.8.3 |
| 65 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 15mm nominal bore 18.49.1 |
| 66 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore 18.53.1 |
| 67 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality(screwed end). 18.17.1 25mm dia nominal bore |
| 68 | Supply and hoisting of Sintex or equivalent high densitypolyethylene seemless of piece moulded tanks and placing the same in proper position including all taxes, labour and T&P etc. for proper completion of work. Tnak should be ISI marked, Sintex or equivalent. For 3000 litresx2 nos. 18.17.1A |
| 69 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. SI No-14.43.2. a) 110mm |
| 70 | Providing and fixing square-mouth S.W. Gully trap class SP-I complete with C.I. grating brick masonary chamber with water tight C.I. cover with frame of 300x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: with common burnt clay F.P.S.(non modular) bricks of class desiganation M-150. 19.4.2.1 a) 150x100 mm. size P type |
| 71 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design19.7 Inside size 900x800mm and 450mm deep including CI cover with frame With FPS bricks of class designation 150 19.7.1.1 |
| 72 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. in trenching 32mm nominal bore.18.9.4 |
| 73 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. 12.22 |
| 74 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm |
| 75 | Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in PVC conduit with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with modular typeswitch & ceiling rose / angle / batten holder on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash 138( C) +187(A) |
| 76 | Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitwith modular typeswitch, G.P. Box & ceiling rose on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash. 140( C) +187(A) |
| 77 | Wiring point for plug 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitwith modular typeswitch & socket etc, complete in all respect including matching colour wash. 141( C) +187(C) |
| 78 | Supply & wiring of submains with two number2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. 1307(C) |
| 79 | Supply & wiring of submains with two number4 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. 221(C) |
| 80 | Supply and Fixing of LED Tube Light with batten suitable for up to 1X22 watt LED tube light fitting complete including tube on surface complete in all respect. CAT-AAA1413 |
| 81 | Supply of Ceiling Fan with motor of A.C. Permanent insulation capacitor rating confirming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated volage 220/240 volts, 50 Hz, 1-ph A.C.the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. 1501 BEE 5 Star rated-1200mm sweep |
| 82 | Supplying & Laying of 25mmx3mm G.I. Strip from earth electrode in ground as required complete in all respects. 701 |
| 83 | Supplying & Laying of 25mmx3mm G.I. Strip from earth electrode in ground as required complete in all respects. 716 |
| 84 | Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects.723 |
| 85 | Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve 6 - 32 amps.Cat. A-1002 |
| 86 | Supply and fixing of surface/ flush mounting 6 way TPN distribution board with additional metal doorwithout MCB complete in all respect, as directed at site by Engineer Incharge. CAT-A 1027A |
| 87 | Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6sqmm cables, including tapping with insulating tape,etc. complete in allrespects. 1129 |
| 88 | Supply and fixing of single pole MCB blanking plate CAT-A 1034B |
| 89 | Supply and fixing of power plug with 20A/250 V flush type modular switch and 5 Pin 20 A/250 Volt flush type universal modular socket switch on concealedM.S. box including supply of all material, labour T & P etc required for proper completion of work. 1139A |
| 90 | Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects. 1116 |
| 91 | Erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. 1120 |
| 92 | Supply & fixing hexagonal/Round G.P. Fan box of approved make made up of 1.0 mm thick ISI marked G.P. Sheet spot welded four to Eight holes of 25.4mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5mm G.P. Sheet made upper & lower cover duly screwed fitted with 300mm round zink coated M.S. Bar x 12mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material labour, T & P etc required for proper completion of the work. 1149 |
| 93 | Supplyfixingofelectronic fan regulator (Modular) 120-280 V. ISImarked, on the existing switch board including making connetion, required material, labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work. 1203C |
| 94 | Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc 10sqmm 4 core 501(h) |
| 95 | Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materia ls and labour for proper completion of work. PWD 1131 A |
| 96 | Supply & fixing of CO2 type fire extinguisher,6.5 kg. capacity(ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.PWD-1132(A) |
| 97 | Providing & fixing of Manual Fire Alarm System providing and installing as per directed Enginer in charge approved make and quility including all material labour and T&P required for proper completion of work. |
