Provision Of Guard Rest Room Near Capt Md Accn, Spl Repair To Bldg No T-54 And Cerrain Minor Work At Leimakhong Mil Stn
Tender Value
32.20 Lakhs
Estimated cost
Bid Submission
28 Jun 2022
0 days left
EMD
64400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
leimakhong → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Provision Of Guard Rest Room Near Capt Md Accn, Spl Repair To Bldg No T-54 And Cerrain Minor Work At Leimakhong Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | B/R work |
| 2 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles and removing unserviceable materials from site of work complete all as specified and directed. |
| 3 | M&L for brick work with subclass ‘B’ bricks, (locally available best quality) old size bricks straight or curved on plan exc 6 m means radius, built in cement mortar (1:6) complete all as specified and directed. |
| 4 | Ditto all as per item no 2 above but except bricks. complete all as specified and directed. |
| 5 | M & L for rendering 15mm thick plaster incement mortar (1:6) on fair faces brick work or concrete surfacesfinish the surfaces even and smooth without using extra cement complete all as specified and as directed. (using Dimapur Sand) |
| 6 | M&L for rendering 15mm thick on fair faces of brick work in cement mortar (1:4) using water proofing compound @2% by weight of cement as per manufacture instruction and finishing the surface even and smooth without using extra cement complete all as specified & directed.(Using Dimapur Sand)[Note: WPC will be measured and paid separately) |
| 7 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick thickness below or above ground level complete all as specified and directed. |
| 8 | Demolition of cement concrete (reinforced) in ground floor and pavings not exc 15 cm thick thickness below or above ground level complete all as specified and directed. |
| 9 | M & L for PCC M-10 grade, (Nominal mix) (using 40mm graded stone aggregate), as in foundation, filling and mass concrete complete all as specified and as directed. |
| 10 | M&L for 75mm thick PCC M-10 grade(Nominal mix) using 40mm graded stone aggregate as in plinth protection finishing surfaces even andsmooth without using extra cement complete all as specified and directed. |
| 11 | M & L for RCC M-15 nominal mix using 20mm graded crushed stone aggregate in foundations, including rafts, footings, foundationbeams; plinth beams; basesfor columns, etc.; basement slabs, under-reamed pilesand mass concrete vcomplete all as specified and directed. |
| 12 | Use and waste of formwork to sides and soffits of floor or plinth beams, beam haunchings, etc. vertical or to batter, roughfinished surface of concrete complete all as specified and directed. |
| 13 | M & L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. |
| 14 | Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 15 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all asdirected. |
| 16 | M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge. |
| 17 | M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skirtingetc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including rendering 10 mm thick on fair faces of brick work in CM (1:3) for receving vertical dado tiling complete all as specified and directed. |
| 18 | M & L for non skid coloured ceramic tiles 7 to 8mm thick jointless (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr in Charge |
| 19 | M & L for Glazed Coloured Ceramic tiles in vertical surface 350x250x7mm / 450x350x7mm thick jointless set and joint in neat cement slury and pointed in white or colour cement to match over and including 10mm thick plaster in CM 1:4 as backing coat to receive tiles complete all as specified and directed. |
| 20 | Dismantling plain or corrugated stell sheeting, any guage, thickness, including Nainital or similar pattern roof covering complete all as specified and directed |
| 21 | S&F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 22 | S&F Pre-Painted galvantume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 23 | Dismantling wall and ceiling boards (fibre, plup, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets complete all as specified and directed.NOTE : Dismantling of false ceiling to be carried out carefully without damaging of existing fitting andfixtures offalse ceiling itmes |
| 24 | Providing & Fixingfalse ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross \"T\" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main \"T\" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI soffit cleats fixed to existing truss with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge. |
| 25 | S&F Vitreous China Wash down water closet (Pedestal pattern) white excluding fixing balts flushing cistern and flushing pipe, fixed in repairs complete all as specified and directed. |
| 26 | S&F, in repair light coloured vitreous china WHB white oval shape of500mmx400mm (minimun)on new brackets excluding taps, waste china & plug including bracket etc complete all as specified and directed. |
| 27 | S&F for fancy typepillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks & fly nuts for iron pipe of 15mm bore fancy type complete all as specified and directed. |
| 28 | S&F in repair 10 ltrs capacity high or low level flushing cistern PVC of selected white valveless syphonoic action type inlet ball valve float and handle 10 ltrs discharge capacity complete including PVC connection and brackets all as specified. |
| 29 | S & F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 30 | S&F brass chromium plated shower rose with or without switch joints 125mm size including fixed to steel pipes or union as fixed in repairs complete all as specified and directed. |
| 31 | S&F, in repairof CP brass fancy typestop cock with long shank,concealed type complete all as specified and directed. |
| 32 | S&F in repairstop valves(ISI marked) cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) for 15mm bore pipe complete all as specified and directed. |
| 33 | S&F towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. (Minimum weight 190gms) |
| 34 | S&F brass chromium plated, 600mm long between flanges tubular towel rail , 20mm dia, D type. fixed with and including chromium plated brass screws and wooden plastic cleats,complete all as specified and directed. |
| 35 | S & F in repairs15mm bore bib taps, cast copper alloy, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed. |
| 36 | S &FPVC connection15 mmboreand45 to 60 cmlongcomplete all as specified and directed. |
| 37 | S & F grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed. |
| 38 | S&F600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 39 | S & F in repairs fancy typedecorative Draparyrod of 20mm dia for window and doors with curtain rings and decorative doom holders fixed to wall with screw complete all as specified and directed. |
| 40 | S&F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed. |
| 41 | S&F for 110mm Bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 42 | S&F for 75mm Bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 43 | S&F 110mm borePVC (SWR) bends complete all as specified and directed. |
| 44 | S&F 75mm borePVC (SWR) bends complete all as specified and directed. |
| 45 | M&L forPVC (SWR) vent cowl of bore 110mm complete all as specified and directed.(Make : KISHAN/ SUPREME /PRINCE /ANANT /ORIPLAST) |
| 46 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 47 | S&F 75mm dia PVC (SWR) floor trap, plain with grating including setting and jointing with solvent cement completeall as specified and directed. |
| 48 | M&L for preparation of new decoratedsurfaces of wall applying two coat of cement base paintand one coat primer complete all speciified and directed |
| 49 | M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed. |
| 50 | Taking up or down 15mm dia of steel tubing and connections and removal from site complete all as specified and directed. |
| 51 | Taking up or down 20mm dia of steel tubing and connections and removal from site complete all as specified and directed. |
| 52 | Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good ,cutting n, exc. 10cm girth complete all as specified and directed. |
| 53 | S&F for 15 mm dia medium grade galvanised,with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 54 | S&F for 20 mm dia medium grade galvanised,with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 55 | Disconnecting existing tanks of capacity exc. 250 & n exc. 500 ltrs , setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position.complete all as specified and directed. |
| 56 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but not exc. 4 sqm each and removing all unserviceable materials from site complete all as specified and directed. |
| 57 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each and removing all unserviceable materials from site complete all as specified and directed. |
| 58 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 59 | M&L for 30mm thick well seasoned 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass etc. (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred bead for securing gauge etc size of members of shutter as specified in SSR Part-I section 8 clause 8.24(b) complete all as specified and directed. |
| 60 | S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 61 | M&L for 35mm thick well seasoned 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass etc. (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred bead for securing gauge etc size of members of shutter as specified in SSR Part-I section 8 clause 8.24(a) complete all as specified and directed. |
| 62 | S&F 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed. |
| 63 | S&F 150mm long aluminium anodised of extruded section barrel tower bolts complete all as specified and directed. |
| 64 | S&F 150mm long alumiunium handles cast type anodised complete all as specified and directed. |
| 65 | S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and as directed. |
| 66 | S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with 150mm overall length of cover plate complete all as specified and directed. |
| 67 | M & L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer on wooden surfaces complete all as specified and directed. |
| 68 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed. |
| 69 | S&F Steel work in tubular trusses including special shaped washer etc. complete usingERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240.complete all as specified and as directed. |
| 70 | S & F rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E-250 quality-A) complete all as specified and as directed. |
| 71 | S&F rolled mild steel Fe-410w (Gde-E-250) quality \"B\"Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and havy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified. |
| 72 | Dismantling framed steeltrusses span n.exc 10m complete all as specified and as directed |
| 73 | Fixing only Steel work intrusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240.complete all as specified and as directed |
| 74 | M&L for preparation of newlypainted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 75 | M&L forprepraration of old painted surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applyingone coat of synthetic enamel paintcomplete all as specified and directed. |
| 76 | S&F indoor or window frameof any descriptionwith aluminum sections, coloured powder coating not less than 50micron, and fixing in positions including all necessary cleats, lugs, beading, and jointing arrangements, complete all specified & directed. |
| 77 | M&L for Anodised aluminium powder coatedslidingwindowand ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc including all fitting . complete all as specified |
| 78 | S&F sheet glass 4.8mm thick ordinary quality and glazing with oil putty in squarenot exc 0.50 Sqm in each pane complete all as specified and as directed. |
| 79 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width or aperture 1.40mm complete all as specified and directed. |
| 80 | S&F 4mm thick ply wood grade BWR (type BB) fixed with screws to the timber fram work as on wall including dismantling boarding , any description, fixed in any position with nails complete all as specified. |
| 81 | Dismantling timber scantlings 40 sq. cm and over in section, in unframed work and in any position complete all as directed. |
| 82 | M&L for well seasoned 2nd class hard wood in scantling, clean sawn timber framed work complete all as specified and directed. |
| 83 | S&F 0.63mm plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip, wall cladding and straight flashings (length and girth as fixed) with grade of zinc coating 275complete all as specified and directed. |
| 84 | Ditto all as per Sl item No. 84.00 here-in-above but except sheeting.complete all as specified and directed. |
| 85 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, andgetting out in hard/dense soil complete all as specified and directed. |
| 86 | M&L for cement concrete Type C2 , 1:3:6 (Using 40mm graded aggregate) in post holes.complete all as specified and directed. |
| 87 | S&F, angle iron (Fe-310) as in posts, struts in fencing,gate including cutting top to shape required, drilling holes, notching for wire etc complete all speciified and directed |
| 88 | S&F steel flat iron including necessary drilling hole bolting or reveting etc and similar work complete conforming to Fe -290 Gde E - 165 complete all speciified and directed |
| 89 | Supply only Chain link MS galvanisd fencing, any size or type weighting not less than 2.80 Kg/Sqmcomplete all as specified and directed. |
| 90 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. |
| 91 | M&L forprepraration of new or untreated surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applyingone coats of synthetic enamel paint over a coat of red oxide primer for steel section above false ceiling.complete all as specified and directed. |
| 92 | Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5m in depth for foundation of laying of pipe etc, not exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and as directed. |
| 93 | Returning filling in including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and as directed. |
| 94 | M&L for PCC M-15 grade (Nominal mix) using 20mm graded crushed stone aggregate in coping complete all as specified and directed. |
| 95 | M&L for 20mm thick damp proof course in cement mortar 1:2 using water proofing compound @2% by weight of cement or as per manufacture instruction to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. (Note: WPC will be measured and paid separately here-in-after) |
| 96 | Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and as directed. |
| 97 | M&L for Hardcore of broken stone or boulder ofgauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 98 | Supply of Integral WaterProofing Compound ISI Marked. |
| 99 | M&L for precastcement concrete chequred tiles (ISI approved) of size 200mm x200mm x25mm thick, set and jointed and pointed in neat cement slurry in floor with grey cement and pigment all as specified and directed. |
| 100 | M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvesincluding supports, overhangs, etc. also splays between floors and beams, etc rough finised surface of concrete complete all as specified and directed |
| 101 | M&L for 75 mm thick PCC M15 grade (Nominal mix) using 40mm graded crushed stone aggregate as in sub base complete all as specified and directed. |
| 102 | M&L 25mm thick plain cement concrete M15 grade (Nominal mix) using 20mm graded crushed stone aggregateasin floor, finishes even and fair to receive floor tiles complete all as specified and directed. |
| 103 | M & L for 20mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor tiles etc complete all as specified and directed. |
| 104 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 105 | M&L for machine cut kota stone slab20-25mm thick in riser of steps,skirting,dado and pillarover and including 10mm thick cement mortar backing in cm (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and directed. |
| 106 | S&F harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed. |
| 107 | M&L forwall care putty not less than 2-3 mm thick ofnewly plastered surface of wall as per manufacturer instructions or as complete all as specified and directed. |
| 108 | S&F 2nd class hardwood plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 109 | S&F sheet glass 3mm thick, ordinary quality and glazing with oil puttyin squarenot exc 0.5 sqm in each pane complete all as specified and as directed. |
| 110 | S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm complete all as specified and directed. |
| 111 | S&F exposed GI powder coated snap grid frame work for false ceiling of grid size 600 x600mm comprising of wall/cleat angle of size 25 x25 x0.35mm and main/cross tee of size 24 x38 x0.70mm with 4mm dia GI wire as suspender and including 4mm thick Plain E-Boardincluding fixing arrangement from steel truss of any type and applying two coats of oil bound distemper over one coat of chalk whiting complete all as specified and directed. |
| 112 | M&L for preparation of new zinc (or galvanised) surfaces to receive painting by coating with mordant solulation including washing and cleaning etc and applying two coats of red roof paint over a coat of red oxide. |
| 113 | S & F mild steel flat iron as in hold fast including screwing or welding complete all as specified and directed |
| 114 | Supply and fixed 2nd class HW small fittings such as brackets of any type, latch and hing block, saved door and window stops and the like including all necessary labours articles n exc 200 cu cm each.complete all as specified and directed. |
| 115 | S&F 75mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed. |
| 116 | S&FMS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete fixed in floor complete all as directed. |
| 117 | M&L for 2nd class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed |
| 118 | S & F of ACP(Aluminium composite panel) false ceiling made out of aluminium 40x25mm rectangular channel grid of desired/require size and fixing of 3 mm thick ACP white colour/desired shade with screws,complete with applying weathher silicon in the grooves between the planks including necessary scaffolding at all hight . complete all as specified and directed |
| 119 | E/M work |
| 120 | Taking down carefully unserviceable aluminum/ copper point wiring (light/ fan/ socket/ power) complete including fixture & fitting such as switches, sockets, ceiling roses regulators, lamp holder etc. but excluding light fittings & fixture and exhaust fans etc removing and making good disturbed surfaces of wall/ceiling etc completeall as specified and directed. |
| 121 | Material and labour for point wiring surface type with two single core 1.5 Sq mm (nominal area) FRLS PVC insulated and unsheathed, multi-stranded, copper conductor cable in and including suitable size PVC casing capping with all fittings and fixing accessories and suitable size PVC box for mounting switches, regulator etc includingmulti-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connecting to light fitting/fans etc completeall as specified and directed for following :- (Colour code to be followed) |
| 122 | One light/fan point controlled by one, one way switch |
| 123 | One celling / exhaustfan point controlled by one, one way switch. |
| 124 | One socket outlet 5 Amps 5 pin on independent board |
| 125 | One socket outlet 5 Amps 5 pin on same board with other switches |
| 126 | All as per item No. 122 here in before but with cable size 2.5 Sqmm and earth continuity conductor of 2.5 Sqmm size for one 5 pin 15 Amps socket out let on independent board complete all as specified and directed. |
| 127 | S&Fmodular switch piano, 6 Amps, single pole, one way complete all as specified and directed. |
| 128 | S&F modularsocket outlet 2/3 Pin 6 Amps combined 2 module complete all as specified and directed. |
| 129 | S&F modular socket multipurpose 3 pin 16 Amps and 3 pin 6 Amps combined 2 module complete all as specified and directed. |
| 130 | S&F Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 131 | S&Fmodular switch piano, 16 Amps, single pole, one way complete all as specified and directed. |
| 132 | S&F modular white cover with frame for fixing of 12 module. |
| 133 | S&F modular white cover with frame for fixing of 6 module. |
| 134 | S&F modular white cover with frame for fixing of 3 module. |
| 135 | S&F modular white cover with frame for fixing of 2 module. |
| 136 | S&F blank spacer plate for single module. |
| 137 | S&F modular electronic fan regulator rotary stepped type 120W, 240V, single phase, two module and connecting up complete all as specified and directed. |
| 138 | Taking downold unserviceable main switch/ DBs/ MCB DBs with MCB including making good the disturbed surface complete as directed. |
| 139 | S&F sheet metal enclosure for MCB’s distribution board, 240 Volts, 8 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door verticle for breaking capacity 10 KA complete all as specified and directed.(Make: Havells cat part No. DHDPSHODRW 08 or as per list approved makes enclosed hereinafter) |
| 140 | S&F sheet metal enclosure (for DB\"s when MCBs to be used), single pole and neutral double door, 12 way, 240 Volts in concealed ( Make - Indo Asian / Legrand / Havells/Schneider |
| 141 | S&F MCB single pole and neutral 32 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed. |
| 142 | S&F MCB single pole 06 to 32Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed. |
| 143 | S&F PVC Board (30 x 25 x 5) cm depth medium quality ISI marked complete all as directed. |
| 144 | Taking down LED tube light fitting kept in safe custody for refixing to its original position including provision of cable from ceiling rose or connected to light.complete all as specified and directed. |
| 145 | S&F LED light fitting 1 x 22 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose.complete all as specified and directed. |
| 146 | Refixing ceiling tube light received from item No 17 here in before and connecting up including provision of cable from ceiling rose or connector to light.complete all as specified and directed. |
| 147 | Taking down old unserviceable service cableincluding batten/suspending wires complete all as directed. |
| 148 | Taking down ceiling/exhaust fan including dismantling all necessary electrical connections to facilitate repairs to ceiling/wall complete all as directed. |
| 149 | Hanging only/ Refixing ceiling/exhaust fan removed under item Srl No 150 above and connecting upincluding provision of cable from ceiling rose or connector to fan complete all as directed. |
| 150 | S&F Service wire connection with one twin core 10 sq mm, 2 core, 1100 volts grade heavy duty flat or circular cable, multi stranded aluminium conductor, PVC insulated served with inner sheathing of PVC tape armoured, suspended by insulating hangers not more than one mtr apart incl 4mm dia GI suspension wirecomplete all as specified and directed. |
| 151 | S&F ceiling fans 1200 mm sweep, 240 Volts, 50HZ, 3 blade withstandard super silent motor including provision of 3 core flexible copper conductor cable of size 23/0.19 from ceiling rose to ceiling complete fixing arragement etc complete all as specified and directed. (Make: Havells Cat No. SS 390 or equivalent in Usha/Havells/ Bajaj/ Orient) |
| 152 | S&F building security light fitting new generation energy saving & environmental friendly long life versatile pressure die cast aluminium IP-66 high power LED light 20 watt including suitable size of wall bracket and connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. (Make: Havells Endura Pearl Cat No. ENDURAPEARLSL20WLED757SASYTOPC or equivalent in Bajaj/Philips/Crompton) |
| 153 | Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth wire 4mm dia by means of galvanized iron or steel bolts nuts check nuts and washers and other end connected with earthing testing point including providing suitable testing points as directed including funnel, watering pipe of 20mm bore, light grade galvanized iron pipe, wire mesh charcoal of coal dust and common salt in alternative layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1 cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work in hard/dense soil as required complete all as shown in electrical plate No 3 of MES Schedule Part I and testing on completion all as specified and as directed. (Note: Earth strip beyond 7.5 m length will be measured & paid separately) |
AI Tender Summary
Tender Timeline
Jun 18, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 28, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 30, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender