Construction Of Store Room Cum Godown For Equipment Of Conservancy Staff At Kulti Office Under Asansol Municipal Corporation.- 1 Dismantling All Types Of Masonry Excepting Cementconcrete Plain Or Reinforced, Stacking Serviceablematerials At Site And Removing Rubbish As Directedwithin A Lead Of 75 M.In 2Nd Floor ( Rate =Rs ( 447+50+50 ) =Rs 547.00 ) 2 Hire And Labour Charges For Shuttering With Centering And Necessary Staging Upto 4 M Using Approved Stout Props And Thick Hard Wood Planks Of Approved Thickness With Required Bracing For Concrete Slabs, Beams And Columns, Lintels Curved Or Straight Including Fitting, Fixing And Striking Out After Completion Of Works ( Upto Roof Of 2Nd Floor ) ( A ) 25 Mm To 30 Mm Thick Wooden Shuttering As Per Decision & Direction Of Engineer-In-Charge.D ) Extra For Works Beyond The Roof Of Ground Floor Per Additional Floor ( 328+18+18 ) 3 Reinforcement For Reinforced Concrete Work In All Sorts Of Structures Including Distribution Bars, Stirrups, Binders Etc Initial Straightening And Removal Of Loose Rust ( If Necessary ) , Cutting To Requisite Length, Hooking And Bending To Correct Shape, Placing In Proper Position And Binding With 16 Gauge Black Annealed Wire At Every Intersection, Complete As Per Drawing And Direction. ( A ) For Works In Foundation And Upto Roof Of Ground Floor / Upto 4 M ( I ) Tor Steel / Mild Steelmanufacturers Not Specified ( 53045.73+430.00+430.00=49200.99 4 Ordinary Cement Concrete ( Mix 1:1.5:3 ) With Graded Stone Chips ( 20 Mm Nominal Size ) Excluding Shuttering And Reinforcement If Any, In 2Nd Floor As Per Relevant Is Codes. ( I ) Pakur Variety ( 5343.16+95+95 ) 5 Brick Work With 1St Class Bricks In Cement Mortar ( 1:4 ) ( B ) Superstructure ( 5235.36+111+111 ) 6 Plaster ( To Wall, Floor, Ceiling Etc. ) With Sand And Cement Mortar Including Rounding Off Or Chamfering Corners As Directed And Raking Out Joints Including Throating, Nosing And Drip Course, Scaffolding / Staging Where Necessary ( 2Nd Floor ) . ( Ii ) With 1:6 Cement Mortar ( C ) 15 Mm Thick Plaster ( 4+4 ) 7 ( B ) 20 Mm Thick Plaster ( 1:6 ) ( 151.57+4+4=159.57 ) 8 Neat Cement Punning About 1.5Mm Thick In Wall, Dado, Window Sill, Floor Etc. 9 M.S. Gate Of Jail Type As Per Approved Design Made Of Strong M.S. Frame Work, Intermediate Stiffeners And Round / Square Bars Or Angles. M.S. Sheet ( Not Less Than 14 Gauge ) Gussets, Cleats Etc. Including Necessary Riveting, Bolting, Welding, Locking And Hanging Arrangements, Fitting And Fixing Complete As Per Direction Of The Engineer-In -Charge.In Ground Floor. ( Add Extra @ 1% For Each Addl. ) ( 10090+100.9+100.9 ) 10 M.S. Structural Works In Columns, Beams Etc. With Simple Rolled Structural Members ( E.G. Joists, Angle, Channel Sections Conforming To Is: 226, Is: 808 & Sp ( 6 ) - 1964 Connected To One Another With Bracket, Gussets, Cleats As Per Design, Direction Of Engineer-Inchargecomplete Including Cutting To Requisite Shape And Length, Fabrication With Necessary Bolting, Metal Arc Welding Conforming To Is: 816- 1969 & Is: 1995 Using Electrodes Of Approved Make And Brand Conforming To Is:814- 2004, Haulage, Hoisting And Erectionall Complete. The Rate Includes The Cost Of Rolled Steel Section, Consumables Such As Electrodes, Gas And Hire Charge Of All Tools And Plants And Labour Required For The Work Including All Incidental Chages Such As Electricity Charges, Labour Insurance Charges Etc.I ) For Structural Members Of Specified Sections Weighing Less Than 22.5 Kg. / M ( 72603.00*1.015 ) =73692.05 11 M.S. Structural Works With Hollow Sections ( Square Or Rectangular Shape ) Conforming To Is: 806-1968 & Is:1161-1998 ) Connected To One Another With Bracket, Gusset, Cleat As Per Design, Drawing & Direction Of Engineer-In-Charge Complete Including Cutting Torequisite Shape & Size, Fabrication Including Metal Arc Welding Conforming To Is: 816-1969 & Is: 9595 Using Electrodes Of Approved Make And Brand Conforming To Is:814- 2004, Haulage, Hoisting And Erection All Complete. The Rate Includes The Cost Of All M.S. Hollow Section, All Consumables Such As Electrodes, Gas And Hire Charges Of All Tools And Plants And Labour Reqired For Execution And All Incidental Chages ( Such As Electricity, Labour Insurance ) Etc. Complete.Payment To Be Made On The Basis Of Calculated Weight Of Structural Memebrs Of Ms Holow Section As Specified In Relevent Is Code Infinished Work. Payment For Gusset, Bracket, Cleat May Be Made By Adding The Actual Weight Of Such Items With Weight Of Finished Structural Members. The Rates Are Considered For A Hight Of Erection 8 M. / 2Nd Floor Level From The Ground. Add 1.5 % Extra Over The Rate For Each Additional Floor Or 4M. Beyond The Initial 8 M. Or Partthereof. I ) For Roof Truss Works A ) Span Up To 12 Mtr ( 72316.00*1.015 ) 12 Supplying, Fitting & Fixing Zn-Al Alloy ( 55% Al & 45% Zn ) Coating Of 150 Grams Per Sq. Metre ( Followed By Colour Coated On Both Side ) Steel Sheet Work Having Minimum Yield Strength Of 550 Mpa Of Trapizoidal Profile Of Approved Make ( Excluding The Supporting Frame Work ) Fitted And Fixed With 55 Mm & 25 Mm Self Tapping Screw, Epdm Washer 16 Mm Dia & 3 Mm Th. Washer Etc. Complete With 150 Mm End Lap And One Corrugation Minimum Side Lap. ( Payment To Be Madeon Area Of Finished Work ) . ( I ) In Roof:-A ) With 0.5 Mm Thick Sheet 13 Galvanised Or Painted Wind-Tie Made Of M.S. Flats, Fitted And Fixed Complete Including Cost Of Necessary Fittings. ( A ) Made With 40 Mm. X 6 Mm. Flats 14 ( A ) Priming One Coat On Steel Or Other Metal Surface With Synthetic Oil Bound Primer Of Approved Quality Including Smoothening Surfaces By Sand Papering Etc. 15 ( B ) Priming One Coat On Timber Or Plastered Surface With Synthetic Oil Bound Primer Of Approved Quality Including Smoothening Surfaces By Sand Papering Etc. 16 A ) Painting With Best Quality Synthetic Enamel Paint Of Approved Make And Brand Including Smoothening Surface By Sand Papering Etc.Including Using Of Approved Putty Etc. On The Surface, If Necessary : ( A ) On Timber Or Plastered Surface :With Other Than Hi-Gloss Of Approved Quality- ( Iv ) Two Coats ( With Any Shade Except White ) 17 ( B ) On Steel Or Other Metal Surface :With Other Than Hi-Gloss Of Approved Quality- ( Iv ) Two Coats ( With Any Shade Except White ) 18 Removal Of Rubbish, Earth Etc. From The Workingsite And Disposal Of The Same Beyond The Compound, In Conformity With The Municipal / Corporation Rules For Such Disposal, Loading Into Truck And Cleaning The Site In All Respect As Per Direction Of Engineer In Charge 19 Led Tube Light ( Philips Make ) 18 Watt 20 Distn. Wiring In 22 / 0.3 ( 1.5 Sqmm ) Single Core Stranded Fr Pvc Insulated & Unsheathed Single Core Stranded Copper Wire ( Brand Approved By Eic ) In 19 Mm Bore, 3 Mm Thick Polythen Pipe ( For Horizontal & Vertical Run In Wall And Celing Portion Through Prelaid Polythen Pipe ) Complete With All Accessories Embedded In Wall To Light / Fan / Call Bell Points With Piano Key Type Switch ( Anchor Make ) Fixed On Sheet Metal ( 16 Swg ) Switch Board With Bakelite / Perspex ( Wall Matching Colour ) Top Cover ( 3 Mm Thick ) Flushed In Wall Incl. Mending Good Damages To Original Finish2x22 / 0.3 ( Ph. & N ) And 1X22 / 0.3 As Eccaverage Run 6 Mtr 21 Supplying And Delivery Of 1200Mm Sweep Single Phase 60 / 70Watt 5 Star And Having 300Mm Down Rod 1.1 Mm Thick Aluminium Blade Conforfing Is :374 2Mm Shank Thickness Ceiling Fan Of Havells / Cg Make. 60Watt 22 Supply & Fixing 240 V, 4 Nos. 6A, Plug Socket With Separate 4 Nos. 6 A Piano Key Type Switch, Indicator & 16A Kit-Kat Flush Type Fuse ( Brand Approved By Eic ) On Sheet Metal Switch Board Embedded In Wall Incl. S & F 240X200x65mm Ms ( 16Swg ) Switch Board And Bakelite / Perspex Top Cover Of 3Mm Thick By Brass Screws After Making Housing For Switch By Cutting Bakelite / Perspex Cover And Making Necessaryconnections As Required 23 Fixing Only Exhaust Fan After Making Hole In Wall And Making Good Damages And Smooth Cement Finish Etc. As Practicable As Possible And Providing Necy. Length Of Pvc Insulated Wire And Making Connection For Exhaust Of Following Diameter:45 Cm ( 18 ) 24 Distn. Wiring With 2 X 36 / 0.3 ( 2.5 Sqmm ) Single Core Stranded Copper Conductor Pvc Insulated And Unsheathed Copper Wire ( Brand Approved By Eic ) In 19Mm Dia 3 Mm Thick Polythene Pipe With 1X22 / 0.3 ( 1.5Sqmm ) Pvc Insulated And Unsheathed Coper Wire As Ecc, Complete With All Accessories Embedded In Wall ( For 15 A Plug Point / Exhaust Fan Point )
