Estimate For The Cost Of Renovation Of H.A Quarters At Division Compound Peermade In Azhutha Range During 2022 -23. Estimate For The Cost Of Renovation Of H.A Quarters At Division Compound Peermade In Azhutha Range During 2022 -23.
Tender Value
7.19 Lakhs
Estimated cost
Bid Submission
15 Jun 2022
0 days left
EMD
10785
Bank guarantee accepted
Document Fee
1700
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
peermade → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Estimate For The Cost Of Renovation Of H.A Quarters At Division Compound Peermade In Azhutha Range During 2022 -23. Estimate For The Cost Of Renovation Of H.A Quarters At Division Compound Peermade In Azhutha Range During 2022 -23.
BOQ
| Sl. No. | Item Description |
| 1 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., includingcutting, hoisting, fixing position and applying a priming coat of approved steel primer, including weldingand bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 2 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation asapproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet andpolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum toavoid scratches during transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shape wherever required. |
| 3 | 3 labor--Engaging second class Masons for dismantling brick work over shade andporch tile at step ,demolishingunderside car porch slab plastering |
| 4 | Engaging Carpenter-for maintains thedoors windows and removing damagedshutters of windows and ventilators |
| 5 | Engaging Fitteer-for maintains theelectrical and plumbing works |
| 6 | Engaging Mate-for clearing premiseand washing cleaning and dusting of old wallsurface |
| 7 | Engaging Coolie-for assist fittercarpenter mason andmate |
| 8 | Wood Work -Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below for doors |
| 9 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood |
| 10 | Providing and fixing glazed shutters for door, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. Pressed butt hinges bright finished of required size with necessary screws.Second class teak wood35 mm thick |
| 11 | Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Kiln seasoned and chemically treated hollock woodProviding and fixing panelled or panelled and glazed shutters for doors, windowsand clerestory windows fixing with butt hinges of required size with necessaryscrews, excluding panelling which will be paid for separately, all complete as perdirection of Engineer-in-charge. (Note:- Butt hinges and necessary screws shallbe paidseparately)Kiln seasoned and chemically treated hollock wood35 mm thick shutters |
| 12 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laidin required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling thejoints with fine sand etc. all complete as per the direction of Engineer-in-charge. |
| 13 | Concrete-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 14 | Sanitary fittings-Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size withplastic moulded frame of approved make and shade with 6 mm thick hard board backing :Oval shape450x350 mm (outer dimensions) |
| 15 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 16 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total lengthof 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms |
| 17 | Electrical fittings-Supply Conveyance, installation, testing and commissioning of 36/40W LED street light output greaterthan 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with powerfactor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-castPowder coated housing,acrylic cover complete with THD less than 10%, power factor greater than 0.98,RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be producedmentioning chip manufacturer) |
| 18 | Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm withspecials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988,fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity ofcopper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular typemetal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in theswitch boards and DB\"s shall be tinned and the wires shall be drawn and fixed along the periphery of thebox using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Single Control light point with 6A, plate ceiling rose - Short point |
| 19 | Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988,fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity ofcopper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular typemetal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in theswitch boards and DB\"s shall be tinned and the wires shall be drawn and fixed along the periphery of thebox using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Combined plug point with 6 A, 5 pin plug socket controlled by 6 A, switch in the same switch board as that of lightpoints |
| 20 | Glass panes-Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick indoors, windows and clerestory window shutters. ( Area of opening for glass panes excluding portioninside rebate shall be measured). |
| 21 | Plastering-6 mm cement plaster 1:3 ( 1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. |
| 22 | Painting-Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm |
| 23 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint ofapproved brand and manufacture for doors windows and car porch iron members |
| 24 | LS amt for electrical items such as LED tube 6 nos and other fittings |
| 25 | LS amt for furniture fittings and other items |
| 26 | GST |
| 27 | Unforssen |
AI Tender Summary
Tender Timeline
Jun 07, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 15, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 17, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender