|
| 1 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 2 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 3 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 4 | 250x16 mm |
| 5 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 6 | 150x10 mm |
| 7 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 8 | 125 mm |
| 9 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. |
| 10 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC \"C\" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the \"C\" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer\"s specification & drawing. |
| 11 | 30 mm thick plain PVC door shutters |
| 12 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 13 | 12 mm cement plaster of mix : |
| 14 | 1:4 (1 cement: 4 fine sand) |
| 15 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : |
| 16 | Water thinnable cement primer |
| 17 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : |
| 18 | Two or more coats on new work |
| 19 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 20 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: |
| 21 | One or more coats on old work |
| 22 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 23 | One or more coats on old work |
| 24 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 25 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 26 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 27 | For thickness of tiles 10 mm to 25 mm |
| 28 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 29 | W.C. pan with ISI marked white solid plastic seat and lid |
| 30 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 31 | White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 32 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : |
| 33 | Size 600x450x200 mm |
| 34 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 35 | Flexible pipe20.1.1) 32 mm dia |
| 36 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 37 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 38 | 20 mm nominal dia Pipes |
| 39 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 40 | 45 cm length23.1.1) 15 mm nominal bore |
| 41 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 42 | 15 mm nominal bore |
| 43 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 44 | 15mm nominal bore |
| 45 | Providing and fixing PTMT grating of approved quality and colour. |
| 46 | Circular type26.1.1) 100 mm nominal dia |
| 47 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 48 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : |
| 49 | For fixed portion28.1.1) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 50 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)28.2.1) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 51 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 52 | Pre-laminated particle board with decorative lamination on both sides |
| 53 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 54 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 55 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 56 | Providing and fixing FROSTED Glass in Aluminium door, windows, ventilator shutters and partitions etc. with EPDM robber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (cost of aluminium snap beading shall be paid in basic item): |
| 57 | With Frosted glass panes of 5.50 mm thickness |
| 58 | Providing and fixing sliding arrangement in shutter by rollers to run inside C or E aluminium channel section. (Payment of C or E channel shall be made separately). |
| 59 | Providing and laying hollow cement concrete block walling upto floor five level 200mm thick consisting of hollow block of size 400x200x200mm of mix 1:3:6(1 :cement 3 :coarse sand 6 :graded stone aggregate 10mm nominal and down size) having a crushing strength of 3.5N/sqmm at 28 days as per IS:2185 (part-I) 1979 laid in cement mortar 1:6(1 :cement 6 :coarse sand) upto floor five level. |
| 60 | Providing and fixing CP brass Health Faucet with 8 mm dia, 1.20 meter long flexible tube & wall Hook ofmake Jaquar or equivalent (Code No.ALD- 573) of good quality as per the direction of Engineer-in-charge. |
| 61 | Providing and fixing UPVC Nahani trap with jali including cost of cutting and making good the walls and floors of approved quality etc. as per direction of Engineer-in-Charge. |
| 62 | 110 x 75 mmdia |
| 63 | Providing and fixing soil, waste and vent pipes : with UPVC pipe conforming to IS : 13592 Type B including jointing with seal ring conforming toIS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes |
| 64 | 110 mm dia |
| 65 | 75 mm dia |
| 66 | Providing and fixing PVC moulded fittings/ accessories for PVC pipes including jointing with seal ring. i) PVC Door bend |
| 67 | 110 mm dia |
| 68 | 75 mm dia |
| 69 | Providing and fixing PVC moulded fittings/ accessories for PVC pipes including jointing with seal ring. i) PVC Plain bend |
| 70 | 110 mm dia |
| 71 | 75 mm dia |
| 72 | Providing and fixing single lever Surgical purpose Elbow action pillar cock with extended operating Lever withour popup waste system of make Jaquar (code No. FLR-5031N) or equivalent as desired by the Engineer in charge. |
| 73 | 15mm nominal bore |
