|
| 1 | M&L for15 mm thick Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like bedded in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite with and including Dismentling of old stone slabs and tilesof any description or thickness in floors, approns etc,laid bedded and pointedin any mortar complete all as specified and directed. |
| 2 | Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground level complete all as specified and directed |
| 3 | M&L for 25 mm thick cement concrete 1:2:4 type B-0(using 12.5 mm graded crushed stone aggregate) as in sunken floor finished even and smooth using extra cement with using water proofing compound as per manufacturer\"s instructions complete all as specified and directed.Note:- Water proofing compound shall be measured and paid seperately under respective item of Schedule \"A\"/BOQ. |
| 4 | M&L for providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing membrance comprising of the following for NON approachable roofs complete all as specified and directed. (i) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @0.30 Kg/sqm on top f dry surface of finished cement mortar plaster or cement concrete surfaces. (ii) One coat of hot blown bitumen of grade 85/25 @ 1.2 Kg/sqm shall be applied over primed surfaces. (iii) Applying of APP based polymeric membrance minimum weighing 3 Kg /sqm & minimum 3mm thickness reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified with overlap of 100mm and the overlap shall be sealed by flame.(iv) Applying two coats of aluminum paint on top of membrane @ 1010kg/ sqm for each coat. Note:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorized applicator of manufacturer approved by GE. |
| 5 | M & L rendering 20mm thick on fair faces of brick work or concrete surfaces in CM 1:3 with liquid water proofing Compound as per manufacturers\"s instructions complete all as specified and directed. Note:- Water proofing compound shall be measured and paid for seperately under respective item of Schedule \"A\" BOQ. |
| 6 | Supply only Liquid water proofing compound ISI Marked (used 200 ml per bag of cement) complete all as specified and directed. |
| 7 | M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregates) in copings, kerbs, channels, water through and the like including weathering, slightly rounded or chamfered angles and throating as directed chamfered necessary for work complete all as specified and directed. |
| 8 | M&L for Roughening surfaces of old concrete/ brick surfaces by picking, sweeping clean and washing down with water to remove dust etc and applying two coat of hot blown bitumen 85/25 grade 1.2 kg /Sqm per coat over and including Rendering 15mm thick in CM (1:3) on fair faces of concrete surface and finishing the surfaces even and smooth without using extra cement using water proofing compound as per manufacturer\"s instructions including 50 micron thick black polythene film, for sunkenslab treatmentcomplete all as specified and directed. Note:- Water proofing compound shall be measured and paid for seperately under respective item of Schedule \"A\". BOQ |
| 9 | M & L for providing plain cement concrete, type E-2, 1:5:10 (using 40 mm graded brick aggregates as in sunken, filling and mass concrete complete all as specified and directed. |
| 10 | Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in CM 1:4 complete including dismantling of existing floor tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as directed. |
| 11 | All as per item No 11as above but on vertical surface such asdado, skirting etc including 10 mm plaster rendering in cm (1:4) complete all as specified and directed. |
| 12 | Vitrified ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:6 complete and dismantling of existing floor tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as directed. |
| 13 | All as per item No 13as above but on vertical surface such asdado, skirting etc including 10 mm plaster rendering in cm (1:4) complete all as specified and directed. |
| 14 | Glazed ceramic coloured tiles of size 300 mm x 450 mm x 7mm /350 mm x 450 mm x 7mm /250 mm x 250 mm x 7mmthick as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 10 mm thick rendering in cement mortar 1:4 finished rough surface to receive tiles including dismantling of existingwall tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as directed. |
| 15 | Removing demolished material out of defence land depositing at contractor\"s own arrangement complete all as specified and directed. |
| 16 | Taking down shutterexc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description.complete all as specified and directed. |
| 17 | Taking down shutters of any descriptionexc 1 sqm & n. exc 2 sqmeach complete all as specified and directed |
| 18 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm but n. exc. 4.00 sqm each complete all as specified and directed. |
| 19 | Taking down chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each complete all as specified and directed. |
| 20 | S&F 40 mm thick Flush shutters, solid coreconstruction, with block board core and plywood face panels, commercial type on both sidesd.complete all as specified and directed. |
| 21 | S&F factory made glazed and skelton shutters 35mm thick first class hard woodopen rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars, any numbers , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I 2009 section 8, clause 8.24 (a)complete all as specified and directed. |
| 22 | S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube as per specification , drawings and asspecified in SSR Part-II 2020 complete all as specified and directed. |
| 23 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet onback face, supplying & fixing in frame at site as per specification & drawing ®complete all as specified and directed. |
| 24 | S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed. |
| 25 | S&F 100 mm sizemild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 26 | S&Faluminiumhandles, cast type, anodised 150 mm size completeall as specified and directed. |
| 27 | S&F floor door stopper double leg of aluminium alloy bodyof 70 mm length with aluminium base plate of size 50 mm x 40mm complete all as specified & directed. |
| 28 | S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed allas specified and directed. |
| 29 | S&F in reppair 150 mm, mild steel ordinary rat tail rod pattern spring including roller and roller plate including necessary welding if requriedcomplete all as specified & directed. |
| 30 | S&F in repair 18 to 20 mm thick solid PVC Board for cupboard/cabinet shutters with one side 1 mm thick printed PVC sheet other side plain PVC sheet of approved pattern as per specification and drawing and including necessary beading in matching colour, magnetic ball catcher, 1 brass 2 lever lock of 50 mm size complete all as specified and directed. |
| 31 | S&F in repair 18 to 20 mm thick solid PVC Boardfor cupboard/cabinet partitions/frame as per specification and drawing and necessary beading in matching colourcomplete all as specified and directed. |
| 32 | S&F 125 mm long hasp & staple safty type aluminium anodisedwith mild steel hinge pinincluding bolt to hinge plate and fixed with screws complete all as directed. |
| 33 | S&Fbrasshandles, cast type, polished bright 100 mm size completeall as specified and directed. |
| 34 | S&F in repairgalvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized steel wire staples complete all as specified and directed. |
| 35 | S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm completeall as specified and directed. |
| 36 | S&F MS angle iron work as in door frame work conforming to Fe 290(Gde E-165) including tie rod, hinges including one shop of red oxide primer etc. completeall as specified and directed. |
| 37 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beadsincluding punching or drilling out old glazing pins/spring clips etc complete all as specified and directed. |
| 38 | M&L for 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 39 | M&L for 4 mm thick figured glass pin headed type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 40 | M & L for At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same etc. complete all as specified and directed. |
| 41 | Taking downcement or cement lime plaster of any description including racking out joints, hacking for keys , scrubing down with water etc, complete all as specified and directed. |
| 42 | M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4mixed withwater proofing compound as per manufacturer\"s instruction, finished fair and even without using extracement complete all as specified and directed. Note :- WPC shall be measured and paid forseprately as \"supply only\" under respective item of sch A/ BOQ. |
| 43 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extracement)complete all as specified and directed. |
| 44 | M & L for 10 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:3 finished even and smooth (without using extracement)complete all as specified and directed. |
| 45 | M&L for 5 mm thick cement plaster in 1:3 cement mortar, on concrete ceiling surface finished even and smooth without using extra cement, complete all as specified and directed. |
| 46 | M & L Preparation of old surfaces of walls, plastered on un plastered by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss & efflorescent salts, removing all vegetation growth and trading oil and greasy spots and applying one coat of white wash on old white washed surfaces of walls complete all as specified and directed. |
| 47 | All as per itemNo 53 above but on Ceiling Surface,Complete all as specified and directed. |
| 48 | M&L for preparing old surfaces of walls plastered or un-plastered by brooming down with steelor wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of distemper oil emulsion on old prepared surfaces of walls completeall as specified and directed. |
| 49 | M&L for preparation of old decorated plastered or unplastered surfaces of ceiling, cornices etc by brooming down or steel wire brushing downscrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, and applying one coat of oil bound distempercomplete all as specified and directed. |
| 50 | M&L for complete removal of existing treatement by scraping, washing, rubbing down or stopping distempered or painted surfaces etcof walls plastered or un-plastered & removing all vegetation growth, cleaning & applying of Birla/JK white wall putty approx 1 mm thick in two layer as per manufacturer\"s instruction on existingprepared surface and make the surface smooth by rubbing with sand papers etcand applying two coats of oil emulsion distemper overa coat of alkali resistant primercomplete all as specified and directed. |
| 51 | M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 52 | M&L for preparing of new steel surfaces over 10cm width or girth andapplying one coat of synthetic enamel paint on steel surfaces over primed completeall as specified and directed. |
| 53 | M&L for preparing of old painted steel surfaces over 10cm width or girth and making good with & including by necessary red lead puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of synthetic enamel paint on old prepared surfaces ofsteel completeall as specified and directed. |
| 54 | M&L for preparing of old painted wooden surfaces over 10cm width or girth and making good including knotting and stopping,cleaningetc complete by necessary puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of synthetic enamel paint on old prepared surfaces of wooden completeall as specified and directed. |
| 55 | M&L Applying one coat of cement base paint over and after preparation of old painted surface after preparation of surface including brooming down loose partical, removing of smoke moulds and unwanted vegetation from wall, facia, parapet etc, completeall as specified and directed. |
| 56 | M&L Applying Two coat of cement base paint after preparation of old painted surface including brooming down loose partical, removing of smoke moulds and unwanted vegetation from wall, facia, parapet etc, completeall as specified and directed. |
| 57 | M & L for complete removing of existing treatment and preparation ofplastered surface and applying of Birla/JK white wall putty approx 1 mm thickas per manufacturer\"s instruction on prepared surfaceand make the surface smooth by rubbing with sand papers etc andapplying Two coats ofweather proof exterior paint silicon basedover a coat of primercomplete all as specified and directed. |
| 58 | M&L for preparing of new plastered surface on wall and applying two coats of Oil bond distemperover a coat ofalkali resitance primer over 3 mm thick wall care putty in two layer on plastered surface completeall as specified and directed. |
| 59 | S&F in counter top wash hand basin coloured oval type 550x445 mm fixed over granite slab ofAppropriatesize including brackets, PVC connection waste pipe waste coupling etc complete all as specified andas directed . Make: Parryware / Prayag or other equivalent makes from Jaquar/Hindware and as approved by GE. Note Graniteslabwill bemeasuredand paidseparately under respective item of Sch A/BOQ. |
| 60 | S&F in repair white vitreous China wash down water closet pan (pedestal) pattern, and trap(excluding) fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. with and including plastic water closet seat covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and 15mm dia chromium plated brass washing jet fixed to water closet with 15mm dia and 1.2m to 1.5m long flexible pipe with chromium plated spring type cover complete with fixing arrangement fancy look complete all as specified and directed. |
| 61 | S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet,integral foot rest (excluding flushing cistern and flush pipe) & including CI trap & connecting fitting as required set inplain cement concrete (1:3:6) type C-1and connecting to flushing cistern and trap & connecting fittings as required and making good to floor, complete all as specified and directed. |
| 62 | S&F in repairKitchen Plate rack with & including shelves and hanging arrangements for utensil for kitchen ,made of stainless steel sheet 0.63 mm thick,size 900 mm x 600mm x 250mmcomplete all as specified and directed.Cat part No:-. KPR-311 of Make Blue Star or other equivalent make of pryag / Nirali complete all as specified and directed. |
| 63 | S&F in repairsinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with & including one waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement ,with PVC coupling, PVC waste pipe 40mm bore 750mm long complete all as specified and directed. Cat part No:-. BSSBSD-52 of Make Blue Staror other equivalent make of pryag / Nirali complete all as specified and directed. |
| 64 | S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andPVC flush pipe 32 mm borecomplete all as specified and directed |
| 65 | S&F in repair vitreous china wash hand basin (flat back) of size 550x400mmincluding one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector,MS brackets 2 numbers including cutting for and pinning in ends of brackets completeall as specified and directed. |
| 66 | S&F in repair for 600x450mm beveled edge looking mirror of selected quality glass 4 mm thick mounted on 6mm thick AC building board or commercial ply woodand fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. |
| 67 | S&F in repair bib cock long body with flange , fancy type,brass,chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orGI socket complete all as specified and directed. |
| 68 | S&F in repair fancy typeangle cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed. |
| 69 | S&F in repair fancy type, stop cock regular body 15 mm nominal bore with flange, brass, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule orGI socket complete all as specified and directed. |
| 70 | S&F in repair pillar taps, brass, with capston heads, fancytype chromium plated, screwed down high pressure with or without lettered \"Hot\" or \"cold\" with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make Prayag or other equivalent makes model in specified makes as approved by GE. |
| 71 | S&F in repair 125 mm size chromium plated brass shower rose with swivel joints and swivel arms for fixing with 15 mm pipe complete all as specified and directed. |
| 72 | S&F in repair towel rail ,D type, brass, chromium plated,, fancy type,60 cm long between flanges fixed with and including CP brass screws, rawl plug etccomplete all as specified and directed. |
| 73 | S&F in repair Toilet Cabinet PVC /ABS body of size 350x450mmx125mm of approved quality Make Commander/Prayag or equivalentmakes as approved by GE. |
| 74 | S&F in repair Chromium plated brass wall mixer 3-in-1 system fancy type with provision for both hand shower and overhead shower complete with wall Flange (without Hand & over head Shower) screwed down for 15 mm bore GI pipe complete all as specified and directed. |
| 75 | S&F in repair Chromium plated brass central hole Basin Mixer without Popup Waste system complete screwed down for 15 mm bore GI pipe complete all as specified and directed. |
| 76 | M&L taking out drapery rod and supply and fixing polyester coloured venetian blind mounted on doors windows with aluminium hanging channel with sliding wheel rope including all necessary fittings andfixture complete all as specified and directed |
| 77 | S&F in repair fancy type chromium plated health faucatwith1.50 metre longPVC tube coverCP flexible with wall hook suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified and directed. Make-Prayag or other equivalent makes as approved by GE. |
| 78 | S&F in repair drapery fancy type curtain rod shall be 32 mm dia of aluminium pipe with powder coating with wooden finish including bracket rings,fancy knob , curtai ring 08 Nos minimumincluding all fixing arrangement complete all as specified and directed. |
| 79 | S&F 40mm nominal bore of pipe for drain out pipe insunken floors galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc)complete all asspecified and directed. |
| 80 | S&F in repair 20 mm dia bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed. |
| 81 | S&F in repair 15mm size PVC connections internally threaded with PVC washer,PTMT nuts of length 450mm complete all as specified and directed. |
| 82 | S&F in repair PVC (SWR) pipes 150 mm,single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed |
| 83 | S&F in repair PVC (SWR) bends any radius for 150 mm bore of pipe complete all as specified and directed |
| 84 | S&F in repair PVC (SWR) pipes 110 mm bore, single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 85 | S&F in repair PVC (SWR) bends any radius, with access door, for 110 mm bore of pipe complete all as specified and directed. |
| 86 | S&F in repair PVC (SWR) pipes 75 mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 87 | S&F in repair PVC (SWR) bends any radius, with access door, for 75 mm bore of pipe complete all as specified and directed. |
| 88 | S&F in repair PVC (SWR) junction, with access door, single (single T) equal or unequal, for 110 mm bore of pipe complete all as specified and directed |
| 89 | S&F in repair PVC (SWR) junction, with access door, single (single T) equal or unequal, for 75 mm bore of pipe complete all as specified and directed |
| 90 | S&F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement, for 75 mm dia of outlet complete all as specified and directed |
| 91 | 15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete including taking up or down existing steel tubingpipe complete all as directed. |
| 92 | 20mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete including taking up or down existing steel tubingpipe complete all as directed. |
| 93 | M&L for Cutting chases, pinningin making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills sunshades, shelves lintels etc and cutting chases for concealed water pipes etc and making good cutting not exc 10cm.complete all as specified and directed. |
| 94 | S&F powder coated aluminium sliding window two track with two glass shutters fixing with 4.8 mm thick plain glass sheet aluminium powder coated section aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etccomplete fittings as approved. The Size of aluminium section shall beunder :-(i) Two track top and vertical - Jindal main-2010 section No 20829 or equivalent (ii) Two track bottom- Jindal main-2010 section No 20830 or equivalent (iii) Shutter vertical section- Jindal main- 2010 Section 20606 or equivalent (iv) Shutter top and bottom - Jindal Main-2010 Section 20604 or equivalent (v) Shuttervertical middle (interlock) -Jindal Main-2010 section 20605 or equivalent |
| 95 | S&F powder coated aluminium sliding window threetrack with two glass shutters fixing with 4.8 mm thick plain glass sheet, and one shutter with and including stainless steel wire gauge cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminium power coatet sections, aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etccomplete fittings as approved. Note Size of aluminium section shall beunder :-(i) Threetrack top and vertical - Jindal main-2010 section No 20829 or equivalent (ii)Three track bottom- Jindal main-2010 section No 20830 or equivalent (iii) Shutter vertical section- Jindal main- 2010 Section 20606 or equivalent (iv) Shutter top and bottom - Jindal Main-2010 Section 20604 or equivalent (v) Shuttervertical middle (interlock) -Jindal Main-2010 section 20605 or equivalent |
| 96 | S & F in repair Vitreous China urinals, half stall typewhite urinal, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed. |
| 97 | S&F door seal bottom, rubber shield, anti rust, brown colour black rubber including necessary screws etc., complete all as specified and directed. |
| 98 | S&F in repair aluminium die cast body door closer hydrau lically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed. |
| 99 | Preparing surfaces, holding the members in true position and welding in reparis n. exc 2.5 cm in length, thickness of metal to be welded exc 6 mm but n. exc9 mm complete all as directed. |
| 100 | S&FFramed work such as grills, gratings, etc.. with ends of barsshouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 101 | M&L for75mm thick PCC(Cement concrete) 1:3:6 typeC-2 using 40mm gradedstone aggregate as in plinth protection finished even and fair and making 50mm deep joints at every 3 metre interval and at every corner and filling the jointswith bitumen of grade 85/25 and sand mixture 1:3 complete all as specified and directed. |
| 102 | Resecuring or easing & adjusting without taking of steel window leaf n exc 1.00 sqm each leaf including cleaning of pivate, re-alignment of shutter and locking system after removing of side bent complete all as specified and directed. |
| 103 | Brick work with sub class \"B\" bricks (old size) straight or curved on plan exc 6.00m mean radius built in CM (1:6) including demolition of brick work/stone masonry built in cement mortar complete all as specified and directed. |
| 104 | Brick work with sub class ‘B’ bricks (old size), straight or curved on plan to any radius inhalf brick thick walls built in CM 1:4 including demolition of brick work/stone masonary built in cement mortarcomplete all as specified and directed. |
| 105 | Disconnecting & taking down existing water tank of capacity exc 250 litres and not exc. 500 litres and removing from site complete S&F rotational moulded polyethylene water storage tanks 500 litres capacity (cylindrical verticalwith closed top) hoistedwith and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part Icomplete all as specified and directed. |
