Haryana Police Housing Corporation Limited has published Construction Of Non Residential Building I.E 2 Barracks For Trainees Guest Houses , Ors Mess Electrical Substation, Water Supply, Re-Use Circulation, D.G Set And Transformer Etc. Irb Campus At Village Tundlaka Distt. Nuh. Submission Date for this Tender is 13-06-2022. Diesel Generators Tenders in Panchkula Haryana. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 03-Jun-2022 | Corrigendum_Date | Date | 13-06-2022 |
| Sl. No. | Item Description |
| 1 | HSR PART (CIVIL) |
| 2 | Clearing grass and removal of the rubbish up to a distance of 50m outside the periphery of the area cleared. HSR 4.2 |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. HSR 4.14.1 |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. (HSR 4.32) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded stone aggregate 40 mm nominal size) HSR 6.1.6 |
| 6 | DESIGN MIX CONCRETE |
| 7 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works up to plinth levelHSR 6.25.1(Note :- Cement content considered in this item is @ 330 kg/cum. Less cement used as per design mix is recoverable. However no extra payment shall be made if excess cement is used as per design mix). |
| 8 | All works above plinth level up to floor IV level HSR 6.25.2 |
| 9 | CENTRING AND SHUTTERING (FORM WORK |
| 10 | Columns, piers, abutments, pillars, posts and struts HSR 6.29.3 |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for (HSR6.30) 6.30.1) Foundations, footings, bases of columns, etc. for mass concrete |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. HSR 6.30.2 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for (Suspended floors, roofs, landings, balconies) HSR 6.30.3 |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) HSR 6.30.4 |
| 15 | Centering and shuttering including strutting, propping etc. (Lintels, beams, plinth beams, girders, bressumers sqm and cantilevers) HSR 6.30.5 |
| 16 | Columns, Pillars, Piers, Abutments, Posts and Struts. HSR 6.30.6 |
| 17 | Centering and shuttering including strutting, propping etc.(Stairs, (excluding landings) except spiral-staircases ) HSR 6.30.7 |
| 18 | Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, ending, placing in position, binding, astage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth leve Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more. HSR 6.34.6 |
| 19 | B. BRICK WORK |
| 20 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement: 4 coarse sand) HSR 7.20.1 |
| 21 | HALF BRICK MASONRY |
| 22 | Half brick masonry with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level. HSR7.28.2 cement mortar 1:4 (1 cement: 4 coarse sand) |
| 23 | Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. bars at every third course of half brick masonry. HSR 7.30 |
| 24 | Providing and laying autoclaved aerated cement blocks masonrywith 100 mm thick AAC blocks in super structure above plinth level up to floor IV level in cement mortar 1 :4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos. 6 mm dia M.S. bars at every third course of masonry work (HSR 7.50) |
| 25 | Providing and laying autoclaved aerated cement blocks masonrywith 150mrn/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor IV level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in- Charge. (The payment of RCC band and reinforcement shall be made for separately). (HSR 7.51) |
| 26 | Dressed or moulded three brick cornice laid in cement sand mortar 1 :4 including 12 mm thick cement plaster 1 :4 or pointing, as required HSR7.57 |
| 27 | Stone work (machine cut edges) for wall lining etc. (veneer work) up to 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1 :3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately)Red sand stone - exposed face fine dressed with rough backing.HSR 8.9.1.5 (30 mm thick) |
| 28 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1 :2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. HSR 8.10 |
| 29 | Providing & fixing factory manufactured jali of reinforced cement concrete consisting of cement , coarse sand and 10mm & down gauge bajri in ratio of 1: 1 :2 with Bmm dia tor steel. Outer frame of the jail will be 50mm wide & 25mm thick & inner frame of jali will be 25mm wide and 25mm thick with smooth finish as per design approved by the Engineer-in-Charge including fixing in position up to any height with cement sand mortar 1 :4 complete in all respect (HSR 8.17) |
| 30 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfonns, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. (HSR 8.26) 8.26.2) Granite of any colour and shade 8.26.2.2) Area of slab over 0.50 sqm |
| 31 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge (HSR 8.27) 8.27.2) Granite work |
| 32 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platfonn, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (HSR 8.28) |
| 33 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.HSR 8.29 |
| 34 | Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : (HSR 9.17) 9.17.1) In 75x75 mm deep chase |
| 35 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (HSR 9.18) |
| 36 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of oaintina with 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3): 1996 (Boards with BIS certification marks) (HSR 9.46.2) |
| 37 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a ompletely sealed unit HSR 9.47.3 |
| 38 | RAIN WATER SPOUTS AND PIPES Supplying and fixing in position 60 cm long G.I. pipe class "B" spouts in chajjas and cantilevers.50 mm internal dia HSR 9.55.5 |
| 39 | Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameterHSR 9.57.1 |
| 40 | HSR 9.57.1 (75 mm dia) |
| 41 | HSR 9.57.2 (110 mm diameter) |
| 42 | HSR 9.57.3(150 mm diameter) |
| 43 | Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. HSR 9.58.1 Coupler |
| 44 | Coupler |
| 45 | HSR 9.58.1.1 (75 mm) |
| 46 | HSR 9.58.1.2 (110 mm) |
| 47 | HSR 9.58.1.3 (150 mm) |
| 48 | Single tee with door |
| 49 | HSR 9.58.3.1 (75x75x75 mm) |
| 50 | HSR 9.58.4.2 (110x110x110 mm) |
| 51 | Bend 87.5° |
| 52 | HSR 9.58.5.1 (75 mm bend) |
| 53 | HSR 9.58.5.2 (110 mm bend) |
| 54 | HSR 9.58.5.3 (150 mm bend) |
| 55 | Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. :100 mm diameter HSR 9.62.1 |
| 56 | 100 mm dia |
| 57 | 150 mm diameter |
| 58 | Providing and laying of screed of 50 mm thick cement concrete 1 :8:16 to be laid below the topping. HSR 10.4 |
| 59 | Providing and laying cement plaster skirting up to 30 cm height, with cement mortar 1 :3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. HSR 10.13.1 (18 mm thick ) |
| 60 | Extra for using hardener at top surface (3.5Kg /sqm) of trimix M25 to finish surface complete in all respect .HSR 10.15 |
| 61 | Providing and laying of chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand).Light shade pigment using white cement HSR 10.30.1 |
| 62 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown,Cat Eye or equivalent. HSR 10.50.1 |
| 63 | Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : (HSR 10.37) 10.37.1) 25 mm thick |
| 64 | Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (HSR 10.38) |
| 65 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.HSR 10.61 |
| 66 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. . (HSR10.62) |
| 67 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete (HSR 10.63) 10.63.2) Size of Tile 600x600 mm |
| 68 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (HSR 10.67) 10.67.2) Size of Tile 600x600 mm |
| 69 | Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. (HSR 10.70) (DERIVED) 10.70.2) Size of Tile 600x600 mm |
| 70 | Providing and fixing of chicken wire mesh for avoiding cracks in plaster with necessary nail/screws etc. complete in all respect to the entire satisfaction of engineer-in-charge. HSR 11.17 |
| 71 | Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ per1ite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete (HSR 11.46) |
| 72 | Polymer plasterProviding, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2 ).12 mm average thickness. DSR 26.32.1 (2018) D/d 30% |
| 73 | Corbelling around almirah including 12mm thick cement plaster 1 :6HSR 11.55 |
| 74 | Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR 11.58) |
| 75 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: (HSR 11.64) 11.64.1) New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 76 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: (HSR 11.67) 11.67.1) Water thinnable cement primer |
| 77 | Applying priming coat: (HSR 11.68) 11.68.3) With ready mixed red oxide zinc chromate primer of approvedbrand and manufacture on steel galvanised iron/ steel works |
| 78 | Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade (HSR 11.71) 11.71.1) Two or more coats on new work |
| 79 | Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR /11.76) |
| 80 | Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. (HSR11.77) |
| 81 | Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 11.78) |
| 82 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete.HSR 12.3.1.1 (50x12mm) |
| 83 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately)18 mm thick . HSR 12.27.1 |
| 84 | Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (HSR 12.37) 12.37.1) 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws |
| 85 | 12.37.3) 25 mm thick (for cupboard) including ISi marked nickel plated bright finished M.S. piano hinges with necessary screws. HSR 12.37.3 |
| 86 | Cupboard 25mm flush door |
| 87 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding HSR 12.50.1 |
| 88 | Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type HSR 12.87.1 |
| 89 | Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : HSR 12.98.1 (300x16 mm) |
| 90 | 12.98.2) 250x16 mm Slinding Bolt |
| 91 | Providing and fixing aluminium tower bolts, ISi marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868 ) transparent or dyed torequired colour or shade, with necessary screws etc. complete (Powder coated) Note:- Nothing will be paid extra for powder coating (HSR 12.99.1) 3000x10 mm |
| 92 | (HSR 12.99.2) 250x10 mm |
| 93 | HSR 12.99.3 200x10 mm |
| 94 | 12.99.4) 150x10 mm Tower Bolt |
| 95 | 12.99.5 100x10 mm |
| 96 | Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete (Powder coated) Note:- Nothing will be paid extra for powder coating (HSR 12.102) 12.102.1) 125 mm |
| 97 | 12.102.2) 100mm Handles |
| 98 | Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (Powder coated) Note:- Nothing will be paid extra for powder coating (HSR 12.103) 12.103.2) Twin rubber stopper |
| 99 | Providing and fixing of roller blinds on windows complete with material andlabour complete with push up & down arrangement as per approved design / colour and Engineer-in-charge. HSR 12.114 |
| 100 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : (HSR 12.157) 12.157.1.2) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 101 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.HSR 12.157.2.2 |
| 102 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides HSR 12.158.2 |
| 103 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.0 mm thickness (weight not less than 10kg/sqm)HSR12.159.2 |
| 104 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With brass cover plate minimum 1.25 mm thickness.HSR 12.160.2 |
| 105 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.710 X 19 mm HSR12.162.5 |
| 106 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long.HSR12.163.2 |
| 107 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). HSR 12.171 |
| 108 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 2.0 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:. (HSR 13.3) 13.3.2) Profile C (125x60mm) 13.3.2.2) Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) Single Rebet |
| 109 | Profile E (160x60mm) Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)HSR 13.3.3.2 |
| 110 | Double Rebet |
| 111 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M .S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides (HSR 13.9.2) |
| 112 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with (HSR13.10.1) 4.0 mm thick glass panes |
| 113 | Providing & fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of Gasket I beading shall be paid as per respective item) (HSR 13.24.1) Float glass panes of 5.5mm thickness |
| 114 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes HSR 13.30.1 |
| 115 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. topcover of required thickness for rolling shutters. 80x1 .20 mm M.S. laths with 1.20 mm thick top cover. HSR 13.37.2 |
| 116 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per pproval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). HSR 13.41 |
| 117 | Road & Parking |
| 118 | Compaction of Earth work Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers)(HSR 17.5.3) |
| 119 | Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect.HSR17.69.2 |
| 120 | Construction of unreinforced plain cement concrete pavement in M-25 mix design over aprepared sub base with OPC 43 grade conforming to IS:383 mixed with concrete mixer using batch type concrete mixer as per IS:1791, laid in position, compacted with needle vibrator, screed vibrator and plate vibrator, dewatering of free water with vaccum pump, finishing the surface with power floater, finishing to required lines and grades as per drawings and technical clause 1501 of MORTH specifications (HSR 17.73) |
| 121 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement sluny mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/ sqm This layer will be allowed to air cure for 4 hours. (b) Second layer of sluny of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.HSR 28.15 |
| 122 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm(b) laying second layer of Fibre glass cloth when the first layer is still green. verlaps of joints of fibre cloth should not be less than 10cm.(c) third layer of 1.5 mm thickness consisting of sluny of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately). For the purpose of measurement the entire treated surface will be measured. (HSR 28.16) |
| 123 | Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1: 1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manne HSR 28.43 |
| 124 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to MMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.HSR 29.1 |
| 125 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: HSR 29.6 |
| 126 | (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part Ill (the system must passed the proof test at 1.5 times design wind pressure without any failure),including functional design of the aluminium sections for fixing glazing panelsof various thicknesses, aluminium cleats, sleeves and splice plates etc.gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weathersilicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwavecured EPDM gaskets for water tightness, pressure equalisation & drainageand protection against fire hazard including: |
| 127 | (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. |
| 128 | (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shopenvironment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. |
| 129 | (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. |
| 130 | (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in?harge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge |
| 131 | Notes for Item 29.6: 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm up to two decimal places.2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. 3. Competent authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work.- - - ·- - - . . - - . - 3.1. Performance Laboratory Test for Air Leakage Test (-50pa to· 300pa)& (+50pa to +300pa) as per ASTM E-283-04 testing method for a rangeof testing limit 1 to 200 mVhr 3.2. Static Water Penetration Test (50pa to 1500pa) as per ASTME· 331· 09 testing method for a range up to 2000 ml. 3.3 Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01· 05 testing method for a range up to 2000 ml 3.4 Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range up to 50 mm 3.5 Seismic Movement Test (up to 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 3.6 Onsite Test for Water Leakage for a pressure range 50 kpa to 240kpa (35psi) up to 2000 m |
| 132 | HSR Civil Amount |
| 133 | Tubewell items |
| 134 | Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe for tube well including cleaning and priming the tube well.HSR 33.3 |
| 135 | Supplying, assembling, lowering and fixing in vertical position in bore well, Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia HSR 33.8.2 |
| 136 | Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia HSR 33.9.2 |
| 137 | Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. HSR 33.15 |
| 138 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of:150 mm dia HSR 33.16.2 |
| 139 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp HSR33.17.2 |
| 140 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I).HSR 33.18.2 |
| 141 | Development of tube well in accordance with IS : 2800 (part I)and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V"" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. HSR 33.19 |
| 142 | Tubewell Amount |
| 143 | NS Items |
| 144 | Earth Filling with the earth brought from outside the campus irrespective of any lead, including laying in 15cm layers, watering, compacting and consolidating complete in all respect & to the full satisfaction of engineer in charge |
| 145 | Providing 50mm x 4mm size groove as expansion joint in concrete pavement by mechanical cutter, complete in all respect.NS |
| 146 | P/F hanging rod i/c the cost of wall to wall clamp and screws complete.NS |
| 147 | Finishing Heat Resistant tiles by grinding mechanically of roof terrace and disposal of wastage complete in all respect. |
| 148 | Curtain Rod 25 mm of S.S. with 304 grade all Material Wall to wall Latoo complete in all respect.NS |
| 149 | Making corbelling with CC 1:1.1/2:3 with stone aggregate 20mm thick nominal size i/c shuttering.NS |
| 150 | Extra labour for plaster for any type of corbelling inRCC at top of parapet complete in all respect.NS |
| 151 | Extra for making hole in working slab for gas pipe/ stair railing etc. including finishing complete.NS |
| 152 | P/F zinc coated clamp 90mm and 110mm dia i/c cost of 12mm screw G.I. rod adjustable and fastner in RCC roof etc. complete in all respect.NS |
| 153 | Providing & fixing 8mm thick M.S. Rod fully threaded with nut bolt and washers in aluminium section window door shutters complete in all respects.NS |
| 154 | Providing and fixing 25 mm thick finished red sand stone both side slightly rounded for partition and shelves in Cupboard.NS |
| 155 | Providing and Fixing mumty door consisting of mild steel angle iron frame 35x25x5mm thick, cross braces 20x5mm @4nos. at each side) and 2 nos. MS flat 50x6mm and covered withMS sheet 16 gauge including locking arrangement (with sliding bolts & T-bolt). (NS item) |
| 156 | P/F 4mm thick acrylic sheet on toilet flush door etc. complete in all respect. (NS item) |
| 157 | P/F door closer 1938( Hydraulic door closer) complete in all respect GODREJ MAKE |
| 158 | Providing & fixingstainless steel jali 22G & 304 Grade in aluminium wire gauze shutter of window and door etc. complete in respect.NS |
| 159 | Providing & fixing wooden flooring 8mm thick victor make with 1mm thick foam Complete in all respect .NS |
| 160 | Pdg and Fixing wall paperNS |
| 161 | Pdg. And Fixing 4mm thick venior with PU polish complete in all respect.NS |
| 162 | Pdg and Fixing Unistone TilesNS |
| 163 | Providing and fixing of external wall cladding with 6mm thick (HPL) fundermax brand or equivalent over aluminium anodised section framing of branded make use wind brackets LT section as per requirment of manufactor of apporove make complete in all respect.NS |
| 164 | Providing & Fixing aluminium fittings for door and windows shutters with stainless steel or C.P brass screws of required size complete.Folding Handle 100mm |
| 165 | Providing & Fixing aluminium fittings for door and windows shutters with stainless steel or C.P brass screws of required size complete.I Hock |
| 166 | Extra for Granite polish on Kota stone flooring |
| 167 | Providing and fixing cement concrete (machine made) grade M25 kerb stone of size 300x300x150mm planning and fixing 100 position complete with 1:3 cement mortar for jointing at ground level. NS |
| 168 | Total NS Amount |
| 169 | HSR P.H Items |
| 170 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: HSR 4.16 |
| 171 | Pipes, cables etc. exceeding 300 mm metre dia but not exceeding 600 mm HSR 4.16.1.3 |
| 172 | Extra for excavating trenches for pipes, cables etc. in all kinds of metre soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre). HSR 4.17 |
| 173 | Extra for excavating trenches for pipes, cables, etc, in all kinds of metre soil for depth exceeding 3 m in depth, but not exceeding 4.5 m.(Rate is over corresponding basic item for depth up to 1.5 metre.) HSR 4.18 |
| 174 | 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size)HSR 6.1.2 |
| 175 | 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) HSR 6.1.6 |
| 176 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of ppropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1 :2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.HSR 8.30.2 |
| 177 | Neat cement punning. HSR 11.3 |
| 178 | 12 mm cement plaster of mix(HSR 11.5.3) 1 :4 (1 cement: 4 fine sand) |
| 179 | Drilling and tapping cast iron pipe lines of all diameters and screwing in ferrule and connections - (HSR 20.24.1) Ferrule size 10 mm |
| 180 | Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. (HSR20.26.2) 22.86 cm thick wall |
| 181 | 11.43 cm thick wall |
| 182 | Cutting holes up to 23 cm square for pipes in flooring and roofs of brick tiles with lime concrete and making good including, repointing, replastering and colour or white washing where required.HSR 20.27.2 |
| 183 | Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per 1.5.1. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. |
| 184 | Size 600 mm X900 mm inside (with 455 mm x 455 mm coverand frame light duty single seal weighing 20 kg with R.C.C.slab)HSR 21.84.3 |
| 185 | Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS: 12592 including setting the same to correct lines and levels in 1 :3 cement sand mortar over manhole including carriage loading unloading stacking handling re-handling etc. complete in allespects to the satisfaction to the Engineer-in-charge. (HSR 21.93.2) Type:- Extra Heavy Duty Set (EHD-20) 560MM Clear Opening |
| 186 | Making holes for HCL soil / Waste pipe by core cutting up to 200 mm thick slabs and sealing with Drip seal sealant complete in all respect. (HSR 2021 /21.100) 21.100.2) |
| 187 | 100 mm dia pipe |
| 188 | 175mm dia pipe |
| 189 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.HSR 22.2.1 |
| 190 | Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge).Two way HSR 22.8.2 |
| 191 | Providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.HSR 22.5 |
| 192 | Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 225 mm HSR 22.10.1.2 |
| 193 | Providing and fixing draining board with C.I. brackets including painting of brackets, cutting and making good the walls wherever required White glazed fire clay draining board of size 600x450x 25 mm.HSR 22.11.1 |
| 194 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. HSR 22.15 |
| 195 | Providing and fixing 40mm i/d G.I. waste pipe embedded in walls up to floor level including cost of union and plumber joint.HSR 22.16 |
| 196 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (HSR2021/22.22)22.22.1) White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 197 | Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass)with waste fitting as per IS : 2556, C.I. trap with outlet grating and othercouplings in C.P. brass, including painting of fittings and cutting and aking good the walls and floors wherever required.Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern.HSR 22.26.5 |
| 198 | Providing and fixing one piece construction white vitreous chinaware squatting plate with an integral longitudinal flushing pipe, white P.V.C. flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required.Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern HSR22.27.5 |
| 199 | Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.HSR22.33 |
| 200 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan (HSR 22.35) |
| 201 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make asapproved by Engineer - in - charge. (HSR22.38) |
| 202 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. HSR 22.39.1 |
| 203 | Providing and fixing toilet paper holder: HSR 22.42.1C.P. brass |
| 204 | Providing & fixing white vitreous chinaware water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.HSR 22.45 |
| 205 | Providing and fixing white vitreous chinaware battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. HSR 22.46 |
| 206 | Providing and fixing white vitreous chinaware flat back or wall comer type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.HSR 22.47 |
| 207 | Providing and fixing white vitreous chinaware squatting plate urinal with integral rim longitudinal flush pipe. HSR 22.48 |
| 208 | Providing and fixing in position best Indian make vitreous chinaware channel of size 600mmx150mm including laying and fixing in cement concrete 1 :2:4 complete as required by the Engineer-in-charge.HSR 22.49.2 Single Colour |
| 209 | Providing and fixing partitions for different type of urinals. Vitreous Chinaware Partition plate. Small size 680mm x 330 mm HSR 22.50.1.1.1) White |
| 210 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1 :3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1 :4 (1 cement : 4 coarse sand) : (HSR 22.81.2)75 mm dia |
| 211 | Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay non-modular bricks HSR 22.82.1 |
| 212 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1 :2:4 (1 cement : 2 oarse sand : 4 graded stone aggregate 20 mm nominal size), ncluding finishing complete so as to make it leak proof. HSR 22.83 |
| 213 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brassthreaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step CPVC solvent cement andthe cost of cutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.HSR 22.86. |
| 214 | Concealed work, including cutting chases and making good the walls etc. |
| 215 | 20 mm nominal outer dia Pipes |
| 216 | 25 mm nominal outer dia Pipes |
| 217 | 32 mm nominal outer dia Pipes |
| 218 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia PipesHSR 22.87.2 |
| 219 | 20 mm nominal outer dia Pipes |
| 220 | 25 mm nominal outer dia Pipes |
| 221 | 32 mm nominal outer dia Pipes |
| 222 | 40 mm nominal outer dia Pipes |
| 223 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) (HSR 22.94.3) |
| 224 | 25 mm dia nominal bore |
| 225 | 32 mm dia nominal bore |
| 226 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): (HSR 22.98) |
| 227 | 25 mm nominal bore |
| 228 | 32 mm nominal bore |
| 229 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter HSR 22.102.2 |
| 230 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (HSR 22.103.2) 20 mm nominal bore |
| 231 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931HSR 22.104.1 |
| 232 | 15 mm nominal bore |
| 233 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bor HSR22.106.1 |
| 234 | 15 mm nominal bor |
| 235 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.HSR 22.107 |
| 236 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 .HSR 22.108 |
| 237 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. (HSR2021/ 22.109) |
| 238 | Providing and fixing PTMT pillar cock of approved quality and colour . 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms HSR 22.113.2 |
| 239 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (HSR 22.127) |
| 240 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1: 1 (1 cement : 1 fine sand) including testing of joints etc. complete: (HSR 22.163 |
| 241 | For 200mm Dia. Pipe |
| 242 | 300mm i/d |
| 243 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P typeWith common burnt clay non-modular bricks of class designation 7 .5 (HSR 22.166.1.1) |
| 244 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. HSR 22.181 |
| 245 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (ofapproved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.HSR 22.209 |
| 246 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. (HSR 22.222) |
| 247 | 110mm dia pipe |
| 248 | 90mm dia pipe |
| 249 | P.H Amount |
| 250 | PH (NS PART) |
| 251 | Pdg.and fixing in position 5mm thick looking mirror bevelled on sides fixing in position with necessaryC.P. screws and washercomplete.NS |
| 252 | P/F Counter wash basin oval shape under counter wash basin . Complete in all respect.NS |
| 253 | Providing and fixing CPVC ball valve/ gate valve (union type) with of approved quality complete in all respect |
| 254 | 25mm dia |
| 255 | 32mm dia |
| 256 | 40mm dia |
| 257 | Providing and fixing SWR PVC pipe classic type"B" and specials ISI marked i/c fitting joint solvent mixture comlete in all respect.NS |
| 258 | Special for 90 mm dia pipe |
| 259 | i) Pipe Clip/ Clamp |
| 260 | ii) Coupler/ Socket |
| 261 | iii) Bend with Door |
| 262 | iv) Single T |
| 263 | v) Vent Cowel with Jali |
| 264 | Special for 110 mm dia pipe |
| 265 | i) Coupler/ Socket |
| 266 | ii)SingleBend |
| 267 | iii) Single T |
| 268 | iv) P-Trap (DS) 110x110mm |
| 269 | v) Nanhi Trap with Jali (110x110mm) |
| 270 | Gully Trap |
| 271 | Clamp |
| 272 | Single junction with door /Y Tee |
| 273 | Providing and fixing C.P. jali with frame complete in all respect |
| 274 | Providing and fixing CP Brass flange complete |
| 275 | Providing and fixing in position best quality stainless steel sink (Glossy) with complete fitting (Jayna make) Size 45” x 20” with 2 nos. bowls of size 20” x 16”,8” |
| 276 | Pdg and fixing Zinc coated clamps complete in all respect. |
| 277 | P/F in position Towel Ring of Jaquare make cat no 1173 complete in all respect.(as approved by the Engineer-in- charge). |
| 278 | P/F in position C.P Towel Rack of Jaquare make cat no 1181 N complete in all respect.(as approved by the Engineer-in- charge). |
| 279 | P/F in position C.P brass wash basin mixture of Jaquare make cat no 29011 complete in all respect.(as approved by the Engineer-in- charge). |
| 280 | P/F in position C.P brass health faucetof Jaquare make cat no 573 complete in all respect.(as approved by the Engineer-in- charge). |
| 281 | P.HN.S Amount |
| 282 | Estate Services |
| 283 | CIVIL WORK |
| 284 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, includinggetting out the excavated soil and disposal of surplus excavated soil as directed, with a lead of 50 m. HSR 4.14 |
| 285 | All kinds of soil HSR 4.14.1 |
| 286 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. HSR 4.16 |
| 287 | All kinds of soil |
| 288 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.HSR 4.16.1.2 |
| 289 | Extra for excavating trenches for pipes, cables etc. in all kinds ofsoil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre). HSR 4.17 |
| 290 | Extra for excavating trenches for pipes, cables, etc, in all kinds of soil for depth exceeding 3 m in depth, but not exceeding 4.5 m. (Rate is over corresponding basic item for depth up to 1.5 metre.) HSR 4.18 |
| 291 | Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered). HSR 4.22 |
| 292 | Depth exceeding 3 m but not exceeding 4.50 m HSR 4.22.3 |
| 293 | Filling available excavated earth (excluding rock) in trenches, cum plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. HSR 4.32 |
| 294 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level HSR 6.1 |
| 295 | 1:4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded stone aggregate 40 mm nominal size) HSR 6.1.6 |
| 296 | Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) HSR 6.8 |
| 297 | 40mm thick HSR 6.8.2 |
| 298 | Providing & applying a coat of residual petroleum bitumen of sqm grade of VG-1 O of approved quality using 1. 7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.HSR 6.10 |
| 299 | 1 : 1. 5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3graded stone aggregate 20 mm nominal size) HSR 6.14.1 |
| 300 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement.HSR 6.15 |
| 301 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size) HSR 6.15.1 |
| 302 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). HSR 6.16 |
| 303 | Centering and shuttering including strutting, propping etc. and removal of form for (HSR6.30) 6.30.1) Foundations, footings, bases of columns, etc. for mass concrete |
| 304 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. HSR 6.30.2 |
| 305 | Centering and shuttering including strutting, propping etc. and removal of form for (Suspended floors, roofs, landings, balconies) HSR 6.30.3 |
| 306 | Centering and shuttering including strutting, propping etc. (Lintels, beams, plinth beams, girders, bressumers sqm and cantilevers) HSR 6.30.5 |
| 307 | Columns, Pillars, Piers, Abutments, Posts and Struts. HSR 6.30.6 |
| 308 | Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level HSR 6.34 |
| 309 | Hot rolled deformed bars HSR 6.34.4 |
| 310 | Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in. HSR 7.21 |
| 311 | Cement mortar 1:4 (1 cement: 4 coarse sand).HSR 7.21.1 |
| 312 | Brick work with modular calcium silicate bricks machine moulded conforming to IS:4139, class designation 10 average compressive strength in super structure above plinth level up to floor IV level in : HSR 7.45 |
| 313 | Cement mortar 1:4 (1 cement: 4 coarse sand) HSR 7.45.1 |
| 314 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.HSR 9.18 |
| 315 | Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter HSR 9.57.2 |
| 316 | Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionBend 87.5°(110 mm bend) HSR 9.58.5.2 |
| 317 | Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. HSR 10.1 |
| 318 | Providing and laying of conglomerate floor 40mm thick cement concrete topping 1 :2:4.HSR 10.8 |
| 319 | Providing and fixing glass strips in joints of terrazzo/ cement concrete floors.HSR 10.22 |
| 320 | 40 mm wide and 4 mm thick.HSR 10.22.1 |
| 321 | FLAT BRICK OR TILE FLOORING |
| 322 | Providing and laying of flat brick or tile flooring with bricks of class designation 7 .5 laid in cement sand mortar 1 :4 on 100 mm thick cement concrete 1:8:16 and 100 mm sand filling and cement pointing 1 :2 on top.HSR 10.35.1 |
| 323 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete (HSR 10.63) 10.63.2) Size of Tile 600x600 mm |
| 324 | 10 mm thick cement plaster.HSR 11.4 |
| 325 | 1 :3 (1 cement: 3 fine sand) HSR 11.4.2 |
| 326 | 12 mm cement plaster of mix.HSR 11.5 |
| 327 | 15 mm cement plaster on the rough side of single or half brick wall of mix.HSR 11.6 |
| 328 | 1 :4 (1 cement: 4 fine sand) HSR 11.6.1 |
| 329 | 1:4 (1 cement: 4 coarsesand) HSR 11.8.1 |
| 330 | 15 mm cement plaster on rough side of single or half brick wall of mix: HSR 11.9.1 |
| 331 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: (HSR 11.64) 11.64.1) New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 332 | Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc.HSR 11.77 |
| 333 | Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.HSR 11.78 |
| 334 | Finishing walls with Acrylic Smooth exterior paint of required shade.HSR 11.95 |
| 335 | New work (Two or more coat applied @ 1.67 litre/1 O sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)HSR 11.95.1 |
| 336 | Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (HSR 12.37) 12.37.1) 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws |
| 337 | Providing and fixing ISi marked oxidised M.S. sliding door bolts with nuts and screws etc. complete.HSR 12.65.1 |
| 338 | 300 x 16 mm |
| 339 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 2.0 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:. (HSR 13.3) 13.3.2) Profile C (125x60mm) 13.3.2.2) Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) Single Rebet |
| 340 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. HSR 13.29.2 |
| 341 | Providing & fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of Gasket I beading shall be paid as per respective item)HSR 13.24 |
| 342 | Float glass panes of 5.5mm thickness 13.24.1 |
| 343 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.HSR 13.27 |
| 344 | Laying of recycled Bituminous Pavement with Central Recycling Plant upto 75mm HSR 17.43 |
| 345 | Providing & laying 50 mm - 75 mm DBM using the reclaimed material to the extent of 30% per cent of the required quantity after carrying out necessary check and evaluation, adding fresh mateerial including rejuvenation as required, grade, level and thickness, all as specified in clause No.519. (5th revision) 2013 using bitumen VG-30 (minimum Bitumen content 4.50% i/c bitumen of retrieved material as per job mix formula) using 100-120 TPH batch type hot mix plant with appropriate arrangement for use of R.A.P, appropriate roller and with hydraulic paver finisher with sensor control to the required grade. The milled material to be used in DBM shall be minimum 80% of the theoretical quantity. Note:- If bitumen required is more than 4.50% as per job mix formula, no extra payment will be paid. Extra bitumen required will be considered as incidental to work. HSR 17.43.1 |
| 346 | Dismantling of existing damaged Bitumen surface by cold Milling Machine up to 50 mm depth and hauling the milled material up to 10 km and stacking at nearest recycling Plant site. HSR 17.43.2 |
| 347 | Making flanged joints for cast iron pipe, valves or specials HSR 20.5 |
| 348 | 100mm i/d HSR 20.5.2 |
| 349 | 150mm i/d HSR 20.5.4 |
| 350 | Providing & fixing cast iron double flanged swing check type reflux (non return) valve PN-1.6 marked with IS: 5312 including nuts & bolts marked with IS: 1363, rubber sheet marked with IS: 638 etc., carriage loading, unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-Charge HSR 20.11 |
| 351 | 100mm i/d HSR 20.11.2 |
| 352 | 150mm i/d HSR 20.11.3 |
| 353 | Providing, lowering, laying in trenches, aligning, fixing in position and jointing Ductile Iron (DI) ISI marked K-7 grade S&S pipes as per IS: 8329-2000 (amended up to date), with internal cement mortar lining for potable water with rubber ring (EPDM/SBR) joints as per IS: 5382-1985 (excluding special accessories) complete including all material, labour, hydraulic testing and commissioning as per technial specifications and as per direction of Engineer-in-charge. HSR 20.64 |
| 354 | 100mm i/dHSR 20.64.1 |
| 355 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:HSR 22.1 |
| 356 | White vitreous chinaware Wash basin size 630x450 mm with a pair of 15 mm C. P. brass pillar taps.HSR 22.1.1 |
| 357 | Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge.HSR 21.28 |
| 358 | Erection of R.C.C. ventilating column having minimum 200 mm internal dia and a height of 11 meters above ground level, including caps, cowls or wire domes etc. complete including carriage from the stores of the engineer-in-charge of works to site of works, loading, unloading, fixing and setting the same in position and embedding in foundation block (to be paid separately) complete. HSR 21.31 |
| 359 | Providing masonry plugs to ends of sewers of all types with 11.43 cm thick brick wall in cement sand mortar 1 :7 with 12 mm thick cement plaster 1: 6 (as required by the engineer-in-charge). HSR 21.57 |
| 360 | For circular sewers having internal diameter:- HSR 21.57.1 |
| 361 | 200 mm HSR 21.57.1.4 |
| 362 | 250 mmHSR 21.57.1.6 |
| 363 | 350 mm HSR 21.57.1.8 |
| 364 | 400 mm HSR 21.57.1.10 |
| 365 | Constructing brick masonry road gully chambers as per standard drawings (as per sizes given below) including dressing of beds and sides of chambers to exact profiles, 15cm thick lime concrete 16:24:100 (as per specified in item No.10.6) in foundations 1st class brick work laid in cement sand mortar 1 :5, 40 mm thick cement concrete 1 :2:4 topping inside the chamber with a floating coat of 1.5mm thick neat cement laid in one operation to the topping, the entire inner surface of the chamber rendered with neat cement not less than 12mm in thickness of 1 :2 cement sand plaster and finished with floating coat of neat cement 1 mm thick left absolutely smooth polished and correct to templates including labour for fixing the C.I. road gully grating and frame including painting with coal tar (as Specified in item No. Item 21.48) complete to the requirement of the Engineer in-charge HSR 21.87 |
| 366 | Single road gully chamber HSR 21.87.1 |
| 367 | Size: 610mm x 457mm x 800mm HSR 21.87.1.1 |
| 368 | Construction of circular standard brick-masonry manhole chambers to standard drawings on S.W. pipe sewers or other circular sewers up to the required depth in 1 :5 cement sand mortar lime concrete in bed and sides of pipe-sewer and cement concrete 1 :2:4 in benching 12 mm thick water tight 1 :2 cement sand plaster with a floating coat of neat cement and finished with two coats of sodium silicate of interior surface where required fixing cover and frame weight not less than 2:5 quintal painted with 3 coats of black bitumen paint fixing galvanised malleable iron steps embedded in 1 :2 cement sand mortar complete. The rate covers the cost of carriage of C.I. manhole, frame and cover and malleable iron steps from the stores of the engineer-in-charge of the works to site of works. the rate also includes the cost of accurately planed and fitted centring supports for all works as well as for all curves and special works cleaning out their beds etc. Sodium silicate will be supplied free of cost at the stores of the Engineer-in-charge HSR 21.91 |
| 369 | 200 mm internal diameter pipe sewer HSR 21.91.2 |
| 370 | For 1.80 meter depth below ground level |
| 371 | Extra over and above on item no. 21.91 for every additional per 0.30 metre depth of manhole up to 4 metres depth beyond 1.80 metres below ground level. |
| 372 | 200 mm internal diameter pipe sewer |
| 373 | For 2.10 meter depth below ground level |
| 374 | 250 mm internal diameter pipe sewer |
| 375 | For 2.40 meter depth below ground level |
| 376 | For 3.30 meter depth below ground level |
| 377 | For 3.60 meter depth below ground level |
| 378 | 350 mm internal diameter pipe sewer |
| 379 | For 1.80 meter depth below ground level HSR 21.91.6 |
| 380 | Extra over and above on item no. 21.91 for every additional per 0.30 metre depth of manhole up to 4 metres depth beyond 1.80 metres below ground level. HSR 21.92 |
| 381 | 350 mm internal diameter pipe sewer |
| 382 | For 2.10 meter depth below ground level |
| 383 | For 2.40 meter depth below ground level |
| 384 | 400 mm internal diameter pipe sewer |
| 385 | For 3.00 meter depth below ground level |
| 386 | For 3.30 meter depth below ground level |
| 387 | Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS: 12592 including setting the same to correct lines and levels in 1 :3 cement sand mortar over manhole including carriage loading unloading stacking handling re-handling etc. complete in all respects to the satisfaction to the Engineer-in-charge. HSR 21.93 |
| 388 | Extra heavy duty set (EHD 35) 560mm clear opening. HSR 21.93.1 |
| 389 | Providing salt glazed stone ware pipes grade "A" in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. HSR 21.94 |
| 390 | 200 mm HSR 21.94.3 |
| 391 | 250 mm HSR 21.94.4 |
| 392 | Providing lowering cutting jointing and testing RCC pipe class NP3 as per IS 458-2003 with spigot & socketed joints manufactured with ISI marked sulphateresitance cement as per ISI 12330 with rubber rings ISI marked antiternmite as required at site in to trenches for all depths and laying out the same to correct alignment gradients and levels including dressing and trimming and cutting of concrete beds and side of trenches, if required jointing with rubber rings in trenches and jointing with 1:3/2 cement sand mortar and with end dowels filled with 1:3/2 cement sand mortar and finishing the joints at an angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in item no. 21.38, item 21.44, item 21.45 & item 21.46 including cartage loading and unloading complete in all respects the internal diametric of the sewer being: HSR 21.95 |
| 393 | 350mm i/dHSR 21.95.1 |
| 394 | 400mm i/d HSR 21.95.2 |
| 395 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required.HSR 22.2 |
| 396 | White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.HSR 22.2.1 |
| 397 | Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 225 mm HSR 22.10.1.2 |
| 398 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (HSR2021/22.22)22.22.1) White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 399 | WASH BASINS, KITCHEN SINKS AND HARDWARES |
| 400 | Providing and fixing soil, waste and vent pipes HSr 22.51 |
| 401 | 100 mm dia |
| 402 | Sand cast iron S&S pipe as per IS: 1729 HSR 22.51.1.1 |
| 403 | 75 mm diameter |
| 404 | Sand cast iron S&S pipe as per IS: 1729 HSR 22.51.2.1 |
| 405 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1 :2 ( 1 cement: 2 fine sand) in S.C.1./ C.I. Pipes: HSR 22.52 |
| 406 | 75 mm dia pipe HSR 22.52.1 |
| 407 | 100 mm dia pipe HSR 22.52.2 |
| 408 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.HSR 22.66 |
| 409 | 100x100 mm size P type |
| 410 | With common burnt clay non-modular bricks of class designation 7 .5 .HSR 22.66.1.1 |
| 411 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1 :4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x61 O mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1: 1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 : 3 ( 1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.HSR 22.79 |
| 412 | Inside dimensions 455x610 mm and 45 cm deep for single pipe line : |
| 413 | With common burnt clay non-modular bricks of class designation 7 .5 HSR 22.79.1.1 |
| 414 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.HSR 22.80 |
| 415 | 100 mm inlet and 75 mm outlet. 22.80.2 |
| 416 | Sand cast iron S&S as per IS - 3989 HSR 22.80.2.1 |
| 417 | Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay non-modular bricks HSR 22.82.1 |
| 418 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brassthreaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step CPVC solvent cement andthe cost of cutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.HSR 22.86. |
| 419 | Concealed work, including cutting chases and making good the walls etc. |
| 420 | 20 mm nominal outer dia Pipes |
| 421 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (HSR 22.103.2) 20 mm nominal bore |
| 422 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931HSR 22.104.1 |
| 423 | 15 mm nominal bore |
| 424 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.HSR 22.107 |
| 425 | Extra for depth beyond 45 cm of brick masonry chamber.HSR 22.180 |
| 426 | For 455x610 mm size |
| 427 | With common burnt clay non-modular bricks ofclass designation 7 .5.HSR 22.180.1.1 |
| 428 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately HSR 28.182 |
| 429 | 500 ltr capacity |
| 430 | Group A HSR 23.2.1.1 |
| 431 | Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. switch in 1.5sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group A HSR 23.2.2.1 |
| 432 | Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe, without separate control switch.HSR 23.1.3 long point |
| 433 | Wiring in MS conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin socket and 1 no 5/6 Amp switch required MS Box etc complete as required.Group A HSR 23.1.4 |
| 434 | Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin socket and 1 no 15/16 Amp switch required MS Box etc complete as required.Group A HSR 23.1.5 |
| 435 | MS CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS.HSR 23.6 |
| 436 | MS CONDUIT and MS/GI BOX only for LIGHT/FAN/Call bell point wiring.23.6.1 |
| 437 | Group A |
| 438 | Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect.23.8 |
| 439 | Switch 5 amp. on existing sheet.HSR 23.8.1 |
| 440 | Wall socket 5 amp on existing sheetHSR 23.8.1.2 |
| 441 | 15 amp. switch on existing sheet.HSR 23.8.1.3 |
| 442 | 6 pin 15 multi socket on existing sheetHSR 23.8.1.4 |
| 443 | Supply and Fixing Bakelite sheet on existing MS/GI/wooden/PVC box etc including fixing with brass screws and washers.HSR 23.8.2.2 |
| 444 | 3mm thick |
| 445 | Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm each 106 long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job.HSR 23.8.4 |
| 446 | Copper Wiring in MS Conduit (Surface / Recess) |
| 447 | Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. |
| 448 | Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling including cutting/making hole in ceiling including making connections etc as required.HSR 23.21 |
| 449 | Earthing and Lightening Arrestor.HSR 24.1 |
| 450 | Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required HSR 24.1.1 |
| 451 | Extra for using salt and char coal/coke for pipe earth electrode as required .HSR 24.1.2 |
| 452 | Supply of GI class B |
| 453 | Code B1140-G.I. pipes 15 mm dia |
| 454 | Code B1141- G.I. pipes 20 mm dia |
| 455 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement sluny mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/ sqm This layer will be allowed to air cure for 4 hours. (b) Second layer of sluny of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.HSR 28.15 |
| 456 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm(b) laying second layer of Fibre glass cloth when the first layer is still green. verlaps of joints of fibre cloth should not be less than 10cm.(c) third layer of 1.5 mm thickness consisting of sluny of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately). For the purpose of measurement the entire treated surface will be measured. (HSR 28.16) |
| 457 | Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1: 1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manne HSR 28.43 |
| 458 | Total amount Estate |
| 459 | Estate NS ITEMS |
| 460 | Provision for construction of brick masonry sluice valve chamber, as per PHED standard, complete in all respect. (approved rate of PHED) NS |
| 461 | Cost of making water supply connection from main line to boosting station with 150 mm dia pipe including specials and sluice valve etc., complete in all respect. |
| 462 | Cost of construction of pump chamber of size 3.05m x 4.30m complete as per analysis attached. |
| 463 | Cost of providing and fixingCI pipes and special inside pump chamber L.S. |
| 464 | Cost of construction of 1Nos. RCC under ground collecting tanks of size 3m x 3m x 3m(avg depth) with capacity 27000 ltr open to sky along with screening chamber of size 0.60m x 2m. |
| 465 | 27000 @ Rs.7.50 per ltr |
| 466 | Cost of construction of pump chamber of size 3.05m x 4.30m complete as per analysis attached. |
| 467 | Cost of providing and fixing CI pipes and special inside pump chamberL.S |
| 468 | Cost of construction of boundary wall as per standard drawing complete as per analysis attached. |
| 469 | 250 Mtrs @ Rs. 5065.00 per mtr. |
| 470 | Construction of 1 nos. staff quarter of size 46sqm each complete as per analysis attached. |
| 471 | 1 Nos @ Rs. 660000.00 |
| 472 | Cost on account of security/connection fee etc. payable to DHBVNL |
| 473 | Provision for misc. items such as roads, street lights, plantation and site laying etc |
| 474 | Providing and fixing of one no. iron main and wicket gate as per detail enclosed. |
| 475 | 1 No @ Rs. 31075.00 each |
| 476 | The price for design, Supply, installation testing and commissioning of 150 KLD Daiki Axis Packaged STP plant on Johkasou technology as per above mentioned scope of work. |
| 477 | BOOSTING STATION |
| 478 | Design, Supply & erection of transformer of standard make Required 15 KVA 11/0.433 KVA rating outdoor type 11 KVA V.C.B, panel, G.O. switch, H. Pole , H.T metering panel, APFC panel, battery charges, 11 KVA substation, entire cable network from G.O. switch to H.T metering equipment and from H.T metering to Transformer. From transformer to main to L.T, panel earthling, safety equipment, fenced enclosure for transformer, and any other contingent thereto complete in all respect as per approved make and directions of Engineer-in-charge as per respective capacity. HSR 20.76 |
| 479 | 15 KVA = 1 No. @ Rs. 76478.00 each HSR 20.76.1 |
| 480 | Supply & erection of "Wall Mounting Type, solenoid driven, motorized, electromagnetic diaphragm Dozing Metering pump working on three-phase 220/240 V 50 Hz electric supply with standard electronic controls, suitable for minimum dozing capacity O to 27 LPH at 10 bar back pressure" complete with necessary accessories, complete in all respects along with supply and erection of 1 No. Voltage Stabilizer with Dozing Pump along with 1 No. 300 litres capacity ISi marked HOPE storage tank of approved make as per directions of Engineer-in-charge.. HSR 20.87 |
| 481 | 1 No @ Rs.21814.00 each |
| 482 | Supplying, erection, testing and commissioning of Horizontal motor pumping set for clear water having head 30.00 m as per the indicated requirements of discharge in 400 LPM and power capacity in BHP Make: KSB, CRI, Kirlosker, Crompton Greeve, Lubi) HSR 20.119 |
| 483 | 2 Nos @ Rs.107049.00 each HSR 20.119.1 |
| 484 | Cost of Disposal Work |
| 485 | Design, Supply & erection of transformer of standard make Required 15 KVA 11/0.433 KVA rating outdoor type 11 KVA V.C.B, panel, G.O. switch, H. Pole , H.T metering panel, APFC panel, battery charges, 11 KVA substation, entire cable network from G.O. switch to H.T metering equipment and from H.T metering to Transformer. From transformer to main to L.T, panel earthling, safety equipment, fenced enclosure for transformer, and any other contingent thereto complete in all respect as per approved make and directions of Engineer-in-charge as per respective capacity. HSR 20.76 |
| 486 | 15 KVA = 1 No. @ Rs. 76478.00 each HSR 20.76.1 |
| 487 | Supplying, erection, testing and commissioning of submersible motor pumping set non clog for sewerage having head 15.00m as per the indicated requirements of discharge in LPM and power capacity in BHP make: KSB, CRI, Kirlosker, Crompton Greeve, Lubi) HSR 21.106 |
| 488 | 2 BHP - (2 Nos @ Rs. 61286.00 each) 21.106.7 |
| 489 | Supplying, erection, testing and commissioning of submersible motor pumping set non clog for sewerage having head 15.00m as per the indicated requirements of discharge in LPM and power capacity in BHP make: KSB, CRI, Kirlosker, Crompton Greeve, Lubi) HSR 21.106 |
| 490 | 5 BHP - (2 Nos @ Rs. 71674.00 each) |
| 491 | COST OF PUMPING MACHINERY |
| 492 | Supplying, erection, testing and commissioning of Horizontal motor pumping set for clear water having head 20.00 m as per the indicated requirements of discharge in 400 LPM and power capacity in BHP Make: KSB, CRI, Kirlosker, Crompton Greeve, Lubi) HSR 20.115 |
| 493 | 2 Nos @ Rs.95783.00 each HSR 20.115.1 |
| 494 | Estate services Amount |
| 495 | Horlticulture Items |
| 496 | Turfing lawns with fine grassing ( selection no.1/ Bermuda and Mexican/Neelgiri grass )including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying of selection no. 1 / Bermuda doob grass and Mexican/Neelgiri grass roots, including supplying and spreading of farmyard manure at the rate of 0.60 cum per 100 sqm, maintenance till weed free turf is formed Planting selection no. 1 grass roots in rows 5 cm apart in both directions(HSR No. 26.9.2) |
| 497 | Supplying and stacking at site of work well-decayed farm-yard manure from any available source, approved by the Engineer-incharge including screening through sieve of LS.designation 16 mm with 5 km lead(HSR No. 26.1) |
| 498 | Spreading of sludge, farm-yard manure or/and good earth in required thickness (Cost of sludge, farm-yard manure or/and good earth to be paid for separately) HSR 26.3.6 |
| 499 | Supplying and planting in prepared pits and watering, healthy , each vigorous growing , permanent trees including ,application of 10 ml chlorpyriphos 20% EC, planting desired disease free, 200 cm to 220 cm height ,5 cm to 6 cm calliper size stem , full of foliage ornamental tree sapling each to be supplied in 30cm x 30cm poly bags.(HSR No. 26.14) |
| 500 | Supply and planting of disease free healthy , vigorous growing more each than 75 cm height permanent shrubs in already prepared pits, supplied in 25 cm x 20 cm poly bags , application of 10 ml chlorpyriphos 20% E.C. termiticide each and watering supplied through the tractor tanker(HSR No. 26.18) |
| 501 | Supply and Planting rare and specimen tree plants in already each prepared pits (Ficus starlight 150 cm height , Terminalia 210 cm height, menatalis , Michelia champaca hybrid more than 180 cm height, Cyprus (Golden juniperous) more than 180 cm height, topiary of 10 to 12 no. well trimmed bolls of more than 30cm size of Ficus nuda, Ficus retusa, Ficus long island , Ficus panda more than 180 cm height, Golden bottle brush , casurina equistefolia , Bottle palm with stem circumference at base more than 40cm ,Washingtonia palm of healthy clear stem height below leaf more Thant 90 cm) including , fertilizer and insecticides chlorpyriphos 20 ml per pit, planting of 180cm to 210cm tall sapling in position and flooding with water,specie of plant will be decided by engineer in charge.(HSR No. 26.20) |
| 502 | Supply and planting flower beds including digging 30 cm sqm deep bed and refilling of beds with excavated soil and FYM 0.0508 cum per sqm , Fertilizer DAP 50 gms and insecticides chlorpyriphos 10 ml per sqm , planting of F1 hybrid flower saplings to be supplied in tray pots / thumb pots at 20 cm distance from plant to plant and row to row minimum 25 no . plants per sqm(HSR No. 26.22.1) |
| 503 | Supply and planting ground cover plants including digging 30 cm sqm deep bed and refilling of beds with excavated soil and FYM 0.0508 cum per sqm , Fertilizer DAP 50 gms and insecticides chlorpyriphos 10ml per sqm , planting of saplings at 23cm distance from plant to plant and row to row, minimum 19 no. plants per sqm(HSR No. 26.26) |
| 504 | Supplying healthy, well branched, well bloomed and Planting rose beds including digging 30 cm deep bed and refilling of beds with excavated soil and FYM 0.0508 cum per sqm , Fertilizer DAP 50 gms and insecticides chlorpyriphos 10ml per sqm , planting of hybrid Budded rose saplings to be supplied in earthen pots 120cm x20cm polybags , planting of sapling at 45 cm distance from plant to plant and row to row and 5 no. plants per sqm(HSR No. 26.30) |
| 505 | Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth, mixed with farmyard manure, supplied at the rate of 1.62 cum per 18 sqm, DAP 0.6kg, Chlorpyriphos 20%EC@ 0.20 litre per 18 sqm and supplying and planting hedge at 30 cm apart in two rows @ 202 no. well trimmed bushy ,multi-branched ,30 cm to 45 cm in height plants to be supplied in 15 cm x 15 cm poly bags per 18 sqm.(HSR No. 26.34) |
| 506 | Supplying decorative plant in 30 cm cement pots for outdoor display at site of work with fresh foliage of 60cm-75 cm in height" 3-4 stems per pot, full of leaves, suitable for earthen pots / plastic pots size 30cm dia and 30cm deep(average size) and displaying including the cost of material ( garden soil, coco peat, FYM in2:1 :1 proportion),with ,PVC plate. complete in all respects.(HSR No. 26.48) |
| 507 | Supplying and display indoor decorative plants with fresh foliage,60cm-75 cm in height" 3-4 stems per pot, full of leaves, suitable for earthen pots / plastic pots size 30cm dia and 30cm deep(average size),and displaying indoor including the cost of material ( garden soil, coco peat, FYM in2:1 :1 proportion),with ,PVC plate. complete in all respects including cost of pot.(HSR No. 26.44.2 In Earthen Pot) |
| 508 | Preparation of mounds of various size and shapes including supply of cum good earth, in layers not exceeding 20 cm in depth, breaking of clods, watering each layer, dressing etc, lead up to 50 m and lift up to 1.5 m complete as per directions (excluding cost of good earth and manure which will be supplied separately.)HSR No. 26.52 |
| 509 | Chair type garden bench with L-shaped sides made of reinforced concrete (M30), thickness 100 mm, overall height 1000 mm, base width 620 mm. Back and seat shall consist of 5 Nos. reinforced concrete planks 1500 mm x 100 mm x 50 mm one plank 1500 mm x 200 mm x 50 mm. Seating height of the bench shall be 450 mm. The bench shall be fixed with nuts on concrete mount, all holes sealed after assembly and installation. All materials required to be as per BIS specifications.(HSR No. 26.58.1) |
| 510 | Supplying and stacking of good quality top layer garden earth free from debris and weeds, at site including royalty and carriage/lead 5 km (good earth measured in stacks will be reduced by 20 % for payment) only for filling of pots and flower beds. |
| 511 | Maintenance of fine grass lawn for one year including fertilizer application, DAP @ 20gm/sqm, urea 40gm/sqm, watering, weeding, top dressing with good earth and manure mixture 2:1 @ 0.01cum per sqm, maintaining fine level, regular mowing and removal of rubbish with all lifts and leads(HSR No. 26.10) |
| 512 | Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farmyard manure (cost of well decayed farm yard manure to be paid separately)HSR No. 26.13.4 - Hole 0.60 metre dia and 0.60 metre deep |
| 513 | Supply of well grinded in powder form De-oiled Neem cake in packed gunny bags(HSR No. 26.77) |
| 514 | Horlticulture Amount |
| 515 | E.I Items |
| 516 | (HSR 20.71) Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge. |
| 517 | 1. 48" (1200mm) |
| 518 | 2. 56" (1400mm) |
| 519 | (HSR-23.4) COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT |
| 520 | (HSR-23.4.1) Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe |
| 521 | 1) Group A |
| 522 | 2) Group B |
| 523 | 3) Group C |
| 524 | (HSR-23.4.2) Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. |
| 525 | 1) Group A |
| 526 | 2) Group B |
| 527 | 3) Group C |
| 528 | (HSR-23.4.4) Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required |
| 529 | 1) Group A |
| 530 | 2) Group B |
| 531 | 3) Group C |
| 532 | (HSR-23.4.5) Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling, including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required |
| 533 | 1) Group A |
| 534 | 2) Group B |
| 535 | 3) Group C |
| 536 | (HSR-23.5.6 ) Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. |
| 537 | 1) 1 run of Size 1.50 Sqmm(1/1.40mm) |
| 538 | 2) 1 run of Size 2.50 Sqmm(1.1.80mm) |
| 539 | 3) 1 run of Size 4 Sqmm(1/2.24mm). |
| 540 | 4) 1 run of Size 6 Sqmm(1/2.80mm) |
| 541 | 5) 1 run of Size 10 Sqmm(1/3.50 mm) |
| 542 | (HSR-23.7.6) Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. |
| 543 | Note: The rates worked out for items 23.1 to 23.7 and their sub-items are by considering recessed conduit wiring. These rates may be reduced by 15% wherever surface conduiting wiring is required to be done as per directions of Engineer-in-Charge. |
| 544 | 1) PVC pipe of 20 mm dia. |
| 545 | 2) PVC pipe of 25 mm dia. |
| 546 | 3) PVC pipe of 32 mm dia. |
| 547 | 4) PVC pipe of 40 mm dia. |
| 548 | (HSR-23.8.1) Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. |
| 549 | 23.8.1.12) Bakelite angle/straight button holder large size. |
| 550 | ( HSR - 23.8.10 ) Providing and fixing GI concealed sheet metal boxes with inner and outer surface plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. |
| 551 | 23.8.10 .1) 1 & 2 Modules including combined plate for Telephone and data |
| 552 | 23.8.10 .4) 6 Modules |
| 553 | (HSR- 23.8.11) Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. |
| 554 | 23.8.11.7)step type Fan Regulator 2 modules 300 watt |
| 555 | 23.8.11.8) Telephone Socket outlet modular type |
| 556 | 23.8.11.10) Blanking plate |
| 557 | 23.8.11.11) RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type |
| 558 | (HSR-23.8.12) Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction box/tee etc including fixing with brass screws and washers. |
| 559 | (HSR-23.13) Supply, erection and fixing of 12 mm thick ply wood board having a circular /rectangular hole etc as required including the cost of making hole, nuts and bolts, painting and other petty material with all labour etc. complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. |
| 560 | (HSR-23.22) MCCB ,DISTRIBUTION BOARDS, MCB"s, RCCB"s, CHANGE OVER etc |
| 561 | HSR 23.22.1)Supply and erection of Modular case circult breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections requried to complete the job in all respect up to the entire satisfaction of the Engineer-in charge of the work. |
| 562 | 23.22.1.9 ) 4 pole MCCB 6 amp to 100 amp, 25 KA |
| 563 | 23.22.1.10 ) 4 pole MCCB 125 amp to 160 amp, 25 KA |
| 564 | (HSR 23.22.2) Supply and erection of MCCB Enclosure made of sheet steel suitable for mounting MCCBof following ratings |
| 565 | 23.22.2.1 )MCCB up to 125 A FP |
| 566 | 23.22.2.2 )MCCB up to 250 A FP |
| 567 | (HSR 23.22.4) Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. |
| 568 | 23.22.4.3) SPN DB Double Door 12 way ( 2 incoming and 10 outgoing) |
| 569 | 23.22.4.9) Vertical TPN DB Double Door 4 way ( 8 incoming and 3phase*4 outgoing) |
| 570 | 23.22.4.11) Vertical TPN DB Double Door 8 way ( 8 incoming and 3phase*8 outgoing) |
| 571 | (HSR - 23.22.5) Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- |
| 572 | 23.22.5.1)6 amp. to 32 amp Single Pole |
| 573 | 23.22.5.4)40 amp to 63 amp. Double pole |
| 574 | 23.22.5.6) 40 amp to 63 amp. MCB"s TRIPLE POLE |
| 575 | 23.22.5.8) 40 amp to 63 amp. MCB"s FOUR POLE |
| 576 | HSR-23.22.8 )SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings |
| 577 | 23.22.8.3)200 amp 415 volts |
| 578 | HSR-23.23.1) Supply and fixing Galvanised Iron flexible pipe complete with socket nipples and check nuts etc. at both ends (Up to length of one metre):- |
| 579 | 23.23.1.1)Size 15 mm dia |
| 580 | 23.23.1.2) Size 25 mm dia |
| 581 | (HSR-23.23.5) Supply and erection of U- PVC Trunking/Channel of following size including cost of fixing on wall, floor and ceiling etc. with required material complete the job in all respect up to entire satisfaction of the Engineer-in-charge of work. |
| 582 | 23.23.5.1)25x 12 mm |
| 583 | 23.23.5.2) 38x 12 mm |
| 584 | (HSR- 23.23.8) Supply and laying of multicore telephone cable conductor size 0.51 mmbright annealed copper conductor PVC insulated and sealed in existingpipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. |
| 585 | 23.23.8.1) 2 pair telephone wire |
| 586 | 23.23.8.2) 4 pair telephone wire |
| 587 | (HSR- 23.23.9) Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required |
| 588 | (HSR 24.1)EARTHING AND LIGHTENING ARRESTOR |
| 589 | 24.1.1) Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. |
| 590 | 24.1.2) Extra for using salt and char coal/coke for pipe earth electrode as required |
| 591 | 24.1.3) Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick includingaccessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. |
| 592 | 24.1.4)Earthing with tinned copper earth plate 600mmx600mmx3mm thickincluding accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. |
| 593 | 24.1.5) Extra for charcoal or coke and salt for G. I. plate or copper plate earthelectrode. |
| 594 | 24.1.8) Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. |
| 595 | 24.1.10)Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. |
| 596 | 24.1.13) Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. |
| 597 | 24.1.14) Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of same size. |
| 598 | (HSR-24.2.4) Laying of underground cable in pipe /existing open/closed trench etc as |
| 599 | 24.2.4.2)16 Sq mm to 35 sqmm 2 to 4 Core |
| 600 | 24.2.4.3)50 Sq mm to 150 sqmm 2 to 4 Core |
| 601 | 24.2.3.4 ) 185sqmm to 240 sqmm 3 to 3.5 Core |
| 602 | ( HSR-24.2.6) Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. |
| 603 | 24.2.6.1)1.5 sqmm |
| 604 | 24.2.6.2 ) 2.5sqmm |
| 605 | 24.2.6.3 ) 4sqmm |
| 606 | 24.2.6.4)6sqmm |
| 607 | 24.2.6.5)10 sqmm |
| 608 | (HSR 24.2.7 ) Supply and erection of suitable compression type brass cable glands for underground Cable :- |
| 609 | 24.2.7.2) 10 sqmm to 16 sqmm Cable 2 to 4 Core |
| 610 | 24.2.7.3) 25 sqmm to 50 sqmm Cable 2 to 4 Core |
| 611 | 24.2.7.4) 70 sqmm to 95 sqmm Cable 3 to 3.5 Core |
| 612 | 24.2.7.5) 120 sqmm to 185 sqmm Cable 3 to 3.5 Core |
| 613 | 24.2.7.6) 240 sqmm to Cable 3 to 3.5 Core |
| 614 | (HSR 24.2.8) Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work . |
| 615 | 24.2.8.4) 16sqmm |
| 616 | 24.2.8.5) 25sqmm |
| 617 | 24.2.8.6) 35sqmm |
| 618 | 24.2.8.7) 50sqmm |
| 619 | 24.2.8.9) 95sqmm |
| 620 | 24.2.8.10) 120 sqmm |
| 621 | 24.2.8.12) 185 sqmm |
| 622 | 24.2.8.13) 240 sqmm |
| 623 | SAFETY ITEMS HSR-23.26 |
| 624 | HSR-23.24.3)Supply and erection of metal clad bus-bar chamber made from 1.6mm thick M.S. sheet and fixing with rag bolts on wall or on existing pedestal/angle iron frame including bonding, detachable top and bottom including painting and necessary connection etc.(Alluminium bars ) |
| 625 | 23.24.3.2) 100 amp. 4 bars of 100cm each (cross section 25mm x 6mm ) chamber overall size 60m x 45cm x 18cm. |
| 626 | (HSR-23.26.1) Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages |
| 627 | ( HSR-23.26.2)Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages. |
| 628 | ( HSR-23.26.3) Supply and erection of shock restoration chart in glass frame. |
| 629 | (HSR-23.26.4) Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire buckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6"x4" made of GI pipe 32mm dia). |
| 630 | HSR-20.84) Providing and fixing of insulated rubber matting suitable for 11 KV installation 1 M x 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per directions of Engineer-in-charge |
| 631 | G.O. SWITCH (HSR-20.86) Supply, erection, testing & commissioning of G.O. Switch two poles, with blade, pin 6 insulators operating handle with GI pipe 25 mm class B complete in all respects. |
| 632 | HSR-20.88 ) Supply, erection, testing and commissioning of CT meter of standard make each with cubical meter box as per HVPNL specifications including 3 phase electrical meter 100/5 of standard make approved by HVPNL including CT/PT of suitable rating complete in all respect as per directions of Engineer-in-charge. |
| 633 | HSR-24.2.10 ) Supply and erection of cable route marker made of 50 cm long 10 mm diaM.S. Rod welded/riveted at the top with 10 cm dia 3 mm thick MS plate inscribed with "cable" word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in exiting trench 45 cm below ground level. |
| 634 | HSR-24.3.1 ) Laying and erection of XLPE E II kv HT aluminium conductor armoured cable 1 metre below ground level with sand & bricks with all labour and material including digging and refilling of trench as required. |
| 635 | 24.3.1.1)up to 120 sqmm 3 core XLPE Cable |
| 636 | HSR-24.3.3 ) Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required |
| 637 | 24.3.3.1)70 to 120 sqmm |
| 638 | HSR- 24.3.4 ) Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required |
| 639 | 24.3.4.1)70 to 120 sqmm |
| 640 | HSR-24.4.17) Supply and erection of weather proof M.S. box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S. sheet hinged cover, housed in 1 :3:6 cement concrete muff including suitable size of PVC pipe for in coming and out going cables, including the cost of 1 no. 16 amp. 415 volts SP MCB and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board/B mm Bakellite sheet in the M.S. box including the cost of locking arrangement ,painting and necessary connections etc. (Muff size 40 cm dia 50 cm high) |
| 641 | HSR-24.4.8) Supply & Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts, earthing studs,internal cable termination arrangements 5mm thick bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2no. 10A SP MCB, end cover and all acessories as supplied by the manufacturer including providing RCC foundation of M25 grade (1 Cement 1 Stone aggregate 2 coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 80kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions fo roctagonal poles of various heights as per following specifications completein all respect and as per direction of Engineer in-charge . |
| 642 | 24.4.8.5 ) 7 Mtr. Long pole with top dia 75.0mm and botom dia 150mm with base plate of size 3000 x 300 x 20mm. |
| 643 | HSR-24.4.15.3) Supply, installation, testing and commissioning of 20 mtr. longHigh Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge. Thickness of Top and Bottom Section = 3 mm & 4mm (minimum), Top Dia = 150 mm and Bottom Dia = 460mm, Thickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum) |
| 644 | (HSR-24.5.2)S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/ coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. |
| 645 | 24.5.2.3)DWC/HDPE pipe 63/50 mm outer dialinner dia |
| 646 | 24.5.2.4)DWC/HDPE pipe 90/75 mm outer dialinner dia |
| 647 | 24.5.2.5)DWC/HDPE pipe 120/102 mm outer dialinner dia |
| 648 | 24.5.2.6)DWC/HDPE pipe 145/123 mm outer dialinner dia |
| 649 | RCC Foundation for D.G Set (HSR-24.7) |
| 650 | Providing RCC foundation of M-20 grade (1 cement :1.5 stone aggregate : 3 coarse sand) i/c excavation , steel reinforcement (Fe500) @ 50kg/cum of concrete contents, concrete cover 50mm over a bed of 75mm thick PCC 1:5:10 of required dimensions as per OEM recommendations to provide levelled surface for placement of DG Set complete in all respect and as per directions of Engineer-in-charge.(Size of foundation assumed = (5.0 x 1.80 x 1.0 )mtr. unit per cum. Note- As size and dynamic load of DG Set vary from manufacturer to manufacturer, item of DG Set foundation have been included on the basis of cubic contents of RCC. |
| 651 | 24.7.2) 60 TO 90 KVA DG Set |
| 652 | ( HSR-32.70)SOLAR PANELS Supply Installation testing commissioning of Solar Photovoltaic grid connected roof top Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- (a) Solar Photovoltaic Module manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part 2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 1 O years and 80% at the end of 25 years. (b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC (c) Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from O to 50 degrees C. The PCU shall adjust the voltage and frequency level to suit grid frequency |
| 653 | (d) Data Monitoring System complete with accessories. (e) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. (f) Lightning and surge voltage protection. (g) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required |
| 654 | (d) Data Monitoring System complete with accessories. (e) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc.as required. (f) Lightning and surge voltage protection. (g) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required |
| 655 | 32.70.1 Above 1 kWp and up to 10 Kwp |
| 656 | 32.70.2 Above 10 kWp and up to 100 Kwp |
| 657 | HSR Estate Electrical Total |
| 658 | DSR ITEMS(Fire Fighting) |
| 659 | FIRE DETECTION AND ALARM SYSTEM(CONVENTIONAL) DSR ( 17.1) |
| 660 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. ( DSR 17.1.2) |
| 661 | supply, installation,testing & Commisioning of manual call boxes of M.S.Construvtionall point in surface/ Recess with stainless steel chain & hammer assembely complete with glass & push button etc. as required. ( DSR 17.1.3) |
| 662 | supply, installation,testing & Commisioning fire alarm sounder with facility to make annoucement , mounted in ABS Box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. ( DSR 17.1.7) |
| 663 | Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. 6 zone panel for fire alarm system 100 watt amplifier racks suitable for operation on 230VAC/24V DC supply conforming to IEC-268-3 complete with all accessories as required- 2 Nos.(one to act as standby) (DSR 17.1.11) |
| 664 | TOTAL DSR AMOUNT(Fire Fighting) |
| 665 | NS item |
| 666 | Supply of LT Armoured Cable of following 1100 volt and complete with making necessary connection of cable on both ends including loading unloading & carriage with all labour and petty material required to complete the job upto the entire staisfaction of Engineer - In - Charge of the work. |
| 667 | 1)LT Armoured Cable of size 16 sqmm 2 core |
| 668 | 2)LT Armoured Cable of size 16 sqmm 4 core |
| 669 | 3)LT Armoured Cable of size 25 sqmm 4 core |
| 670 | 4)LT Armoured Cable of size 35 sqmm 4 core |
| 671 | 4)LT Armoured Cable of size 50 sqmm 3.5 core |
| 672 | 5)LT Armoured Cable of size 70 sqmm 3.5 core |
| 673 | 6)LT Armoured Cable of size 95 sqmm 3.5 core |
| 674 | 6)LT Armoured Cable of size 150 sqmm 3.5 core |
| 675 | 6)LT Armoured Cable of size 240 sqmm 3.5 core |
| 676 | Supply and erection of surface/ Recessed mounting, energy efficient LED 6000 K round luminaire, complete with diffuser, HF electronic driver and other material required to complete the job including fixing the same in false ceiling with required material & making necessary connections etc :- |
| 677 | i) LED 36W surface mounting 2"x2" Panel |
| 678 | ii) LED 18 W Square Fitting surface mounting |
| 679 | Supply and erection of surface mounting LED Batten fitting 1x 20 watt, (4 feet long), made of high grade poly carbonate body provided for efficient heat dissipation & integrated electronic driver suitable for single phase A.C. 230 Volts, 50 HZ supply, complete in all respect. ( BAJAJ Model - BCLSB 18 W or equivalent model of Makes as per approved brand list ) |
| 680 | Supply and erection of surface mounting LED Batten fitting 1x 10 watt, (2 feet long), made of high grade poly carbonate body provided for efficient heat dissipation & integrated electronic driver suitable for single phase A.C. 230 Volts, 50 HZ supply, complete in all respect. ( BAJAJ Model - BCLSB 10 W or equivalent model of Makes as per approved brand list ) |
| 681 | Supply, installation, testing and commissioning of 10W LED Bulkhead light fixture with necessary driver lamp, connections, wiring & etc. complying to IP 65 class of protectioncomplete as required. (Bajaj:BIBWP 10W LEDor equivalent model of Makes as per approved brand list) |
| 682 | Supply, installation, testing and commissioning of 15W/ Meter LED Strip light fixture with connections, wiring & etc. complying to IP 65 class of protection complete as required. (Bajaj:BCFL 300 75W IP-65 or equivalent model of other approved brands) (Drivers to be ordered separately) |
| 683 | Supply, installation, testing and commissioning of 27W LED Facade light fixture with 30x30 Deg. beam angle and necessary driver, lamp, connections, wiring & etc. complying to IP 66 class of protection complete as required. (Philips :-UniFlood C Small or equivalent model of Makes as per approved brand list) |
| 684 | S/E of fresh air fans (Exhaust fan) 200mm sweep PVC body with louver shutter, suitable for single phase A.C. 230 Volts, 50 HZ supply complete with all labour and petty material required to complete the job. (Havell"s-Make & Model-Ventlair DX / Crompton Greaves-Make & Model-Brisk Air) |
| 685 | S/Eof fresh air fans (Exhaust fan) 250mm sweep PVC body with louver shutter, suitable for single phase A.C. 230 Volts, 50 HZ supply complete with all labour and petty material required to complete the job. (Havell"s-Make & Model-Ventlair DX / Crompton Greaves-Make & Model-Brisk Air) |
| 686 | S/E of ISImarked propeller type ventilation fans (Exhaust fan)Size 300 mm, 1400 rpm Heavy Duty suitable for single phase A.C. 230 Volts, 50 HZ supply, A.C capacitor run conferming to IS:23/2/67 , complete with mounting ring with four no.s fixing holes without regulator as per rate contract specifications.with all labour and petty material required. |
| 687 | Supply and erection of 300 mm aluminium anodized louver shutter for exhaust fan (Thickness of frame 1.00 mm & blade thickness 0.80 mm) including all labour and other petty material required to complete the job. |
| 688 | ii) 25A/10A 6pin modular type socket (for AC point) |
| 689 | iii) Motor starter 25 amp, 2 moudle (for AC point) |
| 690 | v) Modular TV socket |
| 691 | S/E of co-axial TV cable (RG-6) with electrolytic grade solid bare copper conductor, gas injected physical foamed polythylene insulation, screened with laminated aluminium tape & aluminium alloy wire braided, jelly flooded & UV grade PVC jacketed in existing pipe, complete in all respect including making necessary connections and labour etc. |
| 692 | S/I/T/C of water cooler stainless steel body with 150 ltr /hr and 150 ltr storage capacity (USHA,Sidwal,Voltas Make) complete in all respect i/c all labour and petty material. |
| 693 | Supply &Erection ofCommercial Mineral RO systemof 50 Ltr/ hr. water Purification Capacityi/c fixing on wall with all petty material and labour reqd. (Make-Kent &Eureka Forbes ) or its equivalent from approved list of make. |
| 694 | Supply, Testing & Commissioning of wall fan 16" sweep (400mm) Oscillating type complete with built-in regulator. The fan is to fixed on wall with suitable fixing arrangement including connection from nearest light point with cost of Cu wire required (Make-Havell"s & Model-PLATINA / Crompton make & Model-HIGH FLOW LG White only) .. |
| 695 | S/I/T/C of high wall1.5 TR capacity invertor type of 5 Star rating SplitAir- conditioning unitrated at 220 volts (+) (-) 10%,single phase, 50 cycle per second electric supply and consisting of condensing and indoor unit,control panel of the unit, LCD Cordless remote, internal control wiring, thermostats, all accessories , , MS stand & 4 KVA three step wall mount voltage stablizer and first charge ofGas & oil but with 3 meter copper refrigerant & drain pipe. The work shouldbe completed in all respect including making repair of wall,floor and roof in original shape caused by making holesand chases etc. |
| 696 | S/I/T/C of high wall2.0 TR capacity invertor type of 5 Star rating SplitAir- conditioning unitrated at 220 volts (+) (-) 10%,single phase, 50 cycle per second electric supply and consisting of condensing and indoor unit,control panel of the unit, LCD Cordless remote, internal control wiring, thermostats, all accessories , , MS stand & 5 KVA three step wall mount voltage stablizer and first charge ofGas & oil but with 3 meter copper refrigerant & drain pipe. The work shouldbe completed in all respect including making repair of wall,floor and roof in original shape caused by making holesand chases etc. |
| 697 | S/I/T/Cof 2.0 TR invertor typeCassetteAir-conditioning unit of 5 Star rating to be operated on 220Volts(+) (-) 10% single phase,50 Hz AC supply and consisting of condensing indoor unit,cordless remote, 5 KVA wall mountvoltage stablizerwith MS stand & first charge of Gas & oil but W/Ohard copper refrigerant & drain pipe.The work should be completed in all respect i/c making repair of wall,floor and roof in origional shape caused by making holes and chases etc. |
| 698 | S/I/T/C of refrigerant piping made of good quality copper tube with insulation & copper wire of reqd.size for1.5/2.0 TR cap Split /CassetteAir Conditioneron wall/Ceiling Complete with all labour and petty material required to complete the job. |
| 699 | S/E of2250 VA Invertor sinwave type with Digital Display ( Luminious / Microtek / Sukem) suitable for operation on single phase 230 volts, 50 HZ, AC supply with2 nos 150 AH Exide batteries having guarannty of 2 years i/c cost of trolly for batteries complete with all labour and petty material required i/c making necessary connections upto entire staisfaction ofEngineer-in-Charge of the work. (Make-Luminious, Model-PRO2250) or equilent model ofMicrotek / Sukem |
| 700 | Supply and rection of vertical double door sheet enclosure distribution board (IP 43) suitable for MCCB as incomer recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work. |
| 701 | i) 4 way, TPN (Vertical, MCCBprovision for 100A-125A MCCB 4P and provision for 12 Nos. 6A-30A MCB SP as outgoings) |
| 702 | ii) 8 way, TPN (Vertical, MCCBprovision for 100A-125A MCCB 4P and provision for 24 Nos. 6A-30A MCB SP as outgoings) |
| 703 | S/E of Water Gyser Storage of 25Ltr/hr Capacity Verticalwith fixing of same on the wall and complete the job in all respect upto the entire satisfaction ofE- I - C. (AO Smith - Make) or Equilent approved brand of HPHC. |
| 704 | S/I/T/Cof 2.0 MEGA PIXEL DOME DAY/NIGHT IP CAMERA WITH ARTIFICIAL INTELLIGENCE (MAKE:- BOSCH/PELCO/SONY/ TEKWIN/AXIS/HONEYWELL/ HYUNDAI) complete in all respect upto the entire satisfaction of Engineer-in-Charge having as per following techanical specifications :- |
| 705 | IMAGE SENSOR- 1/2.9" CMOS |
| 706 | SIGNAL SYSTEM- PAL/NTSC |
| 707 | MIN. ILLUMINATION-COLOR: 0.02 LUX, B/W: 0 LUX WITH IR |
| 708 | SHUTTER TIME-1S TO 1/100,000S |
| 709 | LENS- 2.8MM, ANGLE OF VIEW: 109.3° |
| 710 | LENS MOUNT-M12 |
| 711 | DAY & NIGHT-IR CUT FILTER WITH AUTO SWITCH |
| 712 | WIDE DYNAMIC RANGE-D WDR |
| 713 | DIGITAL NOISE REDUCTION- 3D DNR |
| 714 | VIDEO COMPRESSION-S+265/H.265/H.264/M-JPEG |
| 715 | VIDEO BIT RATE- 32KBPS~8MBPS |
| 716 | AUDIO COMPRESSION- G.711/G.711U/ADPCM |
| 717 | AUDIO BIT RATE- 8K~48KBPS |
| 718 | MAX. IMAGE RESOLUTION-1920 x 1080 |
| 719 | FRAME RATE- PAL: 25FPS (1920×1080),NTSC: 30FPS (1920 ×1080) |
| 720 | MAIN STREAM- 1080P(1920 x 1080) |
| 721 | SUB STREAM- D1(704 x 576) |
| 722 | 3RD STREAM-CIF 352x288 |
| 723 | IMAGE SETTINGS-BRIGHTNESS, SATURATION, CONTRAST,FLIP MODE ADJUSTABLE BY CLIENT SOFTWARE OR WEB BROWSER |
| 724 | Support-HCL,BLC,Smart Defog,NTP & ANR |
| 725 | VIDEO Analytics-TRIPWIRE/PERIMETER/LINE CROSSING |
| 726 | ALARM TRIGGER-MOTION DETECTION/IP CONFLICT/MAC CONFLICT/PORT ALARM/MASK ALARM |
| 727 | PROTOCOLS -TCP/UDP/HTTP/MULTICAST/UPNP/ DHCP/DDNS/FTP/NTP/RTSP/SMTP/PPPOE |
| 728 | REMOTE CONNECTION =7 |
| 729 | SYSTEM COMPATIBILITY -ONVIF (PROFILE S/T/G) ,P2P, SDK, CGI |
| 730 | AUDIO INPUT- 1CH,Mic IN |
| 731 | AUDIO OUTPUT- Optional |
| 732 | ALARM INPUT - Optional |
| 733 | ALARM OUTPUT- Optional |
| 734 | VIDEO OUTPUT-Optional |
| 735 | COMMUNICATION INTERFACE-1-CH RJ45 10M / 100M ETHERNET INTERFACE |
| 736 | ON BOARD STORAGE -Micro SD Card Slot, upto 512GB |
| 737 | EXTENSION-Reset |
| 738 | Operating Conditions- (Minus -35?~60?, 0~95% RHG |
| 739 | POWER SUPPLY-DC 12 V ±25%, POE |
| 740 | Power Consumption-Max. 4W(ICR Instant Switch 8W) |
| 741 | IR LIGHT- 2 Dual IR Cut Filter with Auto Switch |
| 742 | IR DISTANCE- 30Mtr. |
| 743 | CERTIFICATION:- BIS, ULC, FCC, CE & CMMI |
| 744 | Impact Protection - IP67, Lighting Protection, Surge Protection and Voltage transient Protection meets EN: 55035:2017 |
| 745 | S/I/T/Cof 2.0 MEGA PIXEL BULLET IP CAMERA with ARTIFICIAL INTELLIGENCE (MAKE:- BOSCH/PELCO / SONY/TEKWIN/AXIS/HONEYWELL/ HYUNDAI) complete in all respect upto the entire satisfaction of Engineer-in-Charge having as per following techanical specifications :- |
| 746 | IMAGE SENSOR- 1/2.9" CMOS |
| 747 | SIGNAL SYSTEM- PAL/NTSC |
| 748 | MIN. ILLUMINATION-COLOR: 0.02 LUX BLACK & WHITE: 0.0 LUX WITH IR |
| 749 | SHUTTER TIME-1S TO 1/100,000S |
| 750 | LENS -4MM |
| 751 | LENS MOUNT-M12 |
| 752 | DAY & NIGHT-IR CUT FILTER WITH AUTO SWITCH |
| 753 | WIDE DYNAMIC RANGE-D DWR |
| 754 | DIGITAL NOISE REDUCTION- 3D DNR |
| 755 | FRAME RATE--1920 x 1080 |
| 756 | MAIN STREEM:- PAL: 25FPS (1920 × 1080), 25FPS (1280 × 720) NTSC: 30FPS (1920 × 1080), 30FPS (1280 × 720) |
| 757 | SUB STREAM - 1080P(1920 x 1080) |
| 758 | Support- Corridor format ,ROI ,Privacy mask , Picture overlay, NTP & ANR |
| 759 | AUDIO COMPRESION- Optional |
| 760 | AUDIO BIT RATE - Optional |
| 761 | NETWORK STORAGE -FTP |
| 762 | VIDEO Analytics-TRIPWIRE/PERIMETER/LINE CROSSING |
| 763 | ALARM TRIGGER-MOTION DETECTION/IP CONFLICT/MAC CONFLICT/PORT ALARM |
| 764 | PROTOCOLS- HTTP/802.1X/FTP/SMTP/UPNP/ SNMP/DNS/ DDNS/NTP/RTSP/TCP/UD P/DHCP/PPPOE |
| 765 | REMOTE CONNECTION =7 |
| 766 | SYSTEM COMPATIBILITY -ONVIF (PROFILE S) ,P2P, SDK, CGI |
| 767 | AUDIO INPUT- 1CH,Built in MIC |
| 768 | AUDIO OUTPUT-OPTIONAL |
| 769 | COMMUNICATION INTERFACE-1-CH RJ45 10M / 100M ETHERNET INTERFACE |
| 770 | ALARM INPUT -OPTIONAL |
| 771 | ALARM OUTPUT-OPTIONAL |
| 772 | ON-BOARD STORAGE- 1MICRO SDHC |
| 773 | EXTENSION-RS485 |
| 774 | Operating Conditions- (Minus -35?~60?, 0~95% RHG |
| 775 | POWER SUPPLY-DC 12 V ±25%, POE |
| 776 | POWER Consumption-Max. 5W(ICR Instant Switch 8.5W) |
| 777 | IR LIGHT- 2 |
| 778 | IR DISTANCE- 50Mtr. |
| 779 | CERTIFICATION:- BIS, ULC, FCC, CE & CMMI |
| 780 | Impact Protection - IP67, Lighting Protection, Surge Protection and Voltage transient Protection meets EN: 55035:2017 |
| 781 | IMPACT PROTECTION- IP67 |
| 782 | Supply, installation, testing and commisioning of 16 ChannelNVR (MAKE:-PELCO/ MILESTONE/ /HONEYWELL/ HYUNDAI) ), with 2 SATA port & 2 USB Port Simultaneous live monitoring, recording, playback, backup and remote access, video recording Continuous, schedule, manual, alarm triggered; Protection of recordings upto 30days, backup External storage device via USB; PC or network drive via LAN,video out put HDMI, VGA (D-Sub),supply voltage 230 VACi/c 2 Nos 4000GB (4 TB)Hard disc ( Western Digital - Make & Model-Survelliance Purpple) complete in all respect including making necessary connections & other petty material etc. |
| 783 | S/I/T/C of 24 PORT SWITCH Fully L3 Core W 10G SFPwith all labour & petty material reqd. to complete in all respectupto the entire satisfaction of Engineer-in-Charge (MAKE : WESTERN/DLINK/ CISCO/TEJAS) |
| 784 | S/I/T/C of 8-Port PoE Switch Layer 2 - Rack Mountable PoE Gigabit Ethernet standalone chassis, provides 8 RJ-45 10/100/1000 BaseT, 2 SFP/RJ-45 10/100/1000 BaseT or 100/1000 BaseX combo with AC power supply, option for stacking module, communication of the cameras to the NVR with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in Charge of the work. (MAKE : WESTERN/DLINK/ CISCO/TEJAS) |
| 785 | S/E of 24 U WALL MOUNT RACK of size (600mm W x 1000mm D) with front of glass, Fan,PDU, & Wheel for amplifier & PAsystem complete with all labour and petty material required. (Rtech-Make & Model-24U or equilent) |
| 786 | S/I/T/C OF 9U WALL MOUNT RACK 400mm deep with front glass doorconsisting of power distribution5 AMP sockets., mounting hardware , Cable manager etc. with all labour & petty material reqd. to complete in all respectupto the entire satisfaction of Engineer-in-Charge. (MAKE :DLINK/DYNAMIC /VPRO /CCI) |
| 787 | Supply and erection of 6 U Wall mounted rack of size (550mmX450mmX347mm) made of CRCA Sheet with powder coated |
| 788 | S/I/T/Cof outdoor type 4" x 4" box for CCTV should be Dust and Water Proof with all labour & petty material reqd. to complete in all respectupto the entire satisfaction of Engineer-in-Charge. (MAKE : STRONGER/SYNTEX/ VPRO) |
| 789 | Supply and erection of PC for CCTV system with cpu and wireless mouse & keybord. |
| 790 | S/E of 12"" MS Pipe bracket duly powder coated for camera mounting complete with all labour and petty material required. |
| 791 | Supply and erection of 43” ultra HD LEDsmart TV (Samsung – Makeor equivalent model ofSony/Pansonic/LG orequivalent in approved HPHC make list)complete in all respect including making necessary connections etc but w/o cost of TV Cable & Set up box & disc. |
| 792 | Supply and erection of 55” ultra HD LEDsmart TV (Samsung – Makeor equivalent model ofSony/Pansonic/LG orequivalent in approved HPHC make list)complete in all respect including making necessary connections etc but w/o cost of TV Cable & Set up box & disc. |
| 793 | SITC of 65” LEDTVwith webOS 4.0, Commercial Smart Home (Launcher Bar), Web Browser, Pre-loaded App (YouTube Only), Soft AP, Wi-Fi (ac), Screen Share (Miracast), DIAL, Bluetooth Audio Playback, LG Sound Sync/bluetooth, Mobile Connection Overlay, Music Player, USB Cloning, WOL (Magic Packet Only), SNMP, Diagnostics, SI Compatible, HDMI-CEC (1.4), HTNG-CEC (1.4), IR Out, Multi IR Code, Auto Off/Sleep Timer, Smart Energy Saving, Motion Eye Care or Equivalent model of Samsung /Sony/LG) i/c erection complete with all labour & petty material required to complete the job. |
| 794 | SITC of Logic swivel mount suitable for 55" & 65" LED display or equivalent |
| 795 | S/I/T/Cof1KVA ONLINE UPS Single phase input & output with 10 minutesbackup alongwith reqd.nos. batteries of reputed make & suitable size rack with two years warranty i/cwith all labour & petty material reqd. to complete in all respectupto the entire satisfaction of Engineer-in-Charge.(MAKE : APC & Model- SRC1KI-IN or equivallent model in LUMINIOUS/MICROTEK) |
| 796 | S/I/T/Cof3KVA ONLINE UPS Single phase input & output with 60 minutes (1 Hour) backup alongwith reqd.nos. batteries of reputed make & suitable size rack with two years warranty i/cwith all labour & petty material reqd. to complete in all respectupto the entire satisfaction of Engineer-in-Charge.(MAKE : APC & Model- SRC3KUXI or equivallent model in LUMINIOUS/MICROTEK) |
| 797 | S/I/T/C of Central Conference control Unit for Chairman unit & Delegate units working at 240 Volts AC having two microphone inputs as per the specifications, complete as required .( BXB - Make & Model - EDC - 1051 or equivalent model of Beyerdynamic, AKG ) |
| 798 | S/I/T/C of Flush Mount Chairman Audio Conference microphone system complete with ring LED press to talk button and priority Switch complete as required ( BXB - Make & Model - EDC - 1025 or equivalent model of Beyerdynamic, AKG ) |
| 799 | S/I/T/C of Flush Mount Delegate Audio Conference microphone unit complete with ring LED press to talk button complete as required ( BXB - Make & Model - EDC - 1024 or equivalent model of Beyerdynamic, AKG ) |
| 800 | SITC Of DLP Projector 4500 ANSI Lumens, Ressolution1920 X 1200, Contrast Ratio 15000:1 with remote control ( Vivitek - Make & Model - DX 831 ) or equiplent approved model |
| 801 | S/E of 2.50 Feet Long Mounting Bracket for Projector complete in all respect |
| 802 | S/I/T/C of Cabinet Loudspeaker 30 Watt, ABS enclosure U- bracket mounting, fixed with 2 Mtr twin core connection cable water & dust protected IP65, charcoal RAL 7021 complete with all other petty material required to complete the job in all respect upto the entire satisfaction of Engineer - In- Charge of work( Bosch - Make & Model - LB2-UC30-D1) any other equilent model of approved brand) |
| 803 | S/I/T/C of 120" Diagonal 4:3 aspect ratio Motorised screen Matte white surface, Wall or Ceiling mounted includes high voltage LVC with remote controlcomplete with all other petty material required to complete the job in all respect upto the entire satisfaction of Engineer - In- Charge of work.( AV space - Make & Model - 120 ) or any other equilent model of approved brand) |
| 804 | S/I/T/C of Cable Cubby for VGA & Audio and Power cabels as per the specifications, complete as required . |
| 805 | S/I/T/C of Equipment Rack with Provision for housing all control equipment with front & rear door and proper locking arrangements as per the specifications, complete as required. |
| 806 | S/I/T/CofMicrophone cable with connectors completein all respect i/c labour & other petty material required to complete the job. |
| 807 | S/I/T/C ofProfessional Quality Audio Amplifier with dual channelof 70 v line facility,200 + 200 watt RMS power each channel at 4 ohm as per the specifications, complete as required . |
| 808 | S/I/T/C of Speaker cable with connectors complete in all respect with all labour & petty material required. |
| 809 | S/I/T/C of 7 core shielded RGBHV cablewith connectors complete in all respect with all labour & petty material required. |
| 810 | Supply and erection of VGA/HDMI Cable i/c connectors ( Falcon / Beldon - Make ) for NVR/Switcher/LED Monitor in existing PVC conduit pipe complete in all respect including making necessary connections etc. |
| 811 | S/I/T/C of Audio-Video 15U Equipment rack with provision for housing all control euipment with front perforated door and Wheels etc. with proper locking arrangements , Fan & Power strip as per the specificatios, complete as required ( Make -Valrack orequivallent in Rittal,President) |
| 812 | Supply installation, testing and commissioning of EPBAX machine configured for 4 P&T Line and 16 extensions for intercom System (Make- Copper Connection & Model- 416 or equivalent in Panasonic) complete with other petty material reqd. |
| 813 | Supply and erection ofMDF 50 Pair distribution boxfor termination of telephones wires with necessary arrangement hinged doorfor locking arrangement complete in all respect with all labour and material required including making necessary connection . |
| 814 | Supply and erection of Caller ID Telephone instrument with digital display (Make-Beetel-M-53 or equivalent in Panasonic ) including making necessary connection . |
| 815 | Supply and erection ofTelephone instrument with digital display but without Caller ID (Make-Beetel-B-25 /C-11 or equivalent in Panasonic ) including making necessary connection . |
| 816 | Supply and laying 20 pair telephone copper conductor 0.51 mm brightannealedjelly shielded cable in existing pipe/ channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer- in - Charge of the work. |
| 817 | Supply, erection, testing and commissioning of 13 passengers (G+1) Electrical Traction Elevator Roomless , Gearless with With Speed of 1.0mtr/Second serving 6 Stops & 6 Opening with SS hairline finish, hand rail, Front Mirror, Vision Ponel with Glass & Grill of min. size 550 mm Height x 150 wide with protection grill on each door, Granite Flooring & ERD system complete as per latest guideliness of Chief Electrical Inspectorate Haryana be erected in accordance with the following Technical Specification and as per latest IS Specification. |
| 818 | (i)Make of Lift:- OTIS / KONE / MITSUBISHI/ SCHINDLER/ORBIS |
| 819 | ii)Type & capacity : Passanger ElevatorApp. 884 Kg. 13 person |
| 820 | iii) Speed mps :1.0 mtr per second |
| 821 | iv) Travelling (max) in mtrs :Aprrox. 5 mtrs |
| 822 | v)Serving : (G+1) 2 stops, 2 opening all opening on same side) |
| 823 | vi) Power Supply: 415 V, 3 phase,50 HZA C supply. |
| 824 | vii) Control : High performance simplex full collective control with or without atendant. |
| 825 | viii) Operation:Automatic |
| 826 | ix ) Motor:Permanent Magnet Synchronous ElectricTractionGearless Motor to be hoisted on guide rail within the elevator hoistway. . |
| 827 | x) Location of Motor: Motor to be hoisted above the rail within the elevator hoist way. |
| 828 | xi) Type of Drive : A. C . Variable Voltage Variable frequency with 16 Bit Microprocessor |
| 829 | xii) Car Size:1600 mm wide x 1400 mm deep (2.24 sq.meter) or as per manufacturer design. |
| 830 | xiii) Hoist way available: 2016 mm Widex 3000 mm Deep |
| 831 | xiv) Car Enclosure: Bright Annealed Scratch ResistanceSatainless Steel Panel. |
| 832 | xv) False Ceiling:Stainless steel false ceiling in hair line finish |
| 833 | xvi) Car Panel :stainless steel (scratch free) Hair line finish |
| 834 | xvii) Flooring :- G, 1, 2, 3, 4, 5 ( Granite Flooring ) |
| 835 | xviii) Clear Opening of door:900 mm wide x 2000 mm high |
| 836 | xix)Door Operation : Automatic DC/AC with adjustable Door Opening andclosing timings with center openingsliding door |
| 837 | xx) Door Frame : Stainless steel inhair line finish |
| 838 | xxi) Vision Ponel with Glass & Grill of size min. size 550 mm Height x 150 mm wide with protection grill on each door |
| 839 | xxii) ERD system complete as per latest guideliness of Chief Electrical Inspectorate Haryana |
| 840 | Other Features: |
| 841 | i)Battery operated intercom,emergency alarm and emergency light with maintance free rechargeable battery. |
| 842 | ii) Adjustable guide shoes.(Ensures good ride comfort) |
| 843 | iii) Digital direcion & position indicator in Car & at all landings. |
| 844 | iv) Integral full height car opening panelwith luminous combined with direction arrows, overload warning indicatorand services cabinet |
| 845 | v) Hands free press and speak intercom with EPABX for three way communication. |
| 846 | vi) Automatic rescue device with Manual rescue Lever (to rescue the Passanger in case of emergency) the device willbring the elevators to the nearest floor and open the door automatically in Case of power / phase failure / low voltage. |
| 847 | vii) Full height infrared safety curtain( Highly sensitive safety device for safe entrance & exit of thePassanger into the Car & automatic floor announcer. |
| 848 | viii) Diffused lighting in car. |
| 849 | ix) Cross floow fans=2 Nos. |
| 850 | x) Looking mirror inside of lift car. |
| 851 | xi) Face plate Finish: stainless steel in hair line. |
| 852 | xii) Face plate :Rectangular. |
| 853 | xiii) A three feet high railing shall be provided on car top |
| 854 | xiv) The motor shall be high starting torque and low starting current and shall be arrangedfor self lubrication. |
| 855 | xv) Proper weight screen shall be provided at the hoistway. |
| 856 | xvi) Fire retardant compound coated traveling cable shall be used. |
| 857 | xvi) 2 Phase Device Fire Man Drive& Fireman switch at ground floor |
| 858 | xvii) Micro Movements L.E.D. based Buttons . |
| 859 | xviii)Load Weighing device with overload bypass feature.(Audio Visual over load indicator in the car) |
| 860 | xix)Steel items such as Door Frames Sill Angles, Fascia Plates, Spring Buffers. |
| 861 | xx) Braille fixtures, Lift announcement system, Pit ladder, Hand rail , Pressure sensing device & Additional Car Gate Lock . |
| 862 | xxi) Three Side Hand Rails in Stainless Steel Finish |
| 863 | xxii) System Capable of withstanding +10% to –10% Variation in Supply Voltage Fluctuations. ( C.V.T should be provided for Protection of lift against Single phase, Low voltage & over voltage) |
| 864 | xxiii) Car Platform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel |
| 865 | xxiv) Fire Rated Landing Doors for a Period of One Hour Only. |
| 866 | xxv) The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice and vibration. |
| 867 | xxvi) A handrail not less than 0.60mtr long and 1.0 mtr. Above floor level shall be fixed adjacent to the control panel.. |
| 868 | xxvii) The time of automattically closing door shall be minimum 5 seconds and the closing speed shall not exceed 0.25mtr./ Seconds |
| 869 | xxviii) Overspeed governor ( Electro-mechanical device that prevents free fall in case the lift is travelling at speed more than 10% of the rated speed in downward direction. |
| 870 | xxix) All other required features relates the operation of lift by the Handicapts & Blind person as per instruction of lift inspector. |
| 871 | Note :-No objection Certificate for the Lift will be taken by the agency concern departmentand necessary fee for the same if any will also be born by the agency. |
| 872 | Total NS Amount |
| 873 | Estate Electrical NS Item |
| 874 | Supply , Installation, testing and commissioning of 62.5 KVA water cooled , silent diesel Generating set complete with alternator rated at three phase 415 volts, 50 cycle, 0.8 PF & 1500 RPM with AMF Panel (outside/inside the canopy), Acoustic Enclosure and battery charger etc.( To be installed out door on existing platform excluding cost of platform ) as per following specifications: - |
| 875 | A. DIESEL ENGINE : Engine multi cylinder,developing output as per 62.5 KVA DG Set at 1500 RPM, Vertical, totally enclosed, water cooled, comprising compression ignition, electric start, 4 stroke high speed diesel engine conforming to IS - 4722 , ISO - 3046, BS - 5514. The engine shall be complete with all standard and electrical accessories as per standard supply of manufactures. The engine shall be coupled with 3 phase 415 volts, 50 cycle, 0.8 PF & 1500 RPM, alternator as per IS - 4722 / BIS - 2613, rated for 24 hours of continuous operation with 10 % over load capacity for one hour in every 12 hours and comprising witha) AMF Panel of required size complete with all accessories as required , IP-53 protection as per IS /IEC :60947(Part-I) / 2007 b) ON / OFF start keys c) Lube oil pressure gauge d) Fuel Tank with capacityfor 8 hours continuous running at full load e) Residential Silencer of required size and length i/c all necessary material as required. |
| 876 | f) 1 No, 12 Volts, 150 AH, DC Mtr. Free batteries with leads & container. g) AVM Pads fitted on base frame h) The base frame would be fabricated from suitable M.S. Channels suitable machined to perfect alignment of the engine and alternator with rigid construction and necessary reinforcement to ensure minimum vibration. (i) AC Digitalvolts and Amperes metres with selector switch of class 1.5 accuracy (j) 4 pole MCCB of suitable capacity on output of DG set (k) 4 pole MCCB of 100 Ampcapacity on output and input side of AMF panel (l) 4 pole Contractors of suitable capacity in AMF Panel (m) Pilot lamps 3 nos. (n) 5 nos. Indicating lamps to indicate main low voltage , load on mains , DG set running , load on set and battery charger ON (o) Under voltage relay for mains (p) Over voltage protection (q) Any other accessories to make the generating set functional shall be installed as per manufacturer"s specification. |
| 877 | (B) BATTERY CHARGER: The battery charger with volt metre and Ammeter shall be installed of required size and rating for charging of battery from mains. This will be in addition to the battery charging alternator fitted on the engine. ( C ) ACCOUSTIC ENCLOSURE : Acoustic enclosure shall be provided as per Technical specification as follows :- 1) CONSTRUCTION & PAINTING : i) The enclosure shall be fabricated out of 16 SWG CRCA sheet silent D.G. set container shall be of modular construction with the provision to assemble and dismantle easily at site of work. ii) The base fame shall be made of ISMC of suitable section. iii) Durable industrial system is to be provided on the doors and doors are fitted with high quality EPDM gasket to avoid leakage of sound. iv) Weather proof anti corrosion treatment to be provided to the entire structure with powder coating. v) Neutral/Body earthing points at the side of enclosure are to be provided vi) Emergency stop push button shall be provided outside the container. vii) A tube fitting with tube rod for proper light inside the canopy shall be provided. |
| 878 | D.) ACCOUSTIC INSULATION : i) Sound proofing of the enclosure shall be done with quality rock wood/Mineral wood conforming to IS-8183-1993 of 25mm thickness and density at 30 Kg./M compressed along with 3mm thick vinyl sheet and non ferrous sheet. ii) Exhaust pipe is to be thoroughly insulated by covering it with glass wool and further claded with Aluminium sheet. iii) 75 db A noise level as per Central Pollution Control Board (CPCB) -II with latest amanedments Note Any other material required to complete the Acoustic Enclosure shall be installed as per manufacturer"s specifications. |
| 879 | S/I/T/C of250 KVA, 11 /0.43 KV, 50 HZ , Copper wound, oil immersed , Naturally Cooled outdoor type distribution transformer conforming to IS-1180 (Part-I) 2014as per LatestEnergy Efficiency Level-IIas per following specificationsStack Core type construction, CRGO core, Vector Group DYN-11,Tappings +5% to -10%off Load Tap Changer with H.T/L.T Cable boxes and all fittings & accessories reqd. to be installed on reqd size existing plateform or on H-Pole Structure to complete the job in all respect upto the entire satisfaction ofE- I - C of work. |
| 880 | Supply, erection, testing and commissioning of 11 KV HT Single VCB Panel (one incoming & one outgoing.) 12KV 630 Amp. 350 MVA comprising of four nos. TGA-2V type load break SF6 insulated switches suitable for indoor installation and as per following specification:- Rated Voltage:12 KV , Rated current: 630 Amp. Short time current: 20KA for 1 sec. Incoming Panel includes:- Operating mechanism with manual operation Bus Bar system 12 KV-630 A Quick make and Break with ON ,OFF position VoltagepresenceindicatingLamps, inbuilt powerback Each outgoing Panel includes: Operating mechanism with manual operation Door interlock ,Earthing Switch Bus Bar system 12 KV-630A QuickmakeandBreakwithON ,OFFposition 1 No.Thermostat Controlledanti-condensationspace heater 1 Setof phaseindicatingLamps 1 SetON/OFFindicatingLamps 1 SetLVControl MCB"s Automatic trippingin case of anyfuseblow up 11KVHT HRC Fuses( 01 set). |
| 881 | Supply and erection of HT Modem of approved makefor sending message of meter reading automatically to the office of UHBVN/DHBVN complete in all respects including making necessary connection etc. |
| 882 | Supplying , fixing , testing and commissioning of out-door type (IP 66) Feeder Pillar made out of 2mm thick CRCA sheet steel encloser duly painted with powder coatedpaint the top cover will be extended by at least 150 mm slope to drain out rain water. The feeder Pillar shall be covered on break masonry pedestal with proper cavity in middle for cable entry with 25x3 mm earthing bus from end to end .( Ratesinclude cost of pedestal of reqd. size & All components as per approved make of HPHC List) |
| 883 | Incoming |
| 884 | 1 No. 100 Amps, FP MCCB,(25KA) with rotary handle |
| 885 | 1 No.70 Amps, FP contactor with auxiliary contacts, overload protection, under voltage coil.The contactor to be controlled by Timer through an Auto/Manual Selector switch. |
| 886 | Outgoing |
| 887 | 2 Nos 63 Amps, 4P MCB, 415 volts, 3 phase, 50 Hz. |
| 888 | 1 Nos 40 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 889 | 3 Nos 32 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 890 | 4 Nos 16 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 891 | 2 Nos 25 Amps, DP MCB, 230 volts, 1 phase, 50 Hz. |
| 892 | Bus bar |
| 893 | 1 set 150 Amps, 415 volts, 3 phase 4 wire colour coded copper bus bars. |
| 894 | 1 set 100 Amps, 415 volts, 3 phase 4 wire colour coded copper bus bars. |
| 895 | Instruments |
| 896 | 1 No 0-500 Volts, Digital voltmeter with built in selector switch and protection fuses. |
| 897 | 1 No 0-100 Amps, Digital ammeter with built in selector switch and matching CT"s . |
| 898 | 1 Set of RYB phase indicating lamps (LED). |
| 899 | S/I/T/Cof L.TPanel-1 out-door type made out of 2mm thick CRCA sheet steel encloser duly painted with Powder Coated Siemens Grey paint and the top cover will be extended by at least 150 mm slope to drain out rain water complete with RYB phase indicating LED lamps,0-500 Volts, Digital voltmeter with built in selector switch,0-100 Amps, Digital ammeter with built in selector switch and matching CT"s,RED/GREEN/AMBER lights for indicating ON/OFF/TRIP , Control wiring & mcb"s,TPN 500A electrolytic grade Aluminium bus-bar with colour coded heat shrinkable PVC sleeves, end to end 25x3 mm earthing, reqd. hardware, base channel 75x40 mm and as per following specifications:- |
| 900 | Incoming |
| 901 | 1 No. 500 Amps, FP MCCB (50 KA) Thermal released with O/L,S/C & E/F protection and Rotary operating mechanism. |
| 902 | Outgoing |
| 903 | 5 Nos 160 Amps, 4P MCCB(25 KA) thermal magnetic type withrotary handle. |
| 904 | 2 Nos 100 Amps, 4P MCCB (25 KA) thermal magnetic type withrotary handle. |
| 905 | 2 Nos 63 Amps, 4P MCCB (25 KA) thermal magnetic type withrotary handle. |
| 906 | 1 Nos 63 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 907 | 2 Nos 32 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 908 | APFC 80KVAR Capacitor Bank as per details |
| 909 | 1).1 Nos 160 Amps, TP MCCB(25 KA) thermal magnetic type withrotary handle as incommer. Automatic power factor controller 6 stage relay & Automatic selector switch 1-pole 2way. |
| 910 | 2). 25Kvar x 2nos. Capacitor Banks with 32A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 911 | 3). 15Kvar x 1no. Capacitor Banks with 32A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 912 | 4). 10Kvar x 1no. Capacitor Banks with 25A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 913 | 5). 5Kvar x 1no. Capacitor Banks with 16A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 914 | S/I/T/Cof L.TPanel-2 out-door type made out of 2mm thick CRCA sheet steel encloser duly painted with Powder Coated Siemens Grey paint and the top cover will be extended by at least 150 mm slope to drain out rain water complete with RYB phase indicating LED lamps,0-500 Volts, Digital voltmeter with built in selector switch,0-100 Amps, Digital ammeter with built in selector switch and matching CT"s,RED/GREEN/AMBER lights for indicating ON/OFF/TRIP , Control wiring & mcb"s,TPN 500A electrolytic grade Aluminium bus-bar with colour coded heat shrinkable PVC sleeves, end to end 25x3 mm earthing, reqd. hardware, base channel 75x40 mm and as per following specifications:- |
| 915 | Incoming |
| 916 | 1 No. 500 Amps, FP MCCB (50 KA) Thermal released with O/L,S/C & E/F protection and Rotary operating mechanism. |
| 917 | Outgoing |
| 918 | 2 Nos 160 Amps, 4P MCCB(25 KA) thermal magnetic type withrotary handle. |
| 919 | 4 Nos 100 Amps, 4P MCCB (25 KA) thermal magnetic type withrotary handle. |
| 920 | 3 Nos 63 Amps, 4P MCCB (25 KA) thermal magnetic type withrotary handle. |
| 921 | 1 Nos 63 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 922 | 2 Nos 32 Amps, TPN MCB, 415 volts, 3 phase, 50 Hz. |
| 923 | APFC 80KVAR Capacitor Bank as per details |
| 924 | 1).1 Nos 160 Amps, TP MCCB (25 KA) thermal magnetic type withrotary handle as incommer. Automatic power factor controller 6 stage relay & Automatic selector switch 1-pole 2way. |
| 925 | 2). 25Kvar x 2nos. Capacitor Banks with 32A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 926 | 3). 15Kvar x 1no. Capacitor Banks with 32A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 927 | 4). 10Kvar x 1no. Capacitor Banks with 25A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 928 | 5). 5Kvar x 1no. Capacitor Banks with 16A TP MCB, Contactor,Relay, Start/Stop push buttons,Indication lamps etc. |
| 929 | S/E of 200 watt LED Flood Light luminairewith IP-66 Protection and made in pressure die cast and heat shrink aluminium extrusion with high power LEDs as light sourceto be mount on existing building/ terrace complete in all respect.suitable for operation on 230 volts A.C supply . |
| 930 | S/E of 60 watt LED Flood Light pressure die casthousingwith IP-65 Protection and efficient LED output for better distribution to be mount on existing building/ terrace complete in all respect.suitable for operation on 230 volts A.C supply. |
| 931 | Supply,installation, testing and commissioning of 72 W LED Street Light luminaire housing shall be of corrosion free, cast aluminium spigot, comprising of acrylic diffuser, LED chips, mounted on suitable designed aluminium heat sink with high thermal conductivity for better heat dissipation, fitted with integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket lining complying to IP 65 class of protection i/c necessary connections as required . |
| 932 | S/E of 1.0 Mtr , 48 mm dia hot dip galvenized bracket for fixing on the existingHot Dip Galvanized octagonal pole 7/8 meter height, complete with aluminium dome on top of bracket, labour and petty material required to complete the job in all respect upto the entire satisfaction Engineer in charge of the work. |
| 933 | (i) Single Arm |
| 934 | ii) Double Arms |
| 935 | S/E of 1.5 mm sqmm x 3 core PVC insulated multi core copper conductor cable (unarmoured) 1100 volts grade (round) in existing pole/ pipe, complete in all respect including making necessary connections. |
| 936 | S/E of 2.5 mm sqmm x 3 core PVC insulated multi core copper conductor cable (unarmoured) 1100 volts grade (round) in existing pole/ pipe, complete in all respect including making necessary connections. |
| 937 | S/E 3 phase automatic street light controller (Digital) with timer switch operation ON& OFF setting for 24 hours for each phase complete with 63 amp contactor & MS powder coated enclosure of suitable size to complete the job with all labour and petty material required. |
| 938 | S/E of fire buckets of 9 liters capacity made out of 24 gauge GI sheet& duly painted with one coat of red oxide and two coat of approved paint in red colour written with fire as per fire protection complete with necessary sand filling in the bucket and labour etc. |
| 939 | S/E of fire existingusher ISI marked C02 type of 6.8 kg capacity as per IS:7285 duly erected/hangs on wall with hooks i/c the cost of hook, screws etc with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer in charge of the work. |
| 940 | S/E of fire existingushers ISI markeddry chemical powder type of 4 KG capacity as per IS duly erected/hangs on wall with hooks i/c the cost of hook, screws etc with all labour and material required to complete the job in all respect to the entire satisfaction of the Engineer- in - Charge of the work. |
| 941 | S/E of cross arm channal of size 75 mm x 40 mm for laying of earth wire, ACSR conductor & other purposes, fixing with U type clamps made out of M.S. flat of size 50mmx 6mm, nuts & bolts, on the existing pole complete in all respect including painting, labour and other petty material required to complete the job in all respect upto the entire satisfaction of the Engineer in charge of work. |
| 942 | Supply of aluminum Til-table Tower Extension Ladder adjustable at any desired working height and platform in 2 folds model made out of heavy duty Aluminum “C” Section of Size 66mm x 31mm x 3mm approx. thick & rungs made out of 25 mm dia, complete in all respect .Size: Working height – 36 feet.Close Height – 20 feet, Extended Height -36feet (Model 2512 of Relads of Radium or Model SKL-116 of SK Ladders make). |
| 943 | Supply of 11KV XLPE (E) insulated and sheathed aluminium conductor armoured cables ISI marked in existing pipe or trenches complete with necessary connections including loading unloading & carriage but excluding cost of Cable end boxes on both sides as required of following sizes. |
| 944 | i.) 70 sq.mm. 3 Core Al. Armoured (E) |
| 945 | ii.) 120 sq.mm. 3 CoreAl. Armoured (E) |
| 946 | Total Estate NS Amount |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
