Upgradation Of Bakbaki Hsc Under R.D. Kalacherra Sub Division During The Year 2022-23 ( Composite Work ) . Maintenance Work
Tender Value
16.25 Lakhs
Estimated cost
Bid Submission
07 Jun 2022
0 days left
EMD
32505
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
North Tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Upgradation Of Bakbaki Hsc Under R.D. Kalacherra Sub Division During The Year 2022-23 ( Composite Work ) . Maintenance Work
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulicexcavator) / manual means in foundation trenches ordrains (not exceeding 1.5 m in width or 10 sqm on plan)including dressing of sides and ramming of bottoms, liftupto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a leadof 50 m.-All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) intrenches, plinth, sides of foundations etc. in layers notexceeding 20cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and liftupto 1.5 m.-All kinds of soil |
| 3 | Excavating, supplying and filling of local earth (includingroyalty) by mechanical transport upto a lead of 5 km alsoincluding ramming and watering of the earth in layers notexceeding 20 cm in trenches, plinth, sides of foundationetc. complete. |
| 4 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts includingspreading in horizontal layers, watering, grading torequired slope, ramming, consolidating and compactingeach layer by using plate compactor or by any suitablemethod complete |
| 5 | Providing and laying in position cement concrete ofspecified grade excluding the cost of centring andshuttering --All work upto plinth level:4.1.7 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stoneaggregate 40 mm nominal size) |
| 6 | Providing and laying in position cement concrete ofspecified grade excluding the cost of centring andshuttering --All work upto plinth level:4.1.5 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stoneaggregate 20 mm nominal size) |
| 7 | Making plinth protection 50mm thick of cementconcrete 1:3:6 (1 cement : 3 fine sand : 6 graded wellburnt brick aggregate 20 mm nominal size) over75mm bed of dry brick ballast 40mm nominal sizewell rammed and consolidated and grouted with finesand including finishing the top smooth |
| 8 | Centering shuttering including struttings, propping etc.and removal of form work for:5.8.1.1 Foundations, footings, bases for columns etc. for massconcrete with timber plank |
| 9 | 5.8.4.2 Suspended floors, roofs, landings, balconies and accessplatform with 12 mm thick shuttering ply |
| 10 | 5.8.5.1 Lintels, beams, plinth beams, girders, bressumers andcantilevers with shuttering ply |
| 11 | 5.8.6.1 Columns, Pillars, Piers, Abutments, Posts and Struts withshuttering ply |
| 12 | Providing and laying in position specified grade ofreinforced cement concrete excluding the cost ofcentring, shuttering, finishing and reinforcement--All work upto plinth level:5.1.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stoneaggregate 20 mm nominal size) |
| 13 | Reinforced cement concrete work in beams, suspendedfloors, roofs having slope upto 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases upto floor five levelexcluding the cost of centring, shuttering, finishingand reinforcement 5.3.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stoneaggregate 20 mm nominal size) |
| 14 | Reinforced cement concrete work in walls (anythickness), including attached pilasters, buttresses,plinth and skirting courses, fillets, columns, pillars,piers, abutments, posts and struts etc. upto floor fivelevel excluding cost of centring, shuttering, finishingand reinforcement 5.2.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stoneaggregate 20 mm nominal size) |
| 15 | 5.18 Providing precast cement concrete Jali 1:2:4 (1 cement:2 coarse sand : 4 graded stone aggregate 6mm nominalsize) reinforced with 1.6 mm dia mild steel wireincluding centring and shuttering, rougheningcleaning, fixing and finishing in cement mortar1:3(1cement : 3 fine sand) etc. complete, excluding theplastering of jambs, sills and soffits5.18.3 25 mm thick |
| 16 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding allcomplete upto plinth level.5.19.4 Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 17 | First class brick work in foundation and plinthincluding cost of all materials as required complete:-6.1.5 In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 18 | Half brick masonry work with first class bricks infoundation and plinth including cost of all materials asrequired complete:-6.10.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 19 | First class brick work in superstructure above plinthlevel & upto floor-five level including cost of allmaterials as required complete:-6.3.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 20 | Half brick masonry work with first class bricks insuperstructure upto floor five level including cost ofall materials as required complete:-6.12.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 21 | Providing and fixing stainless steel (Grade 304) railingmade of Hollow tubes, channels, plates etc., includingwelding, grinding, buffing, polishing and makingcurvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete,including fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., ofrequired size, on the top of the floor or the side of waistslab with suitable arrangement as per approval ofEngineer-in-charge, (for payment purpose only weight ofstainless steel members shall be considered excludingfixing accessories such as nuts, bolts, fasteners etc.). |
| 22 | Providing and laying cement concrete 1:2:4 (1 cement: 2fine sand : 4 graded well burnt brick aggregate) flooringfinished with a floating coat of neat cement includingcement slurry, rounding of edges and strips and cost ofglass strips etc. complete.10.6.1 40mm thick. |
| 23 | Providing and laying 40 mm thick marble chips flooringrubbed and polished to granolithic finish, under layer 34mm thick cement concrete 1 : 2 : 4 ( 1 ordinary cement :2 fine sand : 4 graded stone aggregate 12.5 mm nominalsize ) and top layer 6 mm thick with white, black,chocolate, grey, yellow, pink, blue or green marble chipsof sizes from 1 mm to 4 mm nominal size laid in cementmarble powder mix 3 : 1 ( 3 cement : 1 marble powder )by weight in proportion of 4 : 7 ( 4 cement marblepowder mix : 7 marble chips ) by volume includingcement slurry etc. complete.10.14.1 Dark shade pigment with ordinary cement |
| 24 | Providing and fixing 1st quality ceramic glazed wall tiles(minimum 200 x 300) conforming to IS : 15622 - 2017(thickness to be specified by the manufacturer) ofapproved make in all colours, shades of any size asapproved by Engineer-in-charge in skirting, risers ofsteps and dados, laid over 12 mm thick bed of cementmortar 1 : 3 (1 cement : 3 fine sand) jointed withordinary cement slurry including pointing with whitecement mixed with pigment of matching shade complete. |
| 25 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622 - 2017, of approved make, in all colours andshades, laid over 20mm thick cement mortar 1:4 (1cement : 4 fine sand), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joints with whitecement and matching pigments etc., complete10.42.2 Double charged Stainfree vitrified tiles10.42.2.1 Size of tile 60x60 cm |
| 26 | Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded builtup standard tubular sections/ appropriate Z sectionsand other sections of approved make conforming toIS: 733 and IS : 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up ofgaps at junctions, i.e. at top, bottom and sides withrequired EPDM rubber/neoprene gasket etc. Aluminiumsections shall be smooth, rust free, straight, mitred andjointed mechanically wherever required including cleatangle, aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as perarchitectural drawing and the direction ofEngineerincharge. (Glazing and paneling and dashfasteners to be paid for separately) :-16.1.1 For fixed portion of approved quality:-16.1.1.1 Anodised aluminium (anodised transparent or dyed torequired shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 27 | Providing and fixing glazing of approved quality inaluminium doors, windows, ventilator, shutters andpartition etc. with EPDM rubber / neoprene gasket etc.complete as per architectural drawing and the directionof Engineer-in-charge (Cost of snap beading shall be paidin basic item) :-16.3.1 With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 28 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wroughtframed and fixed in position :8.1.3 Local Teak Wood |
| 29 | Providing and fixing factory made UPVC door framemade of UPVC extruded, section having an overalldimension, as below (tolerance +/- 1mm) with wallthickness 2.0mm+/- 02mm. corners of the doorframe to be jointed with galvanized brackets andstainless screws, joint mitred and plastic wilded. Thehinge side vertical of the frames reinforced bygalvanized MS tube of size 19 × 19 mm and 1 mm +/-0.1 mm wall thickness and 3 nos stainless steelhinges fixed to the frame complete as permanufacturers specification and direction ofEngineer-In-Charge.8.114.1 Extruded section Profile size 48x40 mm. |
| 30 | Providing and fixing panelled / or panelled andglazed shutters for doors, windows and clerestorywindows including ISI marked bright finished /black enamelled M.S butt hinges with necessaryscrews excluding panelling and or glazing, whichwill be paid for separately but including the woodenbeading of 20 × 12 mm for fixing panelling and orglazing as per direction of Engineer-In-Charge.8.5.2 Gamair Wood8.5.2.1 35 mm thick shutters |
| 31 | 8.115.2 30mm thick factory made Polyvinyl Chloride (PVC)door shutter made of styles and rails of a UPVC profilesection of size 30mm x 60mm and wall thickness2mm ± 0.2mm with inbuilt decorative mouldingedging on one side. The styles and rails with plasticbrackets of size 75×220 mm mitred and welded at thecorners. The styles of the shutter reinforced byinserting galvanised MS tube of size 25×20 mm and 1mm ± 0.1 mm wall thickness. The lock rail made up of\"H\" Section, a UPVC profile section of size 30×100 mmand 2 mm ± 0.2 mm wall thickness welded to theshutter style with a UPVC profile section single panelof size not less than 620 mm, having overall thicknessof 20 mm and 1 mm ± 0.1 mm wall thickness with 20mm panel beading of suitable size/Glass (4 mm thickplain glass)/ louver section, louver frame of suitablesize, complete as per manufacturer\"s specification and direction of Engineer-In-Charge. (for W.C. andBathroom door shutter). |
| 32 | Providing and fixing bright finished brass towerbolts(barrel type)with necessary screws etc. complete :8.72.1 250 x 10 mm |
| 33 | Providing and fixing bright finished brass door latchwith necessary screws etc. complete :8.73.1 300x16x5 mm |
| 34 | Providing and fixing chromium plated brass handleswith necessary screws etc. complete:8.90.1 125 mm |
| 35 | 8.48 Providing and fixing hard drawn steel wire fabric 75x 25 mm mesh of weight not less than 7.75 Kg persqm to window frames etc. including 62 x 19 mmbeading of Gamair wood. |
| 36 | Providing and fixing M.S. grills of required pattern inframes of windows etc. with M.S. flats, square orround bars etc. all complete.8.46.2 Fixed to openings /wooden frames with rawl plugsscrews etc. |
| 37 | 12 mm cement plaster of mix12.1.4 Cement mortar 1:6 (1 cement : 6 fine sand) |
| 38 | 15 mm cement plaster on the rough side of single orhalf brick wall of mix:12.2.4 Cement mortar 1:6 (1 cement : 6 fine sand) |
| 39 | 6 mm cement plaster of mix :12.4.2 Cement mortar 1:4 (1 cement : 4 fine sand) |
| 40 | Neat cement punning |
| 41 | Finishing walls with textured exterior paint of requiredshade of approved brand and manufacture [Paymentshall be made after submission of Test Certificate issuedby the Manufacturer] :12.29.1 New work ( two or more coats applied @ 3.28 litre/10sqm) over and including priming coat of exterior primerapplied @ 2.20 kg/10 sqm |
| 42 | 12.32.2 Painting wood work with Deluxe Multi Surface Paint ofrequired shade. Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @ 0.75 ltr/10sqm of approved brand and manufacture. |
| 43 | 12.32.3 Painting Steel work with Deluxe Multi Surface Paint togive an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 44 | 17.14 Grading roof for water proofing treatment complete asrequired as per direction of the Engineer-in-charge with :17.14.2 Cement mortar 1:3 (1 cement : 3 fine sand) |
| 45 | Providing and fixing on wall face unplasticisedRigid PVC rain water pipes (working pressure 4kg/cm2) conforming to IS : 13592 Type A includingjointing with seal ring conforming to IS : 5382leaving 10 mm gap for thermal expansion:11.42.1 Single socketed pipe - 75 mm OD |
| 46 | Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type-Aincluding jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:11.43.1 Coupler11.43.1.1 75 mm |
| 47 | 11.43.4 Single equal tee with door11.43.4.1 75x75x75 mm |
| 48 | 11.43.6 Plain shoe11.43.6.1 75mm |
| 49 | Providing and fixing unplasticised -PVC pipe clips ofapproved design to unplasticised - PVC rain waterpipes by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required lengthincluding cutting brick work and fixing with cementmortar 1 : 4 (1cement : 4 fine sand) making good thewall etc. complete.11.44.1 75mm |
| 50 | Providing and fixing to the inlet mouth of rain waterpipe PTMT grating with thickness of 8mm and weighingnot less than 100gm. complete. 11.45.1 75mm |
| 51 | Extra for straight cutting in C.G.S. sheet roofing formaking opening of area exceeding 40 sq. decimeter forchimney stacks, sky light etc. :11.2.2 0.63mm thick |
| 52 | 11.25.4 Fully Perforated Gypsum Plaster Board of size 1200 x2400x12.5 mm having approx. 15 % perforated area withperforation size and pattern as approved by the Engineer incharge and as per manufacturer\"s specification, with all4 side tapered and backed by acoustical tissue with NRCvalue not less than 0.60. |
| 53 | Providing corrugated G.S. sheet roofing includingvertical/curved surface fixed with polymer coated Jor L hooks, bolts and nuts 8 mm diameter withbitumen and G.I. limpet washers or with G.I. limpetwashers filled with white lead and including a coatof approved steel primer and two coats of approvedpaint on overlapping of sheets complete (up to anypitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever required.11.1.2 0.63mm thick with zinc coating not less than 275gm/m2 |
| 54 | Repairs to plaster of thickness 12 mm to 20 mm inpatches of area 2.5 sqm and under including cutting thepatch in proper shape and preparing and plastering thesurface of the walls complete including disposal ofrubbish to the dumping ground with all leads and liftsincluding finishing even and smooth and curingcomplete as per direction of the Engineer in charge:-13.30.2 With cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 55 | Removing white or colour wash by scrapping and sandpapering and preparing the surface smooth includingnecessary repairs to scratches etc. complete |
| 56 | Distempering with oil bound washable distemper ofapproved brand and manufacture and of requiredshade on old work ( one or more coats ), to give aneven shade as required complete as per direction of theEngineer in charge. |
| 57 | 13.39 Finishing walls with textured exterior paint of requiredshade of approved brand and manufacture on old work( one or more coats ) including preparation of surfaceas required complete as per direction of the Engineer incharge |
| 58 | 14.22 Dismantling GS sheet roofing including ridges, hips,valleys, gutters wind ties etc. includingdismembering and stacking of serviceable materialsand unserviceable materials separately with all liftsand upto a lead of 50 m etc.complete as perdirection of the Engineer- in-charge. |
| 59 | 14.23 Dismantling old plaster or pointing, raking outjoints, cleaning and preparing the surface for re plastering or re-pointing including disposal ofrubbish to the dumping ground with all leads andlifts etc.complete as per direction of the Engineer- in charge. |
| 60 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps,32 mm C.P. brass waste ofstandard pattern, including painting of fittings andbrackets, cutting and making good the wallswherever require :18.7.1 White Vitreous China Wash basin size 630x450 mm with apair of 15 mm C.P. brass pillar taps |
| 61 | Providing and fixing white vitreous china water closetsquatting pan (Indian type)18.13.2 Orissa pattern W.C. pan of size 580x440 mm |
| 62 | Providing and fixing a pair of white vitreous china footrests of standard pattern for squatting pan water closet:18.17.1 250x130x30 mm |
| 63 | Providing and fixing white vitreous china laboratorysink with C.I. brackets, C.P. brass chain with rubberplug 40mm C.P brass waste and 40mm C.P. brass trapwith necessary C.P. brass unions complete includingpainting of fittings and brackets, cutting and makinggood the wall wherever required :18.11.1 Size 450x300x150mm |
| 64 | 18.29 Providing and fixing 100 mm sand cast Iron grating forgully trap. |
| 65 | Providing and fixing P.V.C. waste pipe for sink or washbasin including P.V.C. waste fittings complete18.28.2 Flexible pipe18.28.2.1 32 mm dia |
| 66 | 18.84.9 Double unequal junction of required degree without door18.84.9.1 110x110x75 x 75 mm |
| 67 | 18.84.10 Double unequal junction of required degree with door18.84.10.1 110x110x75 x 75 mm |
| 68 | 18.84.11 Single unequal junction of required degree without door18.84.11.1 110x110x75 mm |
| 69 | 18.84.12 Single unequal junction of required degree with door18.84.12.1 110x110x75 mm |
| 70 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water, soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete18.85.2 110mm |
| 71 | Providing and fixing on wall face unplasticised RigidPVC rain water, soil, waste & vent pipes (workingpressure 4 kg / cm2) conforming to IS : 13592 Type Aincluding jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:18.82.2 Single socketed pipe - 110 mm OD |
| 72 | Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water, soil, waste & vent pipes pipesconforming to IS : 13592 Type A including jointingwith seal ring conforming to IS : 5382 leaving 10 mmgap for thermal expansion:18.84.1 Coupler18.84.1.2 110 mm |
| 73 | 18.84.3 Single equal tee without door18.84.3.2 110x110x110mm |
| 74 | 18.84.4 Single equal tee with door18.84.4.2 110x110x110mm |
| 75 | 18.84.5 Bend 87.5°18.84.5.2 110mm |
| 76 | 18.84.7 Double equal junction of required degree without door18.84.7.2 110x110x110 x110 mm |
| 77 | 18.84.8 Double equal junction of required degree with door18.84.8.2 110x110x110 x110 mm |
| 78 | 18.84.6 Plain shoe18.84.6.2 110mm |
| 79 | Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stability forhot & cold water supply including all CPVC plain &brass threaded fittings including fixing the pipe withclamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction ofEngineer in Charge.Internal work - Exposed on wall19.7.1 15 mm nominal outer dia .Pipes |
| 80 | Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stability forhot & cold water supply including all CPVC plain &brass threaded fittings including fixing the pipe withclamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction ofEngineer in Charge.Internal work - Exposed on wall19.7.2 20 mm nominal outer dia .Pipes. |
| 81 | Providing and fixing brass bib cock of approvedquality :19.15.1 15 mm nominal bore |
| 82 | Providing and fixing brass stop cock of approvedquality :19.16.1 15 mm nominal bore |
| 83 | Providing and fixing C.P. brass angle valve for basinmixer and geyser points of approved qualityconforming to IS:893119.53.1 15 mm nominal bore |
| 84 | Providing and placing on terrace (at all floor levels)polyethylene water storage tank ISI : 12701 markedwith cover and suitable locking arrangement andmaking necessary holes for inlet, outlet and overflowpipes but without fittings and the base support fortank. |
| 85 | Providing and installation of 1.0 HP mono block along with starter including all accessories complete as per the direction of the Engineer-in-charge. (NON SCHEDULE) |
| 86 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated copper conductor cable (FR) in pvc casing and capping complete with PVC switch board and fancy type switch with cover plate including connection etc as required.Short Point :- |
| 87 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated copper conductor cable (FR) in pvc casing and capping complete with PVC switch board and fancy type switch with cover plate including connection etc as required. Medium Point :- |
| 88 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated copper conductor cable (FR) in pvc casing and capping complete with PVC switch board and fancy type switch with cover plate including connection etc as required.Long Point : |
| 89 | Providing and fixing of 3 pin 5/6 amps plug point with fancy type 5/6 amps switch and socket with cover plate including connection with 2x1.5 sq. mm PVC insulated Copper conductor cable (FR) on PVC switch board, earthing the 3rd pin etc. as required. |
| 90 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC casing capping etc. as required:-2 X 1.5 sq mm |
| 91 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC casing capping etc. as required:-2 X 2.5 sq mm |
| 92 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC casing capping etc. as required:-2 X 4 sq mm |
| 93 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC casing capping etc. as required:- 2 X 6 sq mm |
| 94 | Wiring for Circuit/Sub-main wiring with the following sizes of PVC insulated copper conductor cable (FR) in existing PVC casing capping/ conduit in recess/surface including connection etc. as required:-1 X 1.5 sq mm |
| 95 | Wiring for Circuit/Sub-main wiring with the following sizes of PVC insulated copper conductor cable (FR) in existing PVC casing capping/ conduit in recess/surface including connection etc. as required:- 1 X 2.5 sq mm |
| 96 | Supplying and fixing of MS frame made of (25 x 25 x 5)mm MS angle with necessary support by (40 x 6)mm MS flat and 10 mm thick boiled plywood on top, grouted on wall with 4 nos leg(25x25x5mm MS angle 20 cm long) finished with red oxide and 2 coat synthetic enamel paint including necessary cc work, mending the damages & painting etc as required:- |
| 97 | Supplying and fixing of the following switch disconnector fuse unit(main switch)made of sheet steel enclosure with all accessories including drilling holes on the board/MS clamp including necessay connection etc. as required.32 amps 240 volts DP (rewireable) |
| 98 | Supplying and fixing of powder coated sheet steel enclosure on surface/recess, suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.2+6 / 8 way MCB DB (double door):- |
| 99 | Supplying of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades.(Without regulator) conformimg to IS 374 (1979), BEE 5 |
| 100 | Supplying & fixing of electronic fancy type 5 step fan regulator with cover plate in existing switch board including necessary connection etc as required |
| 101 | Supplying and fixing of the following luminaries (Surface/Recess) including necessary accessories and connection with 2x1.5 sq.mm PVC insulated coper conductor cable(FR) etc. as required. Single box type FTL fittings CRCA sheet steel housing with white reflector cover fitted on the body complete with decorative end cap, 36/40 W FTL, electronic ballast, holder |
AI Tender Summary
Tender Timeline
May 23, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 07, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 07, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender