Repair Works Of Doctors And Staff Quarters At Barajamtala Phc. Under Kulpi Panchayatsamity Under 15Th Fc. Fund.
Tender Value
7.24 Lakhs
Estimated cost
Bid Submission
02 Jun 2022
0 days left
EMD
14500
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kulpi → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair Works Of Doctors And Staff Quarters At Barajamtala Phc. Under Kulpi Panchayatsamity Under 15Th Fc. Fund.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling carefully terraced floor only(including floor finish if any) or lime terracing inground floor roof and removing rubbish asdirected within a lead of 75 m. |
| 2 | Dismantling R.C. floor, roof, beams etc. includingcutting rods and removing rubbish as directedwithin a lead of 75 m. including stacking of steelbars. |
| 3 | Dismantling all types of masonry excepting cementconcrete plain or reinforced, stacking serviceablematerials at site and removing rubbish as directedwithin a lead of 75 m. |
| 4 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints withlocal sand. |
| 5 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground flooras per relevant IS codes.a) Pakur Variety |
| 6 | Brick work with 1st class bricks in cement mortar (1:6)In superstructure, ground floor |
| 7 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 8 | Cement concrete of mix (1:1.5:3) M-20 with graded stone chips (20 mm) |
| 9 | .Dismantling all types of masonry excepting cementconcrete plain or reinforced, stacking serviceablematerials at site and removing rubbish as directedwithin a lead of 75 m. |
| 10 | Reinforcement for reinforced concrete work in all sorts ofstructures including distribution bars, stirrups, binders etcinitial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.I. SAIL/ TATA/RINL |
| 11 | Hire and labour charges for shuttering with centering andnecessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 12 | Dismantling artificial stone flooring upto 50 mm.thick by carefully chiselling without damaging thebase and removing rubbish as directed within alead of 75 m. |
| 13 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]With 1:4 cement mortar10 mm thick plaster |
| 14 | With 1:6 cement mortar(Inside)20 mm thick plaster |
| 15 | With 1:6 cement mortar(Inside)20 mm thick plaster |
| 16 | Neat cement punning about 1.5mm thick in wall,dado,window sill,floor etc. |
| 17 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Sal : Local |
| 18 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hige and other fittings.In ground floor.(In case of non-supply of single plank, penal rate of reduction of 20% will be made). 35mm thick shutters with 19mm thick panel of size 30to 45 Cm.Sishu,Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 19 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately).40mm X 6mm, 250mm Length.(The concreting will have to be done for equivalent thickness of 2 layers of brick work and for the entire width of the wall. No deduction on brick work will be made). |
| 20 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (i)100mm. X 58mm. X 1.90mm. (Add Extra 30% for Oxidised Fittings) |
| 21 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(i) 150mm long x 10mm dia. bolt. |
| 22 | (ii) 225mm long x 10mm dia. bolt. |
| 23 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. 250mm long. |
| 24 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:With continuous plate base (Hexagonal / Round rod).150 mm grip x 10 mm dia rod. |
| 25 | Supplying & fixing 125mm long wooden buffer block.With Sal : Malayasian. |
| 26 | Supplying , fitting and fixing hinge cleat in position excluding the cost hinge and other fiffitngs with 75mm iron Butt-hinge. Sal : Siliguri. |
| 27 | Priming one coat on timber surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 28 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 29 | (a) Painting On timber or plastered surface :With super gloss (hi-gloss) -Two coats (with any shade except white) |
| 30 | Painting On steel or other metal surface :With other than hi-gloss of approved quality-Two coats (with any shade except white) |
| 31 | Supplying fitting & fixing name plate |
| 32 | Electrification |
| 33 | GST |
| 34 | CESS |
| 35 | Contingency |
AI Tender Summary
Tender Timeline
May 17, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJun 02, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 06, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender