Supply Installation Testing And Commissioning Of Himast And Led Street Light Supply Nstalaton Of Hmast Lght 10 Mtr 2 Nos And Led Street Lights At Kfri Sub Center Nilambur
Tender Value
Ref. Documents
Estimated cost
Bid Submission
25 May 2022
0 days left
EMD
12500
Bank guarantee accepted
Document Fee
835
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nilambur → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Supply Installation Testing And Commissioning Of Himast And Led Street Light Supply Nstalaton Of Hmast Lght 10 Mtr 2 Nos And Led Street Lights At Kfri Sub Center Nilambur
BOQ
| Sl. No. | Item Description |
| 1 | Supply and Installation( crane is not allowed in the garden- use necessary scaffoldings while installing) of High mast lighting system as per following specification , 10Mtr high mast system with all its accessories.Mast shaft shal be in single section,Galvanisation of single hot dipped for wind velocity as per IS 875,Head frame assembly 2 point suspension system with steel with steel wire rope 5mm dia(7/9 construction) and winching system arrangement conforming to IS with Galvanised lantern carriage suitable for accommodating 6 LED flood light luminaries symmetricaly and its control gear box lightning spike.The mast shall have an integral three phase operation power tool installed inside the base conpartment for its operation.Supply and convayance foundation bolt made of EN 8 grade special steel along with nuts,washers,anchor plates and templates,supply,erection,testing,and commissioning of LED aviation obstructionlight.It shall also consist of suitable control for power tool three phase motor, manual handle,power cable between panel and mast and giving connection.Construction of suitable shallow foundation with 1:2:4 concrete for the high mast considering safe soil bearing capacity at site as 10T/qmtr at 2 meter depth with reinforcement for RCC works,bend tied and placed in position (plain grill requiring bend cold) using forsteel including form work for reinforced cement concrete and excavation of soil including neat banking .erection and commissuioning of above high mast with the help of crane/derric and outher suitable equipment and wiring of luminaries with wiring materials.Supply and fixing cubicle type MV panel board as per form 4 of IS 8623 including 40 A DP RCBO 100 ma,SP MCB 16A3 nos,32A DP MCB 1no,Cyclic timer with AC coil and giving connection Highmast pole and accessories |
| 2 | Supply and Installation of High mast lighting system as per following specification ,10 mtr high mast system with all its accessories.Mast shaft shal be in single section,Galvanisation of single hot dipped for wind velocity as per IS 875,Head frame assembly 2 point suspension system with steel with steel wire rope 5mm dia(7/9 construction) and winching system arrangement conforming to IS with Galvanised lantern carriage suitable for accommodating 6 LED flood light luminaries symmetricaly and its control gear box lightning spike.The mast shall have an integral three phase operation power tool installed inside the base conpartment for its operation.Supply and convayance foundation bolt made of EN 8 grade special steel along with nuts,washers,anchor plates and templates,supply,erection,testing,and commissioning of LED aviation obstructionlight.It shall also consist of suitable control for power tool three phase motor, manual handle,power cable between panel and mast and giving connection.Construction of suitable shallow foundation with 1:2:4 concrete for the high mast considering safe soil bearing capacity at site as 10T/qmtr at 2 meter depth with reinforcement for RCC works,bend tied and placed in position (plain grill requiring bend cold) using forsteel including form work for reinforced cement concrete and excavation of soil including neat banking .erection and commissuioning of above high mast with the help of crane/derric and outher suitable equipment and wiring of luminaries with wiring materials.Supply and fixing cubicle type MV panel board as per form 4 of IS 8623 including 40 A DP RCBO 100 ma,SP MCB 16A3 nos,32A DP MCB 1no,Cyclic timer with AC coil and giving connection Highmast pole and accessories |
| 3 | Supply,installation ,testing and commissioning of 12X150W flood light with all accessories, surge protection 10KV with modules integrated with self supported frame wprk.high efficiancy poly carbonate diffuser for glare free, efficiancy up to 150 lumen/Watt,protection IP 68 for LED module and IP 67 for LED driver suitable for operation of 240 V,50Hz AC supply |
| 4 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level,Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 5 | Providing and laying in position reinforced cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of Highmast light. including form work etc. as required (As per drawing ,excluding reinforcement). |
| 6 | Earth work in excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. |
| 7 | Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame) |
| 8 | 40A DP RCBO |
| 9 | 40A DP Isolater |
| 10 | timer with Ac coil |
| 11 | 32 A SP MCB |
| 12 | 2 pole contactor |
| 13 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required. |
| 14 | Supply andLaying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation,protective covering and refilling the trench etc as required.4 core 25 sq. Mm |
| 15 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 16 | Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. |
| 17 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 18 | supply and errection of GI street light pole as per attched drawing includingearth workexcavation ,plastering, and concreting with cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) with the following accessories (a) 2 inch size class B GI pipe 3.5 mtre(0.5 mtr bellow ground level) long for street light pole with primer and painting.(b) 25 mm B class GI pipe approximate 1 mtr long welded to main pole for Fixing 20 W LED fixture.(c) 40 mm size class B GI pipe of approximate length 1.5 mtr on each street light pole for cable connection from bottom to syntex junction box.(d)suitable PVC junction boxof approved size 200X150X100 mm wetther proof on the stree light pole with connection strip/terminals and6 A two pole isolater and giving conncetion |
| 19 | supply and fixing 20 mm LED street light suitable for above pole and giving connection using 1.5 sq. mm 3 core copper cable |
| 20 | Supply andLaying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation,protective covering and refilling the trench etc as required.3 core 10 sq. mm |
AI Tender Summary
Tender Timeline
May 12, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMay 25, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMay 30, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender