Supply Of Furniture And Renovation Of 3 Nos Room At 10 Th Floor, North Block Of Jalasampad Bhawan, Sector - I, Salt Lake For Accommodating The Office Of The Director Of The Cfppe-Wb-2 Rendering The Surface Of Walls And Ceiling With White Cement B, 24 Paraganas North-West Bengal

Supply Of Furniture And Renovation Of 3 Nos Room At 10 Th Floor, North Block Of Jalasampad Bhawan, Sector - I, Salt Lake For Accommodating The Office Of The Director Of The Cfppe-Wb-2 Rendering The Surface Of Walls And Ceiling With White Cement Base Water Proof Wall Putty Of Approved Make & Brand. ( 1.5 Mm Thick ) 3 Applying Interior Grade Acrylic Primer Of Approved Quality And Brand On Plastered Or Cencrete Surface Old Or New Surface To Receive Distemper / Acrylic Emulsion Paint Including Scraping And Preparing The Surface Throughly, Complete As Per ManufacturerS Specification And As Per Direction Of The Eic. ( In Ground Floor ) . One Coat Water Based Interior Grade Acrylic Primer. 4 Applying Acrylic Emulsion Paint Of Approved Make And Brand On Walls And Ceiling Including Sand Papering In Intermediate Course Including Putty ( To Be Done Under Specific Instruction Of Superintending-Engineer ) Two-Coats. ( I ) Standard Quality 5 Supplying Bubble Free Float Glass Of Approved Make And Brand Conforming To Is 2835-1987.I ) 4Mm Thick Clear Glass. 6 Ii ) 4Mm Thick Coloured / Tinted / Smoke Glass 7 Providing And Fixing Of 15Mm Thick Mineral Fibre Acoustic Ceiling Tiles Of Approved Pattern And Size 595Mm X 595Mm Should Be Placed In The Grid Module To Form A False Ceiling With Nrc Value = 0.6 Material Class: A2-S1, D0 As Per En 13501-1, Fire: Rei – Rei120 As Per En 13501- 2, Surface Burning Characteristics: Class 1 Or A As Per Astm E 84 ) With Powder Coated Exposed G.I. Grid Suspension System ( Interlocking T-Grid, Having Load Carrying Capacity With Mid Span Deflection Not Exceeding 1 / 360 Span With Hanger Spacing Of 1200Mm C / C ) Consisting Of Main Runner 3600 Mm Long, Cross Tee 1200 Mm / 600 Mm Long And Wall Angle. The Wall Angle Shall Be Fixed On Pvc Dash Fasteners On The Perimeter Of The Wall By Steel Screws With Distance 300Mm C / C. The Main Runners To Be Placed @ 1200 Mm. The Cross Tee 1200Mm Will Be Inserted In The Pre-Cut Slots Of Main Runner At A Regular Interval Of 600 Mm To Form A Modular Grid Of 1200Mm X 600Mm. Additional Cross Tees Of 600 Mm Shall Be Placed Perpendicular To The Cross Tee 1200 Mm Long To Finally Form A Grid Of 600 Mm X 600 Mm. Grid Of Module Size 600 Mm X 600 Mm Shall Be Supported By 6 Mm Dia G.I. Wire From Purlins / Soffit. All Complete As Per The Drawing & Directions Of Engineer-In-Charge. In Ground Floora ) With 15 Mm Thick Mineral Fibre False Ceiling Tile ( Nrc = 0.6 As Per Astm C 423 & Sound Attenuation - 34Db As Per En Iso 10848 ) 8 Providing And Fixing In Position Roller Blind Of Approved Make And Brandas Per Drawing, Design And Direction Of Eic. Fabric Description: Fibre-Glass Coated Fabric, 0.30Mm Thick, 62 Threads Per Sq In., 0.750 Lbs Per Sq In. ( 441G Per Sq Mt. ) . Fabric Width: As Per Site Condition With Up-Stand Along The Length Of The Dry Pocket, Removable Type For Servicing Shades. Operation: Manual. Mounting: Pocket Mounted. ( Pocket To Be Provided By Other Agency ) . Shade Orientation: Regular Roll, Shade Cloth Falls At Window Side Of Roller. Configuration: Single Band. Closure With Up-Stand Along The Length Of The Dry Pocket, Removable Type For Servicing Shades. 9 Supplying Fitting Fixing Fabricating And Erecting Low Height Partiton Of Modular Grid System Of Approved Make As Per Drawing Design And Direction Of Eic The Thickness Of The Partiton Is 50 To 53Mm .The Partition Offrame Work Is 1.5 Mm Thick Crca Sheet Frame Work With Powder Coated ( 40-50 Micron ) Fitted And Fixed In Position As Per Drawing And Direction Icludind Providing Height Abjuster Below Ceiling / Floor Allow For Cutting Chases To Wall And Floors And Mending Good Damages Frame Are To Be Fitted With Masonnry / Rcc Surface By Means Of Approved Metal ( Brass ) Expansion Fastener The Rate Should Include For Proviiding Minimum 120-130 Mm Wide Box Type Wire Managemement Just Above / Below The Table Top As Well As Skirting Level For Wire Management System. To Be Fabricated With Crca Sheet Of Minimum 0.8 Mm Thick Finished With Powder Ccated 40 To 50 Micronsuitable Provision For Swith Board And Sockets Outlets As Per Requirements For Power Line And Data / Tele Lines Along The Base And At The Table Height As Specified .The Skirting Will Be Fabricated Out Of 20 Swg Ms Sheet The Skirting Will Be Approachable From Both Sides And Will Have Channels For Adjustment For Floor Panels Of Partition Are To Be Fitted By Using Aluminnium Profiles And Pvc Extrusions Are Used As Trimmings .All Metal Sections.Fabricated Ms Components And Alluminium Profiles Are Finished In 40 To 50 Micron Epoxy Powder Coting Of Approved Shade All Exposed Edge And Visible Are Will Be Covered With Minimum Of 1.2 Mm Thick Crca Trim And Alljoints Like T L And ? Will Be Covered Will Alluminium Caps. No Pvc Cap Will Be Allowed Here The Rate Should Be Including Provision Of Slots As Per Site Requirement In Vertical Member For Cantilevered Accessories Like Overhead Store . Work Top Etc .All Complete As Per Drawing ( Drawing Sheet - 1 ) And Directions With All Labour And Materials ( I ) Partition Facia Fabricated With Minium 199 Mm Thick Ply With Both Side 1.5 Mm Thick Laminnationply / Magnatic / Fabric / Soft Board / Laminated White Board Of Approved Shades On Both Sides Of The Frame Work Fitted With Connectors All Complete As Per Drawing And Direction Of Eic. 10 Supplying , Fitting, Fixing Work Station Of Approved Make And Brand As Per Drawing, Design, And Direction Of Eic.Supplying And Fixing Of Approved Make Minimum 19 Mm Thick Ply ( Century / Green ) With Both Side Lamination Of Approved Shade. All The Edges Will Be Chamfered And Finished With Pvc Lipping Of 1.2 / 2.0 Mm Thickness. The Frame Will Have The Necessary Provisions For Suspending Drawer Units And Fixing Of Sides Or Thick 19 Mm Thick Ply Without Frame Work. The Workstaton Should Be Fitted With Cantilevered Brackets To Tables And Attached To The Partition Frame Work. The Keyboard Treys Shall Be Minimum 500 Wode Of 18 Guage Mild Sheet Body With Anti Rust Treatment. This Shall Be Finished With 50 Micron Powder Coated In Epoxy Paint. The Key Board Trays Shall Be Fixed Bellow Table Top With Necessary Hardware For Easy Sliding. The Cpu Trolley Of Size 240 X 240 X 245 Mm. Having Adjustable Width And Lockable Castors Made Of 18 Guage Thick Steel Sheet With Powder Coating Of 50 Micron. Modesty Panels, Board Side Gable End Whereever Necessary Will Be Fabricated Out Of Minimum 19 Mm Ply.All Board Components Tops, Sides Etc Are Finished Wih Laminated And All The Edges Chamfered At 45 Dgree. The Rate Should Include Necessary Approved Hardwarw Fittings For Fixing The Table Top. Modesty Panels, Side Board Etc Including Making Hole On The Table Top Connecting The Wire, The Hole To Be Covered With Dark Coloured Pvc Insert ( Wire Manager ) With Movable Part To Put Wires And Socket And Nearly Cover The Hole. All Complete As Per Drawing And Direcion With All Labour And Materials.Supplying, Fitting, Fixing Of Main Work Top 1200Mm X 600 Mm. All Complete As Per Drawing ( Drawing Sheet- 2 ) Of Eic 11 Supplying, Fitting, Fixing Mobile Drawer Unit Of Approved Make And Brand As Per Drawing, Design And Direction Ofeic. Supplying Mobile Drawer Unit Of Approved Make , The Facia, Made Of Minimum 19 Mm Thick Plywood With 1.5 Mm Thick Lamination. The Top And Sides Made Of Minimum 19 Mm Thick Ply Wood And The Back Will Be Made Of Minimum 19 Mm Thick Ply Wood Of Approved Shade And Quality. The Drawers Are Fabricated Out Of Ms Sheets And Assembled With Drawer, Runners For Smooth Operation. A Single Centerl Locking System Of Approved Quality To Be Provided. All Metal Components Will Be Finished In Black Epoxy Powder Coating Of 40-50 Micron ( Approx ) . Rate Should Be Including Necessary Approved Quality Hardware Fittings. All Complete As Per Drawing ( Drawing Sheet- 3 ) And Direction With All Labour And Materials. Size Of Drawer Unit 400 / 470 Mm. X 495 / 450 Mm. X 700 Mm. ( A ) Ground Floor 12 Godrej Make Executive Mid Back Chair, Model: Ace ( Colour: Black ) . 13 Godrej Make Visitor Chair, Model: Bravo ( Colour: Black ) .

Refer document

INR 7.28 Lakhs /-