Maintenance Of Sks Thariyodu Maintenanace Of Sks Thariyodu
Tender Value
4.27 Lakhs
Estimated cost
Bid Submission
18 May 2022
0 days left
EMD
10700
Bank guarantee accepted
Document Fee
900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wayanad → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Maintenance Of Sks Thariyodu Maintenanace Of Sks Thariyodu
BOQ
| Sl. No. | Item Description |
| 1 | DSR.2.6.1. Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil |
| 2 | DSR 4.1.8.Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size). |
| 3 | DSR 5.22A.6. Reinforcement for RCC work bent tied and placed in position using torsteel including cost and conveyance of all materials labour charges etc. complete Thermo-Mechanically Treated bars of grade Fe-500 D or more. |
| 4 | 5.9.6. Centering and shuttering including strutting, propping etc. and removal of form for all heights: Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 5 | DSR 5.1.3. Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 6 | OB.PWD.26. Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure above plinth level up to floor five level for 10 cm thick wall in: CM 1:6 (1 cement : 6 coarse sand) including cost of scaffolding etc complete |
| 7 | DSR 13.1.1. Plastering with cement mortar 1:4, 12mm thick one coat floated hard and trowelled smooth including cost and conveyance of all materials, labour charges etc. complete for walls. |
| 8 | 14.1.1. Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand). |
| 9 | 22.6. Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment. |
| 10 | 13.109.1. Finishing walls with water proofing cement paint of required shade : old work (one or more coats applied @ 2.2 kg/10 sqm). |
| 11 | 13.99.1. Paintingwith synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Old work (one or more coats) |
| 12 | 15.52. Dismantling of flushing cistern of all types (C.I./PVC/Vitreous China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 13 | DSR.17.2.2. Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 14 | 15.23.1. Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 15 | 11.37. Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. |
| 16 | 50.18.9.9.2. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 110 mm dia 4 Kgf/cm2 |
| 17 | 50.18.9.7.2. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 4 Kgf/cm2 |
| 18 | 50.18.9.22.6. Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 110 x 110 x 110 mm dia Door Tee |
| 19 | 50.18.9.20.6. Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 63 x 63 x 63 mm dia Door Tee |
| 20 | 50.18.9.20.4. Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 63 mm dia Bend |
| 21 | 50.18.9.20.7. Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 63 mm dia Vent cowl |
| 22 | 50.18.9.22.3. Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 110 mm dia Door Elbow |
| 23 | Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 110 x 110 x 110 mm dia Tee |
| 24 | Providing and fixing PVC moulded fittings / accessories forRigid PVCpipes, including jointing with PVC solvent cement - 110 mm dia Vent cowl |
| 25 | 50.18.9.2.2. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm dia 10Kgf/cm2 |
| 26 | 50.18.9.4.1. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 32 mm dia 10Kgf/cm2 |
| 27 | DSR.18.15.2.Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 20mm nominal bore. |
| 28 | 50.17.1.4. .Supplying and fixing CP Health Faucet superior quality including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 29 | 10.16.1. Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 30 | DSR.12.5. Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per IS:277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 31 | DSR 18.17.2.Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm bore |
| 32 | 18.48. Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 33 | DSR 16.70.1. Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction ofEngineer-in-charge. Made of G.I. wire of dia 4 mm |
| 34 | OD.PWD.228.Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of 6 mm metal, filling the joints with M sand etc. all complete as per the direction of Engineer-in-charge.(Modified DSR 16.68) |
| 35 | 21.1.1.2.Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 36 | 21.1.2.1. For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 37 | 21.3.1.Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness |
| 38 | 50.9.5.1. .Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Using Anjili wood/ Jack wood 35mm thick shutters (Modified D.S.R 9.9.1.1) |
| 39 | 50.9.15.5. Supplying and fixingiron hooks and eyes 100 mm size |
| 40 | 9.56.4. Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : 50x40x2.50 mm |
| 41 | 9.77. Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 42 | 9.141. Providing and fixing PVC Door Frame and panell of size 50x47mm with a wall thickness of 5 mm (± 0.2 mm) made out of single piece extruded PVC profile, with mitred cut joints and joint with 2nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8x100mm long anchor fasteners complete, all as per manufacturer\"s specification and direction of Engineer -in- charge. |
| 43 | Floor trap 110 mm as per the direction in engineer |
AI Tender Summary
Tender Timeline
May 09, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMay 18, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMay 20, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender