Supply, Testing, Installation And Commissioning Of Different Tools, Equipment And Machineries Of Self Employed Tailor, Chauffeur L5 Trade ( Short Term Course ) And Solar Technician ( Electrical ) , Fitter Trade ( Cts ) Under Stri

Sharing tender

Supply, Testing, Installation And Commissioning Of Different Tools, Equipment And Machineries Of Self Employed Tailor, Chauffeur L5 Trade ( Short Term Course ) And Solar Technician ( Electrical ) , Fitter Trade ( Cts ) Under Strive Project At Iti Midnapore- 1 Firstaidbox 2 Seamripper3” 3 Measuring Tape:Tailor’S Tape, Length 5’ Wide ½ “, Nylon Type 4 Calculator ( Non Scientific ) 5 Clutch Plate, Pressure Plate Setlmv Type 6 Engine Parts Like Piston, Liner Set 7 First Aid Kit 8 Front Axle Lmv Type 9 Gear Box Synchromesh Typelmv 10 Propellershaft Lmv Type 11 Rear Axle Lmv Type 12 Wall Charts On Various Systems Like Lubrication 13 Pyroheliometeriso:9060 First Class Ms - 57, Spectral Range: 200 To 4000Nm, Irradiance Range: 0 - 4000 W / M², Temperature Range: -40 To +80° C 14 Cut Models Of Photo Voltaic Cell Assemble With Mono Crystalline Module, Amorphous Silicon Module, Thin Film Module, Poly Crystalline Module 15 Solar Photovoltaic Module---250 W Thin Film Module, 16 Dc Pump 24 V 17 A. ) Compressor Unit Suitable For Pressure: 8 Bar, Delivery: 50 Lpm ( Or More ) , Reservoir Capacity: 24 Liters ( Or More ) , 230V, 50 Hz, With Pressure Regulator And Water Separator – 01 No. B. ) Pneumatic Trainer Kit, Each Consisting Of The Following Matching Components And Accessories:--- 01 Set I. Single Acting Cylinder Max. Stroke Length 50 Mm, Bore Dia. 20 Mm -1 No Ii. Double Acting Cylinder Max. Stroke Length 100 Mm, Bore Dia 20 Mm, Magnetic Type -1 No Iii. 3 / 2-Way Valve Manually-Actuated, Normally Closed -2 Nos. Iv. 3 / 2-Way Valve Pneumatically-Actuated, Spring Return -1 No V. One-Way Flow Control Valve - 2 Nos. Vi. 5 / 2-Way Valve With Manually-Operated Switch -1 No Vii. 5 / 2-Way Valve Pneumatically-Actuated, Spring Return -1 No Viii. 5 / 2-Way Pneumatic Actuated Valve Double Pilot -1 No Ix. 3 / 2-Way Roller Lever Valve Direct Actuation Normally Closed -2 Nos. X. Shuttle Valve ( Or ) -1 No Xi. Two-Pressure Valve ( And ) -1 No Xii. Pressure Gauge 0-16 Bar - 1 Nos. Xiii. Manifold With Self-Closing Nrv, 6-Way -1 No Xiv. Pushbutton Station For Electrical Signal Input With 3 Illuminated Momentary-Contact Switches ( 1 No + 1 Nc ) And 1 Illuminated Maintained- Contact Switch ( 1 No + 1 Nc ) , Contact Load 2A -1 No Xv. Relay Station With 3 Relays Each With 4 Contact Sets ( 3No+1Nc Or Change-Over Type ) , 5 A -1 No Xvi. 3 / 2-Way Single Solenoid Valve With Led -1 No Xvii. 5 / 2-Way Single Solenoid Valve With Manual Override And Led -1 No Xviii. 5 / 2-Way Double Solenoid Valve With Manual Override And Led -1 No Xix. Power Supply Unit, Input Voltage 85 – 265 V Ac, Output Voltage: 24 V Dc, Output Current: Max. 4.5 A, Short-Circuit-Proof. -1 No Xx. Profile Plate, Anodized Aluminium 1100X700 Mm, With Carriers, Mounting Frames And Mounting Accessories ( To Be Fitted Onto The Pneumatic Workstation ) -1 Set C. ) Pneumatic Workstation With 40 Square Mm Aluminum Profile Legs, Wooden Work Surface, And One Pedestal Drawer Unit Having 5 Drawers, Each With Handles And Individual Locks, On Metallic Full Panel Drawer Slide:- 01 No. ( 1 ) Worktable – Size ( Approx. ) L 1200Mm X W 900Mm X H 900 Mm, With Four Castor Wheels Including Two Lockable Wheels At The Front Side, ( 2 ) Drawer – Size ( Approx. ) – L460mm X W495mm X H158mm Each, And Overall Size Of Drawer Unit ( Approx. ) -L470mm X W495mm X H825m M And ( 3 ) Drawer Slide Height ( Approx. ) 85Mm. - D. ) Carrier For Mounting Components, Such As Pb & Relay Boxes. – 01 No. E. ) Cut Section Model For Pneumatic Components – 01 Set 18 A. ) Hydraulic Trainer Kit, Each Consisting Of The Following Matching Components And Accessories:- 01 Set I. Hydraulic Power Pack With ( 1 ) External Gear Pump Having A Delivery Rate Of 2.5 Lpm, ( Approx. ) @ 1400 Rpm Operating Pressure 60 Bar, Coupled To A Single-Phase Ac Motor ( 230 Vac ) Having Start Capacitor And On / Off Switch And Overload Protection, ( 2 ) Pressurerelief Valve Adjustable From 0 – 60 Bar, ( 3 ) Oil Reservoir, ≥5 Litres Capacity Having Sight Glass, Drain Screw, Air Filter, Andp And T Ports. Ii. Pressure Relief Valve Pilot-Operated - 1 No Iii. Drip Tray, Steel Size 1160 Mm X 760 Mm. - 1 No. Iv. Pressure Gauge Glycerin-Damped, Indication Range Of: 0 – 100 Bars -1 No. V. Four-Way Distributor With Five Ports, Equipped With A Pressure Gauge -1 No. Vi. Double Acting Hydraulic Cylinder With A Control Cam, Piston Diameter16 Mm, Piston Rod Diameter10 Mm, Stroke Length 200 Mm. - 1 No. Vii. Suitable Weight For Vertical Loading Of Hydraulic Cylinder - 1 No. Viii. Mounting Kit For Weight For Realizing Pulling And Pushing Load. -1 No. Ix. 3 / 2-Way Directional Control Valve With Hand Lever Actuation. -1 No. X. 4 / 2-Way Directional Control Valve With Hand Lever Actuation. -1 No. Xi. 4 / 3-Way Directional Control Valve Closed-Center Position, With -1 No.Hand Lever Actuation. - Xii. Non-Return Valve.-1 No. Xiii. Pilot-Operated Check Valve Pilotto Open. -1 No. Xiv. One-Way Flow Control Valve With Integrated Check Valve. -1 No. Xv. T-Connector With Self-Sealing Coupling Nipples ( 2 Nos. ) And Quick Coupling Socket ( 1 No. ) .-2 Nos. Xvi. Profile Plate, Anodized Aluminum, 1100X700 Mm, With Carriers, Mounting Frames And Mounting Accessories ( To Be Fitted Onto The Hydraulic Workstation ) -1 Set B. ) Hydraulic Workstation With 40 Square Mm Aluminum Profile Legs, Wooden Worksurface, Andonepedestaldrawer Unit Having 5 Drawers, Each With Handles And Individual Locks, On Metallic Full Panel Drawer Slide:- 01 No. ( 1 ) Worktable – Size ( Approx. ) L1200mmxw900mmxh900 Mm, With Four Castor Wheels Including Two Lockable Wheels At The Front Side, ( 2 ) Drawer – Size ( Approx. ) – L460mmxw495mm Xh158mm Each, And Overall Size Of Drawer Unit ( Approx. ) L470mmxw495mmxh825m M And ( 3 ) Drawer Slide Height ( Approx. ) 85Mm. C. ) Cut-Section Models For Hydraulic Components – 01 Set