|
| 1 | NOTE (Applicable for all items) :- The bidders/contractorsare advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. |
| 2 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rubbish off the premises. |
| 3 | M&L Rendering 10 mm thick cement plaster in CM 1:4 on fair faces of brick Work (internal surfaces)for fixing of wall tiling. |
| 4 | M&L for 15 mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes for non skid ceramic and grinaite tiles . |
| 5 | M&L Glazed ceramic coloured tiles 450 x 350 x 7 mm thick colouredtiles as in dado, skirting and vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles. |
| 6 | M&L Non Skid coloured ceramic tiles 7 to 8 mm thick areaof each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement. |
| 7 | M&L Non Skid coloured ceramic tiles 7 to 8 mm thick areaof each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement. |
| 8 | M&L for vertifiedceramic tiles 10mm thick light shade (Square/rectangular) polished area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to matchcomplete all as specified and directed. |
| 9 | M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete |
| 10 | M & L for Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. |
| 11 | M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors |
| 12 | M & L for anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same |
| 13 | M & L for anti-termite treatmentOf voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors |
| 14 | Dismantling of wrought iron or mild steelwork of any description. |
| 15 | Taking down asbestos cement corrugated or semi corrugated sheet in roof covering complete all as specified and directed |
| 16 | S&F for MS rolled section, roof trusses (framed), trussed, purlins, rafters, columns , plates, cleats and fastenings and heavy bracket framing (beam, tee, angle channel or flat sections) of Fe-410 -W(Gde E-250) quality-B etc complete all as specified and directed. |
| 17 | M&L 0.5 mm thick pre painted galvalume aluminium zinc coating GI based corrugated steel sheet of coiour having tensile strength of 550 Mpa as in roof covering with selftapping screws as specified. |
| 18 | M&L 0.5 mm thick pre painted galvalume aluminium zinc coating GI based Plainsteel sheet of coiour having tensile strength of 550 Mpa as in roof covering with selftapping screws as specified. |
| 19 | Taking out existing roof treatment and taking out existing cracked plaster by taking out and wire bruishing and cleaning the existing surface with water etc. |
| 20 | M&L PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in pading concrete for getting proper slope of roof/covering etc as specified and directed. |
| 21 | M& Lforbituminous primer @ 0.30 Kg/Sqm over the 10mm thick cementplaster CM 1:3with water proofing compound inclpreparation of surfacesas permanufacturers instruction complete all as specified andas directed. |
| 22 | M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3.mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed. |
| 23 | M & L for finishing the Bituminous surface with aluminium paint @0.15 Ltr/sqm as per manufactures specifications and under strict supervision of manufactuer\"s technical representative complete in all respects as directed. |
| 24 | Demolition of brick work built in cement mortar incl quoin, arches etc complete all as specified and directed. |
| 25 | M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6 mtr mean radius, built in CM 1:6. |
| 26 | Taking down cementplaster on brick orstone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. |
| 27 | M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:4) finished surfaces even and smooth complete all as specified and as directed. |
| 28 | M & L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 29 | Dismantling of wall and ceiling boards(fiber,pulp,insulation etc) or insulation board slabs etc any thicknessincl cover fillets. |
| 30 | S&F 605 x 605 mm anodised Aluminium snap grid frame work for false ceiling incl fixing fixing of nut bolt clamps with the help of drilling matching etc. complete all as specified and directed. |
| 31 | M & L Non asbestos fibre cement building boards in 4 mm thick ceilingfixed or laid/inserted to Aluminium frame work with screw as per manufacturers instructions. |
| 32 | S & F Hangers 6 mm dia. G.I. (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm long complete all as specified. |
| 33 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 34 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P brass/ stainless steel screws, complete all as per manufacturer\"s specification and all as directed. |
| 35 | Providing and fixing Powder coated aluminium (minimum thickness of powde coating 50 micron) for shutters of doors, windows & ventilators including roviding and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as per manufacturer\"s specification and all as directed. |
| 36 | M & L for 5.50 mm thick Sheet glass, ordinary quality and glazing with oil putty in squareexc 0.5 sq. m in each panel |
| 37 | Taking down chowkath or frameexc 1.5 sqm n exc 4 sqm with shutter ( without taking of shutters from frames ) complete all as specified and directed. |
| 38 | Taking down chowkath or frame n exc 1.5 sqm with shutter ( without taking of shutters from frames ) complete all as specified and directed. |
| 39 | Resecuring or easening, adjusting without taking down of shutters exc 1 Sqm and n.exc 2 Sqm each in situ. |
| 40 | S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, frame rabated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 41 | S/F 35mm thick 2nd class HW glazed and Skelton shutter open rebated and prepared and to receive gauze etc without sash bar. |
| 42 | S/F 35 mm thick factory made (single panel ) with lock rail and panel of 9 mm BWP commercial plyor 12 mm veneered particle boardwith commercial veneering on both faces klin seasoned and chemically pressure treated. |
| 43 | S&F 30mm thick 2nd class HW, glazed and skelton shutters open rebated and prepared to receive glass / gauge (without sash bar) edges of forming plain chamfered orrounded fitted with cut and mitred bead for securing glass / gauge etc size of shutter as per SSR part-1 section 8 clause 8.24(a). |
| 44 | S/F factory made solid panel PVC door shutter prelaminated one side 30 mm thick(style) conisiting of frame made out of M S tubes for top and bottomrails. MS frame shall be covered with heat moulded plain colour PVC ;C; channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail. Pannelling of plain colour PVC sheet to be fitted ithe MS frame welded/sealed to the stile and rail with suitable PVC sheet bedding and jointed with solvent cement as per manufacturer\"s specification and complete all as directed. |
| 45 | S&F solid PVCdoor frame of size 50 mm x 47 mm made out of5 mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawing. |
| 46 | S&F 150 mm long aluminium,anodised barrel tower bolts of extruded section. |
| 47 | S&Faluminium sliding door bolt 300mmlong, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate. |
| 48 | S&F 100 mm size steel butt hinges mediumweight , cold rolled. |
| 49 | S&F 75 mm size steel butt hinges medium weight , cold rolled. |
| 50 | S&F 300 mm longms ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 51 | S&F in repair 300 mm longms ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 52 | S&F 150 mm Extruded aluminium alloy handles, fabricated type, anodisedcast type, anodised. |
| 53 | S&F 75 mm Extruded aluminium alloy handles, fabricated type, anodisedcast type, anodised. |
| 54 | S&F 150mmfloor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring , fixed in floor. |
| 55 | S&F galvanised stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire stapple |
| 56 | S/F sheet glass ordinary quality and glazing with oil putty not exe 0.5 sqm in each pane 4 mm thick |
| 57 | Supply and fix 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane putty in squares not exceeding 0.50sqm in each pane complete all as directed. |
