Rate Of Different Articles For Beautification Of Buniadpur Municipal Office Building- 1 Manufacturing, Supplying, And Installing Fiber Composite Structural Sheet Of Decorative Gazebo Top On Existing Rcc Rooftop Around The Periphery Over Existing 8Nos.

Sharing tender

Rate Of Different Articles For Beautification Of Buniadpur Municipal Office Building- 1 Manufacturing, Supplying, And Installing Fiber Composite Structural Sheet Of Decorative Gazebo Top On Existing Rcc Rooftop Around The Periphery Over Existing 8Nos. Rcc Column 300 Dia.Havinginternal Dia. 10400 Mmaround The Periphery Cicular In Shape With Reinforced By 4 Mm Sq. Bar Covered By Glass Fiber Reinforced Polyester Or Vinyl Ester Resin Matrix, Approximately 50% Glass By Weight. A Synthetic Surface Veil Shall Be The Outermost Layer Covering The Exterior Surfaces. Glass Strand Roving’S Shall Be Used Internally For Longitudinal Strength Specially For Coastal Area. The Frp Having Density May Be Between 1, 2 G / Cm3 And 2, 0 G / Cm3 And Panels Are About 0.09 Inch In Thickness, Fiber Mass Fraction 60-80%, Fiber Volume Fraction 50-60%, Water Absorption: = 0.2%, Synthetic Surface Veil Fabric Must Encase The Glass Reinforcementand Weigh About 12 Ounces Per Square Foot Depending On The Site Condition. All The Steel Column Surface And Other Exposed Surface Should Be Cover By Decorative “Frp” Laminates. The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture The Frp Components In Accordance With Any Structural Drawings Provided By The Eic.The Manufacturer / Supplier Shall Provide Full Details Of The Frp Materials, Including All Associated Manufacturing Processes, Test Certificates, Adhesive, And Fasteners.Relevant Construction And / Or Structural Drawings For All Frp Components Shall Be Submitted To The Eic For Approval In Accordance With The Requirements As Per This Specification.Frp Roof -Specification & Details Color : As Desired Material : Frpsize=12000 Mmtype=Circular In Shapeheight = 2400 Mm Projection From Outer Column Face=500 Mm ( Average ) Waterproof : Yes ( Attched Image In Annex.I ) 2 Manufacturing, Supplying, And Installing Of Frp Made Netaji With Horse Scalpture On Existing Base ( Approx.2.5 M Height ) High Quality Finish At Site With Fire Resistive Resin Coatingand Also Extra Strong Uv-4 Protected Against Fading Withthickness Of 4 Mm.Rate Should Be Included Included All Structural Framing Work By Iron Angle, Plate, Nut And Screw, Welding Work Etc . The Artistry Of The Knight Makes That The Center Of Attention Of This Larger-Than-Life-Sizeset.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture.Specification:Material: Fiberglass ( Raw Materials: Fiber Sheets, Resin, Hardner, Fiber Chalk Etc ) Height: 10 Ft. ( Approx. ) ( Attched Image In Annex.I ) 3 Supply, Installation, Testing And Commissioning Of Roman Antique Free Fall Fountain Forpark Under Buniadpur Municipality.The Bidder Is Advised To Visit The Proposed Site Under Municipality Where The Installations Are To Be Carried Out, Before Submitting Their Tender. It Is The Duty Of The Supplier To Ascertain That The System Supplied By Them Has To Fit To The Existing Area And Function Effectively And Efficiently As Per The Existing Specification.Specification Of Water Fountain 1. Pumps: Submersible Kirloskar 2 Hp For Electric Pump For Getting The Required Water Fountain.The Type, Power, Model, Make And Other Specifications Of The Pumps Should Be Mentioned In Case Of New.2. Frame: The Supporting Stands Of The Fountain Frame Should Of Suitable Non Corrosive Sections. 3. Pipes: Using Suitable Non Corrosive Sections For New And Utilised Existing Usable Upvc Pipe. 4 Nozzles: Nozzles Should Be Of Brass Or Suitable Non-Corrosive Metal For Trouble Free Operation. 5. Valves: Suitable Upvc Valves For Getting Fountain And Water Effects. 6. Cables: Isi Certified Submersible Cables Or Equivalent, Suitable For The Proper Functioning Of Fountain. 7. Lights: As Per Requirement.8. Control Panel: Suitable Control Panel For Running The Above. Details And Specifications Need To Be Specified And Consult With Dsda Electrical Engineering Team. The Power Supply Available At Site Is In Single Phase 210 Volts 50 Hertz And Three Phase 415 Volts, 50 Hertz Alternating Current Supply System And All The Equipment’S Supplied Should Be Made To Operate In The Above Power Supply System.9. Safety Standards: The Entire System Should Conform To All Safety Standards Demanded By Electrical Rule. ( Attched Image In Annex.I ) Frp Structure As Per Image. Supplying, And Installing Of Frp Madescalpture On Existing Basehigh Quality Finish At Site With Fire Resistive Resin Coatingand Also Extra Strong Uv-4 Protected Against Fading Withthickness Of 4 Mm.Rate Should Be Included Included All Structural Framing Work By Iron Angle, Plate, Nut And Screw, Welding Work Etc . The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture.Specification:Material: Fiberglass ( Raw Materials: Fiber Sheets, Resin, Hardner, Fiber Chalk Etc ) Height: 8 Ft. ( Approx. ) 4 Supply, Installation, Testing And Commissioning Of Roman Antique Free Fall Fountain Forpark Under Buniadpur Municipality.The Bidder Is Advised To Visit The Proposed Site Under Municipality Where The Installations Are To Be Carried Out, Before Submitting Their Tender. It Is The Duty Of The Supplier To Ascertain That The System Supplied By Them Has To Fit To The Existing Area And Function Effectively And Efficiently As Per The Existing Specification.Specification Of Water Fountain 1. Pumps: Submersible Kirloskar 2 Hp For Electric Pump For Getting The Required Water Fountain.The Type, Power, Model, Make And Other Specifications Of The Pumps Should Be Mentioned In Case Of New.2. Frame: The Supporting Stands Of The Fountain Frame Should Of Suitable Non Corrosive Sections. 3. Pipes: Using Suitable Non Corrosive Sections For New And Utilised Existing Usable Upvc Pipe. 4 Nozzles: Nozzles Should Be Of Brass Or Suitable Non-Corrosive Metal For Trouble Free Operation. 5. Valves: Suitable Upvc Valves For Getting Fountain And Water Effects. 6. Cables: Isi Certified Submersible Cables Or Equivalent, Suitable For The Proper Functioning Of Fountain. 7. Lights: As Per Requirement.8. Control Panel: Suitable Control Panel For Running The Above. Details And Specifications Need To Be Specified And Consult With Dsda Electrical Engineering Team. The Power Supply Available At Site Is In Single Phase 210 Volts 50 Hertz And Three Phase 415 Volts, 50 Hertz Alternating Current Supply System And All The Equipment’S Supplied Should Be Made To Operate In The Above Power Supply System.9. Safety Standards: The Entire System Should Conform To All Safety Standards Demanded By Electrical Rule. ( Attched Image In Annex.I ) Others ( Pumps, Frame, Pipes, Nozzles, Valves, Cables, Lights, Control Panel Etc. ) 5 Manufacturing, Supply , Installation Of Frp Model Biswa Bangla On Hand Covered By Artificial Grass At Park Under Buniadpur Municipality.High Quality Finishwith Fire Resistive Resin Coatingand Also Extra Strong Uv-4 Protected Against Fading Withthickness Of 4 Mm.Rate Should Be Included Included All Structural Framing Work By Iron Angle, Plate, Nut And Screw, Welding Work Etc . The Frp Having Density May Be Between 1, 2 G / Cm3 And 2, 0 G / Cm3 Andabout 0.09 Inch In Thickness, Fiber Mass Fraction 60-80%, Fiber Volume Fraction 50-60%, Water Absorption: = 0.2%The Manufacturer / Supplier Shall Provide Full Details Of The Frp Materials, Including All Associated Manufacturing Processes, Test Certificates, Adhesive, And Fasteners.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture.Specification:Material: Fiberglass ( Raw Materials: Fiber Sheets, Resin, Hardner, Fiber Chalk Etc ) Height: 8 Ft. ( Approx. ) ( Attched Image In Annex.I ) 6 Manufacturing, Supply , Installation Of Frp Model Mother With Chield Covered By Artificial Grass At Park Under Buniadpur Municipality.High Quality Finishwith Fire Resistive Resin Coatingand Also Extra Strong Uv-4 Protected Against Fading Withthickness Of 4 Mm.Rate Should Be Included Included All Structural Framing Work By Iron Angle, Plate, Nut And Screw, Welding Work Etc . The Frp Having Density May Be Between 1, 2 G / Cm3 And 2, 0 G / Cm3 Andabout 0.09 Inch In Thickness, Fiber Mass Fraction 60-80%, Fiber Volume Fraction 50-60%, Water Absorption: = 0.2%The Manufacturer / Supplier Shall Provide Full Details Of The Frp Materials, Including All Associated Manufacturing Processes, Test Certificates, Adhesive, And Fasteners.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture.Specification:Material: Fiberglass ( Raw Materials: Fiber Sheets, Resin, Hardner, Fiber Chalk Etc ) Height: 8 Ft. ( Approx. ) ( Attched Image In Annex.I ) 7 Manufacturing, Supplying, And Installing Of Garden Bench 3 Seater For Outside Seating With Cast Iron Leg Support Painted With Spray Paint For Shiny Lookand Seating Material Slats / Strips - 4Mm Thick And Strong Frp ( Fibre-Reinforced Plastic ) Is Strong And Durable Design To Take Load Up To 350 Kg. Distributed Across The Length.Relevant Construction And / Or Structural Drawingsshall Be Submitted To The Eic For Approval In Accordance With The Requirements As Per This Specification.The Manufacturer / Supplier Shall Provide Full Details Of The Frp Materials, Including All Associated Manufacturing Processes, Test Certificates, Adhesive, And Fasteners.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture The Frp Components In Accordance With Any Structural Drawings Provided By The Eic.Dimension=69D X 160W X 88H Centimetersmaterial=Cast Iron, Frp ( Fibre-Reinforced Plastic ) Style = Gardensize=3 Seaterfurniture Finish= Natural Woodseat Height : 16 Inchesitem Weight : Not Less Than 55 Kgwaterproof : Yes ( Attched Image In Annex.I ) 8 Supplyingfitting And Fixing Frp Finished 3D Wall Muralwith Matt Finish, The Thickness Of The Frp Workis Ranges Between 4 Mm To 8 Mm.The Manufacturer / Supplier Shall Provide Full Details Of The Frp Materials, Including All Associated Manufacturing Processes, Test Certificates, Adhesive, And Fasteners.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture The Frp Components In Accordance With Any Structural Drawings Provided By The Eic.Material=Frp ( Fibre-Reinforced Plastic ) Finish- Matt Thickness- 4 Mm To 8 Mm.Length= 4 M , Width= 2.5 Mtrwaterproof : Yes ( Attched Image In Annex.I ) 9 Supplying, And Installing Of Fibre Reinforcedmade Combination Covered With Artificial Grass Of Letter For Theword Buniadpur MunicipalityAt Site With Fire Resistive Resin Coatingand Also Extra Strong Uv-4 Protected Against Fading With Suitable Thickness According To The Height 1800 Mm Rate Should Be Included Included All Structural Framing Work By Iron Angle, Plate, Nut And Screw, Welding Work Etc .The Colour Should Bemade As Per Direction Of Eic.The Manufacturer / Supplier Shall Responsible For All Labour, Materials, Equipment, Carriageand All Other Incidentalscost Governed By This Specification To Manufacture.Height Of The Each Letter Not Less Than 1200 Mmattched Image In Annex.I )