Tender For Replmnt Of Light Fitings,Motors <(>&<)> Dedust Of Panels/Eot Cranes -, ROURKELA-Odisha

Tender For Replmnt Of Light Fitings,Motors <(>&<)> Dedust Of Panels/Eot Cranes -REMOVAL OF DUST,MUCK AND DEBRIS FROM GIRDER, WALK WAYS,LIGHTING BAYS,ALL ELECTRICAL PANELS,MOTORS AND CABINS OF EOT & POT CRANES IN UNIT-I,OXYGEN PLANT JOB AREAS : A) UNIT-I:MAIN COMPRESSOR HALL AREA OF EOT CRANE =350 SQ.M - ONE NO. B)CENTRAL COMPRESSOR STATION(ROLLING MILL ZONE): AREA OF EOT CRANE =300 SQ.M - TWO NOS. JOBS TO BE EXECUTED: (A)REMOVAL OF DUST,MUCK AND DEBRIS FROM GIRDERS, LIGHTING BAY WALK WAYS,HOSPITAL BAY WALK WAYS, LIGHT FITTINGS,STAIRCASE AND FLOOR BELOW CRANES IN COMPRESSOR HALLS. (B)ALL THE DUST AND MUCK TO BE COLLECTED IN SACK WITHOUT SPILLING ON THE SHOP FLOOR. IF ANY DUST ACCUMULATES ON THE SHOPFLOOR ON ACCOUNT OF THIS JOB,THEN THAT DUST IS TO BE REMOVED FROM THE SHOP FLOOR., HOUSEKEEPING & DEDUSTING OF MCC & SWITCHGEAR PANELS AND ROOMS IN UNIT-I,OXYGEN PLANT: HP NITROGEN COMPRESSOR MCC ROOM ,CRGO PUMP HOUSE MCC ROOM,2X60T PROPANE PLANT,CENTRAL COMPRESSOR STATION(ROLLING MILL ZONE). AREA OF MCC & CONTROL ROOM: AREA OF MCC ROOM OF HP NITROGEN COMPRESSOR = 200 SQ.M (APPROX.) AREA OF MCC ROOM OF CRGO PUMP HOUSE = 200 SQ.M (AAPROX.) AREA OF MCC & CONTROL ROOM OF CENTRAL AIR COMPRESSOR STATION (ROLLING MILL ZONE) = 500 SQ.M (APPROX.) AREA OF MCC & CONTROL ROOM OF 2X60T PROPANE PLANT = 200 SQ.M (APPROX.) JOBS TO BE EXECUTED: (A)REMOVAL OF DUST,MUCK FROM MCC & SWITCHGEAR PANELS,PLACEMENT OF RUBBER MATS AFTER THOROUGH DEDUSTING OF MCC & SWITCHGEAR ROOMS. (B)ALL THE DUST,MUCK & DEBRIS TO BE COLLECTED IN SACK WITHOUT SPILLING ON THE FLOOR.DUST ACCUMULATED ON THE FLOOR ON ACCOUNT OF THIS JOB IS TO BE REMOVED FROM THE FLOOR OF MCC & SWITCHGEAR ROOMS. (C)FILLED SACK BAGS TO BE DISPOSED OFF OUTSIDE OXYGEN PLANT BATTERY LIMIT IN THS SPECIFIED AREA AS PER THE INSTRUCTION OF EXECUTING OFFICER., REPAIR AND REPLACEMENT OF LIGHT FITTINGS TO MAINTAIN ILLUMINATION. THE JOB INCLUDES: (A)REPLACEMENT OF DEFECTIVE LAMPS,HOLDERS,FITTINGS,CABLE,CONNECTORS & ANY OTHER COMPONENTS. (B)CHECKING OF CIRCUIT,CONNECTIONS AND RECTIFICATION,IF REQUIRED. (C)CLEANING OF TRANSPARENT COVERS AND REPLACEMENT OF DAMAGED COVER,IF REQUIRED. (D)TESTING OF FITTINGS. (E)INSTALLATION OF NEW FITTINGS. (F)TEMPORARY FITTINGS TO BE REPLACED WITH NEW FITTINGS. (G)MODIFICATION OF EXISTING LIGHT FITTINGS AND LIGHTING CIRCUIT. (H)UNWANTED LIGHTING CABLES TO BE REMOVED & HANGING CABLES TO BE DRESSED. (I)REPAIR/MODIFICATION IN EMERGENCY LIGHTING SYSTEM, REMOVAL AND FIXING BACK OF LT MOTORS THE JOB INCLUDES : (A)REMOVAL OF FOUNDATION BOLTS AND EARTH CONNECTIONS. (B)REMOVAL OF POWER AND CONTROL CABLES CONNECTED IN MAIN AND AUXILIARY TERMINAL BOXES OF MOTOR AFTER PROPER MARKING AND NOTING ALL CONNECTIONS. PVC TAPE IS TO BE APPLIED ON THE EXPOSED TERMINALS OF POWER AND CONTROL CABLES. (C)REMOVAL OF MOTOR FROM MOTOR FOUNDATION AND SHIFTING TO STORAGE AREA SPECIFIED BY AREA-IN CHARGE. (D)LOADING OF MOTOR IN TRUCK AND SHIFTING OF MOTOR TO REPAIR SHOP (ELECTRICAL) FOR OVERHAULING.TRUCK SHALL BE PROVIDED BY RSP. (E)COLLECTION OF MOTOR FROM REPAIR SHOP(ELECTRICAL) AFTER OVERHAULING IN TRUCK (PROVIDED BY RSP) (F)UNLOADING OF MOTOR FROM TRUCK AND SHIFTING TO SPECIFIED AREA FOR STORAGE. (G)SHIFTING OF MOTOR TO MOTOR FOUNDATION. (H)CONNECTION OF POWER AND CONTROL CABLES AFTER ALIGNMENT, etc.

Refer document

Refer document