Construction Of Sub Health Center At Bhinmal Chak, Block Bhinmal, District Jalore.
Tender Value
37 Lakhs
Estimated cost
Bid Submission
04 May 2022
0 days left
EMD
74000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bhinmal → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Sub Health Center At Bhinmal Chak, Block Bhinmal, District Jalore.
BOQ
| Sl. No. | Item Description |
| 1 | PART (A) :CIVIL WORK Earth work in surface excavation not exceeding 30 Cm. In depth but exceeding 1.5 meter in width as well as 10 Sam. on plan including disposal of excavated earth up to 50 Mtr. And lift up to 1.5 Mtr. Disposed soil to be leveled and neatly dressed : All kinds of soil. |
| 2 | Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 Mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter.All kinds of soil. |
| 3 | Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering All up to plinth level 1:4:8 (1Cement :4 Course Sand :8 Graded stone aggregate 40 mm nominal size (Crusher Broken) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth , consolidatingeach deposited layer by ramming and watering including lead upto 50Mtr. and lift upto 1.5Mtr. |
| 5 | Random Rubble stone masonary for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall in : Cement Mortar 1:6 (1-Cement:6-Sand). |
| 6 | Random Rubble stone masonary for superstructure above plinth level one storey height above 30 Cm. thick walls in : Cement Mortar 1:6 (1-Cement:6-Sand). |
| 7 | Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways and removal of formwork for foundations in basements rafts, footings, strap beams, bases of columns , etc. up to plinth level. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete including curing compaction finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement.All work up to plinth level : R.C.C grade M20 |
| 9 | Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members andremoval of formwork for superstructure up to 4.5 mtr aboveplinth,for: Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs, girders having slopes up to 15o , landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases, up to floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good and joints excluding the cost of centering, shuttering and reinforcement R.C.C grade M20 |
| 11 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Tremo Mechanically treated bars |
| 12 | Half brick masonry in superstructure up to third story using bricks of designation 75 with nominal hoop reinforced (2 Nos. 6mm MS bar) at every fourth course inCement mortar 1:4 (1-Cement:4-coarse sand).(600+27=627) |
| 13 | Providing and fixing pressed steel mitred door frames manufactured from commercial mild steel sheet of 1.25 mm (16 gauge) thickness including hinges jamb, lock jamb, head and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Profile \"B\" |
| 14 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure ‘A’ Decorative Teak veener both side 30 mm thick shutter |
| 15 | Add extra for Flush doors For Internal teak wood lipping in 25 mm depth in Single leaf. |
| 16 | Add extra for Flush doors For Internal teak wood lipping in 25 mm depth in Double leaf. |
| 17 | Add extra for Flush doors For double leaf shutter |
| 18 | Supplying and fixing of Steel windows made out (65x40mm), hollow metal pressed section of 1.25 mm thick sheet F4 & F7 standard rolled section conforming to IS 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening C.R. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidized steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square M.S. bars 10 Cm. C/C and applying priming coat of red oxide paint. |
| 19 | Supplying and fixing fixed wire gauge of Stainless steel of 14 mesh x 24 gauge to the aliminum window by aluminum beadind 20 x3mm with suitable screws at not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 20 | Renewing glass panes, with puty and nails wherever necessary:4 mm thick plain glass panes. |
| 21 | Grading roof water proofing treatment with : Cement concrete 1:2:4 (1-Cement:2-coarse sand :4-graded stone aggregate 20mm nominal size). |
| 22 | Providing and laying 20 to 25 mm size glazed tiles pieces for rooof treatment having colour and shade as approved by the Engineer incharge over 25 mm thick layer of cement mortar mix 1:4 with application of cement slurry including finishing of joints with ordinary cement and curing etc. complete in all respect. Washing with acid. |
| 23 | Providing batta (gola) 75mm x 75mm in cement concrete (1:2:4) including finished with cement mortar 1:3 as per standard design. |
| 24 | Providing & laying vitrified Porcelain dianomite floor tile, skirting, dedo, (Johnso, Euro, Naveen, Bell,Marbito or equivalent etc.) size 600x600, 10 mm thick flooring over 20 mm thick bed mortar 1:4 mix with 2-3 mm thick joint to be filled with cementious grout or polymer based non shrink grout make Rofee/ Bell adhesive/ pidite etc of matching colour as per requirement of site. |
| 25 | Providing and fixing Ist quality standard White Ivory straight edge Glazed Tiles ISI marked [IS:13753] (Kajariya, Jhonson, Somani make etc. ) of size 450mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). |
| 26 | Polished Blue Kota Stone flooring skirting, laid over 20 mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : For area of each slab up to 2001 to 5000Sq. Cm :(A) 25 mm thick slab. |
| 27 | Supplying and fixing machine cut and polished stone shelves, tands and sills in CM 1:3 with machine cut edges: Kota stone 25 to 30 mm thick. |
| 28 | Providing and fixing Ist quality MAT finished ceremic tile size 400x400mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slsurry including nicely finished joints using water proof joint filler power (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster).(779+64) = 843 |
| 29 | Add extra for floor work due to extra cost of cement mortar 1:4 (1-Cement:4- fine sand) 20 mm thick. |
| 30 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished:20mm thick. |
| 31 | Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete : 50mm thick with 20 mm thick nominal size aggregate. |
| 32 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 33 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 34 | Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: New work |
| 35 | Providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. |
| 36 | Painting with enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work. |
| 37 | Providing and 30mm thick Rajshri Brand Factory made Solid Panel PVC Door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm for stiles & 15mmx15mm for top and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat moulded \"Rajshri\" PVC \"C\" Channel of size 30x50mm forming stiles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail and bottom rail on either side, & 10mm (5mmx2) thick, 20mm wide cross PVC sheets as gap insert for top rail & bottom rail.Providing and 30mm thick Rajshri Brand Factory made Solid Panel PVC Door shutter consisting of frame mPanelling of 5mm thick PVC sheet to be fitted in the M.S. Frame welded/sealed to the stiles & rail with 30mm wide x 5mm thick PVC sheet beading on either side and joined together with solvent cement adhesive. An additional 5mm thick PVC strip o f 20mm width is to be stuck on the interior side of \"C\" Channel using PVC solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer\"s specification & drawing (For W.C. & Bathroom shutters). |
| 38 | Providing and fixing Granite stone slab mirror polished and machine edge cut in Walls, Pillars, Steps, Shelves, Sills, Counters. Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing of: Jhansi (Red / Choclate Colour) Size above 3600 Cm2 |
| 39 | P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant 110mm dia |
| 40 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: a) Bend 87.5110mm |
| 41 | b) Pipe clip 110mm |
| 42 | Providing & laying Chequerred terrazzo tiles of approved make 22 mm thick with marble chips of size upto 6mm, in floors, jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28 mm thick bed of C.M. 1:4 Light shade using white cement. Add extra for chequerred coloured plain cement concrete or specially manufactured non-slipping tiles of approved make 20 mm thick. (504+31) = 535 |
| 43 | Providing & fixing ms sheet single leaf door shutters in angle iron frame 35x35x5 mm suitablly diagonally braced with 25x3mm flat ironabove and below lock rail of size 50x5 mm beading extra includingall fittings, as per direction of engg. incharge but excluding coes of chokhats including two coats of anti corrastie red oxide primer panit. MS sheet 18 SWG |
| 44 | Supply & fixing of stainless steel pipe railing for ramp railing height, 90 cm. with 40 mm dia stainless steel pipe with 18 gauge with drop (vertical post) at 90 cm. C/C and intermidiate horizontal pipe with suitable height of same size and gauge with coupling, grinding and polishing & fix of master pieces as per required point as per approved design of Engineer incharge. |
| 45 | Cutting & moulding by hand power grinder including polishing etc. complete in all type of Kota/ Marble/ Granite/ Jodhpur stone etc. 25 mm. |
| 46 | Making grooves as per design in plaster 10mm to 20mm wide. |
| 47 | P & F Indian type white glazed vitreous china Ist quality W.C. orissa pan (IS:2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor : Size Size 580x440 mm. |
| 48 | P & F European type white glazed vitreous china Ist quality W.C. pan (IS:2556 Mark) with P or S trap including cutting and making good the wall and floor. |
| 49 | P & F water closet Seat Covers with brass hinges complete : Solid PVC (ISI marked) grade-I White for EWC. |
| 50 | P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall :PVC with PVC bend as per IS : 7231 |
| 51 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : Size 550mm x 400mm |
| 52 | 460 dia for counter top. |
| 53 | P & F kitchen & Lab Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up to floor level complete including cutting and making good the wall & floor :1.0mm thick salem stainless steel AISI -304 kitchen sink of approved make (Nirali, Neel- Kanth, Jaina, Faber, Cryistal) with large waste coupling.Size 24x18x8 |
| 54 | P&F looking mirrors with PVC frame of approved (atul/equivalent) Size 500x400mm |
| 55 | P&F towel rail or ring of approved quality /make: C.P. brass Towel rail elbow type with concealed screws size 600mm (heavy duty) |
| 56 | Providing and fiixng C.P. flange for 15mm dia tap.s |
| 57 | P & F G.I. Pipes (Internal work) with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors : (A) Exposed on wall a) 15 mm dia nominal bore. B-Class |
| 58 | b) 25 mm dia nominal bore B-Class |
| 59 | P & F G.I. Pipes (External work) with G.I. fittings (IS:1239 Mark) including trenching & refilling earth etc. \"B\" Class a) 15mm dia nominal bore. |
| 60 | b) 25 mm dia nominal bore. |
| 61 | P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : a) C.P. Brass bib cock, 15 mm nominal bore. |
| 62 | b) Long body, 15 mm nominal bore weight not less than 690 gm.B628 |
| 63 | c)Elbow action, 15 mm nominal bore. |
| 64 | P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete : Brass wt. 400 gm, 15 mm. |
| 65 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked). |
| 66 | P & F 15 mm. Dia Connection pipe of approved quality/make: PVC pipe with C.P. Brass nuts up to length 450 mm. |
| 67 | P & F Full-way valve (IS:778 Mark) or wheel valve of approved make : a) Gun-metal 15 mm nominal bore. |
| 68 | b) Gun-metal 25 mm nominal bore. |
| 69 | P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. a) 500 litres capacity. |
| 70 | Hoisting Charges for each floor : a) 500 litres capacity. |
| 71 | P & F Square-mouth gully trap `A` grade (IS :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type. Trap size 150 X 100mm, 7.2 Kg. C.I. cover with frame, Internal Chamber size 300 X 300mm. |
| 72 | Construction of manhole in all type of soil inner size 90 X 60 Cm. thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring,making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C.flooring , 25 Kg. CI cover with frame of 40mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth upto 0.5mtr |
| 73 | Construction of chamber in all type of soil with 300 mm thick masonry in Cm 1:6 m 100mm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 300x300mm depth upto 0.5m & 5Kg C.I. cover with frame |
| 74 | Construction of soakage well in all type of soil 300 mm thick dry masonry top and bottom 300 mm course in CM 1:6, 80 mm thick stone slab, jointing of slab in CM 1:3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring, earth work complete as per approved drawing including disposal of earth within a lead of 50 mtr. : Size 300 Cm. dia outside & 300 Cm. depth. |
| 75 | Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B\" for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. a) 75mm dia |
| 76 | b) 110mm dia |
| 77 | Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B\" for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. a) Bend 87.5 Dg. 75mm dia. |
| 78 | b) Bend 87.5 Dg. 110mm dia. |
| 79 | c) Door Bend 87.5Dg. 110mm dia. |
| 80 | d) Nahni Trap with Jali 4\"110mm dia |
| 81 | e) Vent Cowel 75mm dia. |
| 82 | P&F Jet spray for water closet with C.P. copper tube flange of approved make |
| 83 | PART (B) :BRANDING WORK - Making of Health Wellness Centre pattern (Gola) including colour picture work inside for façade branding incl. material, labour & T&P as per direction of Engineer-in-charge. |
| 84 | Designing, Developing, Providing and fixing of Acrylic Sandwich way signage\"s in different building. The various different sized signage\"s like building directory, facilities, Room Nos. etc. are made out of A grade Acast or equivalent brand 5mm thick transparent acrylic sheet at back and 3mm thick on front side. The eco-print on 3M IJ 15-10 monomeric calandared Vinyl film sheet of approved colour pattern and shade is sandwich between two acrylic sheets with required number and size of stainless steel studs and fittings. The outer edges are tapered and finished smooth. The developer has to design the signage\"s for different buildings as per requirement of the client and got the design and sample approved from competent authority before going in to actual execution at site. Basic data for clients requirement would be provided by the department. |
| 85 | PART C:ELECTRIC WORKS - Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it\"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal, 6 A switch , 3 pin ceiling rose/ Lamp holder / 3 point Connector, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required.Short point (up to 3 mtr.) |
| 86 | Medium point (up to 6 mtr.) |
| 87 | Long point(up to 10 mtr..) |
| 88 | Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & it\"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size,6 Aswitch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. On board |
| 89 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge.MMS ( IS:9537 P - III ) PVC conduit 25 mm |
| 90 | 32 mm |
| 91 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existingsurface or recessed PVC/ MS conduit/casing capping includingall as per pre approved by Engineer in charge,making connections, etc. as required. 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 92 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 93 | 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. |
| 94 | Providing and fixing ofnon modular power plug point accessories as per PWD specification for electrical Works with18 SWG G Ibox of size 175 x 100 x 60 mm with earthing terminal/connector onrecessed/surface with suitable size phenolic laminated sheet (IS : 2036 -1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet[ as per detailed in respective item in BSR], making connection , testing , etc. as required.All as per pre approved by Engineer in charge. |
| 95 | Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding making connections, testing etc. as required.. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.Single pole MCB 6 A to 32 A rating |
| 96 | Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , IP 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. Double pole Isolator 30 A / 40 A rating |
| 97 | Four pole Isolator 63 A rating |
| 98 | Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickDistribution board as per PWD specificationfor electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DBterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.IP-43 Double door (single phase) 4 Way (4 O/G +2 I/C ) |
| 99 | IP-43 Double door (Three phase) 6 Way ( 18 O/G + 8 I/C ) |
| 100 | Providing & Fixing ofISI marked (IS:371) 6 amp surface type 3 pin ceiling roses as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. |
| 101 | Providing & Fixing of ISI marked (IS:1258)6 ampbatten/angle lampholder as per PWD specification for electrical Works,made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. All as per pre approved by Engineer in charge. |
| 102 | Providing & Fixing of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per PWD specification for electrical Works, ISI marked (IS:11037) made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required. |
| 103 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armouredaluminiumcable of 1.1 KV grade as per PWD specification for electrical Worksin existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below:- |
| 104 | (a) Material :- H4- Gradealuminium conductor of purity >99.6 %& as perIS:1554 P-I / IS :7098 P - I |
| 105 | (b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures . |
| 106 | (c)OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities forcables . Appropriate type test certificate / OEM test report shall be submitted .All above as per pre approved by Engineer in charge.For additional technical parameters of products/ work |
| 107 | 16.0 Sq. mm 4 core |
| 108 | SITC ofchemical Gel earthing system ofDual Pipe Technology made of with \"B\" ClassG I Pipeas per IS 1239 ( part-1):2004of Medium duty of following sizesas per points mentioned (a), (b), [c), (d), (e) below :- |
| 109 | (a) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, CPRI/ ERDAtested with RMS capacity of minimum 35- 40 KA for withstanding 1 second . |
| 110 | (b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated labfor lowresistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major contentas per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts |
| 111 | ©Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. |
| 112 | (d)Testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. |
| 113 | (e) Self certificate for confirming above standards from OEM is mandatory. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 114 | With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewell |
| 115 | GI pipe 2000 mm long, 50 / 25mm, Terminal 12 mm GI Strip |
| 116 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cuthimble etc. as required.All as per pre approved by Engineer in charge. 8 SWG G.I. ( Hot Dipped) Wire |
| 117 | Providing & Fixing of ISO Certified company made BEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanas per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge.1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 118 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, Power Consumption of18W/20W ,system lumen efficacy = 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.=0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge .4\" LED Tube shape fixture 18/20 W (Polycarbonate Base) |
| 119 | Providing & Fixing ofof Double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. OEM shall be an ISO certified company.Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge.300 mm sweep |
| 120 | Providing & Fixing ofextra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.All as per pre approved by Engineer in charge. |
| 121 | Supply Installation testing & Commissioning of ISO certified manufacturer madeMonoblock motor pump set ISI marked (IS:9079-2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, . Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.1.0 HP, 1-Ø, (10-120)Mtr, (30-12) LPM |
| 122 | P & F 18 swgM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge. |
| 123 | Supply & Fixing of ABC Type (MAP 50)type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, withDry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. OEM will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket includinginitial fill and wall suspension complete in all respect. Serial no. and date of manufacturing should be embossed or printedon the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge.. 6 kg |
| 124 | Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wtwith High Power LEDs is to be usedand potted driver must be potted & has a unique BIS R number withInput Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driverEfficiency >85%,THD(I) <10%Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <1000mA shown in LM79 report. The luminaireshall be BIS certified and T.C. certified. Life ExpectancyEqual or more than 50000 burning hrs with Minimum 70% lumen maintened ,color Rendering Index >70 and CCT 5700K +355K. Surge protection shall be min = 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs.Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced. |
| 125 | OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge.LED Street Light fixture 70 Watt |
| 126 | Providing & Fixing of Street light bracket made out from following size of \" B \" class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. All as per pre approved by Engineer in charge.32 mm Dia. |
| 127 | P & F 18 swgM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge. |
| 128 | Providing & FOixing ofISCertified company made ISI marked (IS:2082)of5starrated verticalstoragewaterheaterwith outercasingmadeofM.S.sheetfinishedwithanti-corrosive powdercoating,innertankmadeofpureelectrolytic copper/stainlesssteel/SPHP,Tubularcoppersheathedand Nickel plated heating element/ twin ceremic cartridge heating element, stem type thermostat and thermal cut out, Dual indicating lamps for power supply and thermostat, PUF insulation, Pressure release valve,fusible plug etc. as required heldinpositionwith4no.ragbolts,dulywiredwith3core 2.5/4.0SqmmPVCinsulated&sheathedcopperconductor and16A/25AthreepinplugtopwithPortableResidual Current Device ( PRCD ) facility form OEM,including making inlet,outletheavygaugeC.P./Flexiblealloy connection,testingetc.completeinallrespect.Appropriate OEMtest certificate shallbe submittedby contractor.Allas per pre approved byEngineer in charge. 25 Ltr. |
| 129 | P & F of Gravity Louver shutter of superior quality made outofframeof 18swgM.S.sheet&Louversmade from 24 swg MS Sheetwith enamel paint including cost of nuts, bolts, etc as reqd.Appropriate OEM test certificateshallbesubmittedbycontractor.Allasper preapprovedbyEngineerincharge. Up to 380 mm size |
| 130 | Providing & Fixing of paper phenolic resin bondedlaminatesconfirmingtoIS:2036- 1995forboxes/ framesincludingmakingholesforswitchesetc,with brass/zincplatedscrews,washers, nutandboltsas required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .6.4 mm thick |
| 131 | Making of hole in wall (brick/stone) of required size forhousingexhaustfanandmakinggoodthesame,with cement plaster as required of following size: Up to 457 mm size |
| 132 | Providing&FixingofIP40LEDSurface/Recessed/suspendedmounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowishdiffuserforuniformlightdistribution.Hficigiehnceyfwith 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protectionandincomplianceto IECstandards(Integralwithlight fixture).Systemlumenefficacyof= 120lm/Watt,THD<10%, p.f.=0.95,CRI>80, lifetimeofminimum 50000BurningHours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K /5700°K/6000°K/6500°K(AsperANSIBin),maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). ManufacturesWordMark/NameEngraved/Embossing/Screenprinting onhousing. 36W LED light fixture 2\"x2\" with acrylic / prismatic front cover. |
| 133 | Providing&Fixingofenergyefficient/energysavingIP20LED directretrofitBulb inexistingholderorfixtureasrequiredwith systemlumenefficacy=100lm/Wattoutput,pf0.95,CRI>70, minimum life time of minimum2u5rn0i0n0g BHourswith , 70% of intialLumenmaintanedtilllifeends ,CCT3000°K/4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). ManufacturesWordMark/NameEngraved/Embossing/Screen printing onhousing.9 Watt |
| 134 | Providing&Fixingof ISImarked (IS:2268-1994)dingdong/musical chime bell as per PWD specification for electrical Works,includingmakingconnectiontestingetc.asrequired. All as per pre approved by Engineer in charge. |
AI Tender Summary
Tender Timeline
Apr 28, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMay 04, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMay 05, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender