Construction Panchayat Community Centre Panchayat Ghar In Gram Panchayat Khodri Block Poanta Sahib Distt Sirmour As Per Dnit
Tender Value
32.59 Lakhs
Estimated cost
Bid Submission
04 May 2022
0 days left
EMD
56500
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
khodri → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Panchayat Community Centre Panchayat Ghar In Gram Panchayat Khodri Block Poanta Sahib Distt Sirmour As Per Dnit
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, asdirected by Engineer-in-charge. All kinds of soil as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out theexcavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for : as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 7 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 8 | Suspended floors, roofs, landings, balconies and access platform |
| 9 | Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10 (1 cement : 5 coarse sand): 10graded stone aggregate 40 mm nominal size) : but including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 11 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) but including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge |
| 12 | All work up to plinth level : |
| 13 | In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up tofloor five level |
| 14 | In beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, |
| 15 | Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto floor two level. |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete .Thermo-Mechanically Treated bars of grade Fe-500D or more.including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 17 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 18 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 19 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarsesand)including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 20 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal woodincluding all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 21 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 22 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Kiln seasoned and chemically treated hollock wood 35 mm thickincluding all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 23 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws ncluding all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 24 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). ncluding all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge. |
| 25 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 26 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 27 | 250x16mm |
| 28 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 29 | 200x10mm |
| 30 | 100x10mm |
| 31 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 32 | 125mm |
| 33 | 100mm |
| 34 | Providing and fixing aluminium casement stays,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 36 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Tile Size 600x600 mm as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 37 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete. |
| 38 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stoneaggregate as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 39 | Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 40 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 41 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 42 | 15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 coarse sand) as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 43 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 44 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 45 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and includingpriming coat of exterior primer applied @ 0.90 litre/10 sqm. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 46 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 47 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 48 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, includingflush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 49 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P.brass pillar tap as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 50 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:893115 mm nominal bore as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 51 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 52 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore15 mm nominal bore as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 53 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end25 mm nominal bor as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 54 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 250 as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 55 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 56 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 57 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 58 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : |
| 59 | 15 mm (fifteen millimeters) nominal bore |
| 60 | 20 mm (twenty millimeters) nominal bore |
| 61 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 62 | 15 mm (fifteen millimeters) nominal bore |
| 63 | 20 mm (twenty millimeters) nominal bore |
| 64 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : |
| 65 | 15 mm (fifteen millimeters) nominal bore |
| 66 | 20 mm (twenty millimeters) nominal bore |
| 67 | Providing and fixing required GI /Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. |
| 68 | Coupling/Socket 15 mm Dia |
| 69 | Coupling/Socket 20 mm Dia |
| 70 | Slip Coupling/ Socket 15 mm Dia |
| 71 | Slip Coupling/ Socket20 mm Dia |
| 72 | Elbow 90° 15 mm Dia |
| 73 | Elbow 90° 20 mm Dia |
| 74 | Equal Tee 15 mm Dia |
| 75 | Equal Tee 15 20 mm Dia |
| 76 | Providing and fixing PVC water storage tank of Sintex or equvalent make of ISI :12701 Marked ,G.I. inlet and outlet connection , 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground Level (1000 litres net capacity tank)including carriage of material upto all leads and lifts in all floor as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 77 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 78 | 75 mm nominal size (seventy five millimeters) size |
| 79 | 110 mm nominal size (one hundredten millimeters) size |
| 80 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 81 | Coupler 75 mm |
| 82 | Coupler 110 mm |
| 83 | Bend 87.5°75 mm |
| 84 | Bend 87.5°110 mm |
| 85 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 455x610 mm and 45 cm deep for single pipe line : 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 86 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 87 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved qualityRectangular shape 600x450 mm internal dimensions as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 88 | Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete. as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . |
| 89 | Wiring for light point / fanpoint /exhaust fan /call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. |
| 90 | Group C. |
| 91 | Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit, with 2-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. |
| 92 | Group C. |
| 93 | Providing and installation of surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with minimum 2 year warrantysuitable for input voltage: 220-240 V, 50/60 Hz, complete with all accesories, including mounting clips & loop in loop out wire, connections, testing and commissioning etc. as required, Make: Twinkle, Syska, Philips , Havells, Bajaj, Panasonic or any other approved by Engineer-in-Charge. |
| 94 | LED Batten Light 20 Watt. (length 4 Feet) |
| 95 | Providing and installation of following type of Surface/Recess mounting round/Square LED Downlight with AL die-cast body, finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation suitable for input voltage: AC 220-240 V, 50/60Hz, complete with all accessories, including making connections, testing and commissioning etc. as required. Make: Philips, Twinkle, GE, Syska or any other approved by Engineer-in-Charge. |
| 96 | LED Downlight6 WH |
| 97 | Providing and installation of following type of Surface/Recess mounting Square type LED Panel Light, powder coated housing made of CRCA sheet, suitable for input voltage: AC 220-240 V, 50/60Hz, complete with all accessories, including making connections, testing and commissioning etc. as required. Make: Twinkle, Havell\"s Bajaj, Syska Panasonic or any other approved by Engineer-in-Charge. |
| 98 | LED Panel Light 36 Watt. (Size:- 2\" x 2\" feet) |
| 99 | Providing and installation of following type of Fress Air Ventilating fan Non-metallic range with lower Shutter of following sizes in the existing opening, including making the hole to suit the size of the fan, making good the damages, connections, testing and commissioning etc. as required Make: Havells, Khaitan, Bajaj, Crompton, Standard or any other approved by Engineer-in-Charge. |
| 100 | Fress Air Ventilating fan 250 mm sweep |
| 101 | Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:- |
| 102 | Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required. |
| 103 | Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required. |
| 104 | Supplying and fixing electrical switch board, having 4 No. of 5/6 amp. Modular Switches and Modular Socket on suitable size of G.I. modular boxes of 12 modules (205mmx135mmx60mm) deep( nominal size) on surface or in recess with suitable size along with modular base and cover platefor modular switches in the front including providing and fixing4 No. 5 pin 5/6 amp modular socket outlet and 5/6 ampmodular switch, connection, painting etc.as required.(For Light Plug/Computer Points) |
| 105 | Supplyinganderection of 6amps. to 32 amps. rating, 10 KA breaking capacity, 240volts, \"C\" curves, miniaturecircuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- |
| 106 | Single pole 6 Amp. Cat-A. |
| 107 | Single pole 16 Amp. Cat-A. |
| 108 | Supplyinganderection of 40/50/63 amps rating, 10 KA breaking capacity, 240volts, \"C\" curves, miniaturecircuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- |
| 109 | Double pole. 63 Amp. Cat-A. |
| 110 | Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 111 | 63 Amps. Cat-A. |
| 112 | Supplyingand fixingoffollowingway, singlepoleandneutral sheetsteel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- |
| 113 | Double door-16 way |
| 114 | Double door 8-way |
| 115 | Providing,installation,testing and commissioning of ceiling fan with regulator including wiring the down rod of standard length(upto 30 cm with 16/0.20 mm twin twisted flexible cotton braded copper cable including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required |
| 116 | Ceiling Fan 1400mm sweep, Category-A |
| 117 | Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. |
| 118 | 2x1.5 Sq. mm. |
| 119 | 2x2.5 Sq. mm. |
| 120 | 2x10 Sq. mm. |
| 121 | Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required. |
| 122 | Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required. |
| 123 | Supplying and laying 6 SWG G.I wire at 0.50 mtr below ground level for earth electrode conductor including soldering etc. as required. |
| 124 | Earthing with G.I earth pipe 4.5 mtr long and 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangment with watering pipe etc. (but without charcol or coke and salt) Complete as required |
| 125 | Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required. |
AI Tender Summary
Tender Timeline
Apr 27, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMay 04, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMay 05, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender