Military Engineer Services-MES has published Repair To Flooring Masonry Joinery Plumbing Water Supply Fittings Glass Panes Water Tank In Md Jco / Or Accn Incl ( Fafa Accn ) At Y Stn Under Ge Satwari. Submission Date for this Tender is 21-05-2022. Masonary Work Tenders in satwari Jammu And Kashmir. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 07-May-2022 | Amendment in BOQ | BOQ | 14-05-2022 |
| 2 | 14-May-2022 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 21-05-2022 |
| Sl. No. | Item Description |
| 1 | Note :- 1.Work will be carried out upto 4th storey of bldgs also as per direction of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. 2.Contractor should also resolve the day to day problems/ complaint related to item of BOQ in piece meal as per requirement and give the feedback to the Engr-in-charge within next 24 hours about the work done and complete site will not be vacated for the same, only requirement basis site for work will be handed over and work will be carried out up to 4th storey. 3. The contractor shall be provided with space for setting up maintenance cell at the specified location as per the directions of engineer in charge which shalled be manned by the supervisor responsible for collecting complaints from the concerned JE/AGE. However, no additional payment other than those measurable below shall be made to the contractor. The recovery for non-complaince shall be made as per provisions given in Sch "A" notes. |
| 2 | Supply and fixing in repair, brass face for CP/Brass Bib tap, Angle/Stop cock, Pillar cock, wall mixer, WHB mixer, etcfor 15 mm bore pipecomplete all as specified and as directed by Engineer-in-charge. |
| 3 | Supply and fixing in repair, brass jumper washer for CP/Brass Bib tap, Angle/stop cock, Pillar cock, wall mixer, WHB mixer, etc , for 15 mm bore pipecomplete all as specified and as directed by Engineer-in-charge. |
| 4 | Supply and fixing in repair, PVC Knob or flushing handle for flushing cistern of capacity 10.0 litres , complete all as specified and as directed by Engineer-in-charge. (Sample as approved & kept in GE"s sample room) |
| 5 | Supply and fixing in repair, PVC float valve suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by Engineer-in-charge. (Sample as approved & kept in GE"s sample room). |
| 6 | Supply and fixing in repair, PVC syphonic kit for flushing cistern of capacity 10.0 litres,complete all as specified and as directed by Engineer-in-charge. (sample as approved & kept in GE"s sample room) |
| 7 | Supply and fixing in repair,PVC bend suitable for flushing cistern of capacity 10.0 litres,complete all as specified and as directed by Engineer-in-charge. (Sample as approved & kept in GE"s sample room). |
| 8 | Supply and fix ing in repair, PVC syphon washer suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by Engineer-in-charge. (Sample as approved & kept in GE"s sample room) |
| 9 | Repairs to steel window, ventilators of any size to make it functional (including slot pin, hinge, hook and eye of standard quality where required), resecuring of windows wire gauge and railings/grills by using welding equipments, complete all as directed. |
| 10 | Repair/ easing ofwooden door any type, glazed or panelled, by trimming the side of door shutter where rubbing with chowkhat, unscrew the hinges screws and lift the door and fix with screws, tightening of wire mesh etc all as per Engr-In-Charge. |
| 11 | Taking down shutters of any description n.exc 1.00 Sqmeach and removing from the site all as specified & directed. |
| 12 | Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site all as specified & directed. |
| 13 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 Sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd. |
| 14 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.5 Sqm but n exc 4.0 sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd. |
| 15 | S&F pressed steel framesof size 125mm x 60mm made outof size 1.25mm thick MS sheet for doorssingle rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 includingPCC 1:3:6 as in back fill to chowkats all as Specified. |
| 16 | S&F pressed steel framesof size 105mm x 60mm made outof size 1.25mm thick MS sheet for doorsdouble rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 includingPCC 1:3:6 as in back fill to chowkats all as Specified. |
| 17 | Supply and fixing Factory made, plain framed, panelled shutter (two Panel) 35mm thick,2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated complete all as directed by Engr-in-Charge. |
| 18 | Supply and fixing 35mm thick2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitredand rebatedsash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a)complete all as specified |
| 19 | S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. Note :- Sampel approved by Engr-in-Charge or GE. |
| 20 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all asspecified and as directed by Engr-in-Charge. |
| 21 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplyingand fixing in the frame at site as per specification & drawing complete all asspecified and as directed by Engr-in-Charge. |
| 22 | S&F Factory made solid PVC Moulded door shutter.28 to 30 mm thick (Stiles) with particle board core with 2, 4 ,or 6 raised panel design with 2 mm thick mouldedPrelam PVC sheet on the front face & 2 mmPrelam PVC sheet on back face, to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the framme at site as per specification and drawing, complete all asspecified and as directed by Engr-in-Charge. |
| 23 | Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed. Note: For measurement superficial area in elevation shall be measured. |
| 24 | M&L 18 mm thick PVC board one side UV printed designing and back side plain colour printed for cub board boxes or kitchen cabinet with shelf, drawer, shutter and frame full size fitted under cooking platform and other platform including fittings etc complete all as specified and directed. |
| 25 | M&L Pressed steel cup board frameof MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats includingbutt hinges 100 mm long. Piano hinges measured separately. |
| 26 | M&L Prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all asspecified and as directed by Engr-in-Charge. |
| 27 | S&F 100mm size Stainless steel handle complete all as specified and as directed. |
| 28 | S&F in repair continuous (piano) hinges,Width of flaps (when open) 30 mmheavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( ISI Marked) |
| 29 | S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified. |
| 30 | Supply and fixingfor stainless steel Butt hinges, 100mm , complete all as specified and as directed |
| 31 | S&F Aluminium anodised, barrel tower boltssize 150 mm of extruded section and fixed complete all as specified. (ISI Marked) |
| 32 | S&F Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified. (ISI Marked) |
| 33 | S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mmwith hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 34 | S & F hasp & staple safety type aluminium anodised with mild steel hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length. |
| 35 | S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 36 | M&L for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed. |
| 37 | S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( ISI Marked) |
| 38 | S&F in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified. |
| 39 | Supply and fixing in repair mild steelhelical ordinaryrat tail rod patternsprings300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed. |
| 40 | S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finialsfor 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings) |
| 41 | Material & labourfactory made steel windows double shutter box type, outer frame made out of ERW TUBE "P" section(60x45x25mm) and shutters of ERW TUBE "P" section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of "Z" section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge.NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs. |
| 42 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 43 | Ditto as per item no 42 but in ventilators any size |
| 44 | Hacking out old broken glass (any thickness,size quality or description) from any types of wooden/steel/alum (up to 4th storey) frames or stone concrete or brick surrounds glazed with putty or fixed with beads. |
| 45 | S&F 4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (uptofourth storey with necessary scaffolding), all as specified. |
| 46 | S&F 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (uptofourth storey with necessary scaffolding), all as specified. |
| 47 | Securing glass of any description in existing wooden and iron frames glazed with putty/beads including removing loose or decayed putty/beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work ( New length of frame reputtied shall be measured. |
| 48 | Supply and fixing Galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. |
| 49 | Supply and fixingin repair Galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. |
| 50 | S&F in repair 15mm bore CP Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 51 | S&Fin repair 15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwedfor 15 mm iron pipe, complete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 52 | S&Fin repair 15mm boreStop valves, cast copper alloy,fancy type, chromium plated with long shankandcup (concealed type) screweddown, highpressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed, complete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 53 | S&F in repair 15mm bore CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 54 | S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flangescomplete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 55 | S&F in repair Chromium plated,towel ring, complete all as specified. Make:- Jainko,Essco,Parko, Prayag |
| 56 | S&F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.", complete all as specified. Make :- Jainko,Essco,Parko, Prayag |
| 57 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long . Complete all as specified. Make :- Jainko,Essco,Parko, Prayag |
| 58 | S&F in repair waste coupling of chromium plated brass32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . Make :- Jainko,Essco,Parko, Prayag |
| 59 | S&F in repair waste coupling of chromium plated brass40 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . Make :- Jainko,Essco,Parko, Prayag. |
| 60 | S&F in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.Make :- Jainko,Essco,Parko, Prayag |
| 61 | S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore. Make :- Jainko,Essco,Parko, Prayag |
| 62 | S&F in repairBrasschromiumplatedshower rosewith or without swivel joints, 125mm size, including fixing to steel pipe or unionMake :- Jainko,Essco,Parko, Prayag |
| 63 | S&F in repair Jet Spray (Stainless Steel) with 1.5 meter Tube complete all as specified. Make :- Jainko,Essco,Parko, Prayag |
| 64 | S&F in repairVitreous China, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass.complete all as specified and as directed by Engineer-in-charge.. Make :- Cera, Cat No- S2040119 or equivalent in Jaquar/ Hindware. |
| 65 | S&F in repair PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm "L" bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge. Make:- Cera, Cat No- B1010109 ( CONGO) or equivalent in Jaquar/ Hindware. |
| 66 | Supply and fixing in repairPVC Seat cover for EWC pan (White ) of standardd quality including hinges bolt etc all as directed by Engr-In-Carge.Make: CERA Cat No- B1510121 or equivalent in Jaquar/ Hindware. |
| 67 | Supply and fixing in repair Vitreous china ware pedestal type water closet white, with "P" or "S" trap including self closing seat cover, closed pattern with flat bottom,complete all as directed. Make:- Cera, Cat Part No- S1053101 or equivalent in Jaquar/ Hindware. |
| 68 | S&F in repair WC Orissa pattern white with integral foot rest580x 440 mm including L bend, &PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) Make:- Cera, Cat Part No-S3010102 (CALINA) or equivalent in Jaquar/ Hindware. |
| 69 | S&F in repair stainless steel lock grating plain/hole size 100 mmdiaincluding embeding in tiles with white cement. Make:- Jainko Cat No :-SGJ-4 or equivalent in Essco, Parko. |
| 70 | S&F in repair 15mm boreBib tap standard of PTMT fancy typeany colour high pressure screwed for iron pipe and fixed. ((Minimum weight 15mm-105gms) complete all as specified. Make:- Prayag or equivalent in Polytuf/ Jindal. |
| 71 | S&F in repair PTMT Shelf 450 mm long complete all as specified. Make:- Prayag. Cat No- 191 or equivalent in Polytuf/ Jindal. |
| 72 | S&F in repair PTMT Corner Shelf 200 mm long complete all as specified. Make:- Prayag. Cat No- 192 or equivalent in Polytuf/ Jindal. |
| 73 | S&F in repair PTMT Soap Dish/holder, Square, complete all as specified. Make:- Prayag. Cat No- 1951 or equivalent in Polytuf/ Jindal. |
| 74 | S&F in repair PTMT Towel rail, 450 mm long, complete all as specified. Make:- Prayag. Cat No- 199 or equivalent in Polytuf/ Jindal. |
| 75 | S&F in repair PTMT Overhead Shower rose Round size- 75 mm dia with 225 mm long shower arm with flange, complete all as specified. Make:- Prayag. Cat No- 1813C or equivalent in Polytuf/ Jindal. |
| 76 | S&F in repair PTMT Jet Spray ( with 1.00 mtr Tube), complete all as specified. Make:- Prayag, Cat No- 521 or equivalent in Polytuf/ Jindal. |
| 77 | Supply and fixingin repair PVC Waste pipe 32mm bore of required length complete .Make: Prayag Cat No 329 or equivalent in Polytuf/ Jindal. |
| 78 | Supply and fixing in repair PVC Waste pipe 40mm bore of required lengthcomplete for sink/WHB . Make: Prayag Cat No-330or equivalent in Polytuf/ Jindal. |
| 79 | Dismantling water tanks and removing to store of water storage tanks (Cap. 500 ltr to 1000 ltr ) complete all as specified and directed by Engineer-in-charge. |
| 80 | Dismantling water tanks and removing to store of water storage tanks (Cap. 250 ltr to 500 ltr ) complete all as specified and directed by Engineer-in-charge. |
| 81 | Supply and fixingRotational moulded polyethylene water storage tanks of1000 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified. Make : Vectus,Sintex, Sheetal. |
| 82 | Supply and fixingRotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specifiedMake : Vectus, Sintex, Sheetal. |
| 83 | Disconnecting of water tank of 500 ltr capacity setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing,etc. measured separately). |
| 84 | Cleaning and removing all scale and dirt etc, from exc 250 & n exc 500 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. |
| 85 | Cleaning and removing all scale and dirt etc, from exc 500 & n exc 1000 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. |
| 86 | Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed. |
| 87 | Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 15 mm bore pipe, including making connections complete all as specified and fixed. |
| 88 | Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms). |
| 89 | Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 25mm-455 gms). |
| 90 | S&F in repair PVC tank coversrequired for 500 ltr to 1000 ltr PVC water tanks complete all as specified and fixed |
| 91 | Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed |
| 92 | Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed |
| 93 | Taking up or down steel tubing of 25 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed |
| 94 | Supply and fixing tubes "medium grade" galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 95 | Supply and fixing tubes "medium grade" galvanised,20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 96 | Supply and fixing tubes "medium grade" galvanised,25 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 97 | Supply and fixing fittings for steel tubing galvanised, 15 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed |
| 98 | Supply and fixing fittings for steel tubing galvanised, 20 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed |
| 99 | Supply and fixing 20 mm nominal outer diaChlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all Plain CPVC SDR 11 fittings & brass threaded fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete as per direction of Engineer in Charge. Make:- Supreme, Prince, Prayag. |
| 100 | Supply and fixing 25 mm nominal outer diaChlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all Plain CPVC SDR 11 fittings & brass threaded fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete as per direction of Engineer in Charge. Make:- Supreme, Prince, Prayag. |
| 101 | M&L cutting chases, pinning in , making good to facings where required and pointing in cement mortar1:3 to ends or edges of landings,steps,cills,sunshades,shelves,lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good,cutting n.exc 10cm girth in brick walls. |
| 102 | Dismantling PVC/Cement/CI pipes 50 to 110 mm diaincluding allfittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed |
| 103 | Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by Engineer-in-charge. Make -Astral, Supreme, Finolex |
| 104 | Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ringjoints fixedto wallsincluding stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge. Make -Astral, Supreme, Finolex |
| 105 | Supply and fixing UPVC (SWR)type B pipes 75 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by Engineer-in-charge. Make -Astral, Supreme, Finolex |
| 106 | Supply and fixing UPVC(SWR)type B pipes 75 mm bore single socketed, in any length with rubber ringjoints fixedto wallsincluding stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge. Make -Astral, Supreme, Finolex |
| 107 | Supply and fixing, UPVC (SWR) , bends for75 mm bore , complete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 108 | Supply and fixing, UPVC (SWR) , bends with access doorfor75 mm bore , complete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 109 | Supply and fixing, UPVC(SWR) , bendsfor110 mm borecomplete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 110 | Supply and fixing, UPVC(SWR) , bends with access door, for110 mm borecomplete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 111 | Supply and fixing, UPVC branch piece, single (single "Y") with access door for 75 mm bore complete all as specified and directed.Make: Astral, Supreme, Finolex. |
| 112 | Supply and fixing, UPVC branch piece, single (single "Y") with access door for 110 mm bore complete all as specified and directed.Make: Astral, Supreme, Finolex. |
| 113 | Supply and fixing, UPVC(SWR), junction single,(single "T") with access door equal or unequal for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 114 | Supply and fixing, UPVC(SWR), junction single,(single "T") with access door equal or unequal for 110 mm bore , complete all as specified and as directed by Engineer-in-charge.Make -Astral,Supreme, Finolex |
| 115 | S&F UPVC (SWR) , reducers 110 mm dia complete all as specified. Make:- Astral, Supreme, Finolex. |
| 116 | S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.Make -Astral,Supreme, Finolex |
| 117 | Supply and fixing in repair UPVC (SWR) floor trap plain with gratinghaving dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.Make -Astral,Supreme, Finolex |
| 118 | S&F in repair,UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.Make -Astral,Supreme, Finolex |
| 119 | Rendering 15mm thck in CM 1:3 or Plain Cement Concrete as in sunken floorswithout extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately) |
| 120 | M&L applying a coat of bituminous primer conforming to IS-3384on prepared surface of roof/sunken slab after drying of primer apply APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced torched application and finally apply a coat of hot blown 85/25 graded bitumen conforming to IS-702 @ 1.2kg /sqm of plaster surface. |
| 121 | M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan ( Up to 4th floor) filling and mass concrete complete all as specified and directed by Emgr-in-charge. |
| 122 | M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified. |
| 123 | Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable materialfrom the work site ouside defence premises complete all as specified. |
| 124 | M&L Brick work with subclass "B" bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge |
| 125 | M&L Brick work with subclass "B" bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6but except bricks complete all as specified and as directed by Engineer-in-charge |
| 126 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified. |
| 127 | Material and labour for Providing, cement concrete 1:2:4type B-1 (using 20mm graded aggregate ), in lintels upto1.5m clear span,cills,steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering,slightly rounded or chamfered angles and throating, as directed |
| 128 | Demolition of cement concrete (unreinforced) ground floor to 4th floors and pavings n exc 15 cm thickness (below or above ground level ) and removingthe rubbish from the work site out side defence premises complete all as specified. |
| 129 | Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface(but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed. |
| 130 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushingsurface with neat cement slurry with 3.0 kg of cement per sq. metre, removing serviceable tiles to store and rubbish off the Cantt area complete all as directed |
| 131 | Material and labour glazed ceramic colouredDigital tiles in vertical surface300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved & Kept in GE"s sample room) |
| 132 | Material and labourNon - skid DigitalCeramicjoint lesscoloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including15 mm thick screed bed in CM 1:4. ( sample as approved & kept in GE"s sample room) |
| 133 | Description all as item No 132 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete. |
| 134 | Material and labourNon - skid DigitalCeramicjoint lesscoloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including15 mm thick screed bed in CM 1:4. ( sample as approved & kept in GE"s sample room) |
| 135 | Description all as item No 134 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete. |
| 136 | Material and labourVitrifiedCeramic(Double Charged) edge cutjoint freecoloured or printed any shade tiles10 mm thick (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to matchover and including15 mm thick screed bed in CM 1:4. (Sample as approved & Kept in GE"s sample room) |
| 137 | Description all as item No 136but as in vertical surfaces dado/skirting over a backing coat of CM 1:4, 10 mm thick complete. |
| 138 | Material and labour for Chequered cement concrete tiles 30cm x30cm x 25mm thick, with greay cement and pigment, set, jointed and pointed in neat cement slurry in floors and laid over and including 20mm thick screed bed in CM 1:4 etc complete all as specified and as directed |
| 139 | Material and labour for Precast factory made interlockingdesigener tiles glazed topmade in white cement and pigment base of thickness not less than 19 mm indifferent colour and pattern (compressive strength not less than 250 Kg/SqCm) setand jointed in neat cement slurry(colour and pattern as per sample kept in GE office as approved by GE)including 15 mm thick screed bedin CM 1:4 a complete all as specified and directed by Engr-in-Charge. |
| 140 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand |
| 141 | M&L 16 to 18mm thick Granite (of any type)work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge. |
| 142 | M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. |
| 143 | M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed. |
| 144 | M&L for Plain cement concrete(1:3:6), type C-2 (using 40 mm graded crushed stone aggregate) nominal mix, 75 mm thick, as in sub base offloors, finished even and faircomplete all as specified and as directed by Engineer-in-charge. |
| 145 | M&Lfor 25 mm thick cement concrete 1:2:4,type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and faircomplete all as specified and directed. |
| 146 | Supply and fixing in repair for bevelled edge mirror of size (600x450mm), selected quality glass approved size , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with SS screws and cup washers . |
| 147 | Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen orlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified anddirected by Engineer-in-charge. Make: Jainko, Model No- SSJ-1. & equivalent in Prayag,Nirali, Jayana. |
| 148 | S&F in repair sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified anddirected by Engineer-in-charge. Make:- Jainko Model No .-SSJ-8. & equivalent in Prayag, Nirali, Jayana. |
| 149 | S & F Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete.Make:- Jainko, Model No.KRJ-4. and equivalent in Prayag, Nirali, Jayana. |
| 150 | Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer), laid, bedded and pointed in any mortar, complete as specified and directed. |
| 151 | Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster any thickness and removal of debris off the premisesincluding grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust. |
| 152 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed. |
| 153 | M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of rooffinished fair & evenr and including mixing of water proofing compound (WPC shall be measured and paid separately) |
| 154 | M&Lforwater proofing treatment inthe following sequences:- (a) Applying1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely(b) Applying2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c)Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed . |
| 155 | M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc complete all as specified and as directed |
| 156 | M&L 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska |
| 157 | Ditto all as per item No 156 but except bricktiles. |
| 158 | Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-charge. |
| 159 | Supply only Water proofing compound liquid. |
| 160 | Cleaning of roof surfaces of RCC roof (any type) tiles with brush and removing all vegetation, plants, roots, grass, leaves any type ofmaterial asked to remove at any height of bldg or any part of bldg complete all as directed. |
| 161 | Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.Note :- Work will be carried out upto 4th storey of bldgs also as per direction of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. |
| 162 | Rendering 10mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:6 , rendering is to be finished even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-charge. |
| 163 | Rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 4th storey with necessary scaffolding) complete all as specified and as directed by Engineer-in-charge. |
| 164 | Rendering 10 mm thick on fair faces of brick or concrete surfaceceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-charge. |
| 165 | M&L for repairing of concrete surfaces such asbalcony, chajjas, upward or downward facias ,column, pillar, ceiling and similar items with plain cement concrete 1:2:4type B-0 or rendering 10-15mm thickas per site requirement in CM 1:3 without using extra cement finished even and fair complete all as specified and directed (Up to fourth storey bldgs and including necessory formwork and scaffolding required as per site condition also taking down or dismantling as required at site. |
| 166 | M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cmincluding preparation and rubbing with sand paper to make surface even and smooth complete all as specified. |
| 167 | M&L for applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth and apply putty and primer where requred complete all as specified. |
| 168 | M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth. |
| 169 | M&L for applying one coat of synthetic enamel paint on old painted wood surfaces of any description having width/girth exceeding 10 cm complete all as specified including preparation and where requered to make surface even and smooth. |
| 170 | M&L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying two coat of oil bound distemper on old decorated wall surface including two coats of wall care putty of 1 to 2 mm thick on uneven surface as and where required. |
| 171 | Material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified. |
| 172 | M&L for preparation of old decorative plastered/concreat surface of wall, chajja, facia, face of columns, beam ect by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applyingone coat of weather proof exterior emulsion (APEX) with necessary scaffoding up to 4th storey,including necessary filling of wall care putty on uneven surface as and where required all as specified. |
| 173 | M&L for preparation of newplastered/concrete surfaces of walls, (up to 4th sorey with necessary scaffolding) andapplying two coat of cement based paint over one coat of primer complete all as per specified and directed by Engr-in-charge. |
| 174 | M&L for preparation of old decorated plastered /concrete/ brick surfaces of walls (up to 4th storey with necessary scaffolding) andapplying one coat of cement based paint on old decorated surfaces including preparation. |
| 175 | M&L for preparation of old decorated brick /concrete plastered /un-plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed. |
| 176 | M&L for preparation of new decorated brick /concrete plastered /un-plastered surfaces of Ceiling and applying one coat of white wash on ceiling. |
| 177 | Demolition ofreinforced cement concrete of any discription and any position( ground to 4th floors) and removingthe rubbish from the work site out side defence premises complete all as specified. |
| 178 | M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specifiedand directed. |
| 179 | M&Lfor TMTmildsteel bars10mm dia and over, cutto length, bentto shape required, including cranking, bendingspirallyforhooping for column, hookingendandbinding withandincludingmildsteelwire(annealed) not lessthan0.9 mm dia or securing with clips, complete all as specified and directed. |
| 180 | M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed. |
| 181 | M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar workexc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed |
| 182 | Repair to Panelled door shutter,flush door shutter & wire gauze door shutter any type and change the following items as well as requred:- (a)MS Butt hinge size 100mm medium weight |
| 183 | (b)Aluminium anodised barrel tower bolt of extruded section size150 mm |
| 184 | (c)Aluminium anodised barrel tower bolt of extruded section size200 mm |
| 185 | (d) Aluminium handle fabricated type,anodised size 100mm |
| 186 | (e) Aluminium handle fabricated type,anodised size 150mm |
| 187 | (f) Aluminiumalloy, anodised, sliding door bolt with hasp, staple (bolt type)size 250 mm |
| 188 | (g) Galvanised MS wire cloth, 0.56 nominal dia and average width of aperture 1.18. incl wooden beading |
| 189 | (h) Mild steel 300 mm, ordinary rat tail rod pattern springs, incl roller and roller plate |
| 190 | Repair to existing PVC pipe/CI pipe including making the joints water tight by using suitable material including cleaning if requiredand refixingof any dia. Note :Work to be carried out up to 4th storey bldg in any condition of working place/area |
| 191 | Material and labour for Sealing of WC/Floor traps joint and joints between rain water pipe and roofby using neat white cement paste or leak proof material and making the joint leakproof in case seepage is observed from WC/Floor trap and joint of rain water pipe and roof slab.Note :Work to be carried out up to 4th storey bldg in any condition of working place/area |
| 192 | Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed. |
| 193 | M&L for complete point wiringwith 1.5 Sqmm single core multi stranded copper conductor FRLSH-PVC insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH-PVC insulated drawn in and including concealed PVC rigid conduit medium gradeISI marked terminated into GI modular sunken boxes including white cover plate with frame as per relevant ISfor mounting moudlar switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One light/ fan point/exhaust fan point controlled by one way switch 6 Amps. |
| 194 | (b) One 3 pin Socket outlet 6A point on same board. |
| 195 | Ditto all as per Srl item No 193 above but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire. |
| 196 | S & F moudlar switch piano flush button single pole one way, 6 Amp,1 moudle. Complete all as specified and directed. 240 V |
| 197 | Supply and fix moudlarSocket outlet 2-in-15 pin, 6 Amps made of polycarbonate flush type complete all as specified and as directed. |
| 198 | Supply and fix moudlar Socket outlet 2-in-15 pin, 6 & 16 Amps flush type made of polycarbonate complete all as specified and as directed. |
| 199 | Supply and fix moudlarSwitch piano made of polycarbonateflush button single pole one way, 16 Amps, 230/240 V complete all as specified and as directed by Engineer-In-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
