Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M079-Polythene water storage tank of ISI mark (e.g sintex/sinter/himgiri/gangotietc)with cover and locking system |
| 2 | M129HDPE pipes 75mm dia |
| 3 | M130HDPE pipes 90mm dia |
| 4 | M193GI Pipe 50 mm dia (TATA or equivalent make) |
| 5 | M337Jute |
| 6 | M922G.M. Ferrules |
| 7 | (i) 8 mm dia Wt. not less than 400 gms |
| 8 | (ii) 10 mm dia Wt. not less than 400 gms |
| 9 | (iii) 15 mm dia Wt. not less than 400 gms |
| 10 | (iv) 20 mm dia Wt. not less than 600 gms |
| 11 | (v) 25 mm dia Wt. not less than 900 gms |
| 12 | M923Stop Cocks |
| 13 | (i) 15 mm brass stop cock wt. not less than 300 gms |
| 14 | (ii) 20 mm brass stop cock wt. not less than 400 gms |
| 15 | (iii) 25 mm brass stop cock wt. not less than 575 gms |
| 16 | (iv) 32 mm brass stop cock wt. not less than 850 gms |
| 17 | (v) 40 mm brass stop cock wt. not less than 1.15 kg |
| 18 | (vi) 50 mm brass stop cock wt. not less than 2.15 kg |
| 19 | (vii) 15 mm dia C.I. Body brass working part stop cock. |
| 20 | (viii) 20 mm dia C.I. Body brass working part stop cock. |
| 21 | (ix) 25 mm dia C.I. Body brass working part stop cock. |
| 22 | M924G.M. Full way Valve |
| 23 | (i) 15 mm dia wt. not less than 300 gms without wheel |
| 24 | (ii) 20 mm dia wt. not less than 400 gms without wheel |
| 25 | (iii) 25 mm dia wt. not less than 500 gms without wheel |
| 26 | (iv) 32 mm dia wt. not less than 700 gms without wheel |
| 27 | (v) 40 mm dia wt. not less than 1.0 kg without wheel |
| 28 | (vi) 50 mm dia wt. not less than 1.4 kg without wheel |
| 29 | (vii) 65 mm dia wt. not less than 1.8 kg without wheel |
| 30 | (viii) 80 mm dia wt. not less than 2.5 kg without wheel |
| 31 | M925G.M. NON RETURN VALVE VERTICAL |
| 32 | (i) 15 mm dia wt. not less than 150 gms |
| 33 | (ii) 20 mm dia wt. not less than 250 gms |
| 34 | (iii) 25 mm dia wt. not less than 375 gms |
| 35 | (iv) 32 mm dia wt. not less than 600 gms |
| 36 | (v) 40 mm dia wt. not less than 700 gms |
| 37 | (vi) 50 mm dia wt. not less than 1.0 kg |
| 38 | (vii) 65 mm dia wt. not less than 1.20 kg |
| 39 | (viii) 80 mm dia wt. not less than 1.50 kg |
| 40 | (ix) 100 mm dia wt. not less than 1.80 kg |
| 41 | M926G.M. Non Return Valve Horizontal |
| 42 | (i) 15 mm dia wt. not less than 150 gms |
| 43 | (ii) 20 mm dia wt. not less than 250 gms |
| 44 | (iii) 25 mm dia wt. not less than 375 gms |
| 45 | (iv) 32 mm dia wt. not less than 600 gms |
| 46 | (v) 40 mm dia wt. not less than 700 gms |
| 47 | (vi) 50 mm dia wt. not less than 1.0 kg |
| 48 | (vii) 65 mm dia wt. not less than 1.20 kg |
| 49 | (viii) 80 mm dia wt. not less than 1.50 kg |
| 50 | (ix) 100 mm dia wt. not less than 1.80 kg |
| 51 | M927 COCKs |
| 52 | (i) 15 mm dia G.M. bib cock wt. not less than 300 gms |
| 53 | (ii) 15 mm dia brass bib cock wt. not less than 400 gms |
| 54 | (iii) 15 mm dia C.I. bib cock wt. not less than 400 gms |
| 55 | (iv) 15 mm dia C.I. Body brass working part spray painted bib cock wt. not less than 400 gms |
| 56 | (v) 15 mm dia C.I. Brass pillar cock cock wt. not less than 400 gms |
| 57 | (vi) 15 mm C.I. Plug cock ordinary |
| 58 | (vii) 15 mm C.I. push cock ordinary |
| 59 | M928CHROMIUM PLATED BRASS FITTINGS |
| 60 | (i) C.P. Shower rose 100 mm dia |
| 61 | (ii) C.P. Shower rose 125 mm dia |
| 62 | (iii) P.V.C. Shower rose 150 mm dia |
| 63 | (iv) P.V.C Shower rose 125 mm dia |
| 64 | M929CONNECTION PIPE |
| 65 | (i) 15 mm dia x 30 cm. long lead connection pipe with brass fittings. |
| 66 | (ii) 15 mm dia x 45 cm. long lead connection pipe with brass fittings. |
| 67 | (iii) 15 mm dia x 30 cm. long PVC connection pipe with brass fittings. |
| 68 | (iv) 15 mm dia x 45 cm. long PVC connection pipe withbrass fittings. |
| 69 | M930G.I. FITTINGS (CONFORMING TO I.S. - 1879 ) ISI Marked |
| 70 | [A] G.I. BEND |
| 71 | (i) 15 mm |
| 72 | (ii) 20 mm |
| 73 | (iii) 25 mm |
| 74 | (iv) 32 mm |
| 75 | (v) 40 mm |
| 76 | (vi) 50 mm |
| 77 | (vii) 65 mm |
| 78 | (viii) 80 mm |
| 79 | (ix) 100 mm |
| 80 | (x) 125 mm |
| 81 | (xi) 150 mm |
| 82 | [B] ELBOW OF THE FOLLOWING SIZES |
| 83 | (i) 15 mm |
| 84 | (ii) 20 mm |
| 85 | (iii) 25 mm |
| 86 | (iv) 32 mm |
| 87 | (v) 40 mm |
| 88 | (vi) 50 mm |
| 89 | (vii) 65 mm |
| 90 | (viii) 80 mm |
| 91 | (ix) 100 mm |
| 92 | (x) 125 mm |
| 93 | (xi) 150 mm |
| 94 | [C] TEE PLAIN OF THE FOLLOWING SIZES |
| 95 | (i) 15 mm |
| 96 | (ii) 20 mm |
| 97 | (iii) 25 mm |
| 98 | (iv) 32 mm |
| 99 | (v) 40 mm |
| 100 | (vi) 50 mm |
| 101 | (vii) 65 mm |
| 102 | (viii) 80 mm |
| 103 | (ix) 100 mm |
| 104 | (x) 125 mm |
| 105 | (xi) 150 mm |
| 106 | [D] REDUCING TEE PLAIN OF THE FOLLOWING SIZES(Taking larger dimension) |
| 107 | (i) 20 mm |
| 108 | (ii) 25 mm |
| 109 | (iii) 32 mm |
| 110 | (iv) 40 mm |
| 111 | (v) 50 mm |
| 112 | (vi) 65 mm |
| 113 | (vii) 80 mm |
| 114 | (viii) 100 mm |
| 115 | (ix) 125 mm |
| 116 | (x) 150 mm |
| 117 | [E] SOCKET PLAIN OF THE FOLLOWING SIZE (Taking larger dimension) |
| 118 | (i) 15 mm |
| 119 | (ii) 20 mm |
| 120 | (iii) 25 mm |
| 121 | (iv) 32 mm |
| 122 | (v) 40 mm |
| 123 | (vi) 50 mm |
| 124 | (vii) 65 mm |
| 125 | (viii) 80 mm |
| 126 | (ix) 100 mm |
| 127 | (x) 125 mm |
| 128 | (xi) 150 mm |
| 129 | [F] REDUCING SOCKET PLAIN OF THE FOLLOWING SIZES (Taking larger dimension) |
| 130 | (i) 20 mm |
| 131 | (ii) 25 mm |
| 132 | (iii) 32 mm |
| 133 | (iv) 40 mm |
| 134 | (v) 50 mm |
| 135 | (vi) 65 mm |
| 136 | (vii) 80 mm |
| 137 | (viii) 100 mm |
| 138 | (ix) 125 mm |
| 139 | (x) 150 mm |
| 140 | [G] UNION SOCKET OF THE FOLLOWING SIZES |
| 141 | (i) 15 mm |
| 142 | (ii) 20 mm |
| 143 | (iii) 25 mm |
| 144 | (iv) 32 mm |
| 145 | (v) 40 mm |
| 146 | (vi) 50 mm |
| 147 | (vii) 65 mm |
| 148 | (viii) 80 mm |
| 149 | (ix) 100 mm |
| 150 | (x) 125 mm |
| 151 | (xi) 150 mm |
| 152 | [H] PLUGS OF THE FOLLOWING SIZES |
| 153 | (i) 15 mm |
| 154 | (ii) 20 mm |
| 155 | (iii) 25 mm |
| 156 | (iv) 32 mm |
| 157 | (v) 40 mm |
| 158 | (vi) 50 mm |
| 159 | (vii) 65 mm |
| 160 | (viii) 80 mm |
| 161 | (ix) 100 mm |
| 162 | (x) 125 mm |
| 163 | (xi) 150 mm |
| 164 | [I] JAM NUTS OF THE FOLLOWING SIZES |
| 165 | (i) 15 mm |
| 166 | (ii) 20 mm |
| 167 | (iii) 25 mm |
| 168 | (iv) 32 mm |
| 169 | (v) 40 mm |
| 170 | (vi) 50 mm |
| 171 | (vii) 65 mm |
| 172 | (viii) 80 mm |
| 173 | (ix) 100 mm |
| 174 | (x) 125 mm |
| 175 | (xi) 150 mm |
| 176 | [J] G.I. NIPPLE OF THE FOLLOWING SIZES |
| 177 | (i) 15 mm dia x 100 mm long |
| 178 | (ii) 20 mm dia x 100 mm long |
| 179 | (iii) 25 mm dia x 100 mm long |
| 180 | (iv) 32mm dia x 100 mm long |
| 181 | (v) 40 mm dia x 100 mm long |
| 182 | (vi) 50 mm dia x 100 mm long |
| 183 | (vii) 65 mm dia x 100 mm long |
| 184 | (viii) 80 mm dia x 100 mm long |
| 185 | (ix) 100 mm dia x 100 mm long |
| 186 | [K] G.I. PIPES MIDIUM(Tata mark) OR EQUIVALENT as per IS-1239 (part-01)/2004 ISI Marked/Medium Quality |
| 187 | (i) 15 mm dia |
| 188 | (ii) 20 mm dia |
| 189 | (iii) 25 mm dia |
| 190 | (iv) 32 mm dia |
| 191 | (v) 40 mm dia |
| 192 | (vii) 65 mm dia |
| 193 | M931MIRRORS |
| 194 | (a) Mirror of 6 mm thick plain glass 600 mm x 450 mm beveled edge mirror includingC.P. brass revolving fittings 3 mm plywood boardand C.P. hinges etc.to fix the mirror |
| 195 | (b) -do- 450 mm x 300 mm -do- |
| 196 | M932(a) Glass shelf 600 mm x 125 mm with C.P. brass rail |
| 197 | (b) -do- 450 mm x 125 mm -do- |
| 198 | M933(a) C.P. Brass towel rail 20 mm x 600 mm with bracket all complete |
| 199 | (b) Anodized aluminum 20 mm x 600 mm towel rail complete with brackets |
| 200 | M934C.P. brass soap dish medium quality with screw andhinges etc. |
| 201 | M935C.P. liquid soap solution holder |
| 202 | M936VITREOUS WHITE GLAZED INDIAN WATER CLOSET OF Hindustan / Parry Ware / Cera / Naycer or anyotherequivalent make |
| 203 | (a) 580 mm long |
| 204 | (b) 510 mm long |
| 205 | (c) 450 mm long |
| 206 | (d) 510 mm long White glazed fiber I.W.C |
| 207 | M937PAIR OF VETREOUS WHITE GLAZED FOOT REST OF Hindustan / Parryware / Cera / Naycer or any other equivalent make |
| 208 | M93815 liters capacity pull and let go high level C.I. cistern complete with ball cock and a pair of bracket |
| 209 | M939(a) 12.5 liters lowdown C.I. Cistern |
| 210 | (b) 10.0 liters capacity P.V.C. low design cistern |
| 211 | M940(a) White Glazed vitreous E.W.C with \"P\" trap orany other equivalent make |
| 212 | (b) E.W.C with \"S\" trap 400 mm high of Hindustan / Parry ware / Cera / Naycear or any other equivalent make |
| 213 | (c) Black / white plastic seat for E.W.C -do- as above. |
| 214 | M941(a) White glazed vitreous earthen were urinal flat back of Hindustan / Parryware / Cera / Naycer or any other equivalent make 600 mm x 350 mm size |
| 215 | (b) -do- squatting small 450 mm x 350 mm |
| 216 | (c) -do- squatting large 600 mm x 350 mm |
| 217 | (d) White glazed vitreous earthen ware urinal standing corner size 600 mm x 350 mm Hindustan / Parryware /Cera / Naycer or any other equivalent make |
| 218 | (e) Partition plate for urinal 25\" x 13\" size |
| 219 | (f) 5 liters C.I. automatic cistern with all P.V.C fittings |
| 220 | M942White glazed vitreous Wash Hand Basin 550 mm x 400mm size of Hindustan / Parryware / Cera / Naycer or any otherequivalent make |
| 221 | M943White glazed vitreous earthen ware kitchensinks of Hindustan / Parryware / Cera / Nayceror any other equivalent make |
| 222 | (a) Kitchen sink 600 mm x 450 mm x 200 mm (24\" x 18\" x 8\") |
| 223 | (b) Kitchen sink 600 mm x 450 mm x 250 mm (24\" x 18\" x 10\") |
| 224 | (c) Lab sink 450 mm x 300 mm x 150 mm (18\" x 12\" x 6\") |
| 225 | (d) Lab sink 300 mm x 250 mm x 150 mm (12\" x 10\" x 6\") |
| 226 | M944DRAIN BOARD |
| 227 | (a) 600 mm x 450 mm (24\" x 18\") |
| 228 | (b) 525 mm x 450 mm (21\" x 18\") |
| 229 | M945H.C.I. Pipes |
| 230 | (a) 50 mm dia single socket 6\"-0\" (with ear weight 13 kg) |
| 231 | (b) 80 mm dia single socket 6\"-0\" (with ear weight 18 kg) |
| 232 | (c) 100 mm dia single socket 6\"-0\" (with ear weight 23 kg) |
| 233 | (d) 150 mm dia single socket 6\"-0\" (with ear weight 30 kg) |
| 234 | (e) 50 mm dia double socket 6\"-0\" (with ear weight 14 kg) |
| 235 | (f) 80 mm dia double socket 6\"-0\" (with ear weight 19 kg) |
| 236 | (g) 100 mm dia double socket 6\"-0\" (with ear weight 25 kg) |
| 237 | (h) 150 mm dia double socket 6\"-0\" (with ear weight 13 kg) |
| 238 | (i) 50 mm dia single socket 3\"-0\" (with ear weight 7.25 kg) |
| 239 | (j) 80 mm dia single socket 3\"-0\" (with ear weight 10.5 kg) |
| 240 | (k) 100 mm dia single socket 3\"-0\" (with ear weight 13.75 kg) |
| 241 | (l) 150 mm dia single socket 3\"-0\" with ear |
| 242 | (m) 50 mm dia single socket 2\"-0\" (with ear weight 5.35 kg) |
| 243 | (n) 80 mm dia single socket2\"-0\" (with ear weight 8.00 kg) |
| 244 | (o)100 mm dia single socket 2\"-0\"(with ear weight 10.10 kg) |
| 245 | (p) 150 mm dia single socket 2\"-0\" with ear |
| 246 | (q) 50 mm dia single socket 1\"-0\" (with ear weight 3.4 kg) |
| 247 | (r) 80 mm dia single socket 1\"-0\"(with ear weight 5.50 kg) |
| 248 | (s) 100 mm dia single socket 1\"-0\"(with ear weight 7.60 kg) |
| 249 | (t) 150 mm dia single socket |
| 250 | M946H.C.I. FITTINGS. |
| 251 | (I) Plain bend of following size |
| 252 | (a) 50 mm dia (weight without ear and socket 2.75 kg) |
| 253 | (b) 80 mm dia (weight without ear and socket 3.5 kg) |
| 254 | (c) 100 mm dia (weight without ear and socket 4.5 kg) |
| 255 | (d) 150 mm dia (weight without ear and socket 4.5 kg) |
| 256 | (II) Bend with door with following size |
| 257 | (a) 50 mm dia (Wight without ear and socket 2.75 kg) |
| 258 | (b) 80 mm dia (Wight without ear and socket 4.00 kg) |
| 259 | (c) 100 mm dia -do- 5.5 kg |
| 260 | (d) 150 mm dia -do- |
| 261 | (III) Single Junction with door of followings sizes. |
| 262 | (a) 50 mm dia (weight without ear and socket 3.75 kg) |
| 263 | (b) 80 mm dia (weight without ear and socket 6.50 kg) |
| 264 | (c) 100 mm dia -do- 9.50 kg |
| 265 | (d) 150 mm dia -do- |
| 266 | (IV) Double junction with door of following sizes. |
| 267 | (a) 50 mm dia -do- 4.5 kg |
| 268 | (b) 80 mm dia -do- 7.00 kg |
| 269 | (c) 100 mm dia -do- 13.00 kg |
| 270 | (d) 150 mm dia -do- |
| 271 | (V) Heel rest bend of following sizes |
| 272 | (a) 50 mm dia |
| 273 | (b) 80 mm dia |
| 274 | (c) 100 mm dia |
| 275 | (d) 150 mm dia |
| 276 | (VI) Cowel of following sizes |
| 277 | (a) 50 mm dia (weight without ear and socket 2.25 kg) |
| 278 | (b) 80 mm dia (weight without ear and socket 3.25 kg) |
| 279 | (c) 100 mm dia (weight without ear and socket 3.25 kg) |
| 280 | (d) 150 mm dia -do- |
| 281 | (VII) 100 mm dia \"P\" trap (wt without ear and socket)8.5 kg |
| 282 | (VIII) 100 mm dia \"P\" trap (wt without ear and socket)8.8 kg |
| 283 | (IX) 100 mm x 80 mm floor trap (weight without ear and socket) 4.00 kg |
| 284 | (X) Pass over 50 mm x 150 mm for 50 mm projection |
| 285 | (XI) -Do- 100 mm x 150 mm for 100 mm projection |
| 286 | (XII) Inverted Junction single 100 mm x 50 (weight without ear and socket) 9.0 kg |
| 287 | (XIII) Inverted Junction double 100 mm x 50 mm x 50 mm(weight without ear and socket) 12.0 kg |
| 288 | (XIV) H.C.I. offset 80 mm projection of the following Size |
| 289 | (a) 50 mm dia (weight without ear and socket) 2.75 kg |
| 290 | (b) 80 mm dia -do- 3.50 kg |
| 291 | (c) 100 mm dia -do- 5.00 kg |
| 292 | (d) 150 mm dia -do- |
| 293 | (XV) H.C.I. Socket of following sizes |
| 294 | (a) 50 mm dia (weight without ear) 1.50 kg |
| 295 | (b) 80 mm dia (weight without ear) 3.00 kg |
| 296 | (c) 100 mm dia (weight without ear) 4.50 kg |
| 297 | (d) 150 mm dia (weight without ear) -do- |
| 298 | M947C.I. Cover with frame for manhole and inspection chamber |
| 299 | (a) 600 mm x 450 mm size (wt. 39 kg) |
| 300 | (b) 600 mm x 450 mm size (wt. 25 kg) |
| 301 | (c) 500 mm x 450 mm size (wt. 25 kg) |
| 302 | M948C.I. Bracket pair for W.H.B |
| 303 | (a) 550 mm x 400 mm size (22\" x 16\") |
| 304 | (b) -do- for 12.5 liter cistern |
| 305 | (c) -do- for 600 mm x 450 mm (24\" x 18\") sink |
| 306 | (d) 40 mm x 60 mm MS Plate bracket for sink as above |
| 307 | M949(a) 32 mm (1 1/4\") C.P. Brass waste for W.H.B |
| 308 | (b) 40 mm (1 1/2\") C.P. Brass waste for W.H.B for sink |
| 309 | (c) 32 mm (1 1/4\") C.P. waste of white metal |
| 310 | (d) 40 mm (1 1/2\") C.P. waste of white metal |
| 311 | M950(a) 32 mm (1 1/4\") P.V.C. waste pipe 750 mm long (2\"6\" long) withbrass Union for W H B |
| 312 | (b) 40 mm (1 1/2\") P.V.C. waste pipe 750 mm long(2\"6\" long)with brass Union for W H B |
| 313 | M95132 mm (1 1/4\") P.V.C. telescopic flush pipe with brass union for high level cistern |
| 314 | M952Rubber Inserttion 3 mm (1/8\") thick |
| 315 | M953Pig Lead |
| 316 | M954Yarn |
| 317 | M955Rubber Gasket for D.I pipe of Good quality |
| 318 | (a) 80 mm |
| 319 | (b)100 mm |
| 320 | (c)125 mm |
| 321 | (d)150 mm |
| 322 | (e)200 mm |
| 323 | (f)250 mm |
| 324 | (g)300 mm |
| 325 | (h)350 mm |
| 326 | (i)400 mm |
| 327 | (j)450 mm |
| 328 | (k)500 mm |
| 329 | (l)600 mm |
| 330 | (m)700 mm |
| 331 | (n)750 mm |
| 332 | (o)800 mm |
| 333 | (p)900 mm |
| 334 | (q)1000 mm |
| 335 | (r)1200 mm |
| 336 | M956Cotton waste |
| 337 | M957Asbestos Suta (gland packing) |
| 338 | M958Solvent Cement |
| 339 | M959Hydrocloric acid (Sepecific gravity 1.20) |
| 340 | M960CP & PVC Fitting |
| 341 | (i)32 mm dia C.P. Waste |
| 342 | (ii)32 mm dia PV C waste pipe 750 mm long with coupling |
| 343 | (iii)40 mm dia C.P. waste |
| 344 | (iv 40 mm dia PVC waste pipe 750 mm long with coupling |
| 345 | (v 100 mm dia steel jali |
| 346 | (vi)15 mm dia C.P. nipple with coupling (short pieces) |
| 347 | (vii)50 mm dia PVC pipe with coupling |
| 348 | M961Special type of C.P. Bath room fittings for V.I.P.buildings(JAL, Jaquar, Marc or equivalent mark) |
| 349 | (i) Pillar Cock (ISI) |
| 350 | (ii) Pillar Cock (Long neck) |
| 351 | (iii) Bib Cock (ISI) |
| 352 | (iv) Bib Cock (Long Thread) |
| 353 | (v) Angular Stop Cock |
| 354 | (vi) Angular Stop Cock (Long Thread) |
| 355 | (vii) Concealed stop cock reduce (ISI) |
| 356 | (viii) Concealed stop Cock heavy-duty extra adjustable wall flange |
| 357 | (ix) Long Body Bib Cock |
| 358 | (x) Swan Neck Tap with left hand Operating Knob |
| 359 | (xi) Central hole basin mixer (Best Quality) |
| 360 | (xii) Wall mixer with telephonic shower arrangement |
| 361 | (xiii) Wall mixer with provision for over head shower with elbow coupling and well flange |
| 362 | (xiv) Wall mixer 3 in 1 system with provision for over head shower with elbow coupling and wall flange |
| 363 | (xv) Sink mixer with swinging casted spout |
| 364 | (xvi) Sink Cock with swinging casted spout |
| 365 | (xvii) 4 - way diverter for concealed fittings |
| 366 | (xviii) Pressure adjustable shower with revolving joint |
| 367 | (xix) Telephone shower with flexible pipe |
| 368 | (xx) Flush Cock with wall flange (25 mm) |
| 369 | (xxi) Towel Rail 24\" |
| 370 | (xxii) Towel Ring |
| 371 | (xxiii) Soap dish |
| 372 | (xxiv) Tumbler Holder |
| 373 | (xxv) Toilet Paper Holder |
| 374 | (xxvi) Glass Shelf 22\" |
| 375 | (xxvii) Corner glass shelf with bracket |
| 376 | (xxviii) Flush Valve complete with 32 mm size controlcock & flange |
| 377 | M962C.I Special & PVC Pipes |
| 378 | 1. C.I double shocketted fittings bend such as bend, tee, taper, |
| 379 | (a) 80-200 mm |
| 380 | (b) 250-700 mm |
| 381 | (c) 700-1000 mm |
| 382 | 2. C.I double flange fittings such as tee, taper, tailpiece,bend etc |
| 383 | (a) 80-200 mm |
| 384 | (b) 250-700 mm |
| 385 | (c) 700-1000 mm |
| 386 | Spare parts of Hand Pump |
| 387 | M963Hexagonal Bolt M12x1.75x40mm long common to Marks II & III |
| 388 | M964Hexagonal Nut M12x1.75mm |
| 389 | M965Washer M12 (2.5mm thick) |
| 390 | M966High tensile bolt M10x1.5x40mm long. |
| 391 | M967Nyloc Nut M10x1.5mm |
| 392 | M968Handle Axle (Stainless Steel) |
| 393 | M969Washer for Handle Axle (4mm thick) |
| 394 | M970Ball Bearing 6204 Z |
| 395 | M971Spacer for Handle. |
| 396 | M972Chain with coupling. |
| 397 | M973Hexagonal Bolt for front Cover M12x1.75mm long. |
| 398 | M974Nitrile Rubber cup washer for Mark – II & III |
| 399 | M975Nitrile Sealing ring Mark – II |
| 400 | M976Nitrile Rubber Seating Big for Lower valve Mark-II |
| 401 | M977Nitrile Rubber Seating Small for Upper valve Mark-II. |
| 402 | M978Hexagonal rod coupling M12x1.75x50mm long. |
| 403 | M979Pump Head Assembly (G.I.) with front cover, Bolt & third plate. |
| 404 | M980Front cover (G.I.) |
| 405 | M981Handle Assembly (G.I.) |
| 406 | M982(a) Water Tank Assemblyfor Mark – II (G.I.) |
| 407 | (b) Water Tank Assembly for Mark – III (VLOM-65) |
| 408 | M983Stand Assembly (G.I.) Normal. |
| 409 | M984Stand Assembly (Telescopic) (G.I). |
| 410 | M985Connecting Rod 3mtr. Long with coupling and nut (Electrogalvanized) |
| 411 | M986a) Cylinder Assembly complete set for Mark-II |
| 412 | b) Cylinder Assembly complete set for Mark-III (VLOM-65) |
| 413 | M987a) Upper valve Assembly complete set for India Mark-II |
| 414 | b) Upper valve Assembly complete set for India Mark-III (VLOM-65) |
| 415 | M988a) Lower valve Assembly complete set for India Mark-II |
| 416 | b) Lower valve Assembly complete set for IM-III |
| 417 | M989Reducer Cap for Cylinder Mark-II |
| 418 | M990a) Plunger Rod (S.S.) for Mark – II |
| 419 | b) Plunger Rod (S.S.) for Mark – III |
| 420 | M991Upper valve Guide (G.M.). |
| 421 | M992Rubber Seat Retainer for Mark-II |
| 422 | M993Third Plate for Head Assembly (Galanized) |
| 423 | M994Cylinder Body with brass liner for IM-II with reducer cap for Top and Bottom. |
| 424 | M995Gun Metal Spacer. |
| 425 | M996Check valve Guide Mark-II |
| 426 | M997a) Check Valve Seat for Mark – II |
| 427 | b) Check Valve Seat for Mark – III |
| 428 | M998Nitrile Rubber “O” ring (VLOM-65) |
| 429 | M999Push Rod for Mark – III (S.S). |
| 430 | M1000Check Nut for Push Rod (S.S.). |
| 431 | M1001Nitrile Rubber Cup Washer for VLOM-50 |
| 432 | M1002Nitrile Rubber Sealing Ring for Mark – III VLOM-65 |
| 433 | M1003Nitrile Rubber Seating Big for Lower Valve MK-II |
| 434 | M1004Nitrile Rubber Seating Big for Lower Valve M-III VLOM-65) |
| 435 | M1005Nitrile Rubber Bobbin VLOM-50 |
| 436 | M1006Nitrile Rubber “O” Ring VLOM-50 |
| 437 | M1007Nitrile Rubber cone for VLOM-50 |
| 438 | M1008Nitrile Rubber cone for VLOM-65 |
| 439 | M1009Nitrile Rubber Centralizer 150mm for (VLOM-65). |
| 440 | M1010Nitrile Rubber Centralizer 125mm for (VLOM-65). |
| 441 | M1011Nitrile Rubber Centralizer 150mm for (VLOM-50). |
| 442 | M1012Nitrile Rubber Centralizer 125mm for VLOM-50 |
| 443 | M1013Nitrile Rubber Centralizer 100mm for VLOM-50 |
| 444 | M1014Water Tank Assembly Mark – III VLOM-50 |
| 445 | M1015Cylinder Assembly Complete set for Mark – III (VLOM-50) |
| 446 | M1016Upper valve Assembly complete set for IM-III (VLOM-50) |
| 447 | M1017Lower valve Assembly complete set for IM-III (VLOM-50) |
| 448 | M1018a) Upper Cap Cylinder Mark – III (VLOM-65) |
| 449 | b) Upper Cap Cylinder Mark – III (VLOM-50) |
| 450 | M1019a) Bottom Cap for Mark – III (VLOM-50) |
| 451 | b) Bottom Capfor Mark – III (VLOM-65) |
| 452 | M1020Follower for IM-III |
| 453 | M1021Cage for Mark-III |
| 454 | M1022S.S. Hexagonal Bolt M-6x25mm long. |
| 455 | M1023Basic rate of standard I.S.I. mark Deep Well Hand Pump for India mark-2, I.S.I. 15500 (Part 2) / 2004 with latest revision including 12mm x 3meter long 8 no. Connecting Rods made of bright bar electro-galvanized fitted with coupler & normal stand assembly ecommended for use with cylinder assembly suitable for bore well dia 100 to 125mm casing pipe. |
| 456 | M1024Basic rate of UPVC pipe 125mm dia conforming to I.S.I. latest revision is 12818/2016 CML No. 5543459 |
| 457 | M1025Basic rate of 32mm G.I. pipe in 3 mtrs. Length (medium) with seamless socket as per relevent B.I.S. specificationIS 1239(PART-I)/2004 |
| 458 | M1026DI Pipe : Providing and Supplying ISI mark Centrifugally cat (Spun) Ductile Iron Pipes of 100 mm and above all diameter for water works with socket & spigot ends confirming to IS 8329/2000 in the standard working lengths of 4.5, 5.5 & 6 m suitable for classification K-7 & K-9 suitable for push-on-joint (rubber gusket D jointing) with cement mortar lining inside the pipes with outside zinc and bittuminous coating.Rates are ex factoryexcluding transpotion, taxes & duties, Contractor profit & overhead charges etc.Based on WPI 100.3 of May 2020(Including cost of one no. gasket for each pipe) |
| 459 | Note :(i)The rates are exfactory but exclusive of GST & C.P. based on WPI 100.3 of May 2020. (ii) Price variation of DI pipe will be calculated based on prevalling WPI. |
| 460 | Size class - K7 |
| 461 | 100 mm dia |
| 462 | 150 mm dia |
| 463 | 200 mm dia |
| 464 | 250 mm dia |
| 465 | 300 mm dia |
| 466 | 350 mm dia |
| 467 | 400 mm dia |
| 468 | 450 mm dia |
| 469 | 500 mm dia |
| 470 | 600 mm dia |
| 471 | 700 mm dia |
| 472 | 750 mm dia |
| 473 | 800 mm dia |
| 474 | 900 mm dia |
| 475 | 1000 mm dia |
| 476 | 1100 mm dia |
| 477 | 1200 mm dia |
| 478 | Size Class - K9 |
| 479 | 100 mm dia |
| 480 | 150 mm dia |
| 481 | 200 mm dia |
| 482 | 250 mm dia |
| 483 | 300 mm dia |
| 484 | 350 mm dia |
| 485 | 400 mm dia |
| 486 | 450 mm dia |
| 487 | 500 mm dia |
| 488 | 600 mm dia |
| 489 | 700 mm dia |
| 490 | 750 mm dia |
| 491 | 800 mm dia |
| 492 | 900 mm dia |
| 493 | 1000 mm dia |
| 494 | 1100 mm dia |
| 495 | 1200 mm dia |
| 496 | M1027Providing and Supplying of ISI standardDI specials & fitting with sealing rubber gasket of SBR, complete with cast Iron follower gland & MS nut bolts coated or otherwise protected from rusting and suitable for DI pipescomplete as per IS-9523 class K-12 ( ex factoryrates ) inspection charge transportation ,CP extra. |
| 497 | Socketed |
| 498 | 100 -150 mm dia |
| 499 | 200-300mm dia |
| 500 | 350-450mm dia |
| 501 | 500-600mm dia |
| 502 | 700 mm dia |
| 503 | 800 mm dia |
| 504 | 900 mm dia |
| 505 | 1000 mm dia |
| 506 | 1100 mm dia |
| 507 | 1200 mm dia |
| 508 | Flanged |
| 509 | 100 -150 mm dia |
| 510 | 200-300 mm dia |
| 511 | 350-450mm dia |
| 512 | 500-600mm dia |
| 513 | 700 mm dia |
| 514 | 800 mm dia |
| 515 | 900 mm dia |
| 516 | 1000 mm dia |
| 517 | 1100 mm dia |
| 518 | 1200 mm dia |
| 519 | M1028Providing and supplying in standard lengths High Density Polyethylene Pipe (HDPE Pipe) confirming to IS 4984-4984/14151/12786/13488 (Latest Revision with necessary jointing materials like mechanical connector i.e. thread/insert joint/quick release coupler joint/compression fitting joint or flanged joints excluding coupler/specials and taxes). |
| 520 | HDPE pipe of materials grade PE80-PN06 (dia in mm) |
| 521 | 25 mm dia |
| 522 | 32 mm dia |
| 523 | 40 mm dia |
| 524 | 50 mm dia |
| 525 | 63 mm dia |
| 526 | 75 mm dia |
| 527 | 90 mm dia |
| 528 | 110 mm dia |
| 529 | 125 mm dia |
| 530 | 140 mm dia |
| 531 | 160 mm dia |
| 532 | 180 mm dia |
| 533 | 200 mm dia |
| 534 | 225 mm dia |
| 535 | 250 mm dia |
| 536 | 280 mm dia |
| 537 | 315 mm dia |
| 538 | 355 mm dia |
| 539 | 400 mm dia |
| 540 | 450 mm dia |
| 541 | 500 mm dia |
| 542 | HDPE pipe of materials grade PE80-PN10 (dia in mm) |
| 543 | 25 mm dia |
| 544 | 32 mm dia |
| 545 | 40 mm dia |
| 546 | 50 mm dia |
| 547 | 63 mm dia |
| 548 | 75 mm dia |
| 549 | 90 mm dia |
| 550 | 110 mm dia |
| 551 | 125 mm dia |
| 552 | 140 mm dia |
| 553 | 160 mm dia |
| 554 | 180 mm dia |
| 555 | 200 mm dia |
| 556 | 225 mm dia |
| 557 | 250 mm dia |
| 558 | 280 mm dia |
| 559 | 315 mm dia |
| 560 | 355 mm dia |
| 561 | 400 mm dia |
| 562 | 450 mm dia |
| 563 | 500 mm dia |
| 564 | M1029Providing and supplying in standard lengths High Density Polyethylene Pipe (HDPE Pipe) 25mm to 500mm dia confirming to IS 4984-4984/14151/12786/13488 (Latest Revision with necessary jointing materials like mechanical connector i.e. thread/insert joint/quick release coupler joint/compression fitting joint or flanged joints excluding coupler/specials and taxes. |
| 565 | HDPE pipe of materials grade PE100-PN06 (dia in mm) |
| 566 | 25 mm dia |
| 567 | 32 mm dia |
| 568 | 40 mm dia |
| 569 | 50 mm dia |
| 570 | 63 mm dia |
| 571 | 75 mm dia |
| 572 | 90 mm dia |
| 573 | 110 mm dia |
| 574 | 125 mm dia |
| 575 | 140 mm dia |
| 576 | 160 mm dia |
| 577 | 180 mm dia |
| 578 | 200 mm dia |
| 579 | 225 mm dia |
| 580 | 250 mm dia |
| 581 | 280 mm dia |
| 582 | 315 mm dia |
| 583 | 355 mm dia |
| 584 | 400 mm dia |
| 585 | 450 mm dia |
| 586 | 500 mm dia |
| 587 | HDPE pipe of materials grade PE100-PN10 (dia in mm) |
| 588 | 25 mm dia |
| 589 | 32 mm dia |
| 590 | 40 mm dia |
| 591 | 50 mm dia |
| 592 | 63 mm dia |
| 593 | 75 mm dia |
| 594 | 90 mm dia |
| 595 | 110 mm dia |
| 596 | 125 mm dia |
| 597 | 140 mm dia |
| 598 | 160 mm dia |
| 599 | 180 mm dia |
| 600 | 200 mm dia |
| 601 | 225 mm dia |
| 602 | 250 mm dia |
| 603 | 280 mm dia |
| 604 | 315 mm dia |
| 605 | 355 mm dia |
| 606 | 400 mm dia |
| 607 | 450 mm dia |
| 608 | 500 mm dia |
| 609 | M1030RCC ESR |
| 610 | Designing (aesthetically), and constructing RCC elevated service reservoirs of following capacity with RCC staging Consisting of columns, internal and External bracings spaced vertically not More than 4.5 metres centre to centre for ESR having capacity upto 500 cum and Not more than 6m c/c for ESR having Capacity above 500 Cum including Excavation in all types of strata, foundation concrete, cement plaster with water proofing compound to the in side and out side face of the container and also plaster with plastic paint in all Columns and Bracingsincluding refilling disposing off the surplus stuff with in a lead of 50 metres, all labour and material charges including lowering, laying, erecting, hoisting and jointing of pipe assembly of inlet, outlet, washout, overflow and bypass arrangements as per departmental design, providing and fixing accessories such as M.S. ladder out side, Stainless Steel lader in contenor,C.I. manhole frame and covers, water level indicators,lightening conductor, G.I. pipe railing around walk way and top slab, providing stair case from ground level to roof level, M.S. Grill gate of 2M height with locking arrangement of approved design, B.B. Masonry chambers for all valves, ventilating shafts, providing and applying three coats of Acrylie emulsion with silicon edditives paint to the structure incluingroof slab, epoxy painting to internal surface and anti-termite treatment for under ground part soft he structure and giving satisfactory water tightness test as per I.S. code. The job to include painting then ame of the scheme and other details on thereservoir as per the directions of Engineer In - Charge. |
| 611 | Notes |
| 612 | The design of the structure be in accordance with relevant I.S. specification (I.S. 3370 - 1965 or revised.) |
| 613 | The design shall satisfy the stipulations as per I.S. 1893 -1984 and I.S.13920/1993 for seismic force and I.S.-11682 / 1985 for R.C.C. staging of over head tanks. |
| 614 | For design having more than 6 columns, suitable bracing is obligatory. |
| 615 | Plain round mild steel bars grade- I conforming to I.S.432 part-I orhigh yield strength deformed bars conforming to I.S. 1786 or I.S. 1139 shall beused, grade- I Imildsteel bars will not be allowed |
| 616 | Irrespective of the type of foundation proposed in the design, one set of bracing be provided at the ground level. |
| 617 | These rates include providing M.S. ladder for E.S.R.s upto 2 lakh litres capacity and providing spiral stair case for E.S.R. above 2 lakh litres capacity. |
| 618 | Staging shall have to bede signed with stresses of M-200 concrete for ESR. However all RCC construction should be donein M-250. Structures in contact with water shall be designed & casted in M-300 |
| 619 | These rates are including the cost of up lift pressure if any and entire dewatering during execution. Incase of water logging are a where water is struck at shallow depth, extra provision of dewatering shall be made as per site condition. |
| 620 | All conditions given in the Member Secretary\"s Circular No. MJP / TS-I / 350 / 1668 dt. 2-8-97 and MJP / S-I / 350 / 2127 dt. 13-7-99 shall be strictly followed and additional cost, if any, due to these conditions is included in the rates mentioned below. |
| 621 | 75 % part rate shall be payable for reinforcement concrete and plastering items of containers of E.S.R. till satisfactory hydraulic testing for water tightness is given; and till that work shall be treated as incomplete. |
| 622 | The rates indicated in the table are excluding the cost of pipes, specials and valves required for inlet, outlet, washout, overflow and bypass arrangement. The scope of work, however, includes cost of erecting, laying and jointing of pipe and valves including cost of jointing materials upto 5 M beyond outer face of outer most column ( Cost of pipe, specials and valves is taken as 10% of the cost of ESR as per table). |
| 623 | For ESR upto 500 cum capacity C.I. double flanged pipes upto 300 mm dia shall be provided and C.I. specials shall be used. For ESR above 500 cum capacity C.I. / M.S. pipe assembly with minimum 8 mm thickness upto 500 mm dia and minimum 10 mm thickness above 500 mm dia can be used with proper anti-corrosive epoxy treatment from in side and out side. |
| 624 | Below mentioned rates are for foundation swith individual footing with bearing capacity of 20 tonnes per square metre. For raft foundations, these rates shall be increased by 7.5% where safe bearing capacity (SBC) is 5 MT per sqm and by 5 % where SBC is more than 5MT / sqm and upto 10 MT / sqm. This % of5 % or 7. 5 % is applicable for estimation of amount of lumpsum item of ESR. For extra item due to change from individual foundation to raft, actual increase in concrete and steel be paid as per relevant DSR item. |
| 625 | The rate shall be increased by 30 % for bearing piles upto depth of 10 M and for further increased in depth by 5 M each, it shall be increased by another 10%. These rates are applicable where raft is not feasible. For pile foundations sulphate resistant cement shall only beused. Single pile for the column is not permitted, group of piles shall be designed with pile cap for each column of ESR. |
| 626 | The rates are applicable for staging height of 12 M. These rates shall be increased or decreased for per metre variation in this staging height as below : |
| 627 | 12 to 16 M staging - 2% per metre |
| 628 | 16 to 20 M staging - 3% per metre |
| 629 | 20 M and above - 4% per metre |
| 630 | For 17 M staging height, percentage calculation will be like below : |
| 631 | 12 to 16 M --- 4 x 2 = 8% |
| 632 | 16 & 17 M --- 1 x 3% = 3% Total = 11% |
| 633 | For 21 M staging height, percentage calculation will be like below : |
| 634 | 12 to 16 M --- 4 x 2 = 8% |
| 635 | 16 to 20 M --- 4 x 3% = 12% |
| 636 | 20& 21 M --- 1 x 4% = 4% Total = 24% |
| 637 | Following rates are for seismic zone III. For zone IV, these rates shall be increased by 5% and for zone II, these rates shall be decreased by 5%. Concerned Executive Engineer shall confirm the seismic zone for the scheme from seismic zone splan before estimation and adopt appropriate rates as per actual seismic zones. (Seismic maps attached in this CSR). |
| 638 | Notes |
| 639 | Conditions from Sr.No.1 to 10 shall form a part and parcel of the tender and must be included in the draft tender papers for works of R.C.C. E.S.R. |
| 640 | Conditions from Sr.No.11 to 16 are for estimation purpose only and shall not appear in the tender. |
| 641 | Rates for RCC ESRs |
| 642 | Upto 25,000 litres |
| 643 | Cost of 25,000 litres capacity |
| 644 | Add for capacity above 25,000 upto 50,000 litres |
| 645 | Cost of 50,000 litres capacity |
| 646 | Add for capacity above 50,000 upto 75,000 litres |
| 647 | Cost of 75,000 litres capacity |
| 648 | Add for capacity above 75,000 upto 1,00,000 litres |
| 649 | Cost of 1,00,000 litres capacity |
| 650 | Add for capacity above 1,00,000 upto 1,50,000 litres |
| 651 | Cost of 1,50,000 litres capacity |
| 652 | Add for capacity above 1,50,000 upto 2,00,000 litres |
| 653 | Cost of 2,00,000 litres capacity |
| 654 | Add for capacity above 2,00,000 upto 2,50,000 litres |
| 655 | Cost of 2,50,000 litres capacity |
| 656 | Add for capacity above 2,50,000 upto 3,00,000 litres |
| 657 | Cost of 3,00,000 litres capacity |
| 658 | Add for capacity above 3,00,000 upto 4,00,000 litres |
| 659 | Cost of 4,00,000 litres capacity |
| 660 | Add for capacity above 4,00,000 upto 5,00,000 litres |
| 661 | Cost of 5,00,000 litres capacity |
| 662 | Add for capacity above 5,00,000 upto 7,50,000 litres |
| 663 | Cost of 7,50,000 litres capacity |
| 664 | Add for capacity above 7,50,000 upto 10,00,000 litres |
| 665 | Cost of 10,00,000 litres capacity |
| 666 | Add for capacity above 10,00,000 upto 15,00,000 litres |
| 667 | Cost of 15,00,000 litres capacity |
| 668 | Add for capacity above 15,00,000 upto 20,00,000 litres |
| 669 | Cost of 20,00,000 litres capacity |
| 670 | M1031RCC GSR AND SUMP |
| 671 | Designing (aesthetically), and constructing RCC ground service reservoirs / RCC sumps in M-300 mix. of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top RCC roof slab / or dome, 20 mm thick cement plaster with water proofing compound in CM 1:3 proportion. to inside face of the container,including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bye-pass arrangement consisting of C.I./ M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as M.S. ladder inside and outside, C.I. Manhole frame and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coat of cement paints to all expose surface of structure including roof surface etc. complete as per design data, criteria, obligatory requirements and detailed specifications. |
| 672 | Anti –termite treatment shall be given for under ground portion of the structure. |
| 673 | Notes |
| 674 | The design shall be in accordance with various relevant I.S. specification (I.S.456/2000,I.S.875-1987,I.S.3370-1965 or revised.) |
| 675 | Only M.S. bars grade I conforming to I.S. 432 part-I or high yield strength deformed bars conforming to I.S. 1786 or I.S.1139 shall be used.Grade- II M.S. bars shall not be used. |
| 676 | Entire structure shall be in M-300 only. |
| 677 | The scope of pipe assembly work shall be upto 5 metre beyond out side face of the wall, cost of pipes valves and specials is not included in the rate but labour cost for laying and jointing is included. |
| 678 | The G.S.R. / Sump above 15 lakh litres capacity shall be in two compartment. |
| 679 | The Job includes designing the structure for up lift pressure and dewatering if required during entire execution and disposal of surplus excavated stuff within lead of 50 metres as directed by Engineer-in-charge. If up lifts considered in design, then these rates shall be increased by 7.5%. |
| 680 | G.S.R. outlets shall be with bell mouth of approved pattern in bottom slab and cost of designing bell mouth is included in the rate. Sump well includes cost of suction pit required at bottom. |
| 681 | For pipe diameters upto 300mm only CIpipes and CI specials shall be used. For pipe diameters above 300mm, M.S. pipes and specials minimum 10mm thick shall be used with proper anti corrosive epoxy treatment from inside and outside. |
| 682 | Cost of pump house is not included in these rates. |
| 683 | Above rates are applicable for Seismic Zones 2, 3 and 4. |
| 684 | 75% part rate shall be payable for reinforcement, concrete and plastering items of all types of G.S.R. sand sump still satisfactory hydraulic testing for water tightness test is given and till that work shall be treated as incomplete. |
| 685 | 10% shall be added for sump if over head pump house is proposed. |
| 686 | Note: Conditions from Sr.No.1 to 11 shall form a part and parcel of tender and must be included in the draft tender papers for work of R.C.C .GSRs and sumps. |
| 687 | Rates for RCC GSRs and Sumps |
| 688 | Upto 25,000 litres |
| 689 | Cost of 25,000 litres capacity |
| 690 | Add for capacity above 25,000 upto 50,000 litres |
| 691 | Cost of 50,000 litres capacity |
| 692 | Add for capacity above 50,000 upto 75,000 litres |
| 693 | Cost of 75,000 litres capacity |
| 694 | Add for capacity above 75,000 upto 1,00,000 litres |
| 695 | Cost of 1,00,000 litres capacity |
| 696 | Add for capacity above 1,00,000 upto 1,50,000 litres |
| 697 | Cost of 1,50,000 litres capacity |
| 698 | Add for capacity above 1,50,000 upto 2,00,000 litres |
| 699 | Cost of 2,00,000 litres capacity |
| 700 | Add for capacity above 2,00,000 upto 3,00,000 litres |
| 701 | Cost of 3,00,000 litres capacity |
| 702 | Add for capacity above 3,00,000 upto 5,00,000 litres |
| 703 | Cost of 5,00,000 litres capacity |
| 704 | Add for capacity above 5,00,000 upto 10,00,000 litres |
| 705 | Cost of 10,00,000 litres capacity |
| 706 | Addforcapacityabove10,00,000upto15,00,000 litres |
| 707 | Cost of 15,00,000 litres capacity |
| 708 | Add for capacity above 15,00,000 litres |
| 709 | Note: 10% shall be added over the cost of GSR for sump where over head pump house is proposed. |
| 710 | M1032UnconventionalWater Treatment Plant |
| 711 | Designing (aesthetically), providing and constructinghigh rate UnconventionalWaterTreatmentPlant i.e. Simplified Water Treatment Plant consisting of Civil works includingcostofprovidingandapplyingepoxypainttoinsidesurfaceofwaterretainingstructuresincontactwithchlorineandprovidinganti-termitetreatmenttoentirestructurebelowgroundlevel, ceramic tiles for floring, Acrylic emulsion with silicon additives paint from outside stainless steel railing, mechanicalandelectricalcomponentsofvarioussub-worksasgivenbelow : includingnecessaryhydraulic testing, structuraltesting and trial for 3 months, etc. completeas directedbyEngineer-in-charge (turn-key job) works. |
| 712 | Aeration fountain |
| 713 | Inlet arrangements |
| 714 | Mixing channel with ventury flume and flow measuring arrangement |
| 715 | Inlet channel |
| 716 | Flocculator- Conforming to I.S. 7208-1974 (Type-C) with detention period of 30 minutes |
| 717 | Tube settlers-Designing, fabricating and constructing Tube Settlers with square or any other shaped tube like Circular, Cheveron, Hexagonal etc .having proven performance |
| 718 | Rapid sand gravity filters - All valve shall be glandless. |
| 719 | Filter house |
| 720 | Chemical house |
| 721 | Alum tanks- 2Nos. with mixing, carrying and dosing arrangements with piping. |
| 722 | 100 kg chlorine cylender for capacity upto 5MLD and Chlorine tonner for capacity above 5 MLD. |
| 723 | TCL solution tank with mixing, carrying and dosing arrangement with piping. |
| 724 | Bypass arrangement |
| 725 | External and internal electrification |
| 726 | Laboratory equipments |
| 727 | Wash water tanks of capacity equal to12 minutes to wash specified number of filter beds at time at 600 lit / m2/m under head of 12m at under drain. |
| 728 | Wash water pumps with 100% standby |
| 729 | Air blowers capable of delivering 600 LMP per square metre of free air of filter area at 0.4 Kg / sqcm at the under drains (100 % standby).Air blowers shall be adopted for WTP having capacity more than 3 MLD only. Below 3 MLD capacity, Air blowers shall not be adopted. |
| 730 | Pure water sump of capacity equal to 1 hourpumping capacity. |
| 731 | Pure water pump house over the sump / by the side of sump. |
| 732 | Drainage arrangements |
| 733 | Alum store |
| 734 | Sanitary block with necessary water supply and drainage arrangements and internalWBM roads. |
| 735 | These rates are applicable for seismic zones 2, 3 and 4. |
| 736 | Rates given below are inclusive of uplift pressure if any and dewatering during the entire work. |
| 737 | All RCC structures shall be constructed in M-250. Structures in contact with water shall be in M-300. |
| 738 | Unconventional Treatment Plants less than 1 MLD capacity shall not be constructed. |
| 739 | All the Structural Steel Works / Fabrications are to be provided with application of Hot Dip Zinc coating according to specification as per IS 4759:1996 (Reafirmed 2006). |
| 740 | Note: Conditions from Sr. No. 1 to 28 shall form a part and parcel of the tender and must be included in draft tender papers for the work of unconventional treatment plants. |
| 741 | Unconventional Water Treatment Plant |
| 742 | Fixed cost for 1 MLD |
| 743 | Add for capacity above 1 MLD upto 2 MLD |
| 744 | Cost of 2 MLD treatment plant |
| 745 | Add for capacity above 2 MLD upto 3 MLD |
| 746 | Cost of 3 MLD treatment plant |
| 747 | M1033ConventionalWater Treatment Plant |
| 748 | Designing (aesthetically), providingconstructingandcommissioningConventionalWaterTreatmentPlantconsistingofallCivil, MechanicalandElectricalworks includingcostofprovidingandapplyingepoxypainttoinsidesurfaceofwaterretainingstructuresincontactwithchlorineandprovidingantitermitetreatmenttoentirestructurebelowgroundlevel,mechanicalandelectricalcomponentsofvarioussub-worksasgivenbelow, includingnecessaryhydraulic testing, structuraltesting, equipmenttestingandtrialrunfora periodof3 months, etc. completeas directedbyEngineer-in-charge (turn-key job). |
| 749 | Aeration Fountain- Plan are a not less than 0.625 square metre per MLD |
| 750 | Ventury Flume - With necessary devices, consisting of simple mechanical indicator. (Pedestal type gauge) |
| 751 | Flash Mixer-Rapid mixing device, detention time 60 seconds to give velocity gradient 300 to 400 sec -1, vane mixer type conforming to I.S. 7090 of 1985. |
| 752 | Flocculator – Conforming to I.S.7208-1974 (Type-C) with detention period of 30 minutes. |
| 753 | Clarifier - Horizontal flow circular tank, detention period 2-5 hours, overflow rate 30 cubic metre per square metre per day (to be specified), Weir loading not more than 300 cubic metre per metre per day, with mechanical sludge scraper conforming to I.S. No. 10313-1982. |
| 754 | Rapid Sand Filter sand Filter House-Filter designed for filteration rate of 5,000 litres per square metre per hour, minimum 2 beds for plant upto 10 MLD, for larger plants as specified, filters to be located in filter house with roof slab, pipe gallery and platform minimum 5.5 metre in width. |
| 755 | FilterSand-Effective size 0.45 to 0.70mm, uniformity coefficient not more than 1.7, nor less than 1.3, depth of water over sand 0.75M, free board 50cm, gravel 0.45M in depth, sand and gravel conforming to I.S. 8491 (i)-77, back wash by air wash, stand ard appurtenances (to be specified), rate of flow controller, filter gauge, sand expansion gauge, etc. |
| 756 | Wash Water Tank-Capacity to be specified and suitable to supply water to wash 2 filter units at a time where the units are 4 or more. |
| 757 | Wash Water Pumps- Capacity to fill water tank in 1 hour with 100% standby. |
| 758 | Air Blowers-Capable of delivering 600 LMP per square metre of free air, of filter area at 0.4kg / sqcm at the under drains (100% standby). |
| 759 | Chemical House in Two Storeys |
| 760 | Ground floor to accommodate 7 days\" alum requirement and sundry storage. |
| 761 | First floor to accommodate alum and lime tanks.etc. |
| 762 | Solution tanks-Minimum 3 tanks (one for preparation, second for dosing and third as standby), each tank capable of giving 8 hours maximum dose without interruption, minimum free board 0.30M, trays for dissolving, level indicator, mechanical agitation devices, solution feed and drain lines, solution feed device (constant head device, strength of solution upto 10% only) conforming to I.S. 9222 Part-I 1979. |
| 763 | Pure Water Sump and Sump House. |
| 764 | Capacity of sump – One hour of designed flow. |
| 765 | Pump House- Pump house of required size over the sump or by the side. |
| 766 | Store House-Suitable for alum storage of three months\" requirement in monsoon with 10% extra capacity for other sundry articles. |
| 767 | Vacuum feed type Chlorinators- Make tobe approved by MJP. |
| 768 | Conforming to I.S. 10533 - A Part-II 1983 |
| 769 | Rate for withdrawal |
| 770 | Temperature Kg. of Chlorine discharge Degree \"C\" per day (Cylinders) |
| 771 | 45 67Tonnes |
| 772 | 10 6.359.50 110 |
| 773 | 15 10.75 16.10130 |
| 774 | 20 14.50 21.24254 |
| 775 | 27&Above18.70 28.12315 |
| 776 | Chlorinator equipment and container room to conform to I.S. 10553 Part-I 1983. |
| 777 | 100% standby shall be provided. |
| 778 | By pass arrangements - C.I. or M.S. pipes. |
| 779 | Disposal of waste from WTP: Safe disposal arrangement to near by Nala including cost of pipe |
| 780 | For WTP of Capacity 30 MLD and more additional arrangement for backwash water recycle shall be provided, including sump, pupming machinary,rising main etc complete |
| 781 | Drainage arrangements – RCC pipes up to plot boundary. |
| 782 | Electrical installation – Both internal and external including entire plant area. |
| 783 | Laboratory equipment –As per requirement (to be specified during tendering). |
| 784 | Sanitary blocks – Carpet area -15 square metre minimum upto 25 Mld and 25 square metre above 25 Mld. |
| 785 | Administrative block and internal road-To accommodate office room, chlorine room, laboratory room, panel board room, blower room etc. and WBM road to connect all units from main gate of plot. |
| 786 | Rates given below are inclusive of up lift pressure if any and dewatering during entire work. |
| 787 | All pipes condutes channels with20%overloading |
| 788 | These rates are applicable for seismic zones 2, 3 and 4. |
| 789 | All RCC structures shall be constructed in M-300. |
| 790 | Note: Conditions from Sr. No. 1 to 22 shall form a part and parcel of the tender and must be incorporated in draft tender papers of conventional treatment plants (proposed). |
| 791 | Conventional Water Treatment Plant |
| 792 | Above3 MLD to Upto 5 MLD |
| 793 | Cost of 5 MLD treatment plant |
| 794 | Add for capacity above 5MLD upto 10 MLD |
| 795 | Cost of 10 MLD treatment plant |
| 796 | Add for capacity above 10 MLD upto20 MLD |
| 797 | Cost of 20 MLD treatment plant |
| 798 | Add for capacity above 20 MLD upto 50 MLD |
| 799 | Cost of 50 MLD treatment plant |
| 800 | Add for capacityabove 50 MLD upto 100 MLD |
| 801 | Cost of 100 MLD treatment plant |
| 802 | Add for capacity above 100 MLD |
| 803 | M1034GPT/HYGPT :Drilling by Rotary drill machine of size 300mm & 400mm dia with T.C. drill bit for tubewells in all kinds of soil including moorum, hard soil, soil mixed with pebbles, shingles, compacted soil, clay, soft and decomposed rock etc, up to 60 meters depth including reaming to facilitate smooth lowering of casing pipe etc. as per specification and direction of E/I (Basic rates) |
| 804 | 300 mm dia for GPT |
| 805 | 400 mm dia for HYGPT |
| 806 | M1035HYDT : Cost of drilling 200 mm x 165 mm x 125 meter deep bore well in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site (Basic rates) |
| 807 | From 0-50 meter |
| 808 | From 51-125 meter |
| 809 | M1036MS Pipe |
| 810 | Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc . all complete job(Basic rates) |
| 811 | Supplying all materia;ls, labours, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job(Basic rates) |
| 812 | M1037DT :Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and dirrection of Engineer Incharge (Basic rates) |
| 813 | Drillig upto 30 mtr Depth below G. L. in Rural Area |
| 814 | Drilling beyond 31 mtr upto 60 mtr below G. L. in Rural Area |
| 815 | M1038Trenchless |
| 816 | Installation of product pipe by manual pipe jacking method including making of entry and exit pits all related civil works like excavation ,shoring / strutting etc manual shielded excation ,lowering of pipe segments in the jacking pit laying and jointing of product pipeline through jacking process from the jacking pit and restoration of site after project completion as per the instruction of the engineering -in - charge all complete exept the cost of the pipe average cover of 1.5 depth below GI ( upto 100 meter installation length ) |
| 817 | from 900 mm to 1000 mm dia |
| 818 | In Soft soil |
| 819 | In Hard soil |
| 820 | In sandy Soil |
| 821 | In Stone Soil |
| 822 | from 1000 mm to 1200 mm dia |
| 823 | In Soft soil |
| 824 | In Hard soil |
| 825 | In sandy Soil |
| 826 | In Stone Soil |
| 827 | Above 1200 mm to 1500 mm dia |
| 828 | In Soft soil |
| 829 | In Hard soil |
| 830 | In sandy Soil |
| 831 | In Stone Soil |
| 832 | Installation of product pipe by Auger Boring methodincluding making of entry and exit pits all related civil works like excavation ,shoring/strutting etc shielded excavation ,through auger boring process lowering of pipe segments in the jacking pit laying and jointing of product pipeline through jacking process from the jacking pit and restoration of site after project completion as per the instruction of the engineering -in - charge all complete exept the cost of the pipe average cover of 1.5 depth below GI ( upto 100 meter installation length ) |
| 833 | upto 300 mm dia |
| 834 | In Soft soil |
| 835 | In Hard soil |
| 836 | In sandy Soil |
| 837 | In Stone Soil |
| 838 | Above300 mm to 450 mm dia |
| 839 | In Soft soil |
| 840 | In Hard soil |
| 841 | In sandy Soil |
| 842 | In Stone Soil |
| 843 | Above 450 mm to 600 mm dia |
| 844 | In Soft soil |
| 845 | In Hard soil |
| 846 | In sandy Soil |
| 847 | In Stone Soil |
| 848 | Above 600 mm to 900 mm dia |
| 849 | In Soft soil |
| 850 | In Hard soil |
| 851 | In sandy Soil |
| 852 | In Stone Soil |
| 853 | Installation of product pipe by Guided Auger Boring methodincluding making of entry and exit pits all related civil works like excavation ,shoring/strutting etc shielded excavation ,through auger boring process lowering of pipe segments in the jacking pit laying and jointing of product pipeline through jacking process from the jacking pit and restoration of site after project completion as per the instruction of the engineering -in - charge all complete exept the cost of the pipe average cover of 1.5 depth below GI ( upto 100 meter installation length ) |
| 854 | upto 300 mm dia |
| 855 | In Soft soil |
| 856 | In Hard soil |
| 857 | In sandy Soil |
| 858 | In Stone Soil |
| 859 | Above300 mm to 450 mm dia |
| 860 | In Soft soil |
| 861 | In Hard soil |
| 862 | In sandy Soil |
| 863 | In Stone Soil |
| 864 | Above 450 mm to 600 mm dia |
| 865 | In Soft soil |
| 866 | In Hard soil |
| 867 | In sandy Soil |
| 868 | In Stone Soil |
| 869 | Above 600 mm to 900 mm dia |
| 870 | In Soft soil |
| 871 | In Hard soil |
| 872 | In sandy Soil |
| 873 | In Stone Soil |
| 874 | M1039Providing and Supplying ISI Mark CI/ D/F reflux valves( Non return Valves ) of following dia inspection charges unloading from railway wagon ,loading into truck transportation upto department stores / site unloading stacking etc. complete reflux valve as per IS 5312 Part I (1984) |
| 875 | Without byepass arrangement - PN-1 |
| 876 | 50 MM |
| 877 | 65 MM |
| 878 | 80 MM |
| 879 | 100 MM |
| 880 | 125 MM |
| 881 | 150 MM |
| 882 | 200 MM |
| 883 | 250 MM |
| 884 | 300 MM |
| 885 | 350 MM |
| 886 | 400 MM |
| 887 | 450 MM |
| 888 | 500 MM |
| 889 | 600 MM |
| 890 | 700 MM |
| 891 | 750 MM |
| 892 | 800 MM |
| 893 | 900 MM |
| 894 | 1000 MM |
| 895 | 1100 MM |
| 896 | 1200 MM |
| 897 | With byepass arrangement - PN-1 |
| 898 | 50 MM |
| 899 | 65 MM |
| 900 | 80 MM |
| 901 | 100 MM |
| 902 | 125 MM |
| 903 | 150 MM |
| 904 | 200 MM |
| 905 | 250 MM |
| 906 | 300 MM |
| 907 | 350 MM |
| 908 | 400 MM |
| 909 | 450 MM |
| 910 | 500 MM |
| 911 | 600 MM |
| 912 | 700 MM |
| 913 | 750 MM |
| 914 | 800 MM |
| 915 | 900 MM |
| 916 | 1000 MM |
| 917 | 1100 MM |
| 918 | 1200 MM |
| 919 | Without byepass arrangement - PN-1.6 |
| 920 | 50 MM |
| 921 | 65 MM |
| 922 | 80 MM |
| 923 | 100 MM |
| 924 | 125 MM |
| 925 | 150 MM |
| 926 | 200 MM |
| 927 | 250 MM |
| 928 | 300 MM |
| 929 | 350 MM |
| 930 | 400 MM |
| 931 | 450 MM |
| 932 | 500 MM |
| 933 | 600 MM |
| 934 | With byepass arrangement - PN-1.6 |
| 935 | 50 MM |
| 936 | 65 MM |
| 937 | 80 MM |
| 938 | 100 MM |
| 939 | 125 MM |
| 940 | 150 MM |
| 941 | 200 MM |
| 942 | 250 MM |
| 943 | 300 MM |
| 944 | 350 MM |
| 945 | 400 MM |
| 946 | 450 MM |
| 947 | 500 MM |
| 948 | 600 MM |
| 949 | Providing double flange sluice valve ( Size 50 mm to 1200 mm ) confirming for IS - 2906 / 14846 including worn gear arrangements as per test pressure stailess steel spindle , caps transportation etc. all complete . |
| 950 | With byepass arrangement - PN-1 |
| 951 | 50 MM |
| 952 | 65 MM |
| 953 | 80 MM |
| 954 | 100 MM |
| 955 | 125 MM |
| 956 | 150 MM |
| 957 | 200 MM |
| 958 | 250 MM |
| 959 | 300 MM |
| 960 | 350 MM |
| 961 | 400 MM |
| 962 | 450 MM |
| 963 | 500 MM |
| 964 | 600 MM |
| 965 | 700MM |
| 966 | 750 MM |
| 967 | 800 MM |
| 968 | 900 MM |
| 969 | 1000 MM |
| 970 | 1100 MM |
| 971 | 1200MM |
| 972 | Without byepass arrangement - PN-1 |
| 973 | 50 MM |
| 974 | 65 MM |
| 975 | 80 MM |
| 976 | 100 MM |
| 977 | 125 MM |
| 978 | 150 MM |
| 979 | 200 MM |
| 980 | 250 MM |
| 981 | 300 MM |
| 982 | 350 MM |
| 983 | 400 MM |
| 984 | 450 MM |
| 985 | 500 MM |
| 986 | 600 MM |
| 987 | 700MM |
| 988 | 750 MM |
| 989 | 800 MM |
| 990 | 900 MM |
| 991 | 1000 MM |
| 992 | 1100 MM |
| 993 | 1200MM |
| 994 | Providing double flange sluice valve confirming for IS - 2906 / 14846 including worn gearas per test pressure stailess steel spindle , caps transportation etc. all complete FOR Rateincluding all taxes . . |
| 995 | Without byepass arrangement - PN-1.6 |
| 996 | 50 MM |
| 997 | 65 MM |
| 998 | 80 MM |
| 999 | 100 MM |
| 1000 | 125 MM |
| 1001 | 150 MM |
| 1002 | 200 MM |
| 1003 | 250 MM |
| 1004 | 300 MM |
| 1005 | 350 MM |
| 1006 | 400 MM |
| 1007 | 450 MM |
| 1008 | 500 MM |
| 1009 | 600 MM |
| 1010 | 700MM |
| 1011 | 750 MM |
| 1012 | 800 MM |
| 1013 | 900 MM |
| 1014 | 1000 MM |
| 1015 | 1100 MM |
| 1016 | 1200MM |
| 1017 | With byepass arrangement - PN-1.6 |
| 1018 | 50 MM |
| 1019 | 65 MM |
| 1020 | 80 MM |
| 1021 | 100 MM |
| 1022 | 125 MM |
| 1023 | 150 MM |
| 1024 | 200 MM |
| 1025 | 250 MM |
| 1026 | 300 MM |
| 1027 | 350 MM |
| 1028 | 400 MM |
| 1029 | 450 MM |
| 1030 | 500 MM |
| 1031 | 600 MM |
| 1032 | M1040Design and Supply of V -wire screen laterals suitable for infiltration Galleryas per site condition and detail provided End connection suitable flange excluding taxes and transportation . |
| 1033 | Dia - 06 inch ( 150 mm ) |
| 1034 | ID - 153 mm OD -167 mm |
| 1035 | Screen thickness - 07 mm |
| 1036 | Slot - 1.00 mm |
| 1037 | MOC - LowCarbon Galvenised steel |
| 1038 | Length - 5 mtr. |
| 1039 | Dia - 08 inch ( 200 mm ) |
| 1040 | ID - 205 mm OD -221mm |
| 1041 | Screen thickness - 08 mm |
| 1042 | Slot - 1.00 mm |
| 1043 | MOC - LowCarbon Galvenised steel |
| 1044 | Length - 5 mtr. |
| 1045 | Dia - 10 inch ( 250 mm ) |
| 1046 | ID - 256 mm OD -276mm |
| 1047 | Screen thickness - 10 mm |
| 1048 | Slot - 1.00 mm |
| 1049 | MOC - LowCarbon Galvenised steel |
| 1050 | Length - 5 mtr. |
| 1051 | Dia - 12 inch ( 300 mm ) |
| 1052 | ID - 306 mm OD -326 mm |
| 1053 | Screen thickness - 10 mm |
| 1054 | Slot - 1.00 mm |
| 1055 | MOC - LowCarbon Galvenised steel |
| 1056 | Length - 5 mtr. |
| 1057 | Dia - 14 inch ( 350 mm ) |
| 1058 | ID - 338 mm OD -363 mm |
| 1059 | Screen thickness - 12.5 mm |
| 1060 | Slot - 1.00 mm |
| 1061 | MOC - LowCarbon Galvenised steel |
| 1062 | Length - 5 mtr. |
| 1063 | M1041Supplying all materials, labours, equipments for lowering 125mm dia blue UPVC casing pipe as casing for protecting the sides from falling during the process of drilling all complete including carriage of materials to work site(Basic Rate). |
| 1064 | M1042Supplying all tools, equipments and labour and doing washing, flushing and development of drilled tube well to give clean and clear water all complete as per dirction E/I (Basic Rate). |
| 1065 | M1043Supplying labour cement and calcium chloride or bentonite solution and equipments for grouting the casing pipe after lowering in the bore including carriage of materials to work site etc. all complete as per specification & direction of E/I (Basic Rate). |
| 1066 | M1044Supplying labour and equipments including 125mm dia G.I. Cap and fitting and fixing over the casing pipe of tube well properly and taking it out as per direction E/I (The cap will be the property of department) (Basic Rate). |
| 1067 | M1045Supplying all materials, labours, equipments for constructing P.C.C. (1:2:4) circular platform around drilled tube well including 12mm thick cement plaster (1:4) with neat cement punning over exposed surface as per UNICEF design, etc. all complete including carriage of materials (Basic Rate). |
| 1068 | M1046Supplying all materials, labours and equipments for constructing P.C.C. (1:2:4) drain as per UNICEF design etc. all complete including carriage of materials (Basic Rate). |
| 1069 | M1047Supplying extra Deep well Hand Pump Complete sets with Cylinder Assembly & Connecting Rod (12 Pcs) as per IS : 15500 Part-2/2004(Basic Rate). |
| 1070 | M1048Supply of 200mm dia x 3.00m long UPVC casing pipe conferming to IS : 12818: 2016 (CML No. 5543459) latest revision including carrigae(Basic Rate). |
| 1071 | M1049Supply of 200mm dia ribbed Screen pipe conferming toIS : 12818: 2016 (CML No. 5543459) latest revision including carrigae(Basic Rate). |
| 1072 | M1050Supply of 125mm dia ribbed Screen pipe conferming toIS : 12818: 2016 (CML No. 5543459) latest revision including carrigae(Basic Rate). |
| 1073 | M1051Supplying all tools, equipments and labour and lowering 32 mm dia medium quality G.I. pipe in drilled tube well in 3 Mtrs. Length all complete as per dirction E/I including carriage of materials (Basic Rate). |
| 1074 | M1052Supplying all tools, Labour for fitting and fixing deep well cylinder with necessary connecting rod complete job as per specification & direction of E/I including carriage of materials (Basic Rate). |
| 1075 | M1053Supplying all materials, labours and fixing India mark II Hand Pump with all accessories all complete job as per direction of E/I including carriage of materials(Basic Rate). |
| 1076 | M1054Design, Supply, Installation testing & Commissioning of packaged water treatment plants (Unconventional type) of different capacity with (20 hours operation) comprising of lamella clarifier, Static Mixture Flocculation Tank (SMET), Multi grade filter (MGF) with best quality filter media, Lime/ coagulant/polymer dosing system hypo chloride dosing system, Raw water feed pump/clear water transfer pump (either or), sludge transfer cum recirculation pump, filter feed pump & back wash pump including all fitting like valve and other special fittings and electrical power supply to the different supplied units with MCB panel internal electrification with lighting arrangement with treatment plant site with provision of chemical storage and water testing boratoryfacility should be from a reputed manufacturer/ authorized distribution / authorized dealer conforming to relevant IS codes and certified by ISO-9001-2008 & 14001, It also include cost of civil foundation, including clarified water tank internal connecting pipe line from Raw Water inlet to CWR and applying internal epoxy paint on the supply equipment All the prices are exclusive of GST, Allied structure/items which are site specific such as external electrification, approach road, foot Bridge, cofferdam, compound wall, SCADA and automation, CWR pumps etc are to be considered extra. |
| 1077 | 0.2 MLD |
| 1078 | 0.3 MLD |
| 1079 | 0.4 MLD |
| 1080 | 0.5 MLD |
| 1081 | 0.6 MLD |
| 1082 | M1055PUMPS |
| 1083 | Supplying100 mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V+10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. |
| 1084 | Submersible Pump set 100 mm dia (with Polypropylene/ Noryl Impeller) up to 20 stages |
| 1085 | 1 H.P. |
| 1086 | 1.5HP |
| 1087 | 2 HP |
| 1088 | 2.5 HP |
| 1089 | 3.0 HP |
| 1090 | 4.0 HP |
| 1091 | 5.0 HP |
| 1092 | Supply rate should be increased by Rs 200/- per stage for pump with more than 20 stages |
| 1093 | Submersible Pump 150 mm dia (with Bronze impeller) up to 8 stages |
| 1094 | 1.5 HP |
| 1095 | 2.0 HP |
| 1096 | 3.0 HP |
| 1097 | 4.0 HP |
| 1098 | 5.0 HP |
| 1099 | 6.0 HP |
| 1100 | 7.5 HP |
| 1101 | Supply rate should be increased by Rs 600/- per stage for pump with more than 8 stages |
| 1102 | Submersible Pump 150 mm dia (with Bronze Impeller) up to 12 stages |
| 1103 | 8.0 HP |
| 1104 | 9.0 HP |
| 1105 | 10.0 HP |
| 1106 | 11.0 HP |
| 1107 | 12.5 HP |
| 1108 | 15.0 HP |
| 1109 | Supply rate should be increased by Rs 600/- per stage for pump with more than 12 stages |
| 1110 | Submersible Pump 150 mm dia (with Bronze Impeller) up to 20 stages |
| 1111 | 17.5 HP |
| 1112 | 20.0 HP |
| 1113 | 25 HP |
| 1114 | 1) Supply rate should be increased by Rs 600/- per stage for pump with more than 20 stages for Bore well only. |
| 1115 | For other use 200 mm dia pump shall be preferred over 150 mm dia with more than 20 stage pump. |
| 1116 | 2) For 150 mm dia energy efficient pumps add as below |
| 1117 | a. up to 8 stages :- 3% on supply rate |
| 1118 | b. up to 12 stages :- 4% on supply rate |
| 1119 | c. up to 15 stages :- 5% on supply rate |
| 1120 | M1056PRESSURE GAUGE |
| 1121 | Providing fabricating, testing and commisioning pressure vessel fabricating in M.S plate on providing foundation including epoxy paint |
| 1122 | Pressure gauge (100 mm dia) |
| 1123 | Pressure gauge (150 mm dia) |
| 1124 | Vacuum / Combination gauge |
| 1125 | SupplyingVacuum Gauge/ Combination gauge of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I. pipe. |
| 1126 | Vacuum / Combination gauge – 100 mm dia |
| 1127 | Vacuum / Combination gauge – 150 mm dia |
| 1128 | M1057Lifting Equipment |
| 1129 | Chain pulley Block |
| 1130 | Supplyingtriple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. |
| 1131 | 1 Tonne Capacity |
| 1132 | 2 Tonne Capacity |
| 1133 | 3 Tonne Capacity |
| 1134 | Hand operated Circular or Rectangular Travelling Crane (Single Girder) |
| 1135 | SupplyingSingle Girder Hand Operated Circular/ Rectangular Travelling Crane with 6 m lift complete with chain pulley block ISI marked and travelling trolley both tested for 50% overload including arrangement for longitudinal travel / circular travel and cross travel with wheel, hand chain, etc complete. |
| 1136 | 3 Tonne Capacity |
| 1137 | Up to 5 m span |
| 1138 | Above 5 m up to 6 m span |
| 1139 | Above 6 m up to 8 m span |
| 1140 | 5 Tonne Capacity |
| 1141 | Up to 5 m span |
| 1142 | Above 5 m up to 6 m span |
| 1143 | Above 6 m up to 8 m span |
| 1144 | Above 8 m up to 10 m span |
| 1145 | Electric Operated Circular or Rectangular Travelling Crane (Single Girder) |
| 1146 | Supplying single girder Electrically Operated Rectangular Over head Travelling Crane with 6 m lift complete with wire rope hoist, class II duty, all three motions electrically operated by suitable rating motor IP 54, control panel and down pendant control block. |
| 1147 | 5 Tonne Capacity |
| 1148 | Above 6 m up to 8 m span |
| 1149 | Above 8 m up to 10 m span |
| 1150 | 7.5 Tonne Capacity |
| 1151 | Above 6 m upto 8 m span |
| 1152 | Above 8 m up to 10 m span |
| 1153 | 10 Tonne Capacity |
| 1154 | Above 6 m up to 8 m span |
| 1155 | Above 8 m up to 10 m span |
| 1156 | Square Bar / Rail |
| 1157 | Providing, erecting and fixing square bar of EN 8 as rail for over head crane on provided track, girder / continuous corbel beam, including supporting plate and “J” bolts. |
| 1158 | 50 X 50 mm (EN 8) |
| 1159 | 40 X 40 mm (EN 8) |
| 1160 | M1058Lightening Arrester, AB Switch, Insulators |
| 1161 | Lightening Arrestor |
| 1162 | Supplying, erecting approved make thyrite type Lightening Arrestor suitable for H.T. supply with necessary ancillary material complete on provided cross arm and connected to overhead line. |
| 1163 | Suitable for 11 kV Supply, Distribution class |
| 1164 | Suitable for 22 kV Supply, Distribution class |
| 1165 | Suitable for 33 kV Supply, Station class |
| 1166 | Disc Insulator |
| 1167 | Supplying, erecting porcelain Disc Type Insulators with hardware fittings suitable for H.T. overhead line complete erected with nuts and bolts on provided cross arm |
| 1168 | Suitable for 11KV line |
| 1169 | Suitable for 33KV line |
| 1170 | Pin Insulator |
| 1171 | Supplying, erecting porcelain Pin Type Insulators with hardware fittings suitable for H.T. overhead line complete erected with nuts and bolts on provided cross arm |
| 1172 | Suitable for 11KV line |
| 1173 | Suitable for 33KV line |
| 1174 | Air break switch without Earth switch |
| 1175 | Supplying, erecting approved make H.T. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground with necessary clamps |
| 1176 | Suitable for 11KV line |
| 1177 | Rocking / Tilting type |
| 1178 | Rotating type |
| 1179 | Suitable for 33KV line |
| 1180 | Rocking / Tilting type |
| 1181 | Rotating type |
| 1182 | Air break switch with Earth switch |
| 1183 | Supplying, erecting approved make H.T. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground with necessary clamps |
| 1184 | Suitable for 11KV line |
| 1185 | Rotating type |
| 1186 | Suitable for 33KV line |
| 1187 | Rotating type |
| 1188 | Drop out Fuse (channel mounted) |
| 1189 | Supplying, erecting approved make out door type Drop out fuse channel type with insulator complete with fuse holders fuse barrel with metal fittings, fuse element, with working currentup to 50 Amp, capacity completeerected on provided cross arm, each set comprising 3 units |
| 1190 | Suitable for 11 KV line |
| 1191 | Suitable for 33 KV line |
| 1192 | Horn gap fuse (channel mounted) |
| 1193 | Supplying, erecting approved make out door type Horn gap type fuse with insulator, fuse element, with working current up to 50 Amp, capacity complete erected on provided cross arm, each set comprising 3 units |
| 1194 | Suitable for 11 KV line |
| 1195 | Suitable for 33 KV line |
| 1196 | M1059TRANSFORMER |
| 1197 | Power Transformer (with off load Tap changer) Any ISI Mark |
| 1198 | Supplyingoutdoor type copper wound transformer continuously rated for 3Ph, 50 Hz, at full load and temp. rise not exceeding 450 C by thermometer in oil and 500 C by theresistance in winding after continuous run at full load rating, thetransformer should have oil immersed winding having vector group DY11, HT side connected in delta and LT side connected in star with neutral brought out connected to provideseparateearthing. The Transformer shall have power terminal arrangement, bushing/ cable end box on HT side and cable end box on LT side. 2 Nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the transformer. The transformer should have following standard fittings. Transformer shall be latest manufacturing standards as per amended IS specifications and the load & No load losses shall be limited to the values given below or as per IS or Norms issued by SEB which ever are lower- |
| 1199 | 1. Oil conservator with filling hole with cap and plain oil level gauge. |
| 1200 | 2. Silica gel dehydrating breather charged with silica gel. |
| 1201 | 3. Oil drain valve |
| 1202 | 4. Oil filter valve |
| 1203 | 5. Lifting eyes/ hooks |
| 1204 | 6. Two earthing terminals |
| 1205 | 7. Diagram and rating plate |
| 1206 | 8. Air vent |
| 1207 | 9. Explosion vent |
| 1208 | 10. 100mm dia thermo meter with thermometer pocket |
| 1209 | 11. Four bi directional plain roller. |
| 1210 | Power Transformer 11000/433 volts With off load Tap Changer – 12.5% to +2.5% in steps of 2.5% as per BIS Level-2. |
| 1211 | 63 KVA ( No load loss 180w and load loss 1235w) |
| 1212 | 100 KVA (No load loss 260w and load loss 1760w) |
| 1213 | 160KVA (No load loss 260w and load loss 1760w) |
| 1214 | 200KVA(No load loss 500w and load loss3000w) |
| 1215 | 250KVAA(No load loss 550w and load loss3600w) |
| 1216 | 315KVA (No load loss 580w and load loss 4200w) |
| 1217 | 400 KVA (No load loss 715w and load loss 5000w) |
| 1218 | 500 KVA (No load loss 850w and load loss 5800w) |
| 1219 | 630 KVA (No load loss 1000w and load loss 7000w) |
| 1220 | 750 KVA (No load loss 1500w and load loss 8000w) |
| 1221 | Power Transformer (with on load Tap changer) |
| 1222 | Supplyingoutdoor type copper wound transformer continuously rated for 3Ph, 50 Hz, at full load and temp. rise not exceeding 450 C by thermometer in oil and 500 C by theresistance in winding after continuous run at full load rating, thetransformer should have oil immersed winding having vector group DY11, HT side connected in delta and LT side connected in star with neutral brought out connected to provideseparateearthing. The Transformer shall have power terminal arrangement, bushing/ cable end box on HT side and cable end box on LT side. 2Nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the transformer. The transformer should have following standard fittings. The OLTC should be suitable for minimum 50 operations per day. Transformer shall be latest manufacturing standards as per amended IS specifications and the load & No load losses shall be limited to the values given below or as per IS or Norms issued by SEB which ever are lower- |
| 1223 | 1. Oil conservator with filling hole with cap and plain oil level gauge. |
| 1224 | 2. Silica gel dehydrating breather charged with silica gel. |
| 1225 | 3. Oil drain valve |
| 1226 | 4. Oil filter valve |
| 1227 | 5. Lifting eyes/ hooks |
| 1228 | 6. Two earthing terminals |
| 1229 | 7. Diagram and rating plate |
| 1230 | 8. Air vent |
| 1231 | 9. Explosion vent |
| 1232 | 10. 100mm dia thermo meter with thermometer pocket |
| 1233 | 11. Four bi directional plain roller. |
| 1234 | 12. Buchholz relay |
| 1235 | 13. Resistance Temp. detector |
| 1236 | 14. Marshalling box |
| 1237 | 15. Automatic Voltage Regulator (AVR) |
| 1238 | 16. Remote Tap Changing Controller (RTCC) |
| 1239 | Transformer 11000/433 volts Withon load Tap Changer – 15% to +5% in steps of 1.25% with RTCC, AVR and marshalling box and other specification as per BIS Level-2. |
| 1240 | 750 KVA |
| 1241 | 1000 KVA |
| 1242 | 1250 KVA |
| 1243 | 1600 KVA |
| 1244 | 2000 KVA |
| 1245 | M1060Motors |
| 1246 | Foot Mounted Motors TEFC 1500 RPM |
| 1247 | SupplyingFoot Mounted TEFC 1500 RPM, squirrel cage induction motor, conforming to IS 325 having continuous rating suitable for operation at 415 volts +/-10%, 3 Phase, 50 HZ +/-3% with “F” class insulation temperature rise limited to class “B” insulation. Motors conform to IS-12615 with efficiency level IE3 and provided with enclosure protection class IP-55. |
| 1248 | 15 KW (20 HP) |
| 1249 | 18.5 KW ( 25 HP) |
| 1250 | 22 KW ( 30 HP) |
| 1251 | 30 KW ( 40 HP) |
| 1252 | 37 KW ( 50 HP) |
| 1253 | 45 KW ( 60 HP) |
| 1254 | 55 KW ( 75 HP) |
| 1255 | 75 KW ( 100 HP) |
| 1256 | 90 KW ( 120 HP) |
| 1257 | 110 KW ( 150 HP) |
| 1258 | 132KW(180HP) |
| 1259 | 160KW( 215 HP) |
| 1260 | 250KW (335 HP) |
| 1261 | Foot Mounted Motor TEFC 1500 RPM |
| 1262 | 0.75 KW(1HP) |
| 1263 | 1.1 KW ( 1.5 HP) |
| 1264 | 1.5 KW ( 2 HP) |
| 1265 | 2.2 KW ( 3 HP) |
| 1266 | 3.7 KW ( 5 HP) |
| 1267 | 5.5 KW ( 7.5 HP) |
| 1268 | 7.5 KW ( 10 HP) |
| 1269 | 9.3 KW ( 12.5 HP) |
| 1270 | 11 KW ( 15 HP) |
| 1271 | M1061Aluminium Cable |
| 1272 | CABLE |
| 1273 | Aluminium conductor three core, XLPE / PVC insulated & armoured cable . |
| 1274 | SupplyingXLPE / PVC insulated, armoured cable 1100 V grade with ISI mark Three core, solid / stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete in an approved manner. |
| 1275 | 3 core 2.5 sq mm |
| 1276 | 3 core 4 sq mm |
| 1277 | 3 core 6 sq mm |
| 1278 | 3 core 10 sq mm |
| 1279 | 3 core 16 sq mm |
| 1280 | 3 core 25 sq mm |
| 1281 | 3 core 35 sq mm |
| 1282 | 3 core 50 sq mm |
| 1283 | 3 core 70 sq mm |
| 1284 | 3 core 95 sq mm |
| 1285 | 3 core 120 sq mm |
| 1286 | 3 core 150 sq mm |
| 1287 | 3 core 185 sq mm |
| 1288 | 3 core 240 sq mm |
| 1289 | 3 core 300 sq mm |
| 1290 | 3 core 400 sq mm |
| 1291 | Aluminium conductor 3.5 core, XLPE / PVC insulated & unarmoured cable |
| 1292 | SupplyingXLPE / PVC insulated, unarmoured cable 1100 V grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, completein an approved manner. |
| 1293 | 3.5 core 25 sq mm |
| 1294 | 3.5 core 35 sq mm |
| 1295 | 3.5 core 50 sq mm |
| 1296 | 3.5 core 70 sq mm |
| 1297 | 3.5 core 95 sq mm |
| 1298 | 3.5 core 120 sq mm |
| 1299 | 3.5 core 150 sq mm |
| 1300 | 3.5 core 185 sq mm |
| 1301 | 3.5 core 240 sq mm |
| 1302 | 3.5 core 300 sq mm |
| 1303 | 3.5 core 400 sq mm |
| 1304 | HT Aluminium three core 3.3 KVE cable XLPE insulated |
| 1305 | Supplying HT Aluminium three core cable XLPE insulated ,insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.) cores laidup inner sheath of PVC tape ,galvanised steel flat strip armoured,and overall PVC sheathed cable conforming to IS :7098 /II/85 with latest amendments |
| 1306 | 3 core 35 sq mm |
| 1307 | 3 core 50 sq mm |
| 1308 | 3 core 70 sq mm |
| 1309 | 3 core 95 sq mm |
| 1310 | 3 core 120 sq mm |
| 1311 | 3 core150sq mm |
| 1312 | 3 core 185 sq mm |
| 1313 | 3 core 240sq mm |
| 1314 | 3 core 300 sq mm |
| 1315 | 3 core 400 sq mm |
| 1316 | HT Aluminium three core 6.6 KV(UE)/11KV Ecable XLPE insulated |
| 1317 | Supplying HT Aluminium three core cable XLPE insulated ,insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.) cores laidup inner sheath of PVC tape ,galvanised steel flat strip armoured,and overall PVC sheathed cable conforming to IS :7098 /II/85 with latest amendments |
| 1318 | 3 core 35 sq mm |
| 1319 | 3 core 50 sq mm |
| 1320 | 3 core 70 sq mm |
| 1321 | 3 core 95 sq mm |
| 1322 | 3 core 120 sq mm |
| 1323 | 3 core150sq mm |
| 1324 | 3 core 185 sq mm |
| 1325 | 3 core 240sq mm |
| 1326 | 3 core 300 sq mm |
| 1327 | 3 core 400 sq mm |
| 1328 | HT Aluminium three core 11KV(UE) cable XLPE insulated |
| 1329 | Supplying HT Aluminium three core cable XLPE insulated ,insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.) cores laidup inner sheath of PVC tape ,galvanised steel flat strip armoured,and overall PVC sheathed cable conforming to IS :7098 /II/85 with latest amendments |
| 1330 | 3 core 35 sq mm |
| 1331 | 3 core 50 sq mm |
| 1332 | 3 core 70 sq mm |
| 1333 | 3 core 95 sq mm |
| 1334 | 3 core 120 sq mm |
| 1335 | 3 core150sq mm |
| 1336 | 3 core 185 sq mm |
| 1337 | 3 core 240sq mm |
| 1338 | 3 core 300 sq mm |
| 1339 | 3 core 400 sq mm |
| 1340 | Aluminium conductor three core, XLPE / PVC insulated & unarmoured cable . |
| 1341 | SupplyingXLPE / PVC insulated, unarmoured cable 1100 V grade with ISI mark Three core, solid / stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete in an approved manner. |
| 1342 | 3 core 4 sq mm |
| 1343 | 3 core 6 sq mm |
| 1344 | 3 core 10 sq mm |
| 1345 | 3 core 16 sq mm |
| 1346 | 3 core 25 sq mm |
| 1347 | 3 core 35 sq mm |
| 1348 | 3 core 50 sq mm |
| 1349 | 3 core 70 sq mm |
| 1350 | 3 core 95 sq mm |
| 1351 | 3 core 120 sq mm |
| 1352 | 3 core 150 sq mm |
| 1353 | 3 core 185 sq mm |
| 1354 | 3 core 240 sq mm |
| 1355 | 3 core 300 sq mm |
| 1356 | 3 core 400 sq mm |
| 1357 | M1062Copper Cable |
| 1358 | CABLE |
| 1359 | 3 Core PVC insulated, PVC sheathed copper conductor flat submersible cable . |
| 1360 | Supplying , Flat flexible submersible cable with, copper conductor, PVC insulated, and PVC sheathed . |
| 1361 | 3 core 1.5 sq mm |
| 1362 | 3 core 2.5 sq mm |
| 1363 | 3 core 4 sq mm |
| 1364 | 3 core 6 sq mm |
| 1365 | 3 core 10 sq mm |
| 1366 | 3 core 16 sq mm |
| 1367 | 3 core 25 sq mm |
| 1368 | 3 core 35 sq mm |
| 1369 | Copper conductor three core, XLPE / PVC insulated & unarmoured cable . |
| 1370 | SupplyingXLPE / PVC insulated, unarmoured cable 1100 V grade with ISI mark Three core, solid / stranded copper conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete in an approved manner. |
| 1371 | 3 core 1.5 sq mm |
| 1372 | 3 core 2.5 sq mm |
| 1373 | 3 core 4 sq mm |
| 1374 | 3 core 6 sq mm |
| 1375 | 3 core 10 sq mm |
| 1376 | 3 core 16 sq mm |
| 1377 | 3 core 25 sq mm |
| 1378 | 3 core 35 sq mm |
| 1379 | 3 core 50 sq mm |
| 1380 | 3 core 70 sq mm |
| 1381 | 3 core 95 sq mm |
| 1382 | Copper conductor 3.5 core, XLPE / PVC insulated & armoured cable . |
| 1383 | SupplyingXLPE / PVC insulated, armoured cable 1100 V grade with ISI mark 3.5 core, solid / stranded copper conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, completein an approved manner. |
| 1384 | 3.5 core 1.5 sq mm |
| 1385 | 3.5 core 2.5 sq mm |
| 1386 | 3.5 core 4 sq mm |
| 1387 | 3.5 core 6 sq mm |
| 1388 | 3.5 core 10 sq mm |
| 1389 | 3.5 core 16 sq mm |
| 1390 | 3.5 core 25 sq mm |
| 1391 | 3.5 core 35 sq mm |
| 1392 | 3.5 core 50 sq mm |
| 1393 | 3 .5 core 70 sq mm |
| 1394 | 3.5 core 95 sq mm |
| 1395 | 3.5 core 120 sq mm |
| 1396 | 3 .5 core150sq mm |
| 1397 | 3.5 core 185 sq mm |
| 1398 | 3.5 core 240sq mm |
| 1399 | 3.5 core 300 sq mm |
| 1400 | 3.5 core 400 sq mm |
| 1401 | copper conductor 3.5 core XLPE/PVCunarmoured |
| 1402 | SupplyingXLPE / PVC insulated, unarmoured cable 1100 V grade with ISI mark 3.5 core, solid / stranded copper conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete in an approved manner. |
| 1403 | 3.5core 25 sq mm |
| 1404 | 3.5core 35 sq mm |
| 1405 | 3.5 core 50 sq mm |
| 1406 | 3.5 core 70 sq mm |
| 1407 | 3.5 core 95 sq mm |
| 1408 | 3.5 core 120 sq mm |
| 1409 | 3.5 core150sq mm |
| 1410 | 3.5 core 185 sq mm |
| 1411 | 3.5 core 240sq mm |
| 1412 | 3.5 core 300 sq mm |
| 1413 | 3.5 core 400 sq mm |
| 1414 | Copper conductor three core, XLPE / PVC insulated & armoured cable . |
| 1415 | SupplyingXLPE / PVC insulated, armoured cable 1100 V grade with ISI mark Three core, solid / stranded copper conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete in an approved manner. |
| 1416 | 3 core 1.5 sq mm |
| 1417 | 3 core 2.5 sq mm |
| 1418 | 3 core 4 sq mm |
| 1419 | 3 core 6 sq mm |
| 1420 | 3 core 10 sq mm |
| 1421 | 3 core 16 sq mm |
| 1422 | 3 core 25 sq mm |
| 1423 | 3 core 35 sq mm |
| 1424 | 3 core 50 sq mm |
| 1425 | 3 core 70 sq mm |
| 1426 | 3 core 95 sq mm |
| 1427 | 3 core 120 sq mm |
| 1428 | 3 core 150sq mm |
| 1429 | 3core 185 sq mm |
| 1430 | 3 core 240 sq mm |
| 1431 | 3 core 300 sq mm |
| 1432 | 3 core 400 sq mm |
| 1433 | M1063FOOT VALVE |
| 1434 | Foot valve |
| 1435 | Supplying C.I. foot valve having single leather flap and gunmetal seating. Valve shall be fixed on suction side of pump as per requirement including jointing material and hardware. |
| 1436 | Flanged type |
| 1437 | 50 mm |
| 1438 | 65 mm |
| 1439 | 80 mm |
| 1440 | 100 mm |
| 1441 | 125 mm |
| 1442 | 150 mm |
| 1443 | M1064AirCircuit Breaker |
| 1444 | ACBbreaking capacity 50kA Thermal Magnetic Manual draw Out type 3 pole |
| 1445 | 630A |
| 1446 | 800A |
| 1447 | 1000A |
| 1448 | 1250A |
| 1449 | 1600A |
| 1450 | 2000A |
| 1451 | M1065STARTER |
| 1452 | D.O.L. starter with SS Enclosure with 380/415 Volt coil |
| 1453 | 7.5 H.P. |
| 1454 | 10 H.P. |
| 1455 | SupplyingFully automatic star delta starter to operate induction motor working on415v,3phase,50 hz with no volt coil, Over load element, ON-OFF push buttons, with necessary materials and connected to supply, etc complete starter with original sheet steel encloser |
| 1456 | F.A.S.D starter |
| 1457 | 10.0 H.P. |
| 1458 | 15 H.P. |
| 1459 | 20 H.P. |
| 1460 | 25 H.P. |
| 1461 | 35 H.P. |
| 1462 | 40 HP |
| 1463 | 50 HP |
| 1464 | 75 H.P. |
| 1465 | 100 H.P. |
| 1466 | 125 H.P. |
| 1467 | 150 H.P. |
| 1468 | 250 H.P. |
| 1469 | M1066Servo Controlled Automatic Voltage Stabilizer |
| 1470 | Providing, erecting Servo Controlled Automatic Voltage stabiliser suitable for out put voltage of 415 Volt +/-1%, 3 Ph, 50 Hz, with copper wound transformer (air/oil cooled) as mentioned below. The stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%. The stabilizer should be constructed in cubical box, with bidirectional wheels for easy handling, necessary monitors and user\"s controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and out put voltage, Auto/Manual selector switch, Raise/Low push buttons etc. Suitable capacity termination strips and bus bars for incoming and out going cable should be provided. All three phases shall be independently monitored and corrected. Following protections and indications shall be incorporated?? Over Voltage / Under Voltage?? Single Phasing?? Cut off contactor with electronic output sensing unit |
| 1471 | Servo Controlled Automatic Voltage Stabiliser(Out put 415 +/-1%)Input 150 to 450 Volt |
| 1472 | 20 kVA Air cooled |
| 1473 | 25 kVA Air cooled |
| 1474 | 30 kVA Air cooled |
| 1475 | 40 kVA Air cooled |
| 1476 | 50 kVA Oil cooled |
| 1477 | 60 kVA Oil cooled |
| 1478 | 75 kVA Oil cooled |
| 1479 | 100 kVA Oil cooled |
| 1480 | 125 kVA Oil cooled |
| 1481 | Servo Controlled Automatic Voltage Stabiliser (Out put 415 +/-1%) Input 280 to 460 Volt |
| 1482 | 15 KVA Air cooled |
| 1483 | 20 KVA Air cooled |
| 1484 | 25 KVA Air cooled |
| 1485 | 30 KVA Air cooled |
| 1486 | 40 kVA Air cooled |
| 1487 | 50KVA Air cooled |
| 1488 | 60 KVA Oil cooled |
| 1489 | 75KVA Oil cooled |
| 1490 | 100 KVA Oil cooled |
| 1491 | 125 kVA Oil cooled |
| 1492 | 150 KVA oil cooled |
| 1493 | 200KVA oil cooled |
| 1494 | 250KVA oil cooled |
| 1495 | 300 KVA oil cooled |
| 1496 | 400 KVA oil cooled |
| 1497 | M1067Termination Kit |
| 1498 | Providing and errecting IN-DOOR type termination kit, for 3.3kV/ 6.6 kV / 11kV/ 22kV/33kV XLPE Screened 3 core cable |
| 1499 | IN-DOOR Termination KIT for 3.3kV(E/UE) / 6.6 kV(E) XLPE 3 core cable |
| 1500 | 25-50 mm2 |
| 1501 | 70-120 mm2 |
| 1502 | 150-185 mm2 |
| 1503 | 240-400 mm2 |
| 1504 | OUT-DOOR Termination KIT for 3.3(E/UE)/6.6 KV(E) XLPE 3 core cable |
| 1505 | 25-50 mm2 |
| 1506 | 70-120 mm2 |
| 1507 | 150-185 mm2 |
| 1508 | 240-400 mm2 |
| 1509 | Straight through Joint for 3.3KV(E/UE)/ 6.6 KV(E) XLPE 3 core cable |
| 1510 | 25-50 mm2 |
| 1511 | 70-120 mm2 |
| 1512 | 150-185 mm2 |
| 1513 | 240-300 mm2 |
| 1514 | IN DOOR Termination KIT for 11KV(E) XLPE Screened 3 core cable |
| 1515 | 25-50 mm2 |
| 1516 | 70-120 mm2 |
| 1517 | 150-185 mm2 |
| 1518 | 240-400 mm2 |
| 1519 | OUT DOOR Termination KIT for 11KV(E) XLPE Screened 3 core cable |
| 1520 | 25-50 mm2 |
| 1521 | 70-120 mm2 |
| 1522 | 150-185 mm2 |
| 1523 | 240-400 mm2 |
| 1524 | Straight through Joint for 11 KV(E) XLPE Screened 3 core cable |
| 1525 | 25-50 mm2 |
| 1526 | 70-120 mm2 |
| 1527 | 150-185 mm2 |
| 1528 | 240-300 mm2 |
| 1529 | IN DOOR Termination KIT for 22KV(E) XLPE Screened 3 core cable |
| 1530 | 25-50 mm2 |
| 1531 | 70-120 mm2 |
| 1532 | 150-185 mm2 |
| 1533 | 240-400 mm2 |
| 1534 | OUT DOOR Termination KIT for 22KV(E) XLPE Screened 3 core cable |
| 1535 | 25-50 mm2 |
| 1536 | 70-120 mm2 |
| 1537 | 150-185 mm2 |
| 1538 | 240-400 mm2 |
| 1539 | Straight through Joint for 22 KV(E) XLPE Screened 3 core cable |
| 1540 | 25-50 mm2 |
| 1541 | 70-95 mm2 |
| 1542 | 120-150 mm2 |
| 1543 | 185-240 mm2 |
| 1544 | 300-400 mm2 |
| 1545 | IN DOOR Termination KIT for 33KV(E) XLPE Screened 3 core cable |
| 1546 | 25-50 mm2 |
| 1547 | 70-95 mm2 |
| 1548 | 120-185 mm2 |
| 1549 | 240-400 mm2 |
| 1550 | OUT DOOR Termination KIT for 33 KV(E) XLPE Screened 3 core cable |
| 1551 | 25-50 mm2 |
| 1552 | 70-95 mm2 |
| 1553 | 120-185 mm2 |
| 1554 | 240-400 mm2 |
| 1555 | Straight through Joint for 33 KV(E) XLPE Screened 3 core cable |
| 1556 | 35-70 mm2 |
| 1557 | 95-150 mm2 |
| 1558 | 185-300 mm2 |
| 1559 | 400 mm2 |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
