|
| 1 | Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates.Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading ofincorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender. |
| 2 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness ( below or above ground level). |
| 3 | Demolition of cement concrete (reinforced) of any description and in any position not other wise specifically provided for. |
| 4 | Dismantling of Asbestos cement (corrugated or semicorrugated etc) sheets in roof coverings |
| 5 | Dismantling plain or corrugated steel sheeting , any gauge, thickness including Nainital or similar pattern roof coverings. |
| 6 | Brickwork or stone/boulder masonry, build in lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles |
| 7 | Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing |
| 8 | Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and incl taking down carefully pointwiring for refixing. |
| 9 | Dismantling of timber scantlings 40 Sqcm and over in section in any position (unframed work) |
| 10 | All as per item no (8) but in fillets, rails, posts, rafters, purlines etc.under 40 Sqcm in section. (Unframed work) |
| 11 | Dismantling mild steel work of any description not otherwise provided for |
| 12 | Dismantling of boarding , any description , fixed in any position with nails. |
| 13 | Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads. |
| 14 | Taking down shutters of any description n exc 1 Sqm each. |
| 15 | Taking down shutters of any description exc 1 Sqm n exc 2 Sqm. |
| 16 | Taking down chowkhats with shuttersofany description n exc 1 .5 Sqm each . |
| 17 | Taking down chowkhats with shuttersofany descriptionexc 1 .5 Sqm but n exc 4 sqm each each . |
| 18 | Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store. |
| 19 | All as per item No (17)but 20mm bore. |
| 20 | Dismantling water tanks of capacity exc 500 & nexc 1000 litres and removing to store. |
| 21 | Dismantling water tanks of capacity exc 250 & n exc 500 litres and removing to store. |
| 22 | Dismantling of floor hearth or wall tiling, including cement bedding but not backing and rubbish off the premises. |
| 23 | M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4.Complete all as specified and as directed. |
| 24 | M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius in half brick thick wall built in CM 1:4.Complete all as specified and as directed. |
| 25 | Taking down cement plaster of any description on brick or stone wall etc, including raking out joints, hacking for key, scrubbingdown with water etc. complete all as specified and directed. |
| 26 | M&L for rendering 15 mm thick, CM 1:4 on fair faces of brick work or concrete surfaces by making surfaces even and smooth (mixed with water proofing compound which shall be measured and paid for separately under respective item) without using extra cement complete all as specified and directed. |
| 27 | M&L for rendering 10 mm thick, CM 1:6 on other than fair faces of brick work or concrete surfaces by making surfaces even and smoothwithout using extra cement complete all as spfddirected. |
| 28 | M&L GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding , joists, etc. In walls, ceilings, stanchions, beams, etc. Including all laps , cutting and waste.complete all as specified and directed. |
| 29 | M&L for rendering 10 mm thickin CM 1:4, on one side of lathing and making surfacesevenand smoothwithout using extra cement. complete all as specified and directed. |
| 30 | M&L for rendering 15 mm thick, CM 1:4 on other side of lathing by making surfaces even and smooth (mixed with water proofing compound which shall be measured and paid for separately under respective item) without using extra cement complete all as specified and directed. |
| 31 | S&F for rolled mild steel in joist, channel, angle or tee / tubular sections , fixed independently with connected plates Fe 410-W (Gde- E-250) quality-B |
| 32 | M&L second class wrought hard wood in scantlings (Timber fixed). |
| 33 | M&L for 20mm thick secondclass hardwood planed at both sides boarding as in eaves boards. |
| 34 | M&L for 6mm thick asbestos cement corrugated or semi-corrugated sheets in roofs, walls ,sunshed etc fixed with L-Type or J-Type or cranked hook bolts.. |
| 35 | S&F for 0.63mm thickness of Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screw and washers, in roofs, walls etc with grade of zinc coating 275fixed with L-type or J-type or cranked hook bolts in lieu of screws |
| 36 | S&F for 0.63mm thickness Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 |
| 37 | Except sheeting (any thickness) old dismantling galvanised, corrugated MS sheeting with two corrugations side lap, fixed with L or J type or cranked hookbolt |
| 38 | M&L for pre painting galvatume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of an colourhaving tensile strength of 550Mpa as in roof covering/cladding incl ridge hip etc fixed with tapping screws & L type or J type hooks etc complete |
| 39 | M&L for pre painting galvatume aluminium zink coating GI based plain steel sheet 0.50mm thick of an colourhaving tensile strength of 550Mpa as in roof covering/cladding incl ridge hip etc fixed with tapping screws & L type or J type hooks etc complete |
| 40 | M&L 4mm thick asbestos cement plain building boards, fixed to timber framework in ceiling with screws, and including refixing of old point wiring and fittings and replaceing old damaged fittings. |
| 41 | M & L including preparing of new surfaces and treated with threecoats of white wash on new AC board ceiling surfaces. |
| 42 | S& F Anodised aluminium snap grid frame of size 605 x605 work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roofby means of ceilling cleats/ 2 mmdia wiremade out of G.I. flat 40 x 3 mm size 60mmcomplete all as specifiedall as specified and as directed |
| 43 | S&F for 12mm th perforated particle board/tiles for insulation and accoustic purposes 60x60cm in size suitably placed in false ceiling grid made of aluminium as specification |
| 44 | M&L for 50mm thick planed at both sides boarding as in rafters,truess and members complete all as specified and directed |
| 45 | M&L for 50mm thick clean sawnas in joist of ceiling complete all as specified and directed |
| 46 | M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc13 sq.cm & n exc 25 sq.cm)as in studs of ceiling/sunshed . |
| 47 | M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc 3 sq.cm & n exc 6 sq.cm)as in fillet. |
| 48 | M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc 6 sq.cm & n exc 13 sq.cm) asin ceiling/window /sunshed |
| 49 | M&L for 75mm thick cement concrete type C-2,1:3:6(40mm graded aggregate) as in plinth protection ,footpath and making finished even and smooth without using extra cement. |
| 50 | M&L for 40 mm thick cement concrete type B-1,1:2:4(20mm graded aggregate) as in floor th and making finished even and smooth with using extra cement. |
| 51 | M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wallfinishes in CM 1:6 |
| 52 | M&L for rendering 10 mm thick roughplastering on verticalfair faces of brickwork surfaces in CM1:4 |
| 53 | M&L for non skid coloured tiles 7mm thick area of each tile exc 0.11 Sqm but n exc 0.18 sqm , in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 54 | M&L for non skid coloured tiles 7mm thick area of each tile exc 0.06 Sqm but n exc 0.11 sqm , in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 55 | M&L for Vitrified ceramic tiles 10mm polished area of each tiles n exc 0.36 Sqm in floors and as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match. |
| 56 | M &L for glazed coloured tiles in vertical surfaces. but 300mm x 200mm x 7mm thickset and jointed in cement slurry and pointed in colour to match |
| 57 | S & F 300 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I |
| 58 | S & F 500 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I |
| 59 | S & F 1000 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I |
| 60 | S & F in repair 20mm dia of bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed |
| 61 | S&F for second class hardwood plain,solid,straight,chowkats and frames,wrought,framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints. |
| 62 | S & F 35mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels),with panels of timber flat on both sides(feather edged),or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkats. |
| 63 | S & F Flush shutters 30 mm thick, solid core construction, with block board core and plywood dace panels, commercial type on both sides incl provision of suitable blocks for taking mortice locks, latches or other fittings |
| 64 | S & F 2nd class hard wood glazed and skeletonshutters 35mm thick open rebated and prepared to received glass, without (sash bars), edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters asspecified in SSR Part-I, Section 1 Clause 8.20 (a). |
| 65 | S&F 30mm thick glazed and skeleton shutters 2nd class soft wood , open rebated and prepared to receive glass, gauge etc divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars provided with stiles and rails as specified in SSR Part I ,section 8 clause8.20(b). |
| 66 | S&FSolid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing. |
| 67 | M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plaincolour PVC© channel PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock and bottom rail on either side as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded. Sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing. |
| 68 | S&F solid PVC wall Lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specified |
| 69 | S&f 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame asper specified |
| 70 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; largehasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and as directed. |
| 71 | S & F 100mm medium weight ,cold rolled mild steelbutt hinges. |
| 72 | S & F 75mm medium weight ,cold rolled mild steelbutt hinges. |
| 73 | S & F 150mm long anodised aluminium barrel tower bolts of extruded section and fixed |
| 74 | S & F 100mm long anodised aluminium barrel tower bolts of extruded section and fixed |
| 75 | S&F 300mm long anodised aluminium alooy sliding door bolts with hasp, stable (bolt type) and fixeing clips of sheet. |
| 76 | S & F 150mm anodised aluminum handles, cast type |
| 77 | S & F 100mm anodised aluminum handles, cast type |
| 78 | S & F Galvanized wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples . |
| 79 | M & L for 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50.m in each pane. |
| 80 | S & F 15mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors. |
| 81 | All as per item No (79) but 20mm bore. |
| 82 | S & F in repairs 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwedfor iron pipe or for brass ferrule. |
| 83 | S&F in repair 15mm chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch orbutterfly handle,screwed both ends for iron pipe or for unions and fixed |
| 84 | S&F in repair 20mm gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed |
| 85 | S & Fin repair 600 x 450mm bevelled edge mirror of selected quality glass,mounted on 6mm thick AC buliding board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 86 | M & L including preparing surfaces of new wood and wood based materials, of any description , not otherwise described, over 10 cm width or girth, and treated with two coats of synthetic enamel paint over coat of pink primer. |
| 87 | M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified |
| 88 | M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed. |
| 89 | M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed. |
| 90 | M&L including complete removal of existing treatment, preparation ofold Plastered surfaces of wall and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed. |
| 91 | M&L including complete removal of existing treatment, preparation ofold Plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed. |
| 92 | M&L for preparing old surfaces of ceilings and applying three coats of white wash. |
| 93 | M&L for M.S. TMT bars 8 to 10 mm dia bent to shape required including cranking bending and binding with M.S wire not less than o.9mm dia complete all as specified and directed. |
| 94 | Use and waste rough finished Form work to soffits of suspended slabs flat or batter such as roof slabs, floor slabs and similar work not exceeding 200 mm thick. |
| 95 | Rough finished flat Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC |
| 96 | M&L for R.C.C 1:2:4 type B1 nominal mix (using 20mm graded agg) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabscomplete all as specified and directed. |
| 97 | Supply and fixed in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) butincluding providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. |
| 98 | S&F in repair PVCsyphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets |
| 99 | S&F in repair Vitreous China wash basin, white, flat back, size 450 x 300 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and cutting for pinning in ends of brackets or erecting stand |
| 100 | S&F in repair ofPVC connections 15 mm size with PTMT nuts of length 450 mm long |
| 101 | S&F waste coupling of PTMT (half or full threaded) 32 mm dia (Min weight 45 gms |
| 102 | S&F in repair of 15 mm bore Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 103 | S&F in repair 25 mm low density polyethylene (LDPE) pipe of pressure rating 6 kgf/sq.cm |
| 104 | S & F brass chromium plated toilet paper holder complete all as directed by EIC |
| 105 | S & F in repairs vitreous China squatting pan ‘Orissa’ pattern size 580 x 440mm white , with integral foot rests including provision of lime concrete bedding ( excluding flushing cistern and flush pipe). |
| 106 | S&F in repair chromium plated shower roses with or without swiwel joints any size including fixing to steel pipe or union |
| 107 | S & F brass chromium plated tubular towel rail 20mmdia |
| 108 | S & F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 109 | S & F PVC (SWR) bends of radius 75mm bore. |
| 110 | S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore. |
| 111 | S & F PVC (SWR) vent cowl 75mm bore. |
| 112 | M&Lintegral waterproofingcompound |
| 113 | S&F in repair wash down water closet (pedestal pan) including connection to drain pipes and to flushing pipes antisy phonage pipe etc excluding flushing cistern incl flush pipe complete as as specified and directed |
| 114 | M & L plain cement concrete type D2 1:4:8 in foundations, filing & mass concrete. |
| 115 | M&L for sand filling under floor or below paver blocks incl. watering and consolidation. |
| 116 | M&Lfor coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment as directed. |
| 117 | M & L for plain cement concrete type-C2 1:3:6 (40mm garaded agg.) in surface channel and drains |
| 118 | S&F Stainless steel sink, 1.00 mm thick for kitchen with plus, waste pipe, washers, including cantilever cast iron brackets, connecting union etc, overall size 495mm x 420mm with bowl size 410mmx330mm x 160mm |
| 119 | M&L for granite slab green/black colour as in cooking platform/pillar etc 18 to 20 mm thick over cement screed bed with pre grinding and polishing/granite polishing and chamfering the corners to the entire satisfaction. |
| 120 | S & F 300mm MS ordinary rat tail rod pattern springs, incl roller plate complete |
