|
| 1 | Digging earth in any soil including mixed soil but excluding moorum, laterite sand stone or any other hard stone including spreading or stacking the spoils within a lead of 75 metres as directed bailing out water upto 1 metre depth, shoring etc.,when and if required and back filling with fine sand (including cost of sand) on completion of steining works.A) R.C.C. Ring Welliii) 1.8 metre diameter of digging for 1.5 metre internal diameter of well ring. |
| 2 | a) Upto 3 metre below G.L. |
| 3 | b) Beyond 3 metre upto 6 metre below G.L. |
| 4 | c) Beyond 6 metre upto 9 metre below G.L. |
| 5 | d) Beyond 9 metre upto 12 metre below G.L. |
| 6 | Extra rock cutting over the corresponding rate for digging for the respective internal diameter of the well will be allowed on the different stage of depth.ii) 100 % extra in Laterite rock or sand stone cutting with chisel and jumpers, but not requiring blasting. |
| 7 | a) Upto 3 metre below G.L. |
| 8 | b) Beyond 3 metre upto 6 metre below G.L. |
| 9 | c) Beyond 6 metre upto 9 metre below G.L. |
| 10 | d) Beyond 9 metre upto 12 metre below G.L. |
| 11 | R.C.C. well ring made with cement concrete 1:1.5:3 with stone chips and 0.80% reinforcement (including the cost of shuttering and reinforcement) cast at site fitted and fixed in position after proper curing true to plumb in the well including jointing with cement mortar 1:2 complete as per direction.c) 75 mm thick and 1.5 metre internal dia.Cement for joint filling-8Kg/m |
| 12 | Washing and development by pumping with 30 cum per hour capacity pump for a period till sand free water comes out and the discharge is about 30 cum per hour, followed by final yield test; inclusive of all tools, plants and scaffolding and hire charge of submersible pump, generator etc. all complete |
| 13 | Polyester reinforced PVC lay flat Hose Pipes 100 mm OD |
| 14 | Supplying, fittings & fixingof HDPE Pipes Grade -PE 80 (PN- 6.0)O.D.OFPIPES 90mmGRADE - PE80 (PN-6.0) |
| 15 | Solar Module: Supply, transport, installation and commissioning of lSI marked as per IS 14286 and IEC 61853(1). 61730(1&2), 61710 certified Solar Module of Multi crysta lin elM anocrvs tilIIine/ Monocrystalline PERC/bifacial cell with min. efficiency of 15% and fill factor more than 70%, laminated between sheet of -Ethylene Vinyl Acetate (EVA) and high transmissivity .3.2/4: mm tempered glass, framed in anodized aluminium frame .The power output of individual PV modules used in the PV array, under STC, should be a minimum of 300 Watt peak, with adequate provision for measurement tolerances.Modules supplied with the SPV system should have warranty for output wattage, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. Necessary test certificate also to be supplied. (As per direction of EIC)b)For 3 HP Off-grid Solar Water Pumping System with Monocrystalline/ Monocrystalline PERC/bifacial SPV modules - 3200-3300 Wp. |
| 16 | Module Mounting Structure ( For 2HP, 3HP and 5HP Solar Water Pumping System): Supply, transportation & installation of G.I manual tracking structure made of MS hollow section. pipes. plates, angles etc as per IS 1161/1239, 1079/2062, to hold min 300 wpSPV Module as per or awingand specification of MNRE. The steel structure is to be protected with minimum 80 microngalvanisation(hot dip) and provided with dual axis manual tracking arrangement three times in a day and seasonal tilting are to be regulated to face the sun optimally.(As per direction of EIC) |
| 17 | a) The weight of the Module Mounting Structure holding 4 Modules should not be less than 165 Kg |
| 18 | b) The weight of the Module Mounting Structure holding 6 Modules should not be less than 235 Kg |
| 19 | Foundation of Module Mountingstructure: Suitable and stable Reinforced Cement Concrete for dual axis manual tracking SPV Module structure as per approved drawing. |
| 20 | a) For 4 module structure. |
| 21 | b)For 6 module structure. |
| 22 | Power conditioning unit with IP54 enclosure:Supply, transport, installation and commissioning of IP 54 protected enclosured Inverter Unit qualifying IEC 61683-Efficiency measurement and IEC 60068-2-Environment Standard safety standard suitable for 3 Phase A.C. motor, IGBT based high voltage switching inverter with MPPT technology, to take care of the variation of Sun light and will be suitably mounted inside the metal enclosure. Inverter should have protection against Dry run, Over current, Under current, Over voltage, Under voltage, Short circuit etc. System should be able to run at low sunshine and minimum 7 to 8 hours a day run should be possible during normal sunshine. condition. Inverter should have option to auto start for any short trip off due to low light/ cloudy situation except for dry run. Inverter should be provided with a display to show the various parameter by the user such as Voltage, Current, Solar panel DC voltage, Inverter IGBT temperature, Out put AC voltage, Output frequency, Pump flow (direct or calculated method), Irradiation etc. The system should store the data at a set interval, be capable to transfer it to external storage device and support communication of its operational parameters and logs over Modbus protocol It should also monitor and save total run time, total water pumped etc. There should be provision for interfacing GPRSbased data transmission.b) For 3 HP capacity Pump-motor set |
| 23 | Cable and Accessories: Supplying, fitting and fixings of UV rated Copper Cable laid inside HOPEconduit and other accessories as per followings with necessary connection with the Solar PV Module, MPPT etc.i. 4.0 Sq mm single core multi studs - 10 Mtrs (Minimum)ii. 6.0 Sq mm single core multi struds -5 Mtrs (Minimum)iii. Lugs, HOPEPipe, Flexible Pipe, Saddle, Cable, tie etc |
| 24 | Earthing: Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip)wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. 5 & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partlyabove ground level driven to an average depth of 3.65 Mts. below the ground level as below:By lSI-Medium GI pipe including excavation of soil for installation of Earth Electrode and filling & ramming and connecting to individual structure to earth electrode including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. (As per direction of EIC) |
| 25 | Lighting system at scheme (with lighting pole) Dusk to dawn lighting arrangement of at 4m hight above ground level, with hot dip galvanaised 80mm X 50mm, midium duty pipe, with 12volt, 15Ah 2in 1 lithium ion/ferro phosphate battary with inbuilt 7-11 watt LED lamp, 50wp solar panel to cover the scheme area. The lighting system should be warranted for 5 years from the date of instalation. |
| 26 | Lightning protection(pole mounted)(: Lightning protection with 3\" X 1.5\" G.I pipe of 4 mts height with base flange inproper RCCfoundation and S & F Lightning Conductor Air Terminal made of 20 mm dia 1000 mm long GI pipe (ISI Medium) having five discharge prongs of 4 SWG GI (Hot Dip) wire at top duly soldered with 7/16 stranded GI (Hot Dip) wire and 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etcEarthing with 65 mm dia GI pipe (Medium)x 3.0 Mts. long and 1 x 19/10 stranded GI (Hot Dip) wire (4 Mts. long), 20 mm dia x 125 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts.(provision of one lightning protection for each structure) |
| 27 | Supply and instalation of 3phase electro motor pump motor set sutable for solar opperation covering 5 years warrenty for the following conditions including loading unloading transportation etcC) 3hp ISI marked 3 phasepump-motor set having discharge at required head as bellow:iii) open wellsubmersible pump set marked as per IS:14220 for PDW with discharge of 6.5 lps-7.14 lps at 18mtr total head with foot valve, required quantity of flexible delivery pipe (15m), clamps, bend, footvalve and all other accessories to complete connection of suction and delivery side(conforming latest ISI amendment) |
| 28 | Remote monitoring for 5 years: Supply & installation of GSM/GPRSbased Data Transmitter or Modem and to provide remote monitoring serviceto transmit the parameters to central serverfrom the Solar pumping System with time stamp at user-defined interval and report generation at the buyer end, |
| 29 | Testing and commissioning of scheme after completion of all work |
| 30 | Comprehensive maintenance charges for 4 years beyond 1 year warranty period (which cover monthly inspection, Yearly training to WUA, to attend breakdown within 3 days and to keep the scheme in operation without lapse of time)c)For 5 HP both for Submersible & Surface pumpNote:lTotal comprehensive maintenance charge is to be withheld in addition to Securirty Deposit. Security Deposit will be released after expiry of warranty period of 1 year & Comprehensive maintenance charges will be released @ i) Rs1.00for 2 HP,ii) Rs.1.00for 3 HP,iii) Rs.O.7Sfor 5 HP Submersible & Surfaceper Wp per year at the end of each maintenance period l.e.at the end of 2nd year, 3rd year, 4th year, 5th year. In case the \"Bidder\" does not provide service during the warranty & comprehensive maintenance period, the amount so held up will be forfeited(As per direction of EIC) |
| 31 | SupplyingfittingfixingfabricatedMSKioxBoxboth side openable ofsize 1000 mmx600mmx650 mm mounted by 4 numbers legs & frame made of MS angle 65x65x6 mm & 50x50x5 mm. Allsides are covered with 3mm MS Sheet on the frame of MS angle 25x25x3 mm with back side cover made of 1.5mm thick MS sheet & providing MS channel door made of 25x25x3 mm MS channel inside the box for fitting the electrical equipments having locking arrangement with pad lock,two number MS hasp bolt of 16mm dia x300 mm long and two numbers of MS door handle.The legs are detachable type fitted with MS bolts &nuts bifurcated with 16mm dia drilled holes for mounting the same with nuts& bolts in the concrete base/pillar and painting two coats with antcorrosive red led painting completeIncluding cost of concrete. As per drawing and direction of EIC during the work. |
| 32 | Supplying fitting fixing of quick connect pipe (metal latch type) as per IS-14151HDPE Pipes with Quick Release Coupler(Pipe of Class I; 2.5 kg / cm 2 IS:14151 Part I, 75 mm diameter & 6m long |
| 33 | QRC HDPE 75mm Service Saddle IS: 14151 Part II |
| 34 | GI Riser Pipe 3/4 inch diameter x 100 cm long |
| 35 | Metal Impact sprinkler as per IS 12232: Sprinkler Nozzles (1.7 to 2.8 kg / cm 2 ), 12 to 18m radious throw, 2050 LPH discharge IS12232 Part I |
| 36 | QRC HDPE Bend with Coupler 90 deg (75 mm) IS:14151 Part II |
| 37 | QRC HDPE Pump Connecting Nipple, 75 mm IS:14151 Part II |
| 38 | QRC HDPE End Plug (75mm) IS: 14151 Part II |
| 39 | QRC HDPE Tee with Coupler (75 mm) IS:14151 Part II |
| 40 | Supplying , fitting and fixing of PVC Control Valve of approved make and quality all complete as per direction of Engineer-in-Charge. |
| 41 | Flex with printed details of WUA as provided during work of size 900mm X 600 mm |
| 42 | 2 in 1 Hand Cum Battery Operated Sprayer BS-21 (12V/8AH) with one year warrenty |
| 43 | Distribution Tank of size L 1.5m X B 1.5m X H 1.1m with plaster and net cement punning as per direction of EIC and Drawing |
| 44 | Supplying, fitting and fixing including transportation of sign board for identifying the exact location of PDW Scheme (one at road side and other at site) theboard will be made 3 mm thick MS plate of size 300 mm x 600 mm and fitted and fixed on 50 mm GI Pipe of IS 1239/90 (part-1) including cutting, welding and writting of both sides of Sign board. Base - Yellow, and words - Red. Both bottom end of the stands pipe will be grouted in 1:2:4 CC on a single brick flat soling. This will include one materials and labour complete as per drawing and direction of E.I.C. |
| 45 | Earthing: Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip)wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. 5 & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:By lSI-Medium GI pipe including excavation of soil for installation of Earth Electrode and filling & ramming and connecting to individual structure to earth electrode including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. |
| 46 | 25/40 mm dia PVC pipe both end screwed & one end socketted |
| 47 | 2.5 sqmm copper pvc insulated (heavy duty) flat weather proof electric cable duly ISI certification mark-3core |
| 48 | Painting block letters or digits in Black Japan or anyapproved paint as per direction.b) Size above 2.5 cm. and upto 4 cm. |
| 49 | Vermicompost pit of size L 5.3m X B 1.9m X H 0.92m with plaster and net cement punning as per annexture VII and As Per Drawing |
| 50 | INSURANCE @ 2% for item no 7,10,13 and 14 for a period of 5 years.(As per direction of EIC) |
