Construction C / O Veternary Dispensary Building At Shiva Khad Tehsil Thunag Distt. Mandi Hp C / O Building Portion Site Development Ws And Si And Rainwater Harvesting System
Tender Value
32.10 Lakhs
Estimated cost
Bid Submission
04 Apr 2022
0 days left
EMD
64300
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
janjehli → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction C / O Veternary Dispensary Building At Shiva Khad Tehsil Thunag Distt. Mandi Hp C / O Building Portion Site Development Ws And Si And Rainwater Harvesting System
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, .All kinds of soil asperthe directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . |
| 2 | Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any leadfrom the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth asperthe directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (one Cement : five fine sand) : ten graded stone aggregate 40 mm(fourty millimetre)nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (one Cement : five coarse sand) : ten graded stone aggregate 40 mm(fourty millimetre)nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40 mm(fourty millimetre)nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for Beams, cantilever, girders and lintelssides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in anydepth in all heightfrom floor. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platformincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm (twenty centimetre)wideincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 10 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (one cement : three coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one pont five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal sizeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 13 | Providing weepholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 14 | Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals. |
| 15 | Providing and laying damp-proof course 40mm (fourty millimetre) thick with cement concrete 1:2:4 (one cement : two coarse sand: four graded stone aggregate 12.5mm (twelve point five millimetre nominal size)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 16 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oilincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 17 | Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre)nominal size over 75mm(seventy five millimetre)thick bed of dry brick ballast 40 mm (fourty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 18 | Constructing Course rubble hammer dressed \"U\" shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre)in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement: three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm (fourty millimetre) nominal size) and 7.5 cm (seven point five centimetre)cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 19 | Steel reinforcement for R.C.C. work in Thermo-Mechanically Treated bars of grade Fe-500D or more including straightening, cutting, bending, placing in position and binding all complete above plinth level complete up to anylevelincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 20 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge . |
| 21 | Providing and laying Square rubble masonary coursed with hard stone of approved quality in Superstructure above plinth level in Cement Mortar 1:6 (one Cement: six Sand)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 22 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (one cement : four coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 23 | Brick work with common burnt clay F.P.S. (non modular) bricks of class esignation 7.5 (seven point five)in foundation and plinth in: Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 24 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundations and plinth in : Cement mortar 1:3 (one cement : three coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 25 | Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement :six sand : tweleve graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 26 | Coursed rubble masonry (second sort) with hard stone in foundation & plinth with : Cement mortar 1:6 (one cement : six coarsesand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 27 | Stone soling/boulder filling dry hand packed in under floor , Stone filling behind abutment wing wall and retainling wallincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 28 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately.First class deodar woodincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 29 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Second class Deodar woodincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 30 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (ziro point six three millimetre) , for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters Second class Deodar woodincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 31 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 32 | 300x16 mm (three hundred into sixteen millimetre) |
| 33 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. completeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 34 | 200x10 mm (two hundred into ten millimetre) |
| 35 | 150x10 mm (one hundred into ten millimetre) |
| 36 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. completeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 37 | 125mm (one hundred twenty five millimetre) |
| 38 | 100 mm (one hundred milimetre) |
| 39 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 40 | Providing and fixing bright finished brass hard drawn hooks and eyes 250 mm (two hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 41 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg ( thirty five kilogramme ) and door width upto 700 mm (seven hundred millimetre) , with necessary accessories and screws etc. completeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 42 | Providing and fixing 19 mm ( ninteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre)thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre)thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete as per detailed drawingincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 43 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all completeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 44 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, kg railings, brackets, gates and similar worksincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 45 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etcincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 46 | Providing and laying antiskid full body vitrified floor tiles (premium quality) matte finish in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% (ziro point ziro eight) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size 600x600 mm(six hundred into six hundred millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalentincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 47 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm(three hundred into three hundred into nine millimetre) having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm(twenty millimetre) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. completeincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 48 | Providing and laying antiskid full body vitrified floor tiles(premium quality) matte finish in different sizes(thickness to be specified by manufacturer), with waterabsorption less than 0.08 % and conforming to I.S.15622, of approved make, in all colours & shade, inskirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cementmortar 1:3 (one cement: three coarse sand), jointing with greycement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm (six hundred into six hundred millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalentincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 49 | Providing and laying Antiskid digital Ceramic glazed floor tiles of size 300x300 mm (three hundred into thre hundred millimetre)(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre)thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete of Johnson/ Kajaria/ AGT Tiles/ RAK/ Orient Bell or its equivalentincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 50 | Providing And fixing glazed Digital Ceramic tiles 300 x 450 x 8 mm (three hundred into four hundred fifty into eight millimetre) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (tweleve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurryincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 51 | Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm (fourty millimetre) thick with 20 mm (twenty milimetre) nominal size stone aggregate including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 52 | Providing and fixing 0.62mm (Zero point six two milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) miconsprimer coating to back coast of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with self drilling and self tapping fasten of size 5.5 mm (five point five millimetre) dia and 55 mm (fifty five millimetre) lapcomplete with all accesoriees including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 53 | Providing and fixing ridges or hips 62 cm (sixty two centimetre) overall with 0.62mm (ziro point six two millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20(twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories with all accesoriees including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 54 | Providing and fixing valley 90 cm(ninty centimetre) overall 0.62mm (ziro point ix two millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 55 | Providing and fixing M.S. BP Sheet 1.66mm (one point six six millimetre) to 2mm (two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 56 | Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (fourty five centimetre) overall semi- circular plain G.I. sheet gutter with iron brackets 40x3mm(fourty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. :0.80 mm (ziro point eight ziro millimetre) thick with zinc coating not less than 275 gm/m2 including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 57 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 58 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millinetre) gap for thermal expansion, (i) Single socketed pipes. : 110 mm (one hundred ten millimetre) diameter |
| 59 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 60 | Coupler :110 mm (one hundred ten millimetre) |
| 61 | Bend 87.5°(eighty seven point five)110 mm (one hundred ten millimetre) bend |
| 62 | 110 mm (one hundred ten millimetre) Shoe |
| 63 | Providing and fixing unplasticised -PVC pipe clips of design to unplasticised - PVC rain water pipes by means of 50x50x50 mm(fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( one cement: four coarse sand) and making good the wall etc. complete. 110mm (one hundred ten millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 64 | Providing and laying 15 mm (fifty millimetre)cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: sixcoarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 65 | Providing and laying 6 mm (six millimetre) cement plaster 1:3 (one cement : three fine sand) finished with a floating coat of neat cement and thickcoat of Lime wash on top of walls when dry for bearingof R.C.C. slabs and beamsincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 66 | Providing and laying Pointing on stone work with cement mortar 1:3 (one cement : three fine sand) Flush/ Ruled pointing including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 67 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat withcement primerincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 68 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 69 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 70 | Providing and applying white cement based putty of average thickness 1 mm (one millimetre) , of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 71 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm (six hundred into four hundred fifty millimetre) internal dimensions including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 72 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 73 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 74 | 15 mm (Fifteen millimetre) nominal bore |
| 75 | 20 mm(twenty millimetre) nominal bore |
| 76 | 32mm (Thirty millimetre) nominal bore |
| 77 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :. 25 to 40 mm (twenty five into forty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 78 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 79 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 20 mm(twenty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 80 | Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre (one meter) spacing. This includes the costs of cutting chases and including testing of joints complete Concealed work , including cutting chases and making good the wall etc . including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 81 | 1620 (20 mm OD) (twenty millimetre) pipe |
| 82 | 1216 (16 mm OD)(sixteen millimetre) pipe |
| 83 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (hundred millimetre)sand cast Iron P or S trap, 10 (ten) litrelow level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimetre) with integral type foot rests including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 84 | Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimetre)with a pair of 15 mm C.P. brass pillar taps including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 85 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm (forty milimetre) dia including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 86 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work 40mm dia) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 87 | Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 88 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm (fifteen millimetre) nominal bore.including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 89 | Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimetre), breadth 102mm (one hundred two millimetre), height of 75mm (seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 90 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 91 | 15mm (fifteen millimetre) |
| 92 | 20mm (twenty millimetre) |
| 93 | Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 94 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 95 | Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm (one hundred ten into ninty millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 96 | Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 97 | 110mm (one hundred ten millimetre) dia |
| 98 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 99 | 110mm(one hundred ten millimetre) dia |
| 100 | Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 101 | 110mm (one hundred ten millimetre) dia |
AI Tender Summary
Tender Timeline
Mar 28, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedApr 04, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 04, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender