Construction Of Water Supply Scheme At Kitadi Makta G.P Tah- Chimur
Tender Value
21.28 Lakhs
Estimated cost
Bid Submission
01 Apr 2022
0 days left
EMD
22000
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
chimur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Water Supply Scheme At Kitadi Makta G.P Tah- Chimur
BOQ
| Sl. No. | Item Description |
| 1 | SubWork 1 BoreWell 150 mm dia60 M deep Item No. 1 Drilling of Tube well in all types of strata 300 in all types of strataincluding all charges ---------- etc. complete. |
| 2 | Item No. 2 Providing and fixing150 mm dia M.S. casing pipe class B 4.85 mm as per IS 1239 (Blank) |
| 3 | Item No. 3 Providing and fixing 150 mm dia M.S. casing pipe class B 4.85 mm as per IS 1239 (Slotted) |
| 4 | Item No. 4 Providing and fixing 150 mm dia M.S. CAP |
| 5 | Item No. 5 Providing and fixing wooden block for support to clamp of bore well |
| 6 | Item No. 6 Providing and fixing M.S. clamp for support to clamp of Tube well |
| 7 | Item No. 7 Providing gravel for packing including transportation upto site of work of good quality. |
| 8 | Item No.8 Yeild test |
| 9 | Item No.9 Source investigation / certificate charges |
| 10 | Item No.10 Trandportation of drilling rig and unit upto site of work ---------- etc. complete. |
| 11 | Item No.11 Devlopment of tube well by air compressor unit. |
| 12 | Item No. 12 Providing and fixing M.S. bell cap for Tube well |
| 13 | SubWork 2 :- Deepining of Ex Supply Well 5.0 m diaItem No.1Desilting the Supply Well, Intake Well / Head Works, Sump of water supply / sewerage works etc. in wet or dry condition including lifts upto 9 M and lead upto 150 M as required beyond the work site, stacking, spreading, including necessary guarding, etc. complete, as directed by Engineer-in-charge. Ex Well 9 M depth + 3 M Staging Wall LIFT 12 to 13.5 M |
| 14 | Item No.2 :-Excavation for in general in Hard material comparising of soft rock, hard rock manjra rockin wet or dry condition for head works ie. Intake well connecting main jack well pump house supply well etc. for lift 1.50 M and lead of 150 M including barricating guarding disposing off surplus excavated stuff with radius of 0.50 km as directed by engineer in charge.Ex Well9 M depth +3.0 M Staging Wall LIFT12.0 to 13.5 M |
| 15 | LIFT 13.5 to 15 M |
| 16 | LIFT 15 to 16.5 M |
| 17 | LIFT 16.5 to 18M |
| 18 | Item No.3 :- Dewatering the excavated trenches and pools of water in the building trenches / pipeline trenches, well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-in-charge (including cost of machinery, labour, fuel), etc. complete. (Bd-A |
| 19 | Item No.4:- Providing and fixing mild steel grill work for windows/ventilators of 20 Kg./Sqm. as per drawings including necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting, etc. complete. |
| 20 | Item No.5:- Providing and fabricating structural steel work in single stanchions composed of R.S.J. channel, etc. with caps, bases, mild steel plastes angles, anchor bolts etc. as per detailed design and drawing or as directed including cutting, fabriction, hoisting,hoisting, errecting, fixing in position, making reveted/bolted/welded connection and one coat of anticorrosive paint, and over it two coats of oil painting etc. complete. 2 availablegirder is usedExtra Girder for full grill ISMB 250x 125 mm |
| 21 | SubWork 3:-Pumping MachinerforSUPPLYWell 2 Sets& 1 set for tube well Submersible Pumps 4 BHP Q7186 Item No.1 Providing erecting and giving test ofSubmersible Pumpsets conforming to is 8034 and motor conforming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene impeller. Motor suitable for working on 415 V + 10% .3 Ph., 50 Hz. A.C. supply Cable guard, thrust carbon/fibre beaning to accept entire hydraulic thrust, waterproof winding shall be Provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design antithrust stream lined non return valve shall be Provided with the pum. Suitable suction strainer shall also be provided. 3 core single / double run copper conductor submersuble type flat cable 3m and 2 pairs of erection clamps shall be provided along with the pump rates per pump upto 20 stages are as below.Submesible pump set 150 mm dia ( with Bronze? Stainless steel (CF8M) upto 8 stages 3 B.H.P.min head -37M M Q 7186 Lit/hr for Supply Well |
| 22 | 4 B.H.P.min head -82m Q 7186Lit/hr For BoreWell |
| 23 | Item No. 2 Supplying and erecting DOL starter to operate squirrel cage induction motor working on 380- 440 Volt, 3 phase, 50 Hz with no volt coil and over load element with necessary material and connected to supply, etc complete. Starter with original sheet steel encloser. I.G.-4 with contractor rating 16 amp. |
| 24 | Item No. 3 Supplying and erecting plain copper conductor PVC insulated flexible cable as per IS 694/1990 of following grade upto 1100 volts. CB 1-3 core - 4 sq mm PVC cable |
| 25 | Item No. 4 Providing and fixing of steel clamp fabricated from M.S. flat 65 mm x 6 mm 1 m length including nut bolts and washers. M.S. Clamp. |
| 26 | Item No. 5 Providing ISI mark G.I. pipe of following class and dia.excluding GST levied by GOI and GOM in all respect including inspection charges, transportation to stores, etc. completeas per IS-1239/2004. 50 mm dia. G.I. Heavy Class. For tube well |
| 27 | 50 mm dia. G.I. Heavy Class. For Supplywell |
| 28 | Item No. 6 Lowering, laying and jointing G. I. pipes and specials of following class and diameter including conveyance from stores to site of works, all labour, etc. complete either underground or in vertical position, as directed by Engineer-in-charge 50 mm dia. G.I. Heavy Class. For tube well |
| 29 | 50 mm dia. G.I. Heavy Class. For Supplywell |
| 30 | Item No. 7 Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984 Sluice valve 50 mm dia. |
| 31 | Non Return valve - 50 mm dia. |
| 32 | Item No. 8 Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) Sluice valve 50 mm dia. |
| 33 | Non Return valve - 50 mm dia. |
| 34 | Item No. 9 Providing & erecting 3 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB32 A/40-4Pole, 3 Phase. |
| 35 | Item No.10 Supplying and erecting cupboard for enclosing switchgears or for any other purpose made from selected marine plywood planks 19 mm thick duly varnished/ painted from inside and from outside with brass hinges and locking arrangement with suitable lock with keys in duplicate. Cupboard shall be duly grouted with suitable size of iron work in wall at the bottom. (Size of cupboard shall be specified in the estimate) |
| 36 | Item No.11 L.T. current transformer with wound/bar primary 10/5 Amp, ratio with 15 VA burden erected in provided M.S. box duly secured with inslulting materials and connected to the meter. L.T. Transformer |
| 37 | Item No. 12 Providing and erecting main switch or ISI mark - Amp. |
| 38 | Item No. 13 Providing and fixing frame work for pannel board near well with ISMC 100x50 and ISA 35x35x6 mm etc.complete. M.S.Frame pannel board |
| 39 | Item No. 14 Supplying and erecting PVC pipe \"B\" class 25 mm to 40 mm for eneclosing PVC cable.PVC cable. |
| 40 | Item No. 15 Supplying and erecting galvanised cast iron earth plate 60x60x0.6 cm buried in specifically prepared earth pit 1:5 m below ground level with 30 kg Charcoal and Salt in alternatre layers necessary length of double G.I. Earth wire 8 SWG connected to plate with cadmijm plate G.I. nut bolts 12 mm dia. with bituminous compound and run through 12 mm dia .G.I. pipe 3 m long remaining portion of G.I. wire from surface of earth to switch gear in PVC ippe upto accessible height duly sealed at both ends by bituminous compound complete connected to the nearest switch gear with end socket as per direction and duly tested by earth tester and recording the results.Earth Plate. For tube well |
| 41 | Item no 16:- Supplying and erecting \"B\" class G.I. Bend in position with necessary material. PW1-5 50 mm dia G.I. Bend |
| 42 | PW 2-5 G.I. Tee 50 mm dia. |
| 43 | Item No. 17:- Making trenches of suitable width and 0.7 m deep and laying provided L.T. cable and refilling the same with screened sand bed of 0.2 m thick to embedded the cable and bricks placed on both sides length wise and top width wise all over the run and refilling the excavated earth without shone or hard material and making the surface proper with 0.15 m crown on the top.pressure gauge 100 mm dia. |
| 44 | Item No. 18:- Providing and errecting voltmeter A.C. 50 Cycles / Sec. With 0 to 500 v. range flush type errected on provided M.S. 60 and errected withnecesssary PVC wireVoltmeter 144 x 144 Sq. mm. |
| 45 | Item No. 19:- Providing and errecting ammeter A.C. 50 0/5 450 v. or suitable range flush type complete errected in provided M.S. box connected to supply . Ammeter 96 x 96 Sqmm. |
| 46 | Item no 20:- Supplying and errecting set of 3 pilot lamp all back light with colour glasses with monitor lamp 230 volt / 250 volt errected on provided M.S. box with pannel type fuses and connected with PVC wire. |
| 47 | Item No. 21 Supplying and errecting triple pole Iron clad/metal clad switch and fuse 415/500 v. of suitable rating as below or approved make errected on original frame. I)Incoming ICTPN-32 Amp/ |
| 48 | ii)out going ICTP-16 Amp. |
| 49 | iii)For lighting ICDP-16 Amp. |
| 50 | Item No. 22 Providing and fixing M.S.E.B.kitkat set etc. complete |
| 51 | Item No. 23 Operation of pumping machinary through mobile network system |
| 52 | SubWork 4 :-Distribution System110 to 75PVC4 Kg/Cm2 L =1245M Item No. 1. Excavation for foundation / pipe trenches in hard rock and concrete road by chiselling, wedging, line drilling, by mechanical means or by all means other than blasting including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the area and lifts as below, stacking as directed by Engineer-in-charge, normal dewatering, excluding backfilling, etc. complete by all means.Cement Road |
| 53 | Item No. 2. Excavation for foundation / pipe trenches in earth soils of all types, Sand,gravel and soft murumincluding removing the excavated material upto a distace of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. |
| 54 | Item No. 3. Excavation for foundation / pipe trenches in hard murum and boulders ,WBM road including removing the excavated material upto a distace of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. |
| 55 | Item No. 4. Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 including all local and central taxes, transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores / site and stacking the same in closed shed duly protected from sun rays and rains including cost of jointing material i.e. solvent cement, etc. complete (selffit type to be jointed with cement solvent).110mmPVC 4 kg/sqcm |
| 56 | 75mmPVC 4 kg/sqcm |
| 57 | Item No. 5 Providing PVCspecails complete 10% of cost pipe |
| 58 | Item No. 6. Lowering, laying and jointing with P.V.C. pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material, except cement solvent, rubber ring, giving satisfactory hydraulic testing as per IS code, etc. complete (with cement solvent joint / ring fit joint). 110mmPVC 4 kg/sqcm |
| 59 | 75mmPVC 4 kg/sqcm |
| 60 | Item No. 7. Hydrulic testing of PVC pipe line to specified pressure including cost of all materials and laboue and water for testing for specified length including cuttig, placing end cap making arrangment for filling safe water using resiprocating types pump which should be able to provide specified test pressure gauges and other necessary equipments,labour, operation charges, etc. required for testing. the rate under this item shall also include cost of retesting, if necessary and reinstating to original position. 110mmPVC 4 kg/sqcm |
| 61 | 75mmPVC 4 kg/sqcm |
| 62 | 80 mm dia PN 1. |
| 63 | Item No. 9. Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) 110mmPVC 4 kg/sqcm |
| 64 | 80 mm dia PN 1. |
| 65 | Item No.10. Providing ISI mark GI. pipe of following class and dia.including all statutory duties & taxes such as GST levied by GOI & GOM in all respect,inspection charges, transportation to stores, etc. complete as per IS-1239/2004.One coupler shall be provided with each full length of pipe cost of which is included in rates below. 150 mm GI Pipe Medium |
| 66 | Item No.11. Lowering, laying and jointing G. I. pipes and specials of following class and diameter including conveyance from stores to site of works, all labour etc. complete either underground or in vertical position, as directed by Engineer-in-charge.One coupler shall be provided with each full length of pipe cost of which is included in rates below. 150 mm GI Pipe Medium For Incasing on Nallah and road |
| 67 | Item No.12. Providing and fixing C.I. road box including loading, unloading and carting to site of work including all necessary excavation in all types of strata and fixing in murum packing, etc. complete. 100 mm x 225 mm (20 kg) |
| 68 | Item No. 13. Filling in plinth and floors / trencheswith approved excavated materials from foundation in 15 cm to 20 cm layers including watering and compaction complete. |
| 69 | Item No. 14 Providing and laying in situ following grades of C.C. of trap/granite/ quartzite/ gneiss metal for foundation and bedding including dewatering, form work, compacting and curing, finishing, etc. complete. In PCC M-150 |
| 70 | Item No. 15. Provding and constructing RCC CATTEL TROUGH as per drawing and design as per directed by engineer |
| 71 | SubWork 5:-Item No 1:-Commisioning running and maintaining the scheme to quantites, rated capacity, including manning necessary personnel such as operator, valveman, etc. as per requirements of the scheme and who should also administer chemical dose for a period of 1 month for individual scheme and 3 months for regional scheme, together with training of personnel spared by MJP/ Local Body and handing over the scheme to Local Body after completion of the above period as directed by Engineer-in-charge. Note: Required chemicals to be supplied by Department free of cost and electricity bill will also be paid by the Depertment. For single village without WTP one Months |
| 72 | SubWork 6 PROVISION FOR FHTC TAP CONNECTION Item No.:- 1 Providing and making UPVC/MDPE pipe consumer service connection on Distribution main by drilling hole with suitable means , including all labour , UPVC/MDPE Pipe of required length with or without Road crossing as described below, including cost of specials like Saddle/Clamp Saddle of suitable material, and diameter suitable for Distribution main, 15mm /20mm/ 25mm respective Dia Heavy duty Brass/Polyprophylyne(Twin Jacketed ) Ferrule , Male and Female thread adapter Elbow, Bends,couplers ,Tees, Clamps of suitable material and sundry materials as per requirment, including providing and fixing medium duty 15.mm brass bib tap, GI casing pipe of suitable diameter of 32mm/ 40mm/ 50mm respectively of required length for Road crossing, including requird labour for excavation in all types of strata up to the depth of 0.75m or as per site requirement,all types of plumbing fittings, refilling , Closing the water supply in that area, dewatering, hydraulic testing and restarting the water supply ,transportation of material etc. complete as directed by Engineer in A) Household Connection without water meter (Comression Saddle+ISI Mark Ferrul) for HDPE & PVC pipe For MDPE/UPVC Pipe Service Connection on Disribution mai A) With Road Crossing |
| 73 | B) WithoutRoad Crossing |
AI Tender Summary
Tender Timeline
Mar 25, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedApr 01, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 04, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender