Supplying Of Office Furniture Like Modular Workstation, Chair, Table, Sofa For Office Use Of Administrative Building-Ii Barasat, , barasat-West Bengal

Supplying Of Office Furniture Like Modular Workstation, Chair, Table, Sofa For Office Use Of Administrative Building-Ii Barasat, North 24 Parganas.-Executive Table ( Type-I , Very High Back Revolving Chair , Visitor Mid Back Revolving Chair , Sofa Set ( Three+One+One, Steel Storage With Glass Door Unit , Executive Table ( Type-Ii , Visitor Chair , Three Seater Sofa ( Type-I, One Seater Sofa ( Type-I ) , Centre Table ( Type-I , Glass Shutter Display Unit , Three Seater Sofa ( Type-Ii , One Seater Sofa ( Type-Ii ) : , Centre Table ( Type-Ii , Corner Table , Thirty Seven Seater Conference Table , Twenty Two Seater Conference Table , .High Backrevolving Chair , Mid Back Revolving Chair , Executive Table ( Type-Iii , Executive High Back Revolving Chair , Mid Back Four Legged Visitor Chair , Glass Door Display Storage , Reception Table , Modular Workstation , Workstation Mid Back Revolving Chair , Glass Door Storage, Three Seater Visitor Seating Chair , One Seater Visitor Seating Chair , Auditorium Chair , Mid Back Stage Chair,

Refer document

INR 400000.0 /-

Refer document

Name of Work:Supplying of office furniture like modular workstation, chair, table, sofa for office use of Administrative Building-II Barasat, North 24 Parganas.

Sl. No.	Item Description
1	Executive table (Type-I): Supplying, fitting & fixing ofVeneer/Membrane TopExecutive Work table of size about 2400W X 900D X 750H as per given specification and direction of Engineer-in-charge.-it is 50mm thickbatten structure which is made up 25mm thick veneer topbatten confirming to IS 12823: 1990 and 12 +12 mm thick MDF board batten confirmingof grade SBG II of IS 12406/Latest. 0.3 mm Veneer sheet is past on both the side of the structure with 0.3 mm thick veneer lipping glued with Kliberit-779.6 glue.Total thick ness of the TOP isWork top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section.Understructure- Gable end is Made up of it is batten structure is which is made up 25mm thick prelam particle board batten confirming to IS 12823: 1990 and 12+12 mm thick MDF board batten confirming of grade SBG II of IS 12406/Latest. 0.3 mm Veneer sheet is past on both the side of the structure with 0.3 mm thick veneer lipping glued with Kliberit-779.6 glue. Modesty is made up of 17 mm thick plane MDF board and 0.3 mm veneer sheet is paste on both the side. Modesty is having 600mm fixed height. The construction shall be aesthetically appealing completely knock down construction. All the panels are connected with each other by using fittings such as Minifix & Dowels. Cube main table with LH pedestal- it is batten structure is which is made up 25mm thick prelam particle board batten confirming to IS 12823: 1990 and 12 +12 mm thick MDF board batten confirming of grade SBG II of IS 12406/Latest. 0.3 mm Veneer sheet is past on both the side of the structure with 0.3 mm thick veneer lipping glued with Kliberit-779.6 glue. Total thick ness of the TOP is Work top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. Gable end is Made up of it is batten structure is which is made up 25m. The above should bedone as per direction of Engineer-in-charge.
2	Very High Back Revolving Chair: Supplying, fitting & fixing ofvery High Back Chair as per given specification and direction of Engineer-in-charge :The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. High BACK SIZE: 47.7 cm. (W) x 76.4 cm. (D) The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps.The adjustable tilting mechanism is designed with the following features:360" revolving type.Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair.Seat/back tilting ratio of 1: 2The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need.The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors. about (W)76.1*(D)76.1*(H)112.7-130.2 SeatHeight 43.1-53.1cm
3	Visitor Mid Back Revolving Chair: Supplying, fitting & fixing ofvisitor Mid Back revolving Chair as per given specification and direction of Engineer-in-charge : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. *MID BACK SIZE: 47.7 cm. (W) x 60.1 cm. (D) The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps.The adjustable tilting mechanism is designed with the following features:360" revolving type.Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair.Seat/back tilting ratio of 1: 2The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need.The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors. About (W)76.1*(D)76.1*(H)96.5-114.0 cm SeatHeight 43.1-53.1cm
4	Sofa Set (Three+One+One)): Supplying, fitting & fixingof3+1+1 Letherite Sof as per given specification and direction of Engineer-in-charge : Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply.Upholstery: Fabric / Leatherette upholstered back and seat.Rubberwood Leg.1 Seater about (W)1070*(D)820*(H)900 & 3 Seater about (W)1890*(D)820*(H)900
5	Steel Storage with Glass Door Unit :Supplying, fitting & fixing of steel storage with Glass Dooras per given specification and direction of Engineer-in-charge : Glass Door Storage about 900 W x 1950 H Upper half Metal - Metal Storage. Storage body- The construction and material of storage body shall be of 0.8mm thick CRCA and skirting shall be of 1.2mm thick CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron. The storage top shall be made up of 2mm thick CRCA sheet with 0.7 mm thick CRCA sheet T-HAT for extra support. Shelf shall be made up of 0.8mm CRCA sheet confirming to IS 513: 2008 with 0.8mm Thick CRCA sheet T-HAT is given for extra support. Shelf shall be mounted with the Metal shelf support pin made of 2mm thick CRCA sheet with Nickel or Chrome plating. Load bearing capacity of the shelf shall be 30Kgs UDL. The construction shall be aesthetically appealing completely welded. M10 screw leveler is given with height adjustment up to 12mm to 15mm.Metal Shutter- Shall be made up of 0.8mm CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron and 0.8 mm CRCA sheet T- HAT is given for extra support and to screw hinges on shutter. Shutter is hinged shutter with equal width hung with 0 Crank on side panel. Multipurpose square lock is used to lock the shutter. PVC flush handles are used in metal shutter. Prelam Shutter-Shall be made up of 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Shutter is hinged shutter with equal width hung with 0 Crank on side panel. Multipurpose square lock is used to lock the shutter. PVC flush handles are used in metal shutter or SS C type SS brush finish handle is used in both the shutter of 96mm CD (center to center distance of handle hole).Glass shutter- Glass shutter can be offered with 4mm toughened clear glass which is surrounded with 1mm thick Aluminum Extrusion frame confirming the IS 733:1983.Shutter is hinged shutter with equal width hung with 0 Crank side panels. Multipurpose square lock is used to lock the shutter. SS C type SS brush finish handle is used in both the shutter of 96mm CD (center to center distance of handle hole.
6	Executive Table (Type-II):Supplying, fitting & fixing of Executive Table (Main Desk, Return Unit, Pedestal) as per given specification and direction of Engineer-in-charge: Main Desk: worksurface 40 mm thick (18 mm MDF batons + 4 mm natural veneer.Legs made from 1.6 mm thick MS clad with strips of MDF.Hollow construction of legs facilltates wire management.Modesty & side panel 18 mm thick MDF,pigmented black and coated with malamine.Drawer Unit constructed from 18 mm thick MDF boards has a combination of 2 box drawers + 1 filing drawer.Drawers mounted on double extension ball slides.Drawer fronts are in natural veneer coated with high gloss polyster.ERU:40 mm thick (18 mm MDF batons + 4 mm natural veneer)veneered portion of worksurface is finished in high gloss polyster & black portion of worksurface has a base coat of polyster and top coat of polyurathane.Modesty Panel 18 mm thick MDF,plgmented black and coated with melamine.Drawer unit constructed from 18 mm thick MDF boards has a combination of 2box drawers + 1 filing drawer.Drawers mounted a double extension ball slides.Drawer fronts are in natural veneer coated with high gloss polyster.Back Unit: worksurface 40 mm thick (18 mm MDF batons + 4 mm natural veneer) veneered portion of worksurface is finished in high gloss polyster & black portion of worksurface has a base coat of polyster and top coat of polyurathane.Door 23 mm thick (18 mm MDF + 4 mm veneer + 1 mm backing decorated laminate.Veneered doors coated with high gloss polyster.Pigmented doors coated with melamine.Doors are mouted on concealed hinges.18 mm thick MDF,pigmented black and coated with melamine.Towers panels 18 mm thick MDF pigmented black.Towers glass 12 mm thick float glass, edge are diamond cut pollshed.Size:Main Desk about 2400 x 1104 x 735,Return UNit: about1400 x 580 x 690,Back Unit:about1860 x 580 x 670,Tower: about1700 x 400 x 1200 mm.
7	Visitor Chair : Supplying, fitting & fixingof visitor Chair as per given specification and direction of Engineer-in-charge :SEAT/BACK ASSEMBLY: The seat and back should bemade up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should bedesigned with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal should be area .BACK SIZE about 47.5 cm. (W) x58.0 cm (H)SEAT SIZE about 47.0 cm. (W) x 48.0 cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression.ARMRESTS :The one-piece armrests should beinjection moulded from black Co-polymer Polypropylene. TUBULAR FRAME: The powder coated ( DFT 40-60 microns ) tubular frame should becantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair. Seat Height - 46.5cm. Height - 89.5cm. Width & Depth of Chair as measured from pedestal - Width-61.4 cm and Depth-64.5 cm (about).
8	Three Seater Sofa (Type-I):Supplying, fitting & fixing of 3 Seater Sofaas per given specification and direction of Engineer-in-charge : OVERALL SIZE -about 1900 X 800 X 700 mm (LxDxH) for 3 seater sofa ofseat height is 430 mm, understructure is made up of Natural Hard wood battens and 12mm THK COMMERCIAL PLYWOOD.High density foam is used for seat and back ,LEATHERITE-ABRASION RESISTANCEin excess of 80,000 cycles, 600 to 650 GSM composition is PVC.
9	One Seater Sofa (Type-I): Supplying, fitting & fixing of 1 Seater Sofaas per given specification and direction of Engineer-in-charge : OVERALL SIZE -about 900 X 800 X 700 mm (LxDxH) for 1 seater sofaof seat height is 430 mm, understructure is made up of Natural Hard wood battens and 12mm THK COMMERCIAL PLYWOOD.High density foam is used for seat and back ,LEATHERITE-ABRASION RESISTANCEin excess of 80,000 cycles, 600 to 650 GSM composition is PVC.
10	Centre Table (Type-I): Supplying, fitting & fixingofCentre Table as per given specification and direction of Engineer-in-charge :Size about 1000W X 600D X 450H Top-Is made up of 50mm thick MDF board confirming to grade SBG II of IS 12406/Latest with PU paint finished. Top is having radius of 55mm in all four corners. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section.Understructure- Legs is made up of 40x5mm thick MS plate confirming the IS grade IS 2385: 1977 with powder coated finish up to 50 to 60 Micron. Intermediate support leg member is made up of 25x16x1.6 pipe confirming the confirming IS-Grade 4932 with powder coated finish up 50 to 60 Micron. Leg dimension is followed as 550Wx225Dx400H, all dimensions are in mm. leg construction is fully welded with MIG welding confirming to IS standard IS 816:1969 and it is welding also tested by confirming to IS 822:1970. The product must be from a Manufacturer having ISO 9001,ISO 14001,Green pro,Latest BIFMA 5.1 certificates for few of its products.
11	Glass Shutter Display unit:Supplying, fitting & fixing ofGlass Shutter Display unit as per given specification and direction of Engineer-in-charge : about W 1050 D 350 H 2050. MATERIAL- Pre-Laminated Particle Board. FINISH -Wenge, THINKNESS - Combination ofabout 18 mm, 9 mm boards.
12	Three Seater Sofa (Type-II):Supplying, fitting & fixing of 3 Seater Fabric upholstered Sofaas per given specification and direction of Engineer-in-charge : 3 seater Size – about 1900 (L) x 750(D) x 825(H) Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply. Upholstery: Fabriccushions and seat.Base-frame: about 40x20x2mm thk MS / SS pipe.Base frame finish: Powder coating (black).SS (brushed finish)
13	One Seater Sofa (Type-II):Supplying, fitting & fixing of 1 Seater Fabric upholstered Sofaas per given specification and direction of Engineer-in-charge :1 seater – about 900(L) x 750(D) x 825(H).Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply.Upholstery: Fabric upholstered cushions and seat.Base-frame: about 40x20x2mm thk PVC with 4 mm bush pipe. Base frame finish: Powder coating (black).SS (brushed finish)
14	Centre Table (Type-II):Supplying, fitting & fixing ofCentre Table as per given specification and direction of Engineer-in-charge :Size about 1200W X 600D X 400H.Top-Is made up of 50mm thick MDF board confirming to grade SBG II of IS 12406/Latest with PU paint finished. Top is having radius of 55mm in all four corners. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. Leg: Solid Rubberwood. The product must be from a Manufacturer having ISO 9001,ISO 14001,Green pro,Latest BIFMA 5.1 certificates for few of its products.
15	Corner Table:Supplying, fitting & fixing of Corner Table as per given specification and direction of Engineer-in-charge : Size ofcorner tableabout 600x 600TOP- Is made up of made about 25mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Reversed chamfering is done on all sides for the table and chamfered area is sealed by white foil. Top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. 4 nos. Solid Rubberwood leg.The product must be from a Manufacturer having ISO 9001,ISO 14001,Green pro,Latest BIFMA 5.1 certificates for few of its products.
16	Thirty Seven Seater Conference Table:Supplying, fitting & fixing of37 Seater Solid Veneer MDFTop ConferenceTable as per given specification and direction of Engineer-in-charge :TOP made up of 18mm MDF (board of grade SBG II of IS 12406/Latest) membrane top with additional 18mm thickness all over the edge with Decorative Aluminum Anodized Profile all over and soft water fall edges. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. GABLE END in rectangular box shape shape to be made of MDF board of grade SBG II of IS 12406/Latest Solid Veneer MDF top withPartial finishDecorated Anodized section at front and back side. MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. Wire management-Electrical wires shall be carried from vertigo. Horizontally wire shall float cable tray, Cable tray shall be made of 0.7mm CRCA sheet confirming to IS 513: 2008.
17	Twenty Two Seater Conference Table:Supplying, fitting & fixing of22 Seater Solid Veneer MDFTop ConferenceTable as per given specification and direction of Engineer-in-charge : TOP made up of 18mm MDF (board of grade SBG II of IS 12406/Latest) membrane top with additional 18mm thickness all over the edge with Decorative Aluminum Anodized Profile all over and soft water fall edges. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. GABLE END in rectangular box shape shape to be made of MDF board of grade SBG II of IS 12406/Latest Solid Veneer MDF top withPartial finishDecorated Anodized section at front and back side. MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. Wire management-Electrical wires shall be carried from vertigo. Horizontally wire shall float cable tray, Cable tray shall be made of 0.7mm CRCA sheet confirming to IS 513: 2008.
18	High backRevolving chair:Supplying, fitting & fixing of High Back revolving Chair as per given specification and direction of Engineer-in-charge : The seat is made up of 1.2 ± 0.1 cm thk. Hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18.The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn.Seat size:about 47.0 cm (W) x 49.5 cm (D).Back size: about45.0 cm (W) x 65.3 cm (H).The HR polyurethane foam is moulded with density = 55 +/- 2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The armrests have an UP-Down adjustment of 8.5 ± 0.5 cm which is provided in armrest structure.Armrest top has an integrated layer of thermoplastic elastomer (TPE).The lumber support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.The height of lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad.Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height.The adjustable tilting mechanism is designed with the following features.360° revolving type.Single point control.Front-pivot for tilt with feel resting on ground ensuring more comfort.Tilt tension adjustment.4-position locking with anti-shock feature.Seat/back tilting ratio of 1:2.The neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.Neckrest is fixed to back assembly through neckrest connector.Neckrest assembly has height adjustment of 4.2 ± 0.5 cm and rotation adjustment of overall 76° ± 2°.The complete neckrest assembly is retro fit to the main chair.The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm.The pedestal is injection moulded in black 30% glass-filled nylon and fitted with 5 nos. twin wheel castors.The pedestal pitch-center dia is Ø 66.1 ± 0.5 cm.The twin wheel castors are injection moulded in black nylon.
19	Mid back Revolving chair:Supplying, fitting & fixing of Mid Back revolving Chair as per given specification and direction of Engineer-in-charge : Medium Back Dimension- Overall Height - about 1060 mm and overall width - about 660 mm,Seat Height -about470 mm, Back Height - about 540 mm Seat Width - about 485 mm. Head rest should be provided for high back. Head rest should be height adjustable.Back rest should be made up of mesh having 100% Polyester. Back rest shoud have adjustable lumbar support. Back rest to be tested with 45 Kg, 120000 cycles @ 10-30 cycles / minSeat should be made of HRFoam fitted on 12 mm ply with fabric upholstery and plastic cover and should have waterfall edge for ergonomic seating. Seat Depth adjustment should be provided. Seatrest should be tested with 55 kg on seat, 120000 cycles @ 10-30 cycles / min.Mechanism - Mechanism should be synchrony with 1:3 ratio. It should have Knee Tilt mechanism with seat slide. It should be BIFMA Compliant and tested with 109 kg on seat for 3,00,000 Cycles.Armrest - Armrest should be adjustable. 4D armrest with PU pad on top. It should be BIFMA compliant. Armrest should be tested with 41 kg on each arm, 60000 cycles. Gaslift - Gaslift should have minimum 100 mm stroke length and should be BIFMA Compliant and tested with 122kg on seat, for 60,000 cycles rotation @ 5-10 rotation / min.Base - Base should be Aluminium die cast base and should be BIFMA compliant and tested for 1450 kg of load.Castors- Castors should be twin wheel castors having 60 mm dia. It should be BIFMA Compliant and tested with 102 kg on seat for 1,00,000 Cycles.Fabric - 100% Polyester. Fabric should be fire retardant and should have passed Cigarette Bud test. Foam - HR Foam.
20	Executive Table (Type-III) :Supplying, fitting & fixing ofExecutive Work Tableas per given specification and direction of Engineer-in-charge :Table about1800 x 900 (WRAP FST TBL PPB /TOP+GAB 37MM THK about 1800WX900DX750H LHS) + Side Credenza + Pedestal 2B1F Work Top- Is made up of 37mm thick dual color edge in Sandwich of 25 thk Prelam particle board and 12 mm thk BSL Prelam particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. Understructure –Gable end is made up of 37mm thick dual color edge in Sandwich of 25 thk Prelam particle board and 12 mm thk BSL Prelam particle board confirming to IS 12823: 1990 in slate grey with 2mm & 0.45mm thick PVC lipping glued with Kliberit-779.6 glue. Sandwiching is done by using 10x12mm KD and 8x12mm Dowel. Gable end shall be fitted to the ground with M6x25 screw leveler with the height adjustment up to 12mm to 15mm.modesty is made up 18 mm thick Prelam particle board confirming to IS 12823: 1990 in slate grey with 2mm & 0.45mm thick PVC lipping glued with Kliberit-779.6 glue. Sandwiching is done at lower edge of the modesty by adding 18 mm thick Prelam particle board confirming to IS 12823: 1990.Storage top - Top shall be made 25mm thick Prelam (BSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue.Top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section.Storage body-Both the LH and RH side panel is made up of 25mm thick Prelam (BSL) particle board confirming to IS 12823: 1990 with 0.45mm thick PVC lipping glued with Kliberit-779.6 glue. Back panel & Bottom is made up of 18mm thick Prelam (BSL) particle board confirming to IS 12823: about 1990 with 2mm & 0.45 mm PVC lipping glued with Kliber
21	Executive High back Revolving chair: Supplying, fitting & fixing of High back revolving chairas per given specification and direction of Engineer-in-charge :SEAT ASSEMBLY: The seat assembly should bemade up of 1.5±0.1 cm. thick hot pressed plywood upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 45.0 cm. (W) x 50.5 cm. (D) . HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density = 45 ±2 kg/m3/ and Hardness 16±2 kgffor 25% compression.BACK ASSEMBLY: The back should bea fabricated tubular frame assy, designed with contoured lumbar support for extra comfort, powder coated ( DFT 40-60 microns ) & upholstered with a high tenacity Polyester mesh fabric. The M.S. tubular frame should bemade of Ø1.9±0.02 cm x 0.2±0.016 cm MS ERW Tube. BACK SIZE:- 46.0 cm (W) x 72.5 cm (H).ARMRESTS: The armrests should bemade of plastic injection moulded nylon. CENTER TILT SYNCHRO mechanism: The mechanism should bedesigned with the following features:•360° revolving type.•Upright position locking.•Tilt tension adjustment.•Seat/back tilting ratio of 1:3 .PNEUMATIC HEIGHT ADJUSTMENT:The pneumatic height adjustment has an adjustment of 10.0±0.3 cm.PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 30% glass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal pitch-center diashould be66.1±0.5 cm.(76.1±1.0 cm with castor). TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in recycled compounded Nylon having 5.0±0.1cm wheel dia and assembled to pedestal Overall Dimensions of Chair. Seat Height-min 42.1cm-max 52.1cm. Height- min 99.1cm - max 101.1cm . Width & Depth of Chair as measured from pedestal - Width- about 76.1 cm and Depth- about 76.1 cm.
22	Mid Back Four Legged Visitor chair :Supplying, fitting & fixing of Mid Back 4 legged visitor chair as per given specification and direction of Engineer-in-charge : Overall Height- 1250 mm Seat Dimension -about500 mmX500 mm. Back Dimension - about 550 mm(H)X 480(W) Back rest should be made up of mesh having 100% Polyester. Back rest shoud have adjustable lumbar support. Back rest to be tested with 45 Kg, 120000 cycles @ 10-30 cycles / min Seat should be made of HRFoam fitted on 12 mm ply with fabric upholstery and plastic cover and should have waterfall edge for ergonomic seating. Seat Depth adjustment should be provided. Seatrest should be tested with 55 kg on seat, 120000 cycles @ 10-30 cycles / min. Understructure made up of MSof Ø25.4 X 2mm thkPipe powder coated with black colorArmrest - fixed.Complete as per proposed layout and direction of Engineer in charge.
23	Glass Door Display storage:Supplying, fitting & fixing of Glass Door Storage as per given specification and direction of Engineer-in-charge : Construction & Material:Rigid Knock down construction.Prime Quality CRCA Steel – 0.8 mm Thick.Sliding Door Arrangement:Full height Sliding Door with top hanging arrangement to prevent derailment.Each door provided with 2 Plastic roller having steel ball bearing for smooth movement of door & less noise.VSDU have Glass door for visibility of the content.Locking & handle :Snap on type aesthetically appealing die cast 5 Lever Cam lock for safe locking.Plastic flush & recessed handle.Shelving :Height wise Adjustable Shelf Mounting.Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum & for half shelf it is 40 Kg.4 Nos. of Adjustable Full Shelf.Top option:1 mm for Metal Top.Accessory:Craddle with pipes for hanging Godrej Instadex files.Leveler:Screw type leveler with hex plastic base (add in unit height min.8 mm & additional 5 mm max for adjustment).Finish:Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).Size:about 1830 x 900 x 450 (GLASS DOOR Full Ht.) mm.Complete as per proposed layout and direction of Engineer in charge.
24	Reception Table: Supplying, fitting & fixing of Reception table as per given specification and direction of EIC:Main Desk size shall be about 1350 Width x 750 Depthx 750 Height.The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT.The Modesty panel shall be in a combination of black & white cedar. ERU size shall be 1200 Width x 450 Depth x 750 Height.The top of ERUshall be 18 mm thick PLT with PVC lipping.The feature of ERU shall be thait is common for both LHS nd RHS.
25	Modular workstation:Supplying, fitting & fixing of modular Workstation 1200 x 600 + 2B1F Ped + KBPT + CPU - Non Sharing with Seperatoras per given specification and direction of Engineer-in-charge :WORKTOP - Made of 25 mm thick Prelaminated particle board with machine pressed PVC edge band on all sides. TILE BASED PARTITION SYSTEM - The Main partition 60mm thick and 1200mm ht. With top Tile in Pinup Board and Laminate marker Board/ Fabric of approved shade and color per workstation , lower Tile in prelaminated finish on both sides. All metal component is in Powder Coated finish with the thickness of 50-60 µ DFT. All vertical component are made up of aluminium extrusions.Partition system have adequate raceway at Single and double levelfor running data & power cables. Raceway Above Table Top and at Skirting Considered (MAIN SPINE ONLY). PRELAM PEDESTAL 3 MS(2B+1F) DRAWER WITH CASTOR about 400WX450DX670H Pedestals to be made of 18mm thick Prelaminated Partical Board. With PVC Edge band and the telescopic slides for mobility of drawers and filers.The drawer is made up of 0.7 mm thick CRCA steel. Handle is Hettich make Ctype.
26	Workstation Mid Back Revolving Chair:Supplying, fitting & fixing of Mid Back Revolving Chairas per given specification and direction of Engineer-in-charge :Revolving Mid Back Chair withFixed type Armrest . The Fabric seat and back, 1 D Arm rest. PU Arm pads, 650 mm dia Nylon base, 50 mm Nylon Castors, Class 4 gas lift, Synchro SINGLE POINT locking position mechanism . All components tested as per BIFMA compliance.Medium Back about (MB) 670mm (H) X 535mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size about510mm (W) X 535mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1.Seat foam made out of moulded Polyurethane foamwith Density: 50-60 Kg/m3, Hardness: 15-20Kgf andTensile strength: 0.9-1.2 Kg/cm2. MECHANISM : SINGLE POINT SYNCHRO MECHANISM : Conventional mechanism with onelever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tiltingangle is 3°~10°. andback tilting angle is 87°~106°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 112mm. Gas lift tested for 1, 00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 3and all applicable ANSI/BIFMA, EN performance standard. BASE : NYLON BASE with castors : The base made up of injection moulded in black glass filled nylon and fitted with 5Nos twin wheel castors. The base is 658mm pitch circle diameter. The base tested for static load of1134Kg as per ANSI / BIFMA X 5.1.
27	Glass Door Storage:Supplying, fitting & fixing of Glass Door Storage as per given specification and direction of Engineer-in-charge :4 Shelves shall have an overall size of about 900mm(W)x450mm(D)x1830mm(H) . The construction shall be rigid knock down construction and Material used shall be prime quality CRCA steel - panels from 0.6 mm thick & front frame . Shelf shall be 0.8 mm thick .Configuration (Door) shall be full height steel hinged door . Locking shall be Plastic Recessed Handle cum Cam lock with 3 way locking mechanism with shooting bolt arrangement . Height wise adjustable shelf mounting , Uniformly distributed load capacity per each full shelf shall be 80 Kg maximum . For Plain 4 Nos. of adjustable full shelves . The top shall be metal and Epoxy Powder coated finishto the thickness of 50 microns .
28	Three Seater Visitor Seating Chair:Supplying, fitting & fixing of 3 seater Chair with cusionas per given specification and direction of Engineer-in-charge : The Premium Lounge chair is a flexing-back lounge seating system standing on beam with side frame assemblies.The side frame assembly is fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It is made of a MS. E.R.W. tube dia. 3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The ends are fitted with ABS moulded end caps.It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube dia.3.81cm. (1 1/2”) x 14 BG. thk.and black powder coated. The seat/back assemblies are mounted on one of the tie-member which hasabout 5cm x 5.5cm long x 0.5cm. thk MS. Std. angles welded to mount the seat and back.The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm³. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover.SEAT SIZE: about 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T)for one seat.The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm³. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholstery cover.BACK SIZE: about 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) for one back.The adj. glide is injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface.
29	One Seater Visitor Seating Chair:Supplying, fitting & fixing of one seater Chair with cusionas per given specification and direction of Engineer-in-charge :The Premium Lounge chair is a flexing-back lounge seating system standing on beam with side frame assemblies.The side frame assembly is fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It is made of a MS. E.R.W. tube dia. 3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The ends are fitted with ABS moulded end caps.It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube dia.3.81cm. (1 1/2”) x 14 BG. thk.and black powder coated. The seat/back assemblies are mounted on one of the tie-member which has about5cm x 5.5cm long x 0.5cm. thk MS. Std. angles welded to mount the seat and back.The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm³. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover.SEAT SIZE: about 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T)for one seat.The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm³. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholstery cover.BACK SIZE: about 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) for one back.The adj. glide is injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface
30	Auditorium chair: Supplying, fitting & fixing of Auditorium chair as per given specification and direction of Engineer-in-charge : MS black powder coated understructure with integrated, auto tip-up mechanism.Footprint area of base plate: about 150mm X 230mm X 5mm thick.Backrest supporting beam width: about460mm (L) X 80 X 40 – 14 BG HR tube.Understructure fixed to ground by foundation expansion bolts M10 X 100 with washer and nut.Seat assembly is made of Polyurethane foam moulded with 1.5 cm. thick plywood insert as per the following dimensions:Seat size:Depth: 420.0 mm (D).Width @ rear: 440.0 mm.Width @ front: 410.0 mm.Effective seat width (W): 460.0 MM.Effective seat depth (D): 450.0 MM.Back assembly consists of Polyurethane foam moulded with MS tubular frame insert. The insert is composed of Diameter 19mm x 16BG MS tubular frame with flexible nylon support straps running across the length and width of the frame.Back size:Height: 540.0 mm (H).Width @ top: 340.0 mm.Width @ seat level: 460.0 mm.The polyurethane foam used for seat and back is moulded with density = 45+ 2 kg/c.m.Vacuum formed plastic back & Mech. cover with 3mm. and 2mm. respectively avg. thickness.Armrest understructure is upholstered PU foam moulded with MS insert and Arm tops are made of seasoned wood.Armrest width = 70mm and are offered as common / individual armrest between chairs.Option of PU Arm tops also available.
31	Mid back Stage chair:Supplying and Installationof Midback Chair with cusionas per given specification and direction of Engineer-in-charge : Medium Back chair without headrest having .SeatDimensions- Seat Size about 550 mm (H) X 490 mm (W). Back Rest Dimensions - Backrest Size about635mm(H) X 480mm (W).The Back frame is made up of dia. 12 mm Bright Bar welded with 8mm thk MS plate. Powder coated in Black colour. Fixed Newar belt in lumber support position. Upholstery with Mesh fabric. PU foam pasted on both side & upholstered with polyester fabric.Back rest to be tested with 45 Kg, 120000 cycles @ 10-30 cycles / min. The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size about495 mm (W) X 495 mm (D). Seatrest should be tested with 55 kg on seat, 120000 cycles @ 10-30 cycles / min,• Density (IS-7888-1976) : 50-55 Kg/m3. Mechanism -SINGLE POINT SYNCHRO MECHANISM: Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm. Also it has the back tension adjustment knob. . It should be BIFMA Compliant and tested with 109 kg on seat for 3,00,000 Cycles. Armrest -FIXED ARM : The arm rest made up of injection moulded from Black polypropylene - size 240mm (L) x 85mm (W). Gaslift - Gaslift should have minimum 100 mm stroke length and should be BIFMA Compliant and tested with 122kg on seat, for 60,000 cycles rotation @ 5-10 rotation / min. Base - Base should be Nylon and should be BIFMA compliant and tested for 1150 kg of load. Castors- Castors should be twin wheel castors having 60 mm dia. It should be BIFMA Compliant and tested with 102 kg on seat for 1,00,000 Cycles. Fabric - 100% Polyester. Fabric should be fire retardant and should have passed Cigarette Bud test. Foam - HR Foam.