Construction Of 6 Nos Type Ii Quarters For Irbn At Amini Balance Work Including Septic Tank Soak Pit Well And Manhole Construction Of 6 Nos Type Ii Quarters For Irbn At Amini Balance Work Including Septic Tank Soak Pit Well And Manhole
Tender Value
Ref. Documents
Estimated cost
Bid Submission
05 Apr 2022
0 days left
EMD
1.59 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
amini → Lakshadweep
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 6 Nos Type Ii Quarters For Irbn At Amini Balance Work Including Septic Tank Soak Pit Well And Manhole Construction Of 6 Nos Type Ii Quarters For Irbn At Amini Balance Work Including Septic Tank Soak Pit Well And Manhole
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 01-Apr-2022 | Date correction | Date | 05-Apr-2022 |
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing of the ground including removing vegetation and inequalities to 50 m and lift up to 1.5 m. All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 3 | All kinds of soil. |
| 4 | up to 1.50 mtr to 3 mtr |
| 5 | up to 3 mtr to 4.5 mtr |
| 6 | up to 4.50 mtr to 6 mtr |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 9 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 10 | Reinforced cement concrete work in well-steining, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 11 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete, up to floor V level.Thermo-Mechanically treated bars of grade Fe-500D or more |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form forWell steining |
| 14 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:6 (1 cement : 6 coarse sand). |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 17 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 18 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Second class teak wood |
| 19 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:Butt hinges and necessary screws shall be paid separately)Second class teak wood , 35 mm thick shutters |
| 20 | Providing and fixing karimaruthu wood or equivalent 25 mm squre wooden bars at required spacing in wooden frames of windows and clerestory windows |
| 21 | Providing 40x5 mm flat iron hold fast 40 cm long ncluding fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 22 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm |
| 23 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : |
| 24 | 250x10 mm |
| 25 | 100x10 mm |
| 26 | Providing and fixing bright finished brass handles with screws etc. complete: |
| 27 | 125 mm |
| 28 | 100mm |
| 29 | Providing and fixing Bright finished brass casement stay with necessary fittings and screws250 mm weighing not less than 280gms |
| 30 | Providing and fixing Aluminium curtain rods with Aluminium brackets: 20 mm dia (heavy type) |
| 31 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuiltedging on both sides. The styles and rails mitred and joined at the corners by meansof M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ± 0.1 mm wall thickness. The lock ail made up of’H’ section, a UPVC hollow section of size 100x24 mm and 2 mm ± r 0.2 mm wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ± 0.1 mm wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 32 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in- Charge. |
| 33 | Providing and fixingStainless steel (Grade 316) railing made of hollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fastners, stainless steel bolts etc,. of required size on the top of the floor or the side of waist slab with suitable arrangements as per approval of Engineer-in- Charge. |
| 34 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 35 | Providing and laying 10 mm thick vitrified floor tiles in different sizes with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x800 mm |
| 36 | Providing and laying 10 mm thick Vitrified tiles in different sizes with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 800x800 mm |
| 37 | Providing and fixing 8 mm thick Ist quality ceramic glazed wall tiles conforming to IS: 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 38 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 39 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 40 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 41 | 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) |
| 42 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) |
| 43 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 44 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 45 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufactures specifications two or more coats applied on walls @1.25ltr/10 sqm) over including one coat of special primer applied @ 0.75 ltr/10 sqm |
| 46 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 47 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 48 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge.With granite stone of area less than 0.50 sqm |
| 49 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 50 | a) 15 mm nominal bore outer dia pipe |
| 51 | b) 32 mm nominal bore outer dia pipe |
| 52 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.external work |
| 53 | a) 15 mm nominal bore outer dia pipe |
| 54 | b) 20 mm nominal bore outer dia pipe |
| 55 | Providing and fixing brass bib cock of approved quality |
| 56 | a) 15 mm nominal bore |
| 57 | b) 20 mm nominal bore |
| 58 | Providing and fixing brass stop cock of approved quality |
| 59 | a) 15 mm nominal bore |
| 60 | b) 20 mm nominal bore |
| 61 | Providing and fixing G.M. full way wheel valve of approved quality and manufacture complete. 25 mm nominal bore |
| 62 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter |
| 63 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 64 | Providing and placing Sintexwater tank on terrace up to the rooftwo level of approved quality and manufacture complete (a) 500 Litre capacity (6Nos) |
| 65 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 66 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 67 | Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink asper IS 13983with CI brackets stainless steel plug 40 mm ,including painting of fittings and brackets, cutting and making good the wallswhere required. Kitchen sink with drain board 510x1040 mm bowl deth 250 mm |
| 68 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 69 | Providing and fixing towel rail brackets fixed to wooden cleat with scerws and washers .(a) 600 x 20 mm CP brass towel rail with brackets 600mm long towel rail brackets with total length of 645mm width 78mm and effective height of 88 mm weighinig not less than 190 gms. |
| 70 | Providing and fixing PTMT liquid soap containerwith CP brass lid and bracket fixed to woodencleatswith scerws and washers . |
| 71 | Providing anf fixing on wall face PVC. soil waste and vent pipe. 75mm dia pipes |
| 72 | Providing,laying and P.V.C pipes grade \"A\" with stiff mixture of 1:3 (1 cemenr 3 metal sand) including testing of joints etc. complete. |
| 73 | 110mm dia |
| 74 | 90mm dia |
| 75 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand cast iron S&S as per IS: 3989 |
| 76 | Providing and laying cement concrete 1:5:10 (1 cement : 5 metal sand : 10 graded stone aggregate 40 mm nominal size) upto haunches of pipes including bed concrete as per standard design .100mm dia pipe |
| 77 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 78 | Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : |
| 79 | 125X90X4.00mm |
| 80 | 50x40x2.50mm |
AI Tender Summary
Tender Timeline
Apr 01, 2022
11:30 IST
Tender Published
Tender notice published.
Completed
Apr 05, 2022
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedApr 05, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 06, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender